The following race conditions can happen when a serial port is used
as console.
Case1: CPU_B is used to detect an interrupt from a serial port,
but it can have interrupts disabled during the waiting time.
Case2: CPU_B clears UART_IER just after CPU_A sets UART_IER and then
a serial port may not make an interrupt.
Case3: CPU_A sets UART_IER just after CPU_B clears UART_IER.
This is an unexpected behavior for serial8250_console_write().
CPU_A [autoconfig_irq] | CPU_B [serial8250_console_write]
----------------------------|---------------------------------------
|
probe_irq_on() | spin_lock_irqsave(&port->lock,)
serial_outp(,UART_IER,0x0f) | serial_out(,UART_IER,0)
udelay(20); | uart_console_write()
probe_irq_off() |
| spin_unlock_irqrestore(&port->lock,)
Case1 and 2 can make autoconfig_irq() failed.
In these cases, the console doesn't work in interrupt mode and
"input overrun" (which can make operation mistakes) can happen
on some systems. Especially in the Case1, It is known that the
problem happens with high rate every boot once it occurs
because the boot sequence is always almost same.
port mutex makes sure that the autoconfig operation is exclusive of
any other concurrent HW access except by the console operation.
console lock is required in autoconfig_irq().
Signed-off-by: Taichi Kageyama <t-kageyama@cp.jp.nec.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
8250/Kconfig:config SERIAL_8250_LPC18XX
8250/Kconfig: bool "NXP LPC18xx/43xx serial port support"
...meaning that it currently is not being built as a module by anyone.
When targetting orphaned modular code in non-modular drivers, this
came up. Joachim indicated that the driver was actually meant to
be tristate but ended up bool by accident. So here we make it
tristate instead of removing the modular code that was essentially
orphaned.
Suggested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CIR type serial ports aren't real serial ports.
This is just a way to prevent legacy 8250 serial
driver from probing and eventually binding some
resources.
Since in current state such ports aren't providing
any real functionality and it is not possible
to change their type via setserial/ioctl(TIOCSSERIAL)
(due to UPF_FIXED_PORT flag set on them)
it is simpler and cleaner to not register them at all
with serial core.
Print a short message in this case so it is known
to user what has happened.
This way checks for PORT_8250_CIR in serial port
callbacks can be removed too, since they won't
ever be called.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() returns an int and as such it
might fail. So the result is that I kindly asked to insert 48 bytes and
the function only insterted 32.
I have no idea what to do with the remaining 16 so I think dropping them
is the only option. I also increase the buf_overrun counter so userpace
has a clue that we lost bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The split of the 8250 driver into a 8250_base/8250.ko resulted in a
lack of a license for the 8250_base.ko module. This caused the module
to fail to load and the kernel to be tainted. Add the appropriate
MODULE_LICENSE to 8250_port.c, which is always compiled into
8250_base.ko
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
That bitfield is modified by read + or + write operation. If someone
sets any of the other two bits it might render the lock useless.
While at it, remove other bitfields as well to avoid more such
errors.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250-omap driver requires the DMA-engine driver to support the pause
command in order to properly turn off programmed RX transfer before the
driver stars manually reading from the FIFO.
The lacking support of the requirement has been discovered recently. In
order to stay safe here we disable RX-DMA completly on probe.
The rx_dma_broken assignment on probe could be removed once we working
pause function in omap-dma.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the serial core is informed that this device is doing
automatic flow control, it is not necessary to alter CTS and
DCTS of the MSR as the core no longer attempts stop the port
in uart_handle_cts_change().
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512
We had add RS232/485 RTS control with fecf27a373. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).
This patch will modify 2 sections.
One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.
The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RS485 control for Fintek F81504/508/512
F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.
When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.
When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.
When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.
We will force 0x01 on pci_fintek_setup().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XR17V35X UART needs the ECB bit set in its XR_EFR
register to enable access to IER [7:5], ISR [5:4], FCR[5:4],
MCR[7:5], and MSR [7:0].
Also reset the IER register to mask interrupts after access
to all bits of this register has been enabled.
This makes my 8-port XR17V35X working with the in-kernel
serial driver.
Cc: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An already-active sender can swamp the interrupt handler with
"too much work" if the rx interrupts are enabled when the fifo is
disabled and operating in single-byte mode.
Defer rx and line status interrupt enable until after the fifos
are enabled in set_termios(), but at least initialize the shadow
IER value with the interrupts which will be enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ed71871bed ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override
However recent updates to core, specifically ebc5e20082 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3fee
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP h/w-assisted IXON flow control is borked. The transmitter becomes
stuck if XON is never received; clearing the fifos or resetting the
rx flow control bits has no effect.
Remove auto-IXANY as well, since without auto-IXON, it has no purpose.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to Advisory 21 as documented in AM437x errata document,
UART module cannot be disabled once DMA is used. The only
workaround is to softreset the module before disabling it.
