The new controls will give user the ability to route the left PDM channel
data to the right headset/handsfree DAC.
HS mono to stereo switch: PDM channel 1 (or mono) data to both HS DAC.
HF mono to stereo switch: PDM channel 3 data to both HF DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating the codec dai, use sig_bits to update the max bps based
on the codec capability. So both the link DMA and codec format will be
calculated based on DAI sig_bits.
So update the sig_bits with converter capability and use the sig_bits
for HDA format calculation.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error path in probe attempts to put the device back into reset.
Should we fail to get the reset_gpio (such as a probe defer) we will
leave the error value in there, which the gpiod_set_value_cansleep on
the error path will attempt to deference.
Fix this issue by clearing reset_gpio before we head into the error
path.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WM8960 derives bit clock from sysclock using BCLKDIV[3:0] of R8
clocking register (See WM8960 datasheet, page 71).
There are use cases, like this:
aplay -Dhw:0,0 -r 48000 -c 1 -f S20_3LE -t raw audio48k20b_3LE1c.pcm
where no BCLKDIV applied to sysclock can give us the exact requested
bitclk, so driver fails to configure clocking and aplay fails to run.
Fix this by relaxing bitclk computation, so that when no exact value
can be derived from sysclk pick the closest value greater than
expected bitclk.
Suggested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a separate function for finding (sysclk, lrclk, bclk)
when the clock is auto or mclk. This makes code easier to
read and reduces the indentation level in wm8960_configure_clocking.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pre divider control register of IF1 and IF2/3 are different.
The driver used the same register for all interfaces which was a
mistake.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift is RT5665_IF2_1_ADC_IN_SFT not RT5665_IF3_ADC_IN_SFT.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8903 has four different voltage inputs: AVDD, CPVDD, DBVDD
and DCVDD. On the Qualcomm APQ8060 Dragonboard these are all
supplied from proper regulators and thus need activating and
binding.
This is a quick-and-dirty solution just grabbing and enabling the
regulator supplies on probe() and disabling them on remove() and
the errorpath. More elaborate power management is likely possible.
I assume the nVidia designs using this codec have some hard-wired
always-on power and will be happy with using the dummy regulators
for this. But someone from the nVidia camp should probably check
whether they can bind these to proper regulators instead.
We also amend the DT binding document. A small change like this
does not warrant a separate patch for augmenting these.
Cc: devicetree@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver stashes a CODEC pointer in the cs35l35_private structure,
which is used to obtain a struct device pointer for error messages in the
interrupt handler.
However, doing so is not very safe as the interrupt is registered, as it
should be in bus probe, but the CODEC pointer can't be safely stored until
the ASoC level probe. This leaves a window between the two probes where if
any interrupts are received a NULL pointer will be deferenced in the IRQ
handler.
Fix this issue by saving a pointer to the device directly and passing that
to the error messages in the interrupt handler rather than using the CODEC
pointer to access the device pointer.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S2 and I2S3 are share pins. We need to configure it when i2s is
active and disable it when i2s is inactive. To disable i2s pins
means to set them as gpio.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the ADI AU1761 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected
for ADI blackfin devices or if SND_SOC_ALL_CODECS is enabled.
Signed-off-by: Bryce Ferguson <bryce.ferguson@rockwellcollins.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_pll function to codec level and people can use it at both
codec and dai level. Also, lower case "source" to keep it consistent.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs35l35->pdata.stereo is false then "ret" isn't initialized.
Fixes: 6387f866a2 ("ASoC: Add support for Cirrus Logic CS35L35 Amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extraneous tab to correct the nesting level indentation
Detected by CoverityScan, CID#1416584 ("Nesting level does
not match indentation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As it is quite common to use a stereo pair of amps but share the IRQ
line between them both add the IRQF_SHARED flag whilst requesting
cs35l35's IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidy up the code a little by adding a local variable for i2c_client->dev
rather than referring to it explicitly everytime.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting how the I2S pins are driven in unused slots,
currently the chip will just use the default of drive 0, however this
causes issues when multiple devices are attached to the same bus.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A return statement is missing just before the error paths at the end of
probe. This causes us to fall straight into the error path and disable
the supplies and re-enable reset, as these are only controlled during
probe this causes the part to no longer function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use manual mode for jack detection function to increase accuracy.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM is necessary for more than 2 channels. And there is no control bit
to specify which slots are using. Machine driver will not need to call
snd_soc_dai_set_tdm_slot if we do it in rt5665_hw_params.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vref3 is necessary for Mono Amp. So add it to dapm routes
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We got rt5665 private data from wrong work. It will result in kernel
panic.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Use the "cansleep" variant of gpiod_set_value so the driver can be used
with slow gpio controllers as well.
