The ctpio_dmabuf_start entry is not actually a stat and shouldn't
be exposed to ethtool.
Fixes: 2c0b6ee837 ("sfc: expose CTPIO stats on NICs that support them")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the type of length is u16, it will overflow. So change it
to u32.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NSP default buffer is a piece of NFP memory where additional
command data can be placed. Its format has been copied from
host buffer, but the PCIe selection bits do not make sense in
this case. If those get masked out from a NFP address - writes
to random place in the chip memory may be issued and crash the
device.
Even in the general NSP buffer case, it doesn't make sense to have the
PCIe selection bits there anymore. These are unused at the moment, and
when it becomes necessary, the PCIe selection bits should rather be
moved to another register to utilise more bits for the buffer address.
This has never been an issue because the buffer used to be
allocated in memory with less-than-38-bit-long address but that
is about to change.
Fixes: 1a64821c6a ("nfp: add support for service processor access")
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using wicked with a lan78xx device attached to the system, we
end up with ethtool commands issued on the device before an ifup
got issued. That lead to the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000039c
pgd = ffff800035b30000
[0000039c] *pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
Modules linked in: [...]
Supported: Yes
CPU: 3 PID: 638 Comm: wickedd Tainted: G E 4.12.14-0-default #1
Hardware name: raspberrypi rpi/rpi, BIOS 2018.03-rc2 02/21/2018
task: ffff800035e74180 task.stack: ffff800036718000
PC is at phy_ethtool_ksettings_get+0x20/0x98
LR is at lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
pc : [<ffff0000086f7f30>] lr : [<ffff000000dcca84>] pstate: 20000005
sp : ffff80003671bb20
x29: ffff80003671bb20 x28: ffff800035e74180
x27: ffff000008912000 x26: 000000000000001d
x25: 0000000000000124 x24: ffff000008f74d00
x23: 0000004000114809 x22: 0000000000000000
x21: ffff80003671bbd0 x20: 0000000000000000
x19: ffff80003671bbd0 x18: 000000000000040d
x17: 0000000000000001 x16: 0000000000000000
x15: 0000000000000000 x14: ffffffffffffffff
x13: 0000000000000000 x12: 0000000000000020
x11: 0101010101010101 x10: fefefefefefefeff
x9 : 7f7f7f7f7f7f7f7f x8 : fefefeff31677364
x7 : 0000000080808080 x6 : ffff80003671bc9c
x5 : ffff80003671b9f8 x4 : ffff80002c296190
x3 : 0000000000000000 x2 : 0000000000000000
x1 : ffff80003671bbd0 x0 : ffff80003671bc00
Process wickedd (pid: 638, stack limit = 0xffff800036718000)
Call trace:
Exception stack(0xffff80003671b9e0 to 0xffff80003671bb20)
b9e0: ffff80003671bc00 ffff80003671bbd0 0000000000000000 0000000000000000
ba00: ffff80002c296190 ffff80003671b9f8 ffff80003671bc9c 0000000080808080
ba20: fefefeff31677364 7f7f7f7f7f7f7f7f fefefefefefefeff 0101010101010101
ba40: 0000000000000020 0000000000000000 ffffffffffffffff 0000000000000000
ba60: 0000000000000000 0000000000000001 000000000000040d ffff80003671bbd0
ba80: 0000000000000000 ffff80003671bbd0 0000000000000000 0000004000114809
baa0: ffff000008f74d00 0000000000000124 000000000000001d ffff000008912000
bac0: ffff800035e74180 ffff80003671bb20 ffff000000dcca84 ffff80003671bb20
bae0: ffff0000086f7f30 0000000020000005 ffff80002c296000 ffff800035223900
bb00: 0000ffffffffffff 0000000000000000 ffff80003671bb20 ffff0000086f7f30
[<ffff0000086f7f30>] phy_ethtool_ksettings_get+0x20/0x98
[<ffff000000dcca84>] lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
[<ffff0000087cbc40>] ethtool_get_settings+0x68/0x210
[<ffff0000087cc0d4>] dev_ethtool+0x214/0x2180
[<ffff0000087e5008>] dev_ioctl+0x400/0x630
[<ffff00000879dd00>] sock_do_ioctl+0x70/0x88
[<ffff00000879f5f8>] sock_ioctl+0x208/0x368
[<ffff0000082cde10>] do_vfs_ioctl+0xb0/0x848
[<ffff0000082ce634>] SyS_ioctl+0x8c/0xa8
Exception stack(0xffff80003671bec0 to 0xffff80003671c000)
bec0: 0000000000000009 0000000000008946 0000fffff4e841d0 0000aa0032687465
bee0: 0000aaaafa2319d4 0000fffff4e841d4 0000000032687465 0000000032687465
bf00: 000000000000001d 7f7fff7f7f7f7f7f 72606b622e71ff4c 7f7f7f7f7f7f7f7f
bf20: 0101010101010101 0000000000000020 ffffffffffffffff 0000ffff7f510c68
bf40: 0000ffff7f6a9d18 0000ffff7f44ce30 000000000000040d 0000ffff7f6f98f0
bf60: 0000fffff4e842c0 0000000000000001 0000aaaafa2c2e00 0000ffff7f6ab000
bf80: 0000fffff4e842c0 0000ffff7f62a000 0000aaaafa2b9f20 0000aaaafa2c2e00
bfa0: 0000fffff4e84818 0000fffff4e841a0 0000ffff7f5ad0cc 0000fffff4e841a0
bfc0: 0000ffff7f44ce3c 0000000080000000 0000000000000009 000000000000001d
bfe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
The culprit is quite simple: The driver tries to access the phy left and right,
but only actually has a working reference to it when the device is up.
The fix thus is quite simple too: Get a reference to the phy on probe already
and keep it even when the device is going down.
With this patch applied, I can successfully run wicked on my system and bring
the interface up and down as many times as I want, without getting NULL pointer
dereferences in between.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently counting packets with CHECKSUM_COMPLETE as
"hw_rx_csum_ok". This is confusing. Add a new counter.
To make sure it fits in the same cacheline move the less used
error counter to a different location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a thermal monitoring device for the Marvell 88x3310, which updates
once a second. We also need to hook into the suspend/resume mechanism
to ensure that the thermal monitoring is reconfigured when we resume.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would be passing 0 instead of NULL as the rsp argument to
mt7530_fdb_cmd(), fix that.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparse complains about the following warnings:
drivers/net/dsa/b53/b53_mmap.c:33:31: warning: incorrect type in
initializer (different address spaces)
drivers/net/dsa/b53/b53_mmap.c:33:31: expected unsigned char
[noderef] [usertype] <asn:2>*regs
drivers/net/dsa/b53/b53_mmap.c:33:31: got void *priv
and indeed, while what we are doing is functional, we are dereferencing
a void * pointer into a void __iomem * which is not great. Just use the
defined b53_mmap_priv structure which holds our register base and use
that.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add a shell script to get Clang version
- improve portability of build scripts
- drop always-enabled CONFIG_THIN_ARCHIVE and remove unused code
- rename built-in.o which is now thin archive to built-in.a
- process clean/build targets one by one to get along with -j option
- simplify ld-option
- improve building with CONFIG_TRIM_UNUSED_KSYMS
- define KBUILD_MODNAME even for objects shared among multiple modules
- avoid linking multiple instances of same objects from composite objects
- move <linux/compiler_types.h> to c_flags to include it only for C files
- clean-up various Makefiles
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=N5BL
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add a shell script to get Clang version
- improve portability of build scripts
- drop always-enabled CONFIG_THIN_ARCHIVE and remove unused code
- rename built-in.o which is now thin archive to built-in.a
- process clean/build targets one by one to get along with -j option
- simplify ld-option
- improve building with CONFIG_TRIM_UNUSED_KSYMS
- define KBUILD_MODNAME even for objects shared among multiple modules
- avoid linking multiple instances of same objects from composite
objects
- move <linux/compiler_types.h> to c_flags to include it only for C
files
- clean-up various Makefiles
* tag 'kbuild-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
kbuild: get <linux/compiler_types.h> out of <linux/kconfig.h>
kbuild: clean up link rule of composite modules
kbuild: clean up archive rule of built-in.a
kbuild: remove partial section mismatch detection for built-in.a
net: liquidio: clean up Makefile for simpler composite object handling
lib: zstd: clean up Makefile for simpler composite object handling
kbuild: link $(real-obj-y) instead of $(obj-y) into built-in.a
kbuild: rename real-objs-y/m to real-obj-y/m
kbuild: move modname and modname-multi close to modname_flags
kbuild: simplify modname calculation
kbuild: fix modname for composite modules
kbuild: define KBUILD_MODNAME even if multiple modules share objects
kbuild: remove unnecessary $(subst $(obj)/, , ...) in modname-multi
kbuild: Use ls(1) instead of stat(1) to obtain file size
kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS
kbuild: move include/config/ksym/* to include/ksym/*
kbuild: move CONFIG_TRIM_UNUSED_KSYMS code unneeded for external module
kbuild: restore autoksyms.h touch to the top Makefile
kbuild: move 'scripts' target below
kbuild: remove wrong 'touch' in adjust_autoksyms.sh
...
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
Note that the driver previously used dev_warn() to suggest using a
different slot, but pcie_print_link_status() uses dev_info() because if the
platform has no faster slot available, the user can't do anything about the
warning and may not want to be bothered with it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Use the new pci_bandwidth_available() function to calculate maximum
available bandwidth through the PCI chain instead of computing it ourselves
with mlx5e_get_pci_bw().
This is used to detect when the device is capable of more bandwidth than is
available in the current slot. The driver may adjust compression settings
accordingly.
Note that pci_bandwidth_available() accounts for PCIe encoding overhead, so
it is more accurate than mlx5e_get_pci_bw() was.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: remove mlx5e_get_pci_bw() wrapper altogether]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Use pcie_print_link_status() to report PCIe link speed and possible
limitations.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
driver and timer driver), which has been through 7 rounds of review on mailing
list.
It is able to boot to shell and passes most LTP-2017 testsuites in nds32 AE3XX
platform.
