With this patch bnx2x will configure the PF to perform Tx switching on
out-going traffic as soon as SR-IOV is dynamically enabled and de-activate
it when it is disabled.
This will allow VFs to communicate with their parent PFs.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull request of three patches for net-next/master.
Oleg Moroz added support for a new PCI card to the generic SJA1000 PCI
driver, Guenter Roeck's patch limits the flexcan driver to little
endian arm (and powerpc) and I fixed a sparse warning found by the
kbuild robot in the ti_hecc driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60e453a940 ("USBNET: fix handling padding packet")
added an extra SG entry in case padding is necessary, but
failed to update the initialisation of the list. This can
cause list traversal to fall off the end of the list,
resulting in an oops.
Fixes: 60e453a940 ("USBNET: fix handling padding packet")
Reported-by: Thomas Kear <thomas@kear.co.nz>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c466a9b2b3
(net: 3com: slight optimization of addr compare)
cause a warning: "passing argument 1 of 'ether_addr_equal'
from incompatible pointer type", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6878f79a8b
(net: qlcnic: slight optimization of addr compare)
cause a warning "sparse: incorrect type in argument 2
(different type sizes)", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_error() in case of a TX error tries to print a message using 2 dev_err()
calls with the first string not finished by '\n', so that the resulting message
would inevitably come out garbled, with something like "3net eth0: " inserted
in the middle. Avoid that by merging 2 calls into one.
While at it, insert an empty line after the nearby declaration.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the implementation is meaningless - once again, we take the
slave structure and use it after we've exited RCU critical section.
Fix this by removing the rcu_read_lock() from __get_active_agg(), and
ensuring that all its callers are holding RCU.
Fixes: be79bd048 ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the RCU read lock usage is just wrong - it gets the slave struct
under RCU and continues to use it when RCU lock is released.
However, it's still safe to do this cause we didn't need the
rcu_read_lock() initially - all of the __get_first_agg() callers are either
holding RCU read lock or the RTNL lock, so that we can't sync while in it.
Fixes: be79bd048 ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, its usage is just plainly wrong. It first gets a slave under
RCU, and, after releasing the RCU lock, continues to use it - whilst it can
be freed.
Fix this by ensuring that bond_3ad_set_carrier() holds RCU till it uses its
slave (or its agg).
Fixes: be79bd048a ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enabling BIT_9 while configuring hardware LRO allows adapter to
perform LRO even if destination IP address is not programmed in adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add __QLCNIC_SRIOV_ENABLE bit check before doing SRIOV cleanup
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored code to handle beaconing test for all adapters.
o Use GET_LED_CONFIG mailbox command for 83xx/84xx series adapter
to detect current beaconing state of the adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o MAC learning will be done for SRIOV PF to help program VLAN filters
onto adapter. This will help VNIC traffic to flow through without
flooding traffic.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o By default, SRIOV PF will have promiscous mode on.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o On enabling VF flood bit, PF driver will be able to receive traffic
from all its VFs.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter should allow vlan traffic only for vlans configured on a VF.
On configuring any vlan mode from VF, adapter will allow any vlan
traffic to pass for that VF. Do not allow VF to configure this mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_attach_direct() may now attach to a generic 10G driver. It can
also be used exactly as phy_connect_direct(), which will be useful
when using of_mdio, as phy_connect (and therefore of_phy_connect)
start the PHY state machine, which is currently irrelevant for 10G
PHYs.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very incomplete, but will allow for binding an ethernet controller
to it.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then other generic phy driver such as generic 10g phy driver can join it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bunch of whole lot of namespace issues with the Broadcom bnx2x driver
found by running 'make namespacecheck'
* global variables must be prefixed with bnx2x_
naming a variable int_mode, or num_queue is invitation to disaster
* make local functions static
* move some inline's used in one file out of header
(this driver has a bad case of inline-itis)
* remove resulting dead code fallout
bnx2x_pfc_statistic,
bnx2x_emac_get_pfc_stat
bnx2x_init_vlan_mac_obj,
Looks like vlan mac support in this driver was a botch from day one
either never worked, or not implemented or missing support functions
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If used 64 bit compiler GCC warns that:
drivers/net/ethernet/smsc/smc91x.c:1897:7:
warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
This patch fixes this by changing typecast from "unsigned int" to "unsigned long"
CC: "David S. Miller" <davem@davemloft.net>
CC: Jingoo Han <jg1.han@samsung.com>
CC: netdev@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use the native GRO handling of encapsulated protocols on
mlx4, we need to call napi_gro_receive() instead of netif_receive_skb()
unless busy polling is in action.
While we are at it, rename mlx4_en_cq_ll_polling() to
mlx4_en_cq_busy_polling()
Tested with GRE tunnel : GRO aggregation is now performed on the
ethernet device instead of being done later on gre device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc is a limited resource. Don't use it unnecessarily.
It seems this allocation should work with kcalloc.
Remove unnecessary memset(,0,) of buf as it's completely
overwritten as the previously only unset field in
struct qlcnic_pci_func_cfg is now set to 0.
Use kfree instead of vfree.
Use ETH_ALEN instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know how large "tp->vlan_shift" is but static checkers worry
about shift wrapping bugs here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That code has been around for ages without being used.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a huge mess currently, that is really hard to read. This cleanup
doesn't touch the logic at all, it only breaks easy-to-fix long lines and
updates comment styles.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and now i40evf.
Most notable is Jacob's patch to add PTP support to i40e.
Mitch cleans up additional memcpy's and use struct assignment instead.