Fixes: 85825d5e88 ("ASoC: dio2125: add dio2125 amp driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is a stereo output driver with adjustable gain.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not be writing acknowledge controls until the firmware is
running, as in the case of preloaded firmwares the DSP memory may be
unaccessible to whilst in the preloaded state. This means a write to the
control during this time could be lost.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Volatile controls should only be accessed when the firmware is active,
currently however writes to these controls will succeed, but the data
will be lost, if the firmware is powered down. Update this behaviour such
that an error is returned the same as it is for reads.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es7134 is 24bit, 192Khz i2s DA converter for PCM audio.
Datasheet is available here : http://www.everest-semi.com/pdf/ES7134LV%20DS.pdf
This driver is also compatible with the es7144, which is the same as the
es7134, with 2 additional pins for filtering capacitors.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix not to update the iterator element, instead use list_del to remove
entry from the list.
This fixes the following coccinelle and static checker warning:
sound/soc/codecs/hdac_hdmi.c:1884:2-21:iterator with update on line
1885
sound/soc/codecs/hdac_hdmi.c:2011 hdac_hdmi_dev_remove()
error: potential NULL dereference 'port'.
Fixes: e0e5d3e5a53b('ASoC: hdac_hdmi: Add support for multiple ports to a PCM')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pin list array iterator outside the iteration of the list can
point to dummy element, which can be invalid. So don't use pin variable
outside the pin list iteration.
This fixes the following coccinelle warning:
sound/soc/codecs/hdac_hdmi.c:1419:5-8: ERROR: invalid reference to the
index variable of the iterator
Fixes: 2acd8309a3a4('ASoC: hdac_hdmi: Add support to handle MST capable pin')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without this I am getting the following messages at boot on my Trimslice:
tlv320aic23-codec 2-001a: Control not supported for path LLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for LLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route LLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path RLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for RLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route RLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path MICIN -> [NULL] -> Mic Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for MICIN --> NULL --> Mic Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route MICIN -> NULL -> Mic Input
tegra-snd-trimslice sound: tlv320aic23-hifi <-> 70002800.i2s mapping ok
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The master and slave modes don't share the same table for MCLK/LRCLK
ratios. The slaves mode has bigger ratios that allow to use BCLK that
matche sampling frequency of 192khz.
This commit enables this rate only for slave mode, i.e it does not
declare this frequency in sysclk_contraints, resulting to an error in
master mode (not supported CLK).
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently most of the standard rates are supported by this driver.
Instead of defining each supported rate one by one, we use the SND macro
SNDRV_PCM_RATE_8000_48000. Also adds support for 88.2khz as the codec
supports it and the sys clocks are already supported.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In master mode, SCLK and LRCLK signals are generated by the CODEC when
any of the ADC/DAC are enabled. SCLK is derived from MCLK via a
programmable division set by BLK_DIV, LRCLK is derived from MCLK via
another programmable division set by ADCFsRatio/DACFsRatio.
In slave mode, SCLK and LRCLK signals are received as inputs and
supplied externally. LRCLK and SCLK must be synchronously derived from
MCLK with specific rates. The device can auto detect MCLK/LRCLK ratio
according to a predefined table. LRCLK/SCLK ratio is usually 64 (SCLK =
64 * LRCLK)
This commits adds support to let to device auto detect and decide which
ratio to use. The mclkdiv2 and BCLK_DIV ratio and put to zero.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
unneded||unneeded
Link: http://lkml.kernel.org/r/1481573103-11329-15-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
configurable LRC and BCLK divide. The driver
will make configurations of LRC and BCLK automatically according to
BCLK and FS information in master mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is new Intel SoC, so add codec entry for HDMI
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Represent each port as machine DAPM pin widget. This helps in
enable/disable pin when monitor is connected/disconnected in case pcm
is rendered to multiple ports.