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78
Copied below is the ChangeLog that contains the history of this patch set:
Changes in v7:
- Update cpu binding document to add "andestech,nds32v3" as fallback
- Remove unnecessary configs of arch/nds32/Kconfig
- Use GENERIC_CALIBRATE_DELAY
- Add more help texts for minimum CPU type config
- Update defconfig because of Kconfig changed and bug fixed
- Move early_trap_init() declaration to nds32.h
- Refine dma.c
- Remove apply_relocate() in module.c and include <linux/moduleloader.h> to catch it
- Add do_kernel_restart() in machine_restart()
- Clean up setup.c to remove CONFIG_VGA_CONSOLE and some extern declaration functions
- Add negative dependency for VGA_CONSOLE on nds32
- Refine ptrace.c and arch/nds32/include/asm/ptrace.h
- Refine syscall restart flow and arch/nds32/kernel/signal.c
- Fix a bug in VDSO
- Remove the handling for kernel code unaligned accessing
- Add a description for unaligned access handling in git commit message.
- Rebase to v4.16-rc1
- Replace ACCESS_ONCE with READ_ONCE
- Replace atomic_long_dec(&mm->nr_ptes) with mm_dec_nr_ptes(mm)
- Remove print_symbol(%s) with printk(%pS)
- Add bpf_perf_event.h
- Remove init_stack and init_thread_info
Changes in v6:
- Refine naming for atl2c
- Refine ae3xx.dts
- Remove CONFIG_TIMER_ATCPIT100 in defconfig
- Refine elf.h
- Fix a vdso bug
- Separate arch patchset and timer patchset
- To select TIMER_OF in drivers/clocksource/Kconfig instead of arch/nds32/Kconfig
Changes in v5:
- Remove __NR__llseek and sys_mmap()
- Add a comment to explain that we don't have clocksource cycle counter in the CPU
- Add volatile in iounmap()
- Fix typo Featuretures to Features
- Replace CPU_CACHE_NONALIASING with !CPU_CACHE_ALIASING
- Fix a endian bug when we try to get val = of_get_property(cpu,"clock-frequency", NULL)
- Add screen_info to fix the building error when CONFIG_ VGA_CONSOLE is enabled
- Remove unnecessary msync()
- Add depends on !64BIT || BROKEN for faraday Kconfig because the descriptor only supports 32bit
- Add atl2c binding document
- Remove unnecessary include headers
- Fix a vector table bug. It placed wrong vector handlers for 2 exceptions.
- Fix a vdso bug. It may encounter TLB multi-hit exception because we accidently set it as a global page.
- Add proper isb and barrier after some cache operations
- Fix a bug in system call restart flow. $r0 ~ $r5 does not be recovered before restarting system call
- Fix the build errors for OpenRISC and SPARC because io.h changed.
- Update ae3xx.dts to support atl2c.
Changes in v4:
- Add atcpit100 timer driver due to it include vdso implementations and sent
them together with nds32 may help reviewer to review.
- Update ae3xx.dts for atcpit100 clock setting and remove vdso settings.
- To get cycle counter register by timer driver instead of dts.
- Use "depends on NDS32 || COMPILE_TEST" in atcpit100 driver because it is needed for nds32 vdso
- Update defconfig becasue kconfig rename from CONFIG_CLKSRC_ATCPIT100 to CONFIG_TIMER_ATCPIT100
- Remove ag101p.dts because we are not yet ready for ag101p platform.
- Update copyright style to SPDX-License-Identifier
- Include <linux/uaccess.h> instead of <asm/uaccess.h>
- Add local_irq_save()/local_irq_restore() to protect SR_TLB_VPN in update_mmu_cache().
- Update cpu_dcache_inval_all implementation to make sure all level cache are writeback.
Changes in v3:
- Use arch's io.h instead of generic one
- Add andestech-boards binding document
- Update nds32/cpus.txt binding document
- Remove atcpit100 timer drivers
- Select NO_BOOTMEM and delete HAVE_MEMBLOCK_NODE_MAP
- make CPU_BIG_ENDIAN and CPU_LITTLE_ENDIAN are dependent
- Add cpu type to select HWZOL/CPU_CACHE_ALIASING
- Change CPU_CACHE_NONALIASING to CPU_CACHE_ALIASING
- Remove bootarg from device tree script
- Update ag101p.dts and ae3xx.dts for correct board name.
- Clear and simplify defconfig
- Implement L2C_R_REG/ L2C_W_REG with readl/writel instead of __raw_readl/__raw_writel for endian save
- Remove early_init_dt_add_memory_arch/early_init_dt_alloc_memory_arch to use the generic ones
- Refine devicetree.c
- Fix bug https://lkml.kernel.org/r/1499782590-31366-1-git-send-ema...
- Refine irqchip/irq-ativic32.c implementations
- Add COMPILE_TEST in drivers/net/ethernet/faraday/Kconfig
- Refine cache operations
- Add CONFIG_HW_SUPPORT_UNALIGNMENT_ACCESS
- Fix ZERO_PAGE define
- Remove SA_RESTORER
- Remove uapi/asm/signal.h
- Redefine user_pt_regs
- Remove spinlock.h
- Remove __ARCH_WANT_RENAMEAT and __ARCH_WANT_SYSCALL_OFF_T from unistd.h
- Remove set_fs(USER_DS) because flush_old_exec() will do this setting
- Replace in_atomic() with faulthandler_disabled()
- Add barrier.h
- Select COMMON_CLK
- Add clk_pll in dts
- Add of_clk_init() in arch/nds32/kernel/time.c
Changes in v2:
- Set GENERIC_CALIBRATE_DELAY default n
- Add earlycon support
- Remove earlyprintk
- Add CPU_BIG_ENDIAN, CPU_LITTLE_ENDIAN support
- Refine unalignment access exception handler
- Add VMSPLIT support
- Use only one defconfig
- Change interrupt-cells from 2 to 1
- Refine andestech cpu names in bindings/nds32/cpus.txt
- Get clock frequency in dts because fpga bitmap doesn't include this feature
- Update MAINTAINERS for bindings
- Remove unused configs in Kconfig
- Refine device tree scripts
- Refine coding style
- Use generic ioremap_nocache
- Remove L2CC_PA_BASE define and its codes in head.S. It will be moved to bootloader.
- Set PHYS_OFFSET to 0x0 instead of CONFIG_MEMORY_START
- Remove unused macros
- Simplify cpu_cache_* API
- Change __asm__ __volatile__ to asm volatile
- Refine uaccess.h
- Remove unused/deprecated syscall
- Use generic posix_types.h
- Remove arch_trace_hardirqs_on/arch_trace_hardirqs_off
- Fix bug of restart syscall
- Refine syscall implementations
- Use IS_ENABLED to replace ifdef as possible
- Remove device_initcall(nds32_device_probe)
- Refine vdso implementations
- Refine copy_from_user()/copy_to_user()/clear_user()/get_user()/memmove()/memcpy()
- Refine ioremap.c
- Refine irq-ativic32.c
- Fix a bug of earlycon.c
- Export ioremap_nocache/ioremap_uc/ioremap_wc/ioremap_wt
- Add atcpit100 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=J/YF
-----END PGP SIGNATURE-----
Merge tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 architecture support from Greentime Hu:
"This contains the core nds32 Linux port (including interrupt
controller driver and timer driver), which has been through seven
rounds of review on mailing list.
It is able to boot to shell and passes most LTP-2017 testsuites in
nds32 AE3XX platform:
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78"
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
* tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux: (44 commits)
nds32: To use the generic dump_stack()
nds32: fix building failed if using elf toolchain.
nios2: add ioremap_nocache declaration before include asm-generic/io.h.
nds32: fix building failed if using older version gcc.
dt-bindings: timer: Add andestech atcpit100 timer binding doc
clocksource/drivers/atcpit100: VDSO support
clocksource/drivers/atcpit100: Add andestech atcpit100 timer
net: faraday add nds32 support.
irqchip: Andestech Internal Vector Interrupt Controller driver
dt-bindings: interrupt-controller: Andestech Internal Vector Interrupt Controller
dt-bindings: nds32 SoC Bindings
dt-bindings: nds32 L2 cache controller Bindings
dt-bindings: nds32 CPU Bindings
MAINTAINERS: Add nds32
nds32: Build infrastructure
nds32: defconfig
nds32: Miscellaneous header files
nds32: Device tree support
nds32: Generic timers support
nds32: Loadable modules
...
Current suspend/resume implementation reuses the mvneta_open() and
mvneta_close(), but it could be optimized to take only necessary
actions during suspend/resume.
One obvious problem of current implementation is: after hundreds of
system suspend/resume cycles, the resume of mvneta could fail due to
fragmented dma coherent memory. After this patch, the non-necessary
memory alloc/free is optimized out.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare the suspend/resume improvement in next patch. The
SW parts can be optimized out during resume.
As for rxq handling during suspend, we'd like to drop packets by
calling mvneta_rxq_drop_pkts() which is both SW and HW operation,
so we don't split rxq deinit.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac_dma_tx_ring_free() assigns the ctl1 word which is a litle endian
32-bit word without using proper accessors, fix this, and because a
length cannot be negative, use unsigned int while at it.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the members: base, idm_base and nicpm_base should be annotated with
__iomem since they are pointers to register space. This fixes a bunch of
sparse reported warnings.
Fixes: f6a95a2495 ("net: ethernet: bgmac: Add platform device support")
Fixes: dd5c5d037f ("net: ethernet: bgmac: add NS2 support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-bitbang mentioned 10 for both read and write.
However mdio read opcode is 10 and write opcode is 01
Fixed comment.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 ethernet stops working after system resume from suspend:
[ 582.852065] sky2 0000:04:00.0: Refused to change power state, currently in D3
The current 150ms delay is not enough, change it to 200ms can solve the
issue.
BugLink: https://bugs.launchpad.net/bugs/1758507
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default TX moderation mode was mistakenly set to CQE based. The
intention was to add a control ability in order to improve some specific
use-cases. In general, we prefer to use EQE based moderation as it gives
much better numbers for the common cases.
CQE based causes a degradation in the common case since it resets the
moderation timer on CQE generation. This causes an issue when TSO is
well utilized (large TSO sessions). The timer is set to 16us so traffic
of ~64KB TSO sessions per second would mean timer reset (CQE per TSO
session -> long time between CQEs). In this case we quickly reach the
tcp_limit_output_bytes (256KB by default) and cause a halt in TX traffic.
By setting EQE based moderation we make sure timer would expire after
16us regardless of the packet rate.
This fixes an up to 40% packet rate and up to 23% bandwidth degradtions.
