This patch prevents driver from setting lower default speed of 1 GB/sec,
if the switch does not support Get Port Speed Capabilities (GPSC)
command. Setting this default speed results into much lower write
performance for large sequential WRITE. This patch modifies driver to
check for gpsc_supported flags and prevents driver from issuing
MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver
does not send this mailbox command, firmware assumes maximum supported
link speed and will operate at the max speed.
Cc: stable@vger.kernel.org
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reported-by: Eda Zhou <ezhou@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'Commit cc27b735ad ("PCI/portdrv: Turn off PCIe services during
shutdown")' has been added to kernel to shutdown pending PCIe port service
interrupts during reboot so that a newly started kexec kernel wouldn't
observe pending interrupts.
pcie_port_device_remove() is disabling the root port and switches by
calling pci_disable_device() after all PCIe service drivers are shutdown.
This has been found to cause crashes on HP DL360 Gen9 machines during
reboot due to hpsa driver not clearing the bus master bit during the
shutdown procedure by calling pci_disable_device().
Disable device as part of the shutdown sequence.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199779
Fixes: cc27b735ad ("PCI/portdrv: Turn off PCIe services during shutdown")
Cc: stable@vger.kernel.org
Reported-by: Ryan Finnie <ryan@finnie.org>
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a drive with variable zone sizes or an invalid last zone size is
detected, the local variable this_zone_blocks is set to 0 and early return
from the function triggered, but this does not result in an error return.
The local variable zone_blocks must be set to 0 for an error to be
returned.
[mkp: typo in commit description]
Fixes: ccce20fc79 ("scsi: sd_zbc: Avoid that resetting a zone fails sporadically")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For one GFP_DMA32 does not actually work with kmalloc, as we only have
GFP_DMA and GFP_KERNEL caches, but not GFP_DMA32. Second the memory
is mapped using the proper DMA API anyway, which would include proper
bounce buffering if needed by the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlsU1hwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYPraxAAocC7JiFKW133/VugCtGA1x9uE8DPHealtsWTAeEq
KOOB3GxWMU2hKqQ4km5tcfdWoGJvvab6hmDXcitzZGi2JajO7Ae0FwIy3yvxSIKm
iH/ON7c4sJt8gKrXYsLVylmwDaimNs4a6xfODoCRgnWuovI2QrrZzupnlzPNsiOC
lv8ezzcW+Ay/gvDD/r72psO+w3QELETif/OzR/qTOtvLrVabM06eHmPQ8Wb98smu
/UPMMv6/3XwQnxpxpdyqN+p/gUdneXithzT261wTeZ+8gDXmcWBwHGcMBCimcoBi
FklW52moazIPIsTysqoNlVFsLGJTeS4p2D3BLAp5NwWYsLv+zHUVZsI1JY/8u5Ox
mM11LIfvu9JtUzaqD9SvxlxIeLhhYZZGnUoV3bQAkpHSQhN/xp2YXd5NWSo5ac2O
dch83+laZkZgd6ryw6USpt/YTPM/UHBYy7IeGGHX/PbmAke0ZlvA6Rae7kA5DG59
7GaLdwQyrHp8uGFgwze8P+R4POSk1ly73HHLBT/pFKnDD7niWCPAnBzuuEQGJs00
0zuyWLQyzOj1l6HCAcMNyGnYSsMp8Fx0fvEmKR/EYs8O83eJKXi6L9aizMZx4v1J
0wTolUWH6SIIdz474YmewhG5YOLY7mfe9E8aNr8zJFdwRZqwaALKoteRGUxa3f6e
zUE=
=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
Eve of merge window fix: The original code was so bogus as to be
casting the wrong generic device to an rport and proceeding to take
actions based on the bogus values it found. Fortunately it seems the
location that is dereferenced always exists, so the code hasn't oopsed
yet, but it certainly annoys the memory checkers.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWxMJDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWkTAP0QPfpP
ywyhrODRRPNg73zZnF3qo3CSeswSxDdjyW/4JAD/aLgTfPOydD+EA/sr/hjcs+Z/
DU3lt68c+CVp1kRtZ9A=
=9sLD
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Eve of merge window fix: The original code was so bogus as to be
casting the wrong generic device to an rport and proceeding to take
actions based on the bogus values it found.
