The MediaTek MT7621 SoC device contains a 7530 switch, and the existing
linux kernel 7530 DSA switch driver can be used with it.
The bulk of the changes required stem from the 7621 having different
regulator and pad setup. The existing setup of these in the 7530
driver appears to be very specific to its implemtation in the Mediatek
7623 SoC. (Not entirely surprising given the 7623 is a quad core ARM
based SoC, and the 7621 is a dual core, dual thread MIPS based SoC).
Create a new devicetree type, "mediatek,mt7621", to support the 7530
switch in the 7621 SoC. There appears to be no usable ID register to
distinguish it from a 7530 in other hardware at runtime. This is used
to carry out the appropriate configuration and setup.
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 can treat each port as either VLAN-unaware port or VLAN-aware port
through the implementation of port matrix mode or port security mode on
the ingress port, respectively. On one hand, Each port has been acting as
the VLAN-unaware one whenever the device is created in the initial or
certain port joins or leaves into/from the bridge at the runtime. On the
other hand, the patch just filling the required callbacks for VLAN
operations is achieved via extending the port to be into port security
mode when the port is configured as VLAN-aware port. Which mode can make
the port be able to recognize VID from incoming packets and look up VLAN
table to validate and judge which port it should be going to. And the
range for VID from 1 to 4094 is valid for the hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N platform which
includes 7-port Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY.
Among these ports, The port from 0 to 4 are the user ports connecting
with the remote devices while the port 5 and 6 are the CPU ports
connecting into Mediatek Ethernet GMAC.
For port 6, it can communicate with the CPU via Mediatek Ethernet GMAC
through either the TRGMII or RGMII which could be controlled by phy-mode
in the dt-bindings to specify which mode is preferred to use. And for
port 5, only RGMII can be specified. However, currently, only port 6 is
being supported in this DSA driver.
The driver is made with the reference to qca8k and other existing DSA
driver. The most of the essential callbacks of the DSA are already
support in the driver, including tag insert for user port distinguishing,
port control, bridge offloading, STP setup and ethtool operation to allow
DSA to model each user port into a standalone netdevice as the other DSA
driver had done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