Fixes: 0088cbbc4b ("net/mlx5e: Enable CQE based moderation on TX CQ")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is closed, all the associated irqs are disabled. In the
event that the driver exits a reset in the closed state, we should be
consistent with the state we are in directly after a close. So before we
exit the reset routine, all irqs should be disabled as well. This will
prevent the irqs from being enabled twice in this case and reporting a
number of noisy warning traces.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Iff TSU registers exist on a given [G]Ether controller, they always include
the CAM entry table registers (TSU_ADR{H|L}<n>), thus the check for invalid
TSU_ADRH0 offset in __sh_eth_get_regs() is useless...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6ded286555 ("sh_eth: Fix RX recovery on R-Car in case of RX
ring underrun") added a check for an bad RDFAR offset in sh_eth_rx(), so
that the code could work on the R-Car Ether controllers which don't have
this register (and TDFAR), then the commit 3365711df0 ("sh_eth: WARN on
access to a register not implemented in a particular chip") replaced
offset 0 with 0xffff. Adding/checking the 'no_xdfar' bit field in the
'struct sh_eth_cpu_data' instead results in less object code...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refine the RX check summing handling to propagate the
hardware provided checksum so that we do not have to
compute it later in software.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 145307460b ("devlink: Remove top_hierarchy arg to
devlink_resource_register"), the "top_hierarchy" parameter to
devlink_resource_register() was removed in favor of using the parameter
"parent_resource_id" exclusively to determine who the parent is. The
root node's resource ID for this purpose is
DEVLINK_RESOURCE_ID_PARENT_TOP with the value 0. It is therefore
problematic that the resource MLXSW_SP_RESOURCE_KVD has also ID of 0.
Fix this by numbering driver-specific resources from 1.
Fixes: 145307460b ("devlink: Remove top_hierarchy arg to devlink_resource_register")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass struct mlxsw_core instead of devlink since it is nicer within mlxsw
code and we need both structs in mlxsw_sp_kvdl_resources_register()
anyway.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As struct mlxsw_config_profile is mapped to the payload of the FW
command of the same name, resources_query_enable flag does not belong
there. Move it to struct mlxsw_driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check should be done directly in mlxsw_pci_config_profile, as for
other profile items. Also, be consistent in naming with the rest and
rename to "used_kvd_sizes".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First arg of these helpers should be "mlxsw_core".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should not be part of the struct, as the struct fields
are tightly coupled with the FW command payload of the same name.
Just use the "granularity" define directly, as in other places.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parts info is array. The parts copy this info array, yet they are a
list. So make the indexing according to the id and change the list of
parts into array of parts. This helps to eliminate lookups and
constructs like mlxsw_sp_kvdl_part_update() (took me some non-trivial
time to figure out what is going on there).
Alongside with that, introduce a helper macro to define the parts infos.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_resource_ops should be const as the arg of register function is
also const.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables.
Fixes: 7f47b19bd7 ("mlxsw: spectrum_kvdl: Add support for per part occupancy")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the Inline TLS capability from firmware.
Determine the area reserved for storing the keys
Dump the Inline TLS tx and rx records count.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Reviewed-by: Michael Werner <werner@chelsio.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key area size in hw-config file. CPL struct for TLS request
and response. Work request for Inline TLS.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-31
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add raw BPF tracepoint API in order to have a BPF program type that
can access kernel internal arguments of the tracepoints in their
raw form similar to kprobes based BPF programs. This infrastructure
also adds a new BPF_RAW_TRACEPOINT_OPEN command to BPF syscall which
returns an anon-inode backed fd for the tracepoint object that allows
for automatic detach of the BPF program resp. unregistering of the
tracepoint probe on fd release, from Alexei.
2) Add new BPF cgroup hooks at bind() and connect() entry in order to
allow BPF programs to reject, inspect or modify user space passed
struct sockaddr, and as well a hook at post bind time once the port
has been allocated. They are used in FB's container management engine
for implementing policy, replacing fragile LD_PRELOAD wrapper
intercepting bind() and connect() calls that only works in limited
scenarios like glibc based apps but not for other runtimes in
containerized applications, from Andrey.
3) BPF_F_INGRESS flag support has been added to sockmap programs for
their redirect helper call bringing it in line with cls_bpf based
programs. Support is added for both variants of sockmap programs,
meaning for tx ULP hooks as well as recv skb hooks, from John.
4) Various improvements on BPF side for the nfp driver, besides others
this work adds BPF map update and delete helper call support from
the datapath, JITing of 32 and 64 bit XADD instructions as well as
offload support of bpf_get_prandom_u32() call. Initial implementation
of nfp packet cache has been tackled that optimizes memory access
(see merge commit for further details), from Jakub and Jiong.
5) Removal of struct bpf_verifier_env argument from the print_bpf_insn()
API has been done in order to prepare to use print_bpf_insn() soon
out of perf tool directly. This makes the print_bpf_insn() API more
generic and pushes the env into private data. bpftool is adjusted
as well with the print_bpf_insn() argument removal, from Jiri.
6) Couple of cleanups and prep work for the upcoming BTF (BPF Type
Format). The latter will reuse the current BPF verifier log as
well, thus bpf_verifier_log() is further generalized, from Martin.
7) For bpf_getsockopt() and bpf_setsockopt() helpers, IPv4 IP_TOS read
and write support has been added in similar fashion to existing
IPv6 IPV6_TCLASS socket option we already have, from Nikita.
8) Fixes in recent sockmap scatterlist API usage, which did not use
sg_init_table() for initialization thus triggering a BUG_ON() in
scatterlist API when CONFIG_DEBUG_SG was enabled. This adds and
uses a small helper sg_init_marker() to properly handle the affected
cases, from Prashant.
9) Let the BPF core follow IDR code convention and therefore use the
idr_preload() and idr_preload_end() helpers, which would also help
idr_alloc_cyclic() under GFP_ATOMIC to better succeed under memory
pressure, from Shaohua.
10) Last but not least, a spelling fix in an error message for the
BPF cookie UID helper under BPF sample code, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver needs to re-initailize the IRQ vectors, we make the
new ulp_irq_stop() call to tell the RDMA driver to disable and free
the IRQ vectors. After IRQ vectors have been re-initailized, we
make the ulp_irq_restart() call to tell the RDMA driver that
IRQs can be restarted.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional logic to reserve completion rings for the bnxt_re driver
when it requests MSIX vectors. The function bnxt_cp_rings_in_use()
will return the total number of completion rings used by both drivers
that need to be reserved. If the network interface in up, we will
close and open the NIC to reserve the new set of completion rings and
re-initialize the vectors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor bnxt_need_reserve_rings() slightly so that __bnxt_reserve_rings()
can call it and remove some duplicated code.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add remapping logic so that bnxt_en can use any arbitrary MSIX vectors.
This will allow the driver to reserve one range of MSIX vectors to be
used by both bnxt_en and bnxt_re. bnxt_en can now skip over the MSIX
vectors used by bnxt_re.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, the range of MSIX vectors allocated for the RDMA
driver is disjoint from the network driver. This creates a problem
for the new firmware ring reservation scheme. The new scheme requires
the reserved completion rings/MSIX vectors to be in a contiguous
range.
Change the logic to allocate RDMA MSIX vectors to be contiguous with
the vectors used by bnxt_en on new firmware using the new scheme.
The new function bnxt_get_num_msix() calculates the exact number of
vectors needed by both drivers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver code makes some assumptions about the group index
and the map index of rings. This makes the code more difficult to
understand and less flexible.
Improve it by adding the grp_idx and map_idx fields explicitly to the
bnxt_ring_struct as a union. The grp_idx is initialized for each tx ring
and rx agg ring during init. time. We do the same for the map_idx for
each cmpl ring.
The grp_idx ties the tx ring to the ring group. The map_idx is the
doorbell index of the ring. With this new infrastructure, we can change
the ring index mapping scheme easily in the future.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When firmware sends a DMA response to the driver, the last byte of the
message will be set to 1 to indicate that the whole response is valid.
The driver waits for the message to be valid before reading the message.
The firmware spec allows these response messages to increase in
length by adding new fields to the end of these messages. The
older spec's valid location may become a new field in a newer
spec. To guarantee compatibility, the driver should zero the valid
byte before interpreting the entire message so that any new fields not
implemented by the older spec will be read as zero.
For messages that are forwarded to VFs, we need to set the length
and re-instate the valid bit so the VF will see the valid response.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are created, the current code subtracts the maximum VF
resources from the PF's pool. This under-estimates the resources
remaining in the PF pool. Instead, we should subtract the minimum
VF resources. The VF minimum resources are guaranteed to the VFs
and only these should be subtracted from the PF's pool.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for the maximum pre-set TX channels for ethtool -l, we
need to check the current max_tx_scheduler_inputs parameter from firmware.
This parameter specifies the max input for the internal QoS nodes currently
available to this function. The function's TX rings will be capped by this
parameter. By adding this logic, we provide a more accurate pre-set max
TX channels to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic extended port statistics, if the device is PF and
link is up.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include additional hardware port statistics in ethtool -S, which
are useful for debugging.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VFs are allowed to modify MAC address, even when PF
has assigned one.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear flags when reset command processed successfully for components
specified.
Fixes: 6502ad5963 ("bnxt_en: Add ETH_RESET_AP support")
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RDMA driver is registered, use a new VNIC mode that allows
RDMA traffic to be seen on the netdev in promiscuous mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default ring logic to select default number of rings to be up to
8 per port if the default rings x NIC ports <= total CPUs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor changes, such as new extended port statistics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains updates to mlx5 core and mlx5e netdev drivers.
The main highlight of this series is the RX optimizations for striding RQ path,
introduced by Tariq.
First Four patches are trivial misc cleanups.
- Spelling mistake fix
- Dead code removal
- Warning messages
RX optimizations for striding RQ:
1) RX refactoring, cleanups and micro optimizations
- MTU calculation simplifications, obsoletes some WQEs-to-packets translation
functions and helps delete ~60 LOC.
- Do not busy-wait a pending UMR completion.
- post the new values of UMR WQE inline, instead of using a data pointer.
- use pre-initialized structures to save calculations in datapath.
2) Use linear SKB in Striding RQ "build_skb", (Using linear SKB has many advantages):
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
3) Support XDP over Striding RQ:
Now that linear SKB is supported over Striding RQ,
we can support XDP by setting stride size to PAGE_SIZE
and headroom to XDP_PACKET_HEADROOM.
Striding RQ is capable of a higher packet-rate than
conventional RQ.