Create machine pin widgets and pin switch kcontrol for each port and
report based on the pin status
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_jack instead of snd_jack and create the jack in machine
driver and pass the jack pointer to hdac_hdmi driver for jack
reporting.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have the MST feature enabled and Pin-Port mux for user to
select the converter routing, multiple port mapping to same converter
needs to be supported.
To support multiple port mapped to same converter following changes are
done for this:.
o Add port list to pcm, so that multiple ports can be mapped to a PCM.
o Jack reporting in case where multiple port are attached to same PCM.
o Change hdac_hdmi_get_port_from_cvt(), channel_map, remove functions
to parse through all ports mapped to same the PCM.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable stream on a specific port of a MST capable pin, the port
needs to be selected before we configure the pin widget verb.
When port is selected, all the pin widget verb controlling the sink
device operation will be directed to selected port. So add port
selection before configuring the pin widget verb.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ELD notification can be received asynchronously from the graphics
side and this may happen just at the moment the sound driver is
initializing and notification will be missed. Similarly at system
resume, the notification is ignored as the ELD and connection states
are updated in anyway at the end of the resume.
So check the jack status in boot/resume by querying the port presence
based on pin caps and report the jack status.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support DP MST audio, new pin verbs/params are added. This patch
adds helper functions to do following:
o To set a specific port
o To get the currently selected port
o To get the length of port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While unregistering the hdmi-codec, the hdmi device list must be
cleaned up. It avoid kernel page fault when registering again the
hdmi-codec.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle jack event and configuration of the pin widget for MST
capable pin, this patch adds:
o Flag to identify the pin is MST capable.
o In notify callback(), based on the pipe and port information marks if
the port is mst_capable. In case of non MST, port is defaulted to zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With MST each pin contains several ports to which device can be
connected.
As a preparatory work to support DP MST this patch adds below changes:
1. Defines the port structure and moves all stream related information
like ELD, converter list, chmap to port.
2. Creates ports for each pin based on the max_ports support.
3. Based on Pin-Port combination creates DAPM Mux widget instead of Pin
to allow user to select a converter.
4. Port zero is the default port when pin does not support MST.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two front-ends to the codec can now be selected individually, but fail to
build when the bus support is missing:
sound/built-in.o: In function `es8328_spi_probe':
es8328-spi.c:(.text+0x125854): undefined reference to `__devm_regmap_init_spi'
sound/built-in.o: In function `es8328_spi_driver_init':
es8328-spi.c:(.init.text+0x3589): undefined reference to `__spi_register_driver'
Related to this, the added dependency on SND_SOC_ES8328 breaks:
warning: (SND_SOC_ALL_CODECS) selects SND_SOC_ES8328_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_ES8328 && I2C)
This adds the respective Kconfig dependencies and changes SND_SOC_ES8328 to a hidden
symbol that is selected implicitly by the two more specific options, as we do for
some other codecs. We have to remove the 'depends on' for SND_SOC_IMX_ES8328 in the
same step to avoid a recursive dependency.
Fixes: aa00f2c8af ("ASoC: Allow to select ES8328_I2C and ES8328_SPI directly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we have to select these symbols explictly via Kconfig, from
another entry. If we plan to use generic audio drivers like
simple-audio-card, the user need to be able to enable these symbols
directly via the menuconfig.
This commit also fixes unmet dependencies to SND_SOC_IMX_ES8328 caused
by these changes.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the function that changes the DAI format only supports master
mode. Trying to use a slave mode exits the function with -EINVAL and
leave the codec misconfigured. This commits adds support for enabling
the slave mode.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel info is part of the pcm parameter and channel map control is
created for each pcm. So move channel info to pcm instead of pin
structure and the mutex lock to pcm.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Optional gpio handling should not cause an error status and prevent
probing if it's missing. Remove error return for -ENOENT case and
move error message to dev_info
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This macro is unused since commit e369bd006f ("ASoC: wm8741: Allow master
clock switching").
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALC3270 is a low-cost version of RT5645, add ACPI ID
to enable probe and use rt5645 codec driver
Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add ACPI ID 10EC5648 found e.g on Asus X205TA and use
rt5645 driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the BIOS incorrectly reports this codec as 5640 but it is
really a rt5670
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ACPI ID "10EC3276" for sound card found on notebook HP Pavilion X2 10-p000.