DRA7x UARTs are compatible to AM437x UARTs in terms of
this errata and prescribed workaround.
Enable usage of workaround for this errata on DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM335x, AM437x and DRA7x SoCs have an errata[1] due to which UART
cannot be idled after it has been used with DMA.
OMAP3 has a similar sounding errata which has been worked around
in a2fc36613a ("ARM: OMAP3: Use manual idle for UARTs
because of DMA errata"). But the workaround used there does not
apply to AM335x, AM437x SoCs.
After using DMA, the UART module on these SoCs must be soft reset
to go to idle.
This patch implements that errata workaround. It is expected that
UART will be used with DMA so no explicit check for DMA usage
has been added for errata applicability.
MDR1 register needs to be restored right after soft-reset because
"UART mode" must be set in that register for module wake-up on AM335x
to work. As a result, SCR register is now used to determine if
context was lost during sleep.
[1] See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of of_machine_is_compatible() for handling AM335x specific
"DMA kick" quirk in 8250_omap driver makes it ugly to extend the
quirk for other platforms. Instead use a new compatible.
The new compatible will also make it easier to take care of
other quirks on AM335x and like SoCs.
In order to not break backward DTB compatibility for users of
8250_omap driver on AM335x based boards, existing use of
of_machine_is_compatible() has not been removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The silicon errata[1] workaround implemented in a follow-on
patch, "serial: 8250_omap: workaround errata on disabling
UART after using DMA", requires MDR1 register programming.
Extract MDR1 register update into helper function,
omap8250_update_mdr1() to help with that.
[1] Advisory 21 in http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_device infrastructure has a suspend_noirq hook which
runtime suspends all devices late in the suspend cycle (see
_od_suspend_noirq() in arch/arm/mach-omap2/omap_device.c)
This leads to a NULL pointer exception in 8250_omap driver
since by the time omap8250_runtime_suspend() is called, 8250_dma
driver has already set rxchan to NULL via serial8250_release_dma().
Make an explicit check to see if rxchan is NULL in
runtime_{suspend|resume} hooks to fix this.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be configured for io addresses different than the standard.
Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip can be configured to use entry key different than 0x77. Try all the
valid keys until one gives out the right chip id.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some chips with the same interface but different chip ip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be connected at address 0x4e and also 0x2e.
Add some logic to find out the address of the chip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the port index and the line id in a private structure.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bhUU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Introduce a driver suitable for use with the UARTs present in
Ingenic SoCs such as the JZ4740 & JZ4780. These are described as being
ns16550 compatible but aren't quite - they require the setting of an
extra bit in the FCR register to enable the UART module. The serial_out
implementation is the same as that in arch/mips/jz4740/serial.c - which
will shortly be removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-serial@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The internal clock of the master chip, which is usually 125MHz, is only half
(62.5MHz) for the slave chips. So we have to adjust the uartclk for all the
slave ports. Therefor we add a new function to determine if a slave chip is
present and update pci_xr17v35x_setup accordingly.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial port driver for the 8250-based UART found on LPC18xx/43xx
devices. The UART is 16550A compatible with additional features
like RS485 support, synchronous mode, IrDA, and DMA.
For now only basic UART and RS485 operation is supported.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver for on-chip UART used on UniPhier SoCs.
This hardware is similar to 8250, but the register mapping is
slightly different:
- The offset to FCR, MCR is different.
- The divisor latch access bit does not exist. Instead, the
divisor latch register is available at offset 9.
This driver overrides serial_{in,out}, dl_{read,write} callbacks,
but wants to borrow most of code from 8250_core.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many new Intel SoCs the UART has an integrated DMA engine
(iDMA). In order to use it a special filter function is needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_set_mctrl() is a void type function. Returning something
does not look nice.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the mediatek serial port driver is built-in, but serial
console is disabled in Kconfig (e.g. when the serial driver
itself is a loadable module), we get this build error:
drivers/built-in.o: In function `early_mtk8250_setup':
undefined reference to `early_serial8250_setup'
To avoid that problem, this patch encloses the early_mtk8250_setup
function in #ifdef CONFIG_SERIAL_8250_CONSOLE, the same symbol
that guards the early_serial8250_setup function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port.fifosize member has already been copied at 8 lines above.
Maybe the compiler optimization can clean it away, but just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When nr_uarts was set to 0 (via config or 8250_core.nr_uarts), we crash
early on x86 because serial8250_isa_init_ports dereferences base_ops
which remains NULL. In fact, there is nothing to do for all the callers
of serial8250_isa_init_ports if there are no uarts.
Based on suggestions by Peter Hurley.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 8250 MTK UART driver to support earlycon device tree.
Earlycon take effect by
add "earlycon" in kernel boot argument
add "linux,sdtout-path" property in device tree file
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