Performance testing:
ConnectX-5, 24 rings, default MTU.
CQE compression ON (to reduce completions BW in PCI).
XDP_DROP packet rate:
--------------------------------------------------
| pkt size | XDP rate | 100GbE linerate | pct% |
--------------------------------------------------
| 64byte | 126.2 Mpps | 148.0 Mpps | 85% |
| 128byte | 80.0 Mpps | 84.8 Mpps | 94% |
| 256byte | 42.7 Mpps | 42.7 Mpps | 100% |
| 512byte | 23.4 Mpps | 23.4 Mpps | 100% |
--------------------------------------------------
4) Remove mlx5 page_ref bulking in Striding RQ and use page_ref_inc only when needed.
Without this bulking, we have:
- no atomic ops on WQE allocation or free
- one atomic op per SKB
- In the default MTU configuration (1500, stride size is 2K),
the non-bulking method execute 2 atomic ops as before
- For larger MTUs with stride size of 4K, non-bulking method
executes only a single op.
- For XDP (stride size of 4K, no SKBs), non-bulking have no atomic ops per packet at all.
Performance testing:
ConnectX-5, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Single core packet rate (64 bytes).
Early drop in TC: no degradation.
XDP_DROP:
before: 14,270,188 pps
after: 20,503,603 pps, 43% improvement.
Thanks,
saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJavs5fAAoJEEg/ir3gV/o+iXQIAJQ4jcYb5V3AEPqUeiTNOH2h
e2yyXj2zXNTCl2cekmJriWfQjsA5YizaTNipHb1xR8pznAiIMGmiK5nr8idRY1Qh
M/awuoxJszj8a+z3SxrL/ilgf4HF/89YEt+5MnU/2ihBC3EGG0UbJ6TAC0cXMzmG
Xghi5omlCfsqQQkWooxPVSdRXERLsgzo5kjZ2Zpln/GJa0vVPmIV7ojoQQQzFCMf
eEQzqqEeOk4rk8Z2/5fdsWYjwa2XLnvtUtRBKX/hxCd2zYrFpGUxkzsT/Mikeu+Z
AZAJA4yfHs3dKS3T4CaKDBqhUVxdAsuecT9JlqzgLVEbmw7YypacrPT0TBBsJcI=
=qnbR
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-30
This series contains updates to mlx5 core and mlx5e netdev drivers.
The main highlight of this series is the RX optimizations for striding RQ path,
introduced by Tariq.
First Four patches are trivial misc cleanups.
- Spelling mistake fix
- Dead code removal
- Warning messages
RX optimizations for striding RQ:
1) RX refactoring, cleanups and micro optimizations
- MTU calculation simplifications, obsoletes some WQEs-to-packets translation
functions and helps delete ~60 LOC.
- Do not busy-wait a pending UMR completion.
- post the new values of UMR WQE inline, instead of using a data pointer.
- use pre-initialized structures to save calculations in datapath.
2) Use linear SKB in Striding RQ "build_skb", (Using linear SKB has many advantages):
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
3) Support XDP over Striding RQ:
Now that linear SKB is supported over Striding RQ,
we can support XDP by setting stride size to PAGE_SIZE
and headroom to XDP_PACKET_HEADROOM.
Striding RQ is capable of a higher packet-rate than
conventional RQ.
Performance testing:
ConnectX-5, 24 rings, default MTU.
CQE compression ON (to reduce completions BW in PCI).
XDP_DROP packet rate:
--------------------------------------------------
| pkt size | XDP rate | 100GbE linerate | pct% |
--------------------------------------------------
| 64byte | 126.2 Mpps | 148.0 Mpps | 85% |
| 128byte | 80.0 Mpps | 84.8 Mpps | 94% |
| 256byte | 42.7 Mpps | 42.7 Mpps | 100% |
| 512byte | 23.4 Mpps | 23.4 Mpps | 100% |
--------------------------------------------------
4) Remove mlx5 page_ref bulking in Striding RQ and use page_ref_inc only when needed.
Without this bulking, we have:
- no atomic ops on WQE allocation or free
- one atomic op per SKB
- In the default MTU configuration (1500, stride size is 2K),
the non-bulking method execute 2 atomic ops as before
- For larger MTUs with stride size of 4K, non-bulking method
executes only a single op.
- For XDP (stride size of 4K, no SKBs), non-bulking have no atomic ops per packet at all.
Performance testing:
ConnectX-5, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Single core packet rate (64 bytes).
Early drop in TC: no degradation.
XDP_DROP:
before: 14,270,188 pps
after: 20,503,603 pps, 43% improvement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables, msg and data, have the same value. This patch removes
the extra one.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than use an on-stack array to copy a broadcast address, use
the generic eth_broadcast_addr function to save a trivial amount of
object code.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function calls call_netdevice_notifier(), which also
may take net_rwsem. So, we can't use net_rwsem here.
This patch makes callers of this functions take pernet_ops_rwsem,
like register_netdevice_notifier() does. This will protect
the modifications of net_namespace_list, and allows notifiers
to take it (they won't have to care about context).
Since __rtnl_link_unregister() is used on module load
and unload (which are not frequent operations), this looks
for me better, than make all call_netdevice_notifier()
always executing in "protected net_namespace_list" context.
Also, this fixes the problem we had a deal in 328fbe747a
"Close race between {un, }register_netdevice_notifier and ...",
and guarantees __rtnl_link_unregister() does not skip
exitting net.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for explicit calls of devm_kfree(), as the allocated
memory will be freed during driver's detach.
The driver core clears the driver data to NULL after device_release.
Thus, it is not needed to manually clear the device driver data to NULL.
So remove the unnecessary pci_set_drvdata() and devm_kfree().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change nsim_devlink_setup to return any error back to the caller and
update nsim_init to handle it.
Requested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_rx_mode() is called from atomic context which causes
messages response timeouts while VF to PF communication via MSIx.
To get rid of that we're copy passed mc list, parse flags and queue
handling of kernel request to ordered workqueue.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel calls ndo_set_rx_mode() callback from atomic context which
causes messaging timeouts between VF and PF (as they’re implemented via
MSIx). So in order to handle ndo_set_rx_mode() we need to get rid of it.
This commit implements necessary workqueue related structures to let VF
queue kernel request processing in non-atomic context later.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is to add message handling for ndo_set_rx_mode()
callback at PF side.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel calls ndo_set_rx_mode() callback supplying it will all necessary
info, such as device state flags, multicast mac addresses list and so on.
Since we have only 128 bits to communicate with PF we need to initiate
several requests to PF with small/short operation each based on input data.
So this commit implements following PF messages codes along with new
data structures for them:
NIC_MBOX_MSG_RESET_XCAST to flush all filters configured for this
particular network interface (VF)
NIC_MBOX_MSG_ADD_MCAST to add new MAC address to DMAC filter registers
for this particular network interface (VF)
NIC_MBOX_MSG_SET_XCAST to apply filtering configuration to filter control
register
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ThunderX NIC could be partitioned to up to 128 VFs and thus
represented to system. Each VF is mapped to pair BGX:LMAC, and each of VF
is configured by kernel individually. Eventually the bunch of VFs could be
mapped onto same pair BGX:LMAC and thus could cause several multicast
filtering configuration requests to LMAC with the same MAC addresses.
This commit is to add ThunderX NIC BGX filtering manipulation routines.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ThunderX NIC has two Ethernet Interfaces (BGX) each of them could has
up to four Logical MACs configured. Each of BGX has 32 filters to be
configured for filtering ingress packets. The number of filters available
to particular LMAC is from 8 (if we have four LMACs configured per BGX)
up to 32 (in case of only one LMAC is configured per BGX).
At the same time the NIC could present up to 128 VFs to OS as network
interfaces, each of them kernel will configure with set of MAC addresses
for filtering. So to prevent dupes in BGX filter registers from different
network interfaces it is required to cache and track all filter
configuration requests prior to applying them onto BGX filter registers.
This commit is to update LMAC structures with control fields to
allocate/releasing filters tracking list along with implementing
dmac array allocate/release per LMAC.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ThunderX NIC has set of registers which allows to configure
filter policy for ingress packets. There are three possible regimes
of filtering multicasts, broadcasts and unicasts: accept all, reject all
and accept filter allowed only.
Current implementation has enum with all of them and two generic macro
for enabling filtering et all (CAM_ACCEPT) and enabling/disabling
broadcast packets, which also should be corrected in order to represent
register bits properly. All these values are private for driver and
there is no need to ‘publish’ them via header file.
This commit is to move filtering register manipulation values from
header file into source with explicit assignment of exact register
values to them to be used while register configuring.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Meson8m2 SoC uses a similar (potentially even identical) register
layout as the Meson8b and GXBB SoCs for the dwmac glue.
Add a new compatible string and update the module description to
indicate support for these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon a new UMR post, check if the WQE buffer contains
a previous UMR WQE. If so, modify the dynamic fields
instead of a whole WQE overwrite. This saves a memcpy.
In current setting, after 2 WQ cycles (12 UMR posts),
this will always be the case.
No degradation sensed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
All UMR WQEs of an RQ share many common fields. We use
pre-initialized structures to save calculations in datapath.
One field (xlt_offset) was the only reason we saved a pre-initialized
copy per WQE index.
Here we remove its initialization (move its calculation to datapath),
and reduce the number of copies to one-per-RQ.
A very small datapath calculation is added, it occurs once per a MPWQE
(i.e. once every 256KB), but reduces memory consumption and gives
better cache utilization.
Performance testing:
Tested packet rate, no degradation sensed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When many packets reside on the same page, the bulking of
page_ref modifications reduces the total number of atomic
operations executed.
Besides the necessary 2 operations on page alloc/free, we
have the following extra ops per page:
- one on WQE allocation (bump refcnt to maximum possible),
- zero ops for SKBs,
- one on WQE free,
a constant of two operations in total, no matter how many
packets/SKBs actually populate the page.
Without this bulking, we have:
- no ops on WQE allocation or free,
- one op per SKB,
Comparing the two methods when PAGE_SIZE is 4K:
- As mentioned above, bulking method always executes 2 operations,
not more, but not less.
- In the default MTU configuration (1500, stride size is 2K),
the non-bulking method execute 2 ops as well.
- For larger MTUs with stride size of 4K, non-bulking method
executes only a single op.
- For XDP (stride size of 4K, no SKBs), non-bulking method
executes no ops at all!