ACPI DSDT Table on this device describes this card as ALC3276, but it is in fact rt5640.
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CQ0093VC is no longer dependent on MFD_DAVINCI_VOICECODEC,
let's remove it. Otherwise, we can't compile it by COMPILE_TEST
on non-DAVINCE platform
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of hdmi connect/disconnect or when stream need to be route to
multiple monitors, corresponding port and audio infoframe needs to be
reconfigured. Currently all the configuration are done in DAI ops which
results in silence playback.
So use dapm widget event handlers to program audio infoframe and enable
/disable port configuration when widget is power on/off.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we are not disabling MEM_ENA on the error path, we should
really do this to unwind the state back to how it was. This patch adds a
clear of MEM_ENA on the error path, again there is no major issues
caused by this minor fix.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The booted and running flags should really only be set once all the
steps at that power level have been complete. Currently operations can
fail after the flags have been set, which would leave us in an
inconsistent state where the flags are set but the things expected to
reach that level have not happened. Whilst there isn't really any major
impact from this it is best to clean it up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent refactoring overlooked some places which should be covered by
the pwr_lock, all code that affects or depends on the power status of
the DSP should be covered, this patch adds the missing coverage.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds a compatible string for everest,es8388. This is
an audio codec that is compatible with es8328.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add user interface to provide channel mapping.
In a first step this control is read only.
As TLV type, the control provides all configuration available for
HDMI sink(ELD), and provides current channel mapping selected by codec
based on ELD and number of channels specified by user on open.
When control is called before the number of the channel is specified
(i.e. hw_params is set), it returns all channels set to UNKNOWN.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With codec read sometimes the pin_sense shows invalid monitor present
and eld_valid. Currently driver polls for few times to get the valid
eld data.
To avoid the latency, Instead of reading ELD from codec, read it
directly from the display driver using audio component framework.
and removed the unused direct codec helper functions.
Signed-off-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of enabling pin and cvt in pcm_open(), need to restore pin and
cvt state after system resume to restart the playback which is
paused/stopped before system suspend.
So enable pin and cvt in playback_prepare and call prepare when trigger
cmd is paused/started and resume to reconfigure pin and cvt.
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
arizona_spk_init uses snd_soc_dapm_new_control which since
commit 37e1df8c95 ("ASoC: dapm: handle probe deferrals") will
occasionally request a probe deferral. Which means we should propagate the
error out of our driver from it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5659.c:4236:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. For this large delay msleep() is preferable.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2b26dd4c1f ("ASoC: rt5660: add rt5660 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the const qualifier as it is being added by SOC_ENUM_DOUBLE_DECL()
already which is called by SOC_ENUM_SINGLE_DECL() here.
Fixes: commit 2b26dd4c1f ("ASoC: rt5660: add rt5660 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the const qualifier as it is being added by SOC_ENUM_DOUBLE_DECL()
already which is called by SOC_ENUM_SINGLE_DECL() as well as the
double const by calls to SOC_VALUE_ENUM_SINGLE_DECL() via
SOC_VALUE_ENUM_DOUBLE_DECL).
Fixes: commit d3cb2de247 ("ASoC: rt5659: add rt5659 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declar rt5659_i2c_driver, which is only being passed to
module_i2c_driver(rt5659_i2c_driver), static.
Fixes: commit d3cb2de247 ("ASoC: rt5659: add rt5659 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. For this large delay msleep() is preferable.
Fixes: commit d3cb2de247 ("ASoC: rt5659: add rt5659 codec driver")
Link: http://lkml.org/lkml/2017/1/11/377
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 70/80ms delays here passing the "min"
value to msleep(). This reduces the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 246693ba7b ("ASoC: rt5640: change widget sequence for depop")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace mdelay to msleep to avoid busy loop on ak4642_lout_event().
Otherwise, sometimes playback doesn't work correctly when pulseaudio
was used.
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to use simple card with wm8962 the following probe
error happens:
wm8731 0-001a: simple-card: set_sysclk error
In simple-card.c the snd_soc_dai_set_sysclk() function is called with
clk_id as 0, which is an invalid clock for wm8731.
Adjust the clocks source definitions in wm8731.h so that the simple
card driver can work successfully
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Mark Brown <broonie@kernel.org>