Fortunately it seems the location that is dereferenced always exists,
so the code hasn't oopsed yet, but it certainly annoys the memory
checkers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_transport_srp: Fix shost to rport translation
Bsg holding a reference to the parent device may result in a crash if a
bsg file handle is closed after the parent device driver has unloaded.
Holding a reference is not really needed: the parent device must exist
between bsg_register_queue and bsg_unregister_queue. Before the device
goes away the caller does blk_cleanup_queue so that all in-flight
requests to the device are gone and all new requests cannot pass beyond
the queue. The queue itself is a refcounted object and it will stay
alive with a bsg file.
Based on analysis, previous patch and changelog from Anatoliy Glagolev.
Reported-by: Anatoliy Glagolev <glagolig@gmail.com>
Reviewed-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
libiscsi is the only SCSI code that return BLK_EH_HANDLED, thus trying to
bypass the normal SCSI EH code. We are going to remove this return value
at the block layer, and at least from a quick look it doesn't look too
harmful to try to send an abort for these cases, especially as the first
one should not actually be possible. If this doesn't work out iscsi
will probably need its own eh_strategy_handler instead to just do the
right thing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BLK_EH_NOT_HANDLED implies nothing happen, but very often that
is not what is happening - instead the driver already completed the
command. Fix the symbolic name to reflect that a little better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since an SRP remote port is attached as a child to shost->shost_gendev
and as the only child, the translation from the shost pointer into an
rport pointer must happen by looking up the shost child that is an
rport. This patch fixes the following KASAN complaint:
BUG: KASAN: slab-out-of-bounds in srp_timed_out+0x57/0x110 [scsi_transport_srp]
Read of size 4 at addr ffff880035d3fcc0 by task kworker/1:0H/19
CPU: 1 PID: 19 Comm: kworker/1:0H Not tainted 4.16.0-rc3-dbg+ #1
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0x85/0xc7
print_address_description+0x65/0x270
kasan_report+0x231/0x350
srp_timed_out+0x57/0x110 [scsi_transport_srp]
scsi_times_out+0xc7/0x3f0 [scsi_mod]
blk_mq_terminate_expired+0xc2/0x140
bt_iter+0xbc/0xd0
blk_mq_queue_tag_busy_iter+0x1c7/0x350
blk_mq_timeout_work+0x325/0x3f0
process_one_work+0x441/0xa50
worker_thread+0x76/0x6c0
kthread+0x1b2/0x1d0
ret_from_fork+0x24/0x30
Fixes: e68ca75200 ("scsi_transport_srp: Reduce failover time")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QBaF
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180524' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two fixes that should go into this release:
- a loop writeback error clearing fix from Jeff
- the sr sense fix from myself"
* tag 'for-linus-20180524' of git://git.kernel.dk/linux-block:
loop: clear wb_err in bd_inode when detaching backing file
sr: pass down correctly sized SCSI sense buffer
We're casting the CDROM layer request_sense to the SCSI sense
buffer, but the former is 64 bytes and the latter is 96 bytes.
As we generally allocate these on the stack, we end up blowing
up the stack.
Fix this by wrapping the scsi_execute() call with a properly
sized sense buffer, and copying back the bits for the CDROM
layer.
Cc: stable@vger.kernel.org
Reported-by: Piotr Gabriel Kosinski <pg.kosinski@gmail.com>
Reported-by: Daniel Shapira <daniel@twistlock.com>
Tested-by: Kees Cook <keescook@chromium.org>
Fixes: 82ed4db499 ("block: split scsi_request out of struct request")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This shall help avoid copying uninitialized memory to the userspace when
calling ioctl(fd, SG_IO) with an empty command.
Reported-by: syzbot+7d26fc1eea198488deab@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use remove_proc_subtree to remove the whole subtree on cleanup, and
unwind the registration loop into individual calls. Switch to use
proc_create_seq where applicable.
Also don't bother handling proc_create* failures - the driver works
perfectly fine without the proc files, and the cleanup will handle
missing files gracefully.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use remove_proc_subtree to remove the whole subtree on cleanup, and
unwind the registration loop into individual calls. Switch to use
proc_create_single.
Also don't bother handling proc_create* failures - the driver works
perfectly fine without the proc files, and the cleanup will handle
missing files gracefully.