Hence, to optimize the flows with linear SKB and XDP over Striding RQ,
we here remove the page_ref bulking method.
Performance testing:
ConnectX-5, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Single core packet rate (64 bytes).
Early drop in TC: no degradation.
XDP_DROP:
before: 14,270,188 pps
after: 20,503,603 pps, 43% improvement.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add XDP support over Striding RQ.
Now that linear SKB is supported over Striding RQ,
we can support XDP by setting stride size to PAGE_SIZE
and headroom to XDP_PACKET_HEADROOM.
Upon a MPWQE free, do not release pages that are being
XDP xmit, they will be released upon completions.
Striding RQ is capable of a higher packet-rate than
conventional RQ.
A performance gain is expected for all cases that had
a HW packet-rate bottleneck. This is the case whenever
using many flows that distribute to many cores.
Performance testing:
ConnectX-5, 24 rings, default MTU.
CQE compression ON (to reduce completions BW in PCI).
XDP_DROP packet rate:
--------------------------------------------------
| pkt size | XDP rate | 100GbE linerate | pct% |
--------------------------------------------------
| 64byte | 126.2 Mpps | 148.0 Mpps | 85% |
| 128byte | 80.0 Mpps | 84.8 Mpps | 94% |
| 256byte | 42.7 Mpps | 42.7 Mpps | 100% |
| 512byte | 23.4 Mpps | 23.4 Mpps | 100% |
--------------------------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make the xdp_xmit indication available for Striding RQ
by taking it out of the type-specific union.
This refactor is a preparation for a downstream patch that
adds XDP support over Striding RQ.
In addition, use a bitmap instead of a boolean for possible
future flags.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.
In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.
To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.
We can satisfy 1 and 2 by configuring:
stride size = MTU + headroom + tailoom.
This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.
Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When modifying the page mapping of a HW memory region
(via a UMR post), post the new values inlined in WQE,
instead of using a data pointer.
This is a micro-optimization, inline UMR WQEs of different
rings scale better in HW.
In addition, this obsoletes a few control flows and helps
delete ~50 LOC.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Do not busy-wait a pending UMR completion. Under high HW load,
busy-waiting a delayed completion would fully utilize the CPU core
and mistakenly indicate a SW bottleneck.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gets the process of a UMR WQE post in one function,
in preparation for a downstream patch that inlines
the WQE data.
No functional change here.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In Striding RQ, each WQE serves multiple packets
(hence called Multi-Packet WQE, MPWQE).
The size of a MPWQE is constant (currently 256KB).
Upon a ringparam set operation, we calculate the number of
MPWQEs per RQ. For this, first it is needed to determine the
number of packets that can reside within a single MPWQE.
In this patch we use the actual MTU size instead of ETH_DATA_LEN
for this calculation.
This implies that a change in MTU might require a change
in Striding RQ ring size.
In addition, this obsoletes some WQEs-to-packets translation
functions and helps delete ~60 LOC.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Knowing the MTU is required for RQ creation flow.
By our design, channels creation flow is totally isolated
from priv/netdev, and can be completed with access to
channels params and mdev.
Adding the MTU to the channels params helps preserving that.
In addition, we save it in RQ to make its access faster in
datapath checks.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With ConnectX-4, we expect the force teardown to fail in case that
DC was enabled, therefore change the message from error to warning.
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
1. This function is not used anywhere in mlx5 driver
2. It has a memcpy statement that makes no sense and produces build
warning with gcc8
drivers/net/ethernet/mellanox/mlx5/core/transobj.c: In function 'mlx5_core_query_xsrq':
drivers/net/ethernet/mellanox/mlx5/core/transobj.c:347:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
Fixes: 01949d0109 ("net/mlx5_core: Enable XRCs and SRQs when using ISSI > 0")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of looking for the EQ of the CQ, remove that redundant code and
use the eq pointer stored in the cq struct.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In mvneta_port_up() we enable relevant RX and TX port queues by write
queues bit map to an appropriate register.
q_map must be ZERO in the beginning of this process.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miguel reported an skb use after free / double free in vrf_finish_output
when neigh_output returns an error. The vrf driver should return after
the call to neigh_output as it takes over the skb on error path as well.
Patch is a simplified version of Miguel's patch which was written for 4.9,
and updated to top of tree.
Fixes: 8f58336d3f ("net: Add ethernet header for pass through VRF device")
Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit has fix for RX traffic issues when we stress test the driver
with continuous ifconfig up/down under very high traffic conditions.
Reason for the issue is that, in existing liquidio_stop function NAPI is
disabled even before actual FW/HW interface is brought down via
send_rx_ctrl_cmd(lio, 0). Between time frame of NAPI disable and actual
interface down in firmware, firmware continuously enqueues rx traffic to
host. When interrupt happens for new packets, host irq handler fails in
scheduling NAPI as the NAPI is already disabled.
After "ifconfig <iface> up", Host re-enables NAPI but cannot schedule it
until it receives another Rx interrupt. Host never receives Rx interrupt as
it never cleared the Rx interrupt it received during interface down
operation. NIC Rx interrupt gets cleared only when Host processes queue and
clears the queue counts. Above anomaly leads to other issues like packet
overflow in FW/HW queues, backpressure.
Fix:
This commit fixes this issue by disabling NAPI only after informing
firmware to stop queueing packets to host via send_rx_ctrl_cmd(lio, 0).
send_rx_ctrl_cmd is not visible in the patch as it is already there in the
code. The DOWN command also waits for any pending packets to be processed
by NAPI so that the deadlock will not occur.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2018-03-29
An update from ieee802154 for *net-next*
Colin fixed a unused variable in the new mcr20a driver.
Harry fixed an unitialised data read in the debugfs interface of the
ca8210 driver.
If there are any issues or you think these are to late for -rc1 (both can also
go into -rc2 as they are simple fixes) let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.10.
The Automotive Safety Pacakge (also called Safety Features) offers us
with error protection in the core by implementing ECC Protection in
memories, on-chip data path parity protection, FSM parity and timeout
protection and Application/CSR interface timeout protection.
In case of an uncorrectable error we call stmmac_global_err() and
reconfigure the whole core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently TX Timeout handler does not behaves as expected and leads to
an unrecoverable state. Rework current implementation of TX Timeout
handling to actually perform a complete reset of the driver state and IP.
We use deferred work to init a task which will be responsible for
resetting the system.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The style of the rx/tx queue's *_coal member assignment is:
static void foo_coal_set(...)
{
set the coal in hw;
update queue's foo_coal member; [1]
}
In other place, we call foo_coal_set(pp, queue->foo_coal), so the above [1]
is duplicated and could be removed.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call of_get_nvmem_mac_address() to fetch the MAC address from an nvmem
cell, if one is provided in the device tree. This allows the address to
be stored in an I2C EEPROM device for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trigger a port mod message to request an MTU change on the NIC when any
physical port representor is assigned a new MTU value. The driver waits
10 msec for an ack that the FW has set the MTU. If no ack is received the
request is rejected and an appropriate warning flagged.
Rather than maintain an MTU queue per repr, one is maintained per app.
Because the MTU ndo is protected by the rtnl lock, there can never be
contention here. Portmod messages from the NIC are also protected by
rtnl so we first check if the portmod is an ack and, if so, handle outside
rtnl and the cmsg work queue.
Acks are detected by the marking of a bit in a portmod response. They are
then verfied by checking the port number and MTU value expected by the
app. If the expected MTU is 0 then no acks are currently expected.
Also, ensure that the packet headroom reserved by the flower firmware is
considered when accepting an MTU change on any repr.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the 'change_mtu' app callback to 'check_mtu'. This is called
whenever an MTU change is requested on a netdev. It can reject the
change but is not responsible for implementing it.
Introduce a new 'repr_change_mtu' app callback that is hit when the MTU
of a repr is to be changed. This is responsible for performing the MTU
change and verifying it.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per interrupt
until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had previously
determined instead of the user requested parameters
Fixes: 9f4ca05827 ("net: bcmgenet: Add support for adaptive RX coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per
interrupt until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had
previously determined instead of the user requested parameters
Fixes: b6e0e87542 ("net: systemport: Implement adaptive interrupt coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive TX coalescing is not currently giving us any advantages and
ends up making the CPU spin more frequently until TX completion. Deny
and disable adaptive TX coalescing for now and rely on static
configuration, we can always add it back later.
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the hash filter init error
handling case instead of 0, as done elsewhere in this function.
Fixes: 5c31254e35 ("cxgb4: initialize hash-filter configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkman says:
====================
pull-request: bpf 2018-03-29
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix nfp to properly check max insn count while emitting
instructions in the JIT which was wrongly comparing bytes
against number of instructions before, from Jakub.
2) Fix for bpftool to avoid usage of hex numbers in JSON
output since JSON doesn't accept hex numbers with 0x
prefix, also from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Smaller new features to various drivers but nothing really out of
ordinary.
Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
iwlwifi
* support for new PCI IDs for the 9000 family
* support for a new firmware API version
* support for advanced dwell and Optimized Connectivity Experience
(OCE) in scanning
btrsi
* fix kconfig dependencies
wil6210
* support multiple virtual interfaces
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJavOUVAAoJEG4XJFUm622bf2cH/i/we50/PR64rxq5RV8HWQPt
9P/bn4I1pEDRDJZw00f/bqe20w5ps1UuHs1hgOiJzOsZNfxVv+B17MMY/dN/+5Ob
hBYeZQFZ0MJ1cEF6J6gzebH1BKVEApVPI49MmAUzdtATO/6YgCnxovb61bl51RYg
vtMNcrXBQDplPTh5W7YHXrUz4sV1d3daCk/6Coea+SoF6eL1tn+qndo6GhNIMboE
HA0vV27Wf2RCzlxcQ4WGD4cre6n9sRaX4lcFzMEtbM7ziM0E0SES7eEThB5ST+A6
3K0+zSuyEfOu40QRJF1g9Wl8FXvp+9SRVC7s1rXjDYUv9sGl+a5fhb7VPgrYn/g=
=AgFb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
Smaller new features to various drivers but nothing really out of
ordinary.
Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
iwlwifi
* support for new PCI IDs for the 9000 family
* support for a new firmware API version
* support for advanced dwell and Optimized Connectivity Experience
(OCE) in scanning
btrsi
* fix kconfig dependencies
wil6210
* support multiple virtual interfaces
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlq85QQACgkQB8qZga/f
l8Sdbg//bc8C/4F1TUdJqZWGK1j9Lwd6nZpP0iFqH5Ees3MMnti5XdV2dCL31ivz
c8DOuRAU8ZG/RLPgSTHVZHwh+f7S5/TxSKg8WOBvrYk7a0C1uvVVhe5XZQEmqE7g
eqM0+UQ5DyzUYnu0kSUrFKPV7BqDa2YzVDdK8e8iozqZmAnvGN9k8H7EDEeUxtxk
LEl+bEcmhDSfIssU2Iaksl+9qoZP6BkoVGAOmDzIL654WV4XVKorxRX6vndqSQGu
0cCz2Occ+/0hfvszONBRR4M/gtI/Yyn3u+D1Q0YD3X40Q9gJE11fcodmMT61l5C7
rGcu94RIGilvRvjZScK3giiU2L7DD+VETUa+YGnjd8gLpmrYd6cURxlm4yuHbw8C
UScLCApAUuY+skmPLeuyHW9mnzHaC336vzVjk8OhdNRhX23/rB8nk1yIywgqETVW
g/iub8/Xp6TRfdyh76I18wlfqCp1It2JAeICgKH5NPlwUA6U0xFR0/ddSR8FuAcK
ZLY8mgsc2kIH6r4x5sjeH+Yb6tGi/Z3HMZM2hna+t4vSpn6Q5+GPsA6yuHuBUhJb
8QswMiLDSux8I4guKgQyROiHaCzE3zOigJ4o1z9XITKsgluZVxnKr+ETKdr88WFp
II8U0qH/kejXIfxUjbv5Wla70J9wi/hjxR6vOfSkEtYNvIApdfc=
=hI0F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a fair number of patches, but many of them are from the
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
VTU miss violations can happen under normal conditions. Don't spam the
kernel log, downgrade the output to debug level only. The statistics
counter will indicate it is happening, if anybody not debugging is
interested.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the numbers of various ATU and VTU violation statistics and
return them as part of the ethtool -S statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1351:16: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, driver drops received packets which are indicated as
invalid checksum by the device. Instead of dropping such packets,
pass them to the stack with CHECKSUM_NONE indication in skb.
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cotsworks modules fail the checksums - it appears that Cotsworks
reprograms the EEPROM at the end of production with the final product
information (serial, date code, and exact part number for module
options) and fails to update the checksum.
Work around this by detecting the Cotsworks name in the manufacturer
field, and reducing the checksum failures to warnings rather than a
hard error.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ethtool callback implementation for flash update.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds APIs for flash access.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for populating the flash image attributes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features
RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support
RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During heavy tx traffic, control messages (sent by liquidio driver to NIC
firmware) sometimes do not get processed in a timely manner. Reason is:
the low-level metadata of control messages and that of egress network
packets indicate that they have the same priority.
Fix it by setting a higher priority for control messages through the new
ctrl_qpg field in the oct_txpciq struct. It is the NIC firmware that does
the actual setting of priority by writing to the new ctrl_qpg field; the
host driver treats that value as opaque and just assigns it to pki_ih3->qpg
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink support to netdevsim and use it to implement a simple,
profile based resource controller. Only one controller is needed
per namespace, so the first netdevsim netdevice in a namespace
registers with devlink. If that device is deleted, the resource
settings are deleted.
The resource controller allows a user to limit the number of IPv4 and
IPv6 FIB entries and FIB rules. The resource paths are:
/IPv4
/IPv4/fib
/IPv4/fib-rules
/IPv6
/IPv6/fib
/IPv6/fib-rules
The IPv4 and IPv6 top level resources are unlimited in size and can not
be changed. From there, the number of FIB entries and FIB rule entries
are unlimited by default. A user can specify a limit for the fib and
fib-rules resources:
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 96
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib-rules size 16
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib size 64
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib-rules size 16
$ devlink dev reload netdevsim/netdevsim0
such that the number of rules or routes is limited (96 ipv4 routes in the
example above):
$ for n in $(seq 1 32); do ip ro add 10.99.$n.0/24 dev eth1; done
Error: netdevsim: Exceeded number of supported fib entries.
$ devlink resource show netdevsim/netdevsim0
netdevsim/netdevsim0:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables non
resources:
name fib size 96 occ 96 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables
...
With this template in place for resource management, it is fairly trivial
to extend and shows one way to implement a simple counter based resource
controller typical of network profiles.
Currently, devlink only supports initial namespace. Code is in place to
adapt netdevsim to a per namespace controller once the network namespace
issues are resolved.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauuK/AAoJEEg/ir3gV/o+Ro4IAIBcQl4S/6jPttGDOPwElU4b
Q8MuQbnB9k36Kf6x3GrhBqwtoS3OYBLvfyOeZsghD8uyzklhnqR/psrCt1YhLXq7
aI5iFbuQucCUwIYBscuZegXBs+PTJYALoil05hOwSkwhEBZR53ZvdRQ9Jg0G0QiY
sYEYAl41A1DWQOLET5lwleUpVQnVnNvIcXqNHKBKbS4f8rmLpfsZ6YAxJiiIjeDJ
gLbsaxUyY3p77594okBk6DuFBWZsEAKwumspdSc92OEMrZSYE5ugNL+UgVEE7I8F
JgK/4OUarw3K7xwhAg//ZhTM1iRRdJv0Sz2GPhhWRzYB0jWACc3ZG2/M/WmxFIg=
=Uslu
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-27 (Misc updates & SQ recovery)
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can have interrupts left enabled form e.g: the bootloader which used
the network device for network boot. Make sure we have those disabled as
early as possible to avoid spurious interrupts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system contains several BGMAC adapters, it is nice to be able
to tell which one is which by looking at /proc/interrupts. Use the
network device name as a name to request_irq() with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the National Instruments XGE 1/10G network device.
It uses the EEPROM on the board via NVMEM.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent change to netvsc drive in how receive flags are handled
broke multicast. The Hyper-v/Azure virtual interface there is not a
multicast filter list, filtering is only all or none. The driver must
enable all multicast if any multicast address is present.
Fixes: 009f766ca2 ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.
Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.
Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ca8210_test_int_user_write() a user can request the transfer of a
frame with a length field (command.length) that is longer than the
actual buffer provided (len). In this scenario the driver will copy
the buffer contents into the uninitialised command[] buffer, then
transfer <data.length> bytes over the SPI even though only <len> bytes
had been populated, potentially leaking sensitive kernel memory.
Also the first 6 bytes of the command buffer must be initialised in case
a malformed, short packet is written and the uninitialised bytes are
read in ca8210_test_check_upstream.
Reported-by: Domen Puncer Kugler <domen.puncer@samsung.com>
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Tested-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
ath.git patches for 4.17. Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
Remove the static array and use the generic routine to set the
Ethernet broadcast address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().
This will fix below warning,
WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
invalid rate bw=1, mcs=9, nss=2
(unwind_backtrace) from
(cfg80211_calculate_bitrate+0x174/0x220)
(cfg80211_calculate_bitrate) from
(nl80211_put_sta_rate+0x44/0x1dc)from
(nl80211_put_sta_rate) from
(nl80211_send_station+0x388/0xaf0)
(nl80211_get_station+0xa8/0xec)
[ end trace da8257d6a850e91a ]
Fixes: 842be75c77 ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes regression caused by 0c317a02ca
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.
Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.
Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.
Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware of QCA6174/QCA9377 already support the feature, just enable
it to be able to handle the get_temperature command and process the event.
You can read the temperature by using the hwmon interface,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Verified with the following hardware and software combination,
QCA6174, only firmware-4.bin doesn't support this, otherwise all support.
QCA9377, all the firmwares upstreamed support this command
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
some userspace programs (e.g. hostapd) need to set the regulatory domain
before selecting the operating channel. Synchronize DFS detector regardless of
the value of ah->curchan, to avoid situations where wireless scan can't be done
on some 5GHz sub-bands, because dfs_region is constantly UNSET.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Timothy Redaelli <tredaelli@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When FW responds with a message of wrong size or type make sure
the type is checked first and included in the wrong size message.
This makes it easier to figure out which FW command failed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
NFP has a prng register, which we can read to obtain a u32 worth
of pseudo random data. Generate code for it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow atomic add to be used even when the value is not guaranteed
to fit into a 16 bit immediate. This requires the value to be pulled
as data, and therefore use of a transfer register and a context swap.
Track the information about possible lengths of the value, if it's
guaranteed to be larger than 16bits don't generate the code for the
optimized case at all.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow callers to control the delay slots of commands, instead of
giving them just a wait/nowait choice.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement atomic add operation for 32 and 64 bit values. Depend
on the verifier to ensure alignment. Values have to be kept in
big endian and swapped upon read/write. For now only support
atomic add of a constant.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Support calling map_delete_elem() FW helper from the datapath
programs. For JIT checks and code are basically equivalent
to map lookups. Similarly to other map helper key must be on
the stack. Different pointer types are left for future extension.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Support calling map_update_elem() from the datapath programs
by calling into FW-provided helper. Value pointer is passed
in LM pointer #2. Keeping track of old state for arg3 is not
necessary, since LM pointer #2 will be always loaded in this
case, the trivial optimization for value at the bottom of the
stack can't be done here.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a verifier helper for performing the basic state checks
before a call to a map helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Our implementation has restriction on stack pointers for function
calls. Move the common checks into a helper for reuse. The state
has to be encapsulated into a structure to support parameters
other than BPF_REG_2.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We will reuse most of map call code gen for other map calls.
Rename the lookup gen function and use meta->func_id instead
of hard-coding lookup.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch is the front end of this optimisation, it detects and marks
those packet reads that could be cached. Then the optimisation "backend"
will be activated automatically.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch add the support for unaligned read offset, i.e. the read offset
to the start of packet cache area is not aligned to REG_WIDTH. In this
case, the read area might across maximum three transfer-in registers.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch assumes there is a packet data cache, and would try to read
packet data from the cache instead of from memory.
This patch only implements the optimisation "backend", it doesn't build
the packet data cache, so this optimisation is not enabled.
This patch has only enabled aligned packet data read, i.e. when the read
offset to the start of cache is REG_WIDTH aligned.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
fix iwlwifi_dev_ucode_error tracepoint to pass pointer to a table
instead of all 17 arguments by value.
dvm/main.c and mvm/utils.c have 'struct iwl_error_event_table'
defined with very similar yet subtly different fields and offsets.
tracepoint is still common and using definition of 'struct iwl_error_event_table'
from dvm/commands.h while copying fields.