Signed-off-by: Christoph Hellwig <hch@lst.de>
"make clean" should remove the generated file "scsi_devinfo_tbl.c", so
list it in the clean-files variable so that the file gets cleaned up.
Fixes: 345e29608b ("scsi: scsi: Export blacklist flags to sysfs")
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Same numerical value (for now at least), but a much better documentation
of intent.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_old_get_request already has it at hand, and in blk_queue_bio, which
is the fast path, it is constant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch everyone to blk_get_request_flags, and then rename
blk_get_request_flags to blk_get_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Always GFP_KERNEL, and keeping it would cause serious complications for
the next change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can rely on the dma-mapping code to handle any DMA limits that is
bigger than the ISA DMA mask for us (either using an iommu or swiotlb),
so remove setting the block layer bounce limit for anything but the
unchecked_isa_dma case, or the bouncing for highmem pages.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
commit b60710ec7d ("scsi: aacraid: enable sending of TMFs from
aac_hba_send()") allows aac_hba_send() to send scsi commands, and TMF
requests, but the existing code only updates the iu_type for scsi
commands. For TMF requests we are sending an unknown iu_type to
firmware, which causes a fault.
Include iu_type prior to determining the validity of the command
Reported-by: Noah Misner <nmisner@us.ibm.com>
Fixes: b60710ec7d ("aacraid: enable sending of TMFs from aac_hba_send()")
Fixes: 423400e64d ("aacraid: Include HBA direct interface")
Tested-by: Noah Misner <nmisner@us.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The vmw_pvscsi driver returns DID_ABORT for commands aborted internally
by the adapter, leading to the filesystem going read-only. Change the
result to DID_BUS_BUSY, causing the kernel to retry the command.
Signed-off-by: Jim Gill <jgill@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case when the phy_mask is bitwise anded with the phy_index bit is
zero the continue statement currently jumps to the next iteration of the
while loop and phy_index is never actually incremented, potentially
causing an infinite loop if phy_index is less than SCI_MAX_PHS. Fix this
by turning the while loop into a for loop.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike SCSI and FC, we don't use multiple channels for IDE. Also fix
the calculation for sub-channels.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since SCSI scanning occurs asynchronously, since sd_revalidate_disk() is
called from sd_probe_async() and since sd_revalidate_disk() calls
sd_zbc_read_zones() it can happen that sd_zbc_read_zones() is called
concurrently with blkdev_report_zones() and/or blkdev_reset_zones(). That can
cause these functions to fail with -EIO because sd_zbc_read_zones() e.g. sets
q->nr_zones to zero before restoring it to the actual value, even if no drive
characteristics have changed. Avoid that this can happen by making the
following changes:
- Protect the code that updates zone information with blk_queue_enter()
and blk_queue_exit().
- Modify sd_zbc_setup_seq_zones_bitmap() and sd_zbc_setup() such that
these functions do not modify struct scsi_disk before all zone
information has been obtained.
Note: since commit 055f6e18e0 ("block: Make q_usage_counter also track
legacy requests"; kernel v4.15) the request queue freezing mechanism also
affects legacy request queues.
Fixes: 89d9475610 ("sd: Implement support for ZBC devices")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # v4.16
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A drive being sanitized will return NOT READY / ASC 0x4 / ASCQ
0x1b ("LOGICAL UNIT NOT READY. SANITIZE IN PROGRESS").
Prevent spinning up the drive until this condition clears.
[mkp: tweaked commit message]
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 2d2c233167 ("scsi: megaraid_sas: modified few prints in OCR and IOC INIT path")
Signed-off-by: Vinson Lee <vlee@freedesktop.org>
Acked-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add UFS Protocol Information Units(upiu) trace events for ufs driver,
used to trace various ufs transaction types- command, task-management
and device management.
The trace-point format is generic and can be easily adapted to trace
other upius if needed.
Currently tracing ufs transaction of type 'device management', which
this patch introduce, cannot be obtained from any other trace.
Device management transactions are used for communication with the
device such as reading and writing descriptor or attributes etc.