Long term this tracepoint probably should be split into two.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
two trace events defined with the same name and both unused.
They conflict in allyesconfig build. Rename one of them.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We can set triggers that cause a debug data collection when something
of interest happens (e.g. when too many probes are lost conscutively).
Normally, this triggers don't cause the FW to be restarted, but in
some cases that may be desired, so we recover from the problem. To
support this, add a flag that indicates that the FW should be
restarted when the trigger fires.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have a boolean variable for each cause.
This costs space, and requires to check each separately
when determining low latency.
Since we have another cause incoming, convert it to an enum.
While at it, move the retrieval of the prev value and the
assignment of the new value to be inside iwl_mvm_update_low_latency
and save the need for each caller to do it separately.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some geographic profiles require specific handling. For example ETSI
profile requires special channel access handling. Add geographic
profile information to MCC_UPDATE response to allow it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A lot of new PCI IDs were added for the 9000 series. Add them to the
list of supported PCI IDs.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove fragmented_dwell_time and add num_of_fragments to support
the new API version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW does not allocate quota air time for the binding of a station
MAC before iwlmvm indicates that it is associated. Currently iwlmvm
indicates that the MAC is associated only after hearing a beacon from
the AP. In case a deauthentication frame is sent before the MAC is
associated, the frame might not be sent as the corresponding binding
is not scheduled.
To handle such cases, set IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP in the
HW flags, requesting mac80211 to call the mgd_prepare_tx() callback
before transmitting a deauthentication frame if associated but no
beacon was heard from the AP.
In addition, do not warn in iwl_mvm_mac_mgd_prepare_tx() when already
associated as now the callback can be called also when associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for Optimized Connectivity Experience (OCE). Get
capabilities from the fw, expose them with nl80211, and enable them in
UMAC scan if the relevant nl80211 flags are set by the userspace.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the scan command API with support for adaptive dwell. Adaptive
dwell is a type of scan that dynamically changes the time it remains
on each channel listening for beacons or probe responses.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes iwl_mvm_disable_txq() may be called with mac80211_queue ==
IEEE80211_INVAL_HW_QUEUE, and this would cause us to use BIT(0xFF)
which is way too large for the u16 we used to store it in
hw_queue_to_mac820211. If this happens the following UBSAN warning
will be generated:
[ 167.185167] UBSAN: Undefined behaviour in drivers/net/wireless/intel/iwlwifi/mvm/utils.c:838:5
[ 167.185171] shift exponent 255 is too large for 64-bit type 'long unsigned int'
Fix that by checking that it is not IEEE80211_INVAL_HW_QUEUE and,
while at it, add a warning if the queue number is larger than
IEEE80211_MAX_QUEUES.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case debug configuration is started with LDBG cmd also start timestamp
marker for syncing logs witn the FW.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes future bail-outs from transmitting an AMSDU more
readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
An error TX completion (CQE) which arrived on a specific SQ indicates
that this SQ got moved by the hardware to error state, which means all
pending and incoming TX requests are dropped or will be dropped and no
further "Good" CQEs will be generated for that SQ.
Before this patch TX completions (CQEs) were not monitored and were
handled as a regular CQE. This caused the SQ to stay in an error state,
making it useless for xmiting new packets.
Mitigation plan:
In case of an error completion, schedule a recovery work which would do
the following:
- Mark the TXQ as DRV_XOFF to disable new packets to arrive from the
stack
- NAPI to flush all pending SQ WQEs (via flush_in_error_en bit) to
release SW and HW resources(SKB, DMA, etc) and have the SQ and CQ
consumer/producer indices synced.
- Modify the SQ state ERR -> RST -> RDY (restart the SQ).
- Reactivate the SQ and reset SQ cc and pc
If we identify two consecutive requests for SQ recover in less than
500 msecs, drop the recover request to avoid CPU overload, as this
scenario most likely happened due to a severe repeated bug.
In addition, add SQ recover SW counter to monitor successful recoveries.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Monitor and dump xmit error completions. In addition, add err_cqe
counter to track the number of error completion per send queue.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move query SQ state function from mlx5_ib to mlx5_core in order to
have it in shared code.
It will be used in a downstream patch from mlx5e.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver callback for handling TX timeout should access some internal
resources (SQ, CQ) in order to decide if the tx timeout work should be
scheduled. These resources might be unavailable if channels are closed
in parallel (ifdown for example).
The state lock is the mechanism to protect from such races.
Move all TX timeout logic to be in the work under a state lock.
In addition, Move the work from the global WQ to mlx5e WQ to make sure
this work is flushed when device is detached..
Also, move the mlx5e_tx_timeout_work code to be next to the TX timeout
NDO for better code locality.
Fixes: 3947ca1859 ("net/mlx5e: Implement ndo_tx_timeout callback")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commit 58d522912a ("net/mlx5e: Support TX packet copy into WQE")
introduced the max inline WQE as an ethtool tunable. One commit later,
that functionality was made dependent on BlueFlame.
Commit 6982ab6097 ("net/mlx5e: Xmit, no write combining") removed
BlueFlame support, and with it the max inline WQE.
This patch cleans up the leftovers from the removed feature.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a control private flag in ethtool to enable/disable
Striding RQ feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Do not implicit a call to mlx5e_init_rq_type_params() upon every
change in RQ type. It should be called only on channels creation.
Fixes: 2fc4bfb725 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It can be derived from other params, calculate it
via the dedicated function when needed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce functions to calculate them when needed.
They can be derived from other params.
This will simplify transition between RQ configurations.
In general, any parameter that is not explicitly set
or controlled, but derived from other parameters,
should not have a control-path field itself, but a
getter function.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In copying skb header to skb->data, replace the call to
skb_copy_to_linear_data_offset() with a zero offset with
the call to the no-offset function skb_copy_to_linear_data().
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pass the base dma address and offset to dma_sync_single_range_for_cpu(),
instead of doing the pre-calculation.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clean it up as it's not in use.
Fixes: d9d9f156f3 ("net/mlx5e: Expand WQE stride when CQE compression is enabled")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We turn the feature off for servers with PCI BW bounded
by a threshold (16G) and lower than MAX LINK BW.
This improves the effectiveness of CQE compression feature,
that is defaulted to ON for the same case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Get the link/pci speed query and logic into a single function.
Unify the heuristics and use a single PCI threshold (16G) for all.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FLOW_RSS flag was causing us to insert UDP filters when TCP was wanted.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise races are possible between ethtool ops and
efx_ef10_rx_restore_rss_contexts().
Also, don't try to perform the restore on every reset, only after an MC
reboot, otherwise we'll leak RSS contexts on the NIC.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some other operation gets the MCDI lock ahead of us and performs an MC
reboot, then our attempt to insert the filter will fail with EINVAL,
because the destination VI (spec->dmaq_id, MC_CMD_FILTER_OP_IN_RX_QUEUE) does
not exist. But the caller's request (which might e.g. be an ethtool ntuple
request from userland) isn't invalid, it just got unlucky; so return EAGAIN.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this change, the spinlock efx->filter_lock is no longer used and is
thus removed.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx->filter_lock remains in place for use on farch, but EF10 now ignores it.
EFX_EF10_FILTER_FLAG_BUSY is no longer needed, hence it is removed.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having an efx->type->filter_rfs_insert() method, just use
workitems with a worker function that calls efx->type->filter_insert().
The only user of this is efx_filter_rfs(), which now queues a call to
efx_filter_rfs_work().
Similarly, efx_filter_rfs_expire() is now a worker function called on a
new channel->filter_work work_struct, so the method
efx->type->filter_rfs_expire_one() is no longer called in atomic context.
We also add a new mutex efx->rps_mutex to protect the RPS state (efx->
rps_expire_channel, efx->rps_expire_index, and channel->rps_flow_id) so
that the taking of efx->filter_lock can be moved to
efx->type->filter_rfs_expire_one().
Thus, all filter table functions are now called in a sleepable context,
allowing them to use sleeping locks in a future patch.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use relaxed I/O on the hot path. This achieves significant performance
improvements. On a 10G link, this makes a basic iperf TCP test go from
an average of 4.5 Gbits/sec to about 9.40 Gbits/sec.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message, cosmetic changes]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c5ad119fb6
("net: sched: pfifo_fast use skb_array") driver is exposed
to an issue where it is hitting NULL skbs while handling TX
completions. Driver uses mmiowb() to flush the writes to the
doorbell bar which is a write-combined bar, however on x86
mmiowb() does not flush the write combined buffer.
This patch fixes this problem by replacing mmiowb() with wmb()
after the write combined doorbell write so that writes are
flushed and synchronized from more than one processor.
V1->V2:
-------
This patch was marked as "superseded" in patchwork.
(Not really sure for what reason).Resending it as v2.
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_delete_all_resources_for_slave in resource tracker should free all
memory allocated for a slave.
While releasing memory of fs_rule, it misses releasing memory of
fs_rule->mirr_mbox.
Fixes: 78efed2751 ('net/mlx4_core: Support mirroring VF DMFS rules on both ports')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global pause and PFC configuration should be mutually exclusive (i.e. only
one of them at most can be set). However, once PFC was turned off,
driver automatically turned Global pause on. This is a bug.
Fix the driver behaviour to turn off PFC/Global once the user turned the
other on.
This also fixed a weird behaviour that at a current time, the profile
had both PFC and global pause configuration turned on, which is
Hardware-wise impossible and caused returning false positive indication
to query tools.
In addition, fix error code when setting global pause or PFC to change
metadata only upon successful change.