Signed-off-by: Ohad Sharabi <ohad.sharabi@sandisk.com>
Reviewed-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in fnic stats message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch titled: "[PATCH v2] scsi_debug: implement IMMED bit" introduced
long delays to the Start stop unit (SSU) and Synchronize cache (SC)
commands when the IMMED bit is clear. This patch makes those delays
more realistic. It causes SSU to only delay when the start stop state is
changed; SC only delays when there's been a write since the previous
SC. It also reduced the SC delay from 1 second to 50 milliseconds.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of always multicasting responses, send a unicast netlink message
directed at the correct pid. This will be needed if we ever want to
support multiple userspace processes interacting with the kernel over
iSCSI netlink simultaneously. Limitations can currently be seen if you
attempt to run multiple iscsistart commands in parallel.
We've fixed up the userspace issues in iscsistart that prevented
multiple instances from running, so now attempts to speed up booting by
bringing up multiple iscsi sessions at once in the initramfs are just
running into misrouted responses that this fixes.
Signed-off-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes. The status handling code is
actually a running regression from the previous merge window which had
an incomplete fix (now reverted) and most of the remaining bug fixes
are for problems older than the current merge window.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWtMW7SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYdtAP97FhqR
x2lDO7J6QT8hMVqwPeQS0Xh5ZPbZLedPmfx9BAD+K1HauGv8J/eMggMDPGrWa/CP
tGrg2UorMrokLLdIbyA=
=fOJs
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
The status handling code is actually a running regression from the
previous merge window which had an incomplete fix (now reverted) and
most of the remaining bug fixes are for problems older than the
current merge window"
[ Side note: this merge also takes the base kernel git repository to 6+
million objects for the first time. Technically we hit it a couple of
merges ago already if you count all the tag objects, but now it
reaches 6M+ objects reachable from HEAD.
I was joking around that that's when I should switch to 5.0, because
3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
probably not, even if numerology is about as good a reason as any.
- Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
scsi: aacraid: Insure command thread is not recursively stopped
scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
scsi: qla2xxx: correctly shift host byte
scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
scsi: qla2xxx: Avoid double completion of abort command
scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
scsi: scsi_dh: Don't look for NULL devices handlers by name
scsi: core: remove redundant assignment to shost->use_blk_mq
The Windows Server 2016 iSCSI target doesn't work with the Linux kernel
initiator since the kernel started sending larger requests by default,
nor does it implement the block limits VPD page. Apply the sector limit
workaround for these targets.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: KY Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch marks skb->data as untrusted so it complains that there is a
potential overflow here:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:2111 t4_uld_rx_handler()
error: buffer overflow 'cxgb4i_cplhandlers' 239 <= 255.
In this case, skb->data comes from the hardware or firmware so it's not
going to overflow unless there is a firmware bug.
[mkp: fixed braces]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is another use after free if we reset the card. The adpt_hba_reset()
function frees "pHba" on error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ensure that CONDITION MET and other non-zero status values that indicate
success are translated into BLK_STS_OK.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Lee Duncan <lduncan@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the next patch will modify this function such that it checks more than
just the host byte of the SCSI result, rename __scsi_error_from_host_byte()
into scsi_result_to_blk_status(). This patch does not change any
functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Lee Duncan <lduncan@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The description of commit e39a97353e is wrong: it mentions that commit
2a842acab1 introduced a bug in __scsi_error_from_host_byte() although that
commit did not change the behavior of that function. Additionally, commit
e39a97353e introduced a bug: it causes commands that fail with
hostbyte=DID_OK and driverbyte=DRIVER_SENSE to be completed with
BLK_STS_OK. Hence revert that commit.
Fixes: e39a97353e ("scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()")
Reported-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Lee Duncan <lduncan@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart reports that in qla_isr.c's qla2x00_handle_dif_error we're wrongly
shifting the SAM_STAT_CHECK_CONDITION by one instead of directly ORing it
onto the SCSI command's result.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI host byte has to be shifted by 16 not 6.
As Bart pointed out this patch does not change any functionality because
DID_OK == 0, but a wrong shift is irritating for the reviewer.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_init_timer() calls add_timer() on the iocb timeout timer, which
means the timeout function pointer and any data that the function depends on
must be initialised beforehand.
Move this initialisation before each call to qla2x00_init_timer(). In some
cases qla2x00_init_timer() initialises a completion structure needed by the
timeout function, so move the call to add_timer() after that.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_tmf_sp_done() now deletes the timer that will run
qla2x00_tmf_iocb_timeout(), but doesn't check whether the timer already
expired. Check the return value from del_timer() to avoid calling
complete() a second time.
Fixes: 4440e46d5d ("[SCSI] qla2xxx: Add IOCB Abort command asynchronous ...")
Fixes: 1514839b36 ("scsi: qla2xxx: Fix NULL pointer crash due to active ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code that fixes the crashes in the following commit introduced a small
memory leak:
commit 6a2cf8d366 ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure")
Fixing this requires a bit of reworking, which I've explained. Also provide
some code cleanup.
There is a small window in qla2x00_probe_one where if qla2x00_alloc_queues
fails, we end up never freeing req and rsp and leak 0xc0 and 0xc8 bytes
respectively (the sizes of req and rsp).
I originally put in checks to test for this condition which were based on
the incorrect assumption that if ha->rsp_q_map and ha->req_q_map were
allocated, then rsp and req were allocated as well. This is incorrect.
There is a window between these allocations:
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
goto probe_hw_failed;
[if successful, both rsp and req allocated]
base_vha = qla2x00_create_host(sht, ha);
goto probe_hw_failed;
ret = qla2x00_request_irqs(ha, rsp);
goto probe_failed;
if (qla2x00_alloc_queues(ha, req, rsp)) {
goto probe_failed;
[if successful, now ha->rsp_q_map and ha->req_q_map allocated]
To simplify this, we should just set req and rsp to NULL after we free
them. Sounds simple enough? The problem is that req and rsp are pointers
defined in the qla2x00_probe_one and they are not always passed by reference
to the routines that free them.
Here are paths which can free req and rsp:
PATH 1:
qla2x00_probe_one
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
[req and rsp are passed by reference, but if this fails, we currently
do not NULL out req and rsp. Easily fixed]
PATH 2:
qla2x00_probe_one
failing in qla2x00_request_irqs or qla2x00_alloc_queues
probe_failed:
qla2x00_free_device(base_vha);
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 3:
qla2x00_probe_one:
failing in qla2x00_mem_alloc or qla2x00_create_host
probe_hw_failed:
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 1: This should currently work, but it doesn't because rsp and rsp are
not set to NULL in qla2x00_mem_alloc. Easily remedied.
PATH 2: req and rsp aren't passed in at all to qla2x00_free_device but are
derived from ha->req_q_map[0] and ha->rsp_q_map[0]. These are only set up if
qla2x00_alloc_queues succeeds.
In qla2x00_free_queues, we are protected from crashing if these don't exist
because req_qid_map and rsp_qid_map are only set on their allocation. We are
guarded in this way:
for (cnt = 0; cnt < ha->max_req_queues; cnt++) {
if (!test_bit(cnt, ha->req_qid_map))
continue;
PATH 3: This works. We haven't freed req or rsp yet (or they were never
allocated if qla2x00_mem_alloc failed), so we'll attempt to free them here.
To summarize, there are a few small changes to make this work correctly and
(and for some cleanup):
1) (For PATH 1) Set *rsp and *req to NULL in case of failure in
qla2x00_mem_alloc so these are correctly set to NULL back in
qla2x00_probe_one
2) After jumping to probe_failed: and calling qla2x00_free_device,
explicitly set rsp and req to NULL so further calls with these pointers do
not crash, i.e. the free queue calls in the probe_hw_failed section we fall
through to.
3) Fix return code check in the call to qla2x00_alloc_queues. We currently
drop the return code on the floor. The probe fails but the caller of the
probe doesn't have an error code, so it attaches to pci. This can result in
a crash on module shutdown.
4) Remove unnecessary NULL checks in qla2x00_free_req_que,
qla2x00_free_rsp_que, and the egregious NULL checks before kfrees and vfrees
in qla2x00_mem_free.
I tested this out running a scenario where the card breaks at various times
during initialization. I made sure I forced every error exit path in
qla2x00_probe_one.
Cc: <stable@vger.kernel.org> # v4.16
Fixes: 6a2cf8d366 ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently scsi_dh_lookup() doesn't check for NULL as a device name. This
combined with nvme over dm-mpath results in the following messages
emitted by device-mapper:
device-mapper: multipath: Could not failover device 259:67: Handler scsi_dh_(null) error 14.
Let scsi_dh_lookup() fail fast on NULL names.
[mkp: typo fix]
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