Also, removed useless debug print.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauV9vAAoJEEg/ir3gV/o+Dw4H/0oT5mXUQuEdXDw3y3JtodMA
VEYjPt7EH+X0RUZcO9xkiZGwtfh5+Bk7oDB4uy5IzGdAAEgCX5VvR+m3jnbRfORm
WztMGAy1fiswavYf5tYDBjSM0HSLLKxCUJr0FcPG5DG5Fe90n0DvP2Xj0l+6R0Og
7SSwiK2UXrnfcAvDTFUgj0k2IEAUH1/dCwfruVvt4H4R1Pp6PQGBEfuEc3Jra4wi
9wYik10xQ/MTVxEtw3Om+D7CJzvSiz6DOk2Pp0Ls+1RKvKrlqWyiAOR7nswHRgIk
hnqNV3t47FP1W4bp1YpMjeQ0yi2xcJQPBzRdaf22MDaUiEBLFQBqiINPsOaniL0=
=Tqzl
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-03-23
The following series includes fixes for mlx5 netdev and eswitch.
v1->v2:
- Fixed commit message quotation marks in patch #7
For -stable v4.12
('net/mlx5e: Avoid using the ipv6 stub in the TC offload neigh update path')
('net/mlx5e: Fix traffic being dropped on VF representor')
For -stable v4.13
('net/mlx5e: Fix memory usage issues in offloading TC flows')
('net/mlx5e: Verify coalescing parameters in range')
For -stable v4.14
('net/mlx5e: Don't override vport admin link state in switchdev mode')
For -stable v4.15
('108b2b6d5c02 net/mlx5e: Sync netdev vxlan ports at open')
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes misc updates for mlx5 core and netdev dirver,
Highlights:
From Inbar, three patches to add support for PFC stall prevention
statistics and enable/disable through new ethtool tunable, as requested
from previous submission.
From Moshe, four patches, added more drop counters:
- drop counter for netdev steering miss
- drop counter for when VF logical link is down
- drop counter for when netdev logical link is down.
From Or, three patches to support vlan push/pop offload via tc HW action,
for newer HW (Connectx-5 and onward) via HW steering flow actions rather
than the emulated path for the older HW brands.
And five more misc small trivial patches.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauVxkAAoJEEg/ir3gV/o+Oi4H/1Mzv+XEuHLwVJHpzMNVLVeR
EK1GDW3724zjY24Iy+9FRppL1mV0hY3aw1qhD+rUmUKQx+Q3OBrH1WN2QJkjBkM9
i60ygFLTHvcHyPFmHtPzCckO7ODdWsXSlEwsl8kCSITQTn1Mjf6v7Mogd0CLCbwN
iu8ocpHTD+/whE5gq9aDDrGtuzgJbPiRqavvsof9pc2g1JlnvtHs9xoiN+vzoqIa
9lGS+2UM2+wFw9rMtbdaqtfVPsupMeEdGZ98chn0gpWshOvOda5NuRE59M+5un5E
C3nJ4Js//PLkvQ9Nu7+goXtbfPLCxvcuurid5TM2Su9hmD+9Us223TcAvdpOMoY=
=VdCO
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-22 (Misc updates)
This series includes misc updates for mlx5 core and netdev dirver,
Highlights:
From Inbar, three patches to add support for PFC stall prevention
statistics and enable/disable through new ethtool tunable, as requested
from previous submission.
From Moshe, four patches, added more drop counters:
- drop counter for netdev steering miss
- drop counter for when VF logical link is down
- drop counter for when netdev logical link is down.
From Or, three patches to support vlan push/pop offload via tc HW action,
for newer HW (Connectx-5 and onward) via HW steering flow actions rather
than the emulated path for the older HW brands.
And five more misc small trivial patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi is checking Tx queue status and waking the Tx queue if required.
Same operation is being done while freeing every Tx buffer.
So removed the duplicate operation of checking Tx queue status from the Tx
buffer free functions.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_drvdata() is called only after registering the net_device,
therefore we could run into a NPE if one of the functions using
driver_data is called before it's set.
Fix this by calling pci_set_drvdata() before registering the
net_device.
This fix is a candidate for stable. As far as I can see the
bug has been there in kernel version 3.2 already, therefore
I can't provide a reference which commit is fixed by it.
The fix may need small adjustments per kernel version because
due to other changes the label which is jumped to if
register_netdev() fails has changed over time.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:508:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helper functions that search for given entries in the TCAM filter
on PPv2 controller make use of dynamically alloced temporary variables,
allocated with GFP_KERNEL. These functions can be called in atomic
context, and dynamic alloc is not really needed in these cases anyways.
This commit gets rid of dynamic allocs and use stack allocation in the
following functions, and where they're used :
- mvpp2_prs_flow_find
- mvpp2_prs_vlan_find
- mvpp2_prs_double_vlan_find
- mvpp2_prs_mac_da_range_find
For all these functions, instead of returning an temporary object
representing the TCAM entry, we simply return the TCAM id that matches
the requested entry.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_hw_read function uses the 'index' field of the struct
mvpp2_prs_entry to initialize the rest of the fields. This makes it
unclear from a caller's perspective, who needs to manipulate a struct
that is not entirely initialized.
This commit makes it an init function for prs_entry, by passing it the
index as a parameter. The function now zeroes the entry, and sets the
index field before doing all other init from HW.
The function is renamed 'mvpp2_prs_init_from_hw' to make that clear.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-03-26
This series contains updates to i40e only.
Jake provides several patches which remove the need for cmpxchg64(),
starting with moving I40E_FLAG_[UDP]_FILTER_SYNC from pf->flags to pf->state
since they are modified during run time possibly when the RTNL lock is not
held so they should be a state bits and not flags. Moved additional
"flags" which should be state fields, into pf->state. Ensure we hold
the RTNL lock for the entire sequence of preparing for reset and when
resuming, which will protect the flags related to interrupt scheme under
RTNL lock so that their modification is properly threaded. Finally,
cleanup the use of cmpxchg64() since it is no longer needed. Cleaned up
the holes in the feature flags created my moving some flags to the state
field.
Björn Töpel adds XDP_REDIRECT support as well as tweaking the page
counting for XDP_REDIRECT so that it will function properly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a theoretical NULL pointer dereferencing in mt76x2_tx routine that
can occurs for injected frames in a monitor vif since vif pointer could
be NULL for that interfaces
Fixes: 2340523646 ("mt76: fix transmission of encrypted mgmt frames")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use mt76_poll_msec() in mt76pci_load_firmware to check if the firmware
has been started instead of explicitly poll MCU running register
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcms_ucode_init_buf() duplicates the ucode chunks via kmemdup()
with GFP_ATOMIC as a precondition of wl->lock acquired. This caused
allocation failures sometimes as reported in the bugzilla below.
When looking at the the real usage, one can find that it's called
solely from brcms_request_fw(), and it's obviously outside the lock.
Hence we can use GFP_KERNEL there safely for avoiding such allocation
errors.
Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=1085174
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This field did not have kerneldoc description so adding it now.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function was pretty minimal and now it is called only from one
place so just get rid of it.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function is no longer used so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This changes the bus layer api by having the caller provide an
extension. With this the callback can use brcmf_fw_alloc_request()
to get the needed firmware name.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_fw_alloc_request() takes a list of required files
and allocated the struct brcmf_fw_request instance accordingly. The
request can be modified by the caller before being passed to the
brcmf_fw_request_firmwares() function.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the function brcmf_fw_get_firmwares() a bit more easy to extend
using a structure to pass the request parameters.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of defining individual filenames for firmware and nvram
use a basename and derive the names from that.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver used to create a brcmfmac dir entry at the top level
debugfs mount point. This moves the debugfs entries into the
wiphy debugfs dir entry.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework the driver so the wiphy instance holds the main driver information
in its private buffer. Previously it held struct brcmf_cfg80211_info
instance so a bit of reorg was needed. This was done so that the wiphy
name or its parent device can be shown in debug output.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When logging the chip id/revision information make use of
brcmf_chip_name() so it is always the same.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The chip id can either be four or five digits. For the chip name either
the hexadecimal value needs to be taken (four digits) or the decimal
value (five digits). The function brcmf_chip_name() does this conversion
so use it to store the name in driver revision info.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of a linux error brcmf_fil_cmd_data() blurts an error message
in which the error code is translated to an error string. However, it
maps it to a firmware error string which should not happen. Simply
print only the numeric error code and be done with it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in RT_TRACE message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net?
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct comment. Set bit 3 and bit 4 of 0x0005 register (REG_APS_FSMCO + 1)
to 0 which means disable WL suspend, not enable WL suspend.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex support multiple platforms, but this drivers doesn't support full
functions yet, so this commit adds dummy definitions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New constant and variables definitions are used by btcoex of 8822b, so
this commit add them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In connection notify v1, btcoex only need to know start/end association,
and it will discriminate 2G and 5G band in v2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Normal LPS is decomposed into pre- and post- parts, so we can issue H2C
with TDMA parameters in the "critical section" that dirver can't change
LPS state at the moment.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get phydm's counter and version from the module phydm that is not
submitted so we implement dummy functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The btcoex use the rate to rsolve IOT issue that some APs reduce TX
rate quickly, so it uses the RX rate as a clue to decide TDMA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger#lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex does different decision according to MCC or SCC status, but
driver is still SCC currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add customer_id field in structure, and then this is a clue to implement
the behavior defined by vendor LENOVO_CHINA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex uses dm's counters to check the environment is noisy or not. If it
is clean, btcoex set more time slots to WiFi so that it can transmit as
soon as possible. That will save time, and BT will have more time slots
after WiFi traffic is complete.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports "rtl_is_special_data() warn: inconsistent indenting", but
it is an obvious redundant statement so remove it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sparse reports some functions were not declared, so add 'static' as
modifier. Remove an unused function btc8821a1ant_is_wifi_status_changed()
exposed due to 'static'.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable buffer_size is re-assigned the same value, this duplicated
assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/rsi/rsi_91x_usb.c:140:4: warning: Value stored
to 'buffer_size' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently rsi code uses a VLA based on a function argument to
`rsi_sdio_load_data_master_write()`. The function call chain is
Both these functions
rsi_sdio_reinit_device()
rsi_probe()
start the call chain:
rsi_hal_device_init()
rsi_load_fw()
auto_fw_upgrade()
ping_pong_write()
rsi_sdio_load_data_master_write()
[Without familiarity with the code] it appears that none of the 4 locks
mutex
rx_mutex
tx_mutex
tx_bus_mutex
are held when `rsi_sdio_load_data_master_write()` is called. It is therefore
safe to use kmalloc with GFP_KERNEL.
We can avoid using the VLA by using `kmalloc()` and free'ing the memory on all
exit paths.
Change buffer from 'u8 array' to 'u8 *'. Call `kmalloc()` to allocate memory for
the buffer. Using goto statement to call `kfree()` on all return paths.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc()` however this code is only called on initialization
(and re-initialization) so this overhead should not degrade performance.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the following sparse warning in mwifiex_cmd_append_11n_tlv:
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: right side has type int
Fixes: 77423fa739 ("mwifiex: fix incorrect ht capability problem")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes spelling typos found in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