Then fixes long lines to appease checkpatch.pl. Mitch then provides
a fix to keep us from spamming the log with confusing errors. If you
use ip to change the MAC address of a VF while the VF driver is loaded,
closing the VF interface or unloading the VF driver will cause the VF
driver to remove the MAC filter for its original (now invalid) MAC
address.
Jesse cleans up macros which are no longer needed or used.
I (Jeff) cleanup function header comments to ensure Doxygen/kdoc works
correctly to generate documentation without warnings.
Anjali fixes a bug where ethtool set-channels would return failure when
configuring only one Rx queue. Then fixes a bug where the driver was
erroneously exiting the driver unload path if one part of the unload
failed.
Shannon fixes if the IPV6EXADD but is set in the Rx descriptor status,
there was an optional extension header with an alternate IP address
detected and the hardware checksum was not handling the alternate IP
address correctly. Then adjusts the ITR max and min values to match
the hardware max value and recommended min value. Shannon makes sure
to clear the PXE mode after the adminq is initialized.
v2:
- fix patch 14 "i40e: enable PTP" to address Richard Cochran's spelling
catch and Ben Hutchings Kconfig, SIOCGHWTSTAMP and sizeof() suggestions
- added Paul Gortmaker's i40evf fix patch
v3:
- fix patch 14 "i40e: enable PTP" to address Ben Hutchings concerns about
a race with PTP init and cleanup and i40e_get_ts_info().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warning, which occurs in casts when
accessing the data in the CAN frames (struct can_frame) in the RX and TX
routines:
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:572:28: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:572:28: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:572:28: got restricted __be32 [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:575:40: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: got restricted __be32 [usertype] <noident>
As the data is indeed big endian, use "__be32" instead of "u32", when casting
it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Building arm:allmodconfig fails with
flexcan.c: In function 'flexcan_read':
flexcan.c:243:2: error: implicit declaration of function 'in_be32'
flexcan.c: In function 'flexcan_write':
flexcan.c:248:2: error: implicit declaration of function 'out_be32'
in_be32 and out_be32 do not (or no longer) exist for ARM targets.
Disable the build for ARM on big endian CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Elcus CAN200PCI card.
Signed-off-by: Oleg Moroz <oleg.moroz@mcc.vniiem.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As of commit 7f12ad741a ("i40evf: transmit
and receive functionality") the s390 builds (allyesconfig) fail with:
drivers/net/ethernet/intel/i40evf/i40e_txrx.c: In function 'i40e_clean_rx_irq':
drivers/net/ethernet/intel/i40evf/i40e_txrx.c:818:3: error: implicit declaration of function 'prefetch'
make[5]: *** [drivers/net/ethernet/intel/i40evf/i40e_txrx.o] Error 1
due to an implicit assumption that the prototype from linux/prefetch.h
will be present.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver version to 0.3.28-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.
Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.
Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the ITR max and min values to match the hardware max value
and the recommended min value. These values are shifted right
one bit because the register counts in 2 usec units, so leave
a comment to explain.
Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the IPV6EXADD bit is set in the Rx descriptor status, there
was an optional extension header with an alternate IP address
detected. The HW checksum offload doesn't handle the alternate
IP address correctly so likely comes up with the wrong answer.
Thus, if the bit is set we ignore the checksum offload value.
Change-ID: I70ff8d38cdcddccf44107691cae13d0c07c284c8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If you use ip to change the MAC address of a VF while the VF
driver is loaded, closing the VF interface or unloading the VF
driver will cause the VF driver to remove the MAC filter for its
original (now invalid) MAC address. This would cause the PF
driver to kick an error message to the log, and back to the VF
driver.
Since the VF driver has not really done anything naughty, let's
not punish it. Don't check for MAC address overrides on the
delete operation, just make sure it's a valid address. This keeps
us from spamming the log with confusing errors.
Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed. Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.
Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where ethtool set-channels would return failure when configuring
only one Rx queue.
Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes make Doxygen/kdoc work correctly without warnings.
Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
The current driver will warn the user if the NVM version
is out of date, this raises the bar to a newer version.
Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit removed any need for these macros, so remove
them too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These instances were found by coccinelle/spatch, and can
use struct assignment instead of memcpy.
Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
o Consider number of Tx queues while calculating the length of
Tx statistics as part of ethtool stats.
o Calculate statistics lenght properly for 82xx and 83xx adapter
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not updating TX stats so it was not populating
statistics in `ifconfig` command output.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 fowarding offload will bypass the rx handler of real device. This will make
the packet could not be forwarded to macvtap device. Another problem is the
dev_hard_start_xmit() called for macvtap does not have any synchronization.
Fix this by forbidding L2 forwarding for macvtap.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
For the mac80211 bits, Johannes says:
"I have a fix from Javier for mac80211_hwsim when used with wmediumd
userspace, and a fix from Felix for buffering in AP mode."
For the NFC bits, Samuel says:
"This pull request only contains one fix for a regression introduced with
commit e29a9e2ae1. Without this fix, we can not establish a p2p link
in target mode. Only initiator mode works."
For the iwlwifi bits, Emmanuel says:
"It only includes new device IDs so it's not vital. If you have a pull
request to net.git anyway, I'd happy to have this in."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x triggers warnings with CONFIG_DMA_API_DEBUG=y:
WARNING: CPU: 0 PID: 2253 at lib/dma-debug.c:887 check_unmap+0xf8/0x920()
bnx2x 0000:28:00.0: DMA-API: device driver frees DMA memory with
different size [device address=0x00000000da2b389e] [map size=1490 bytes]
[unmap size=66 bytes]
The reason is that bnx2x splits a TSO BD into two BDs (headers + data)
using one DMA mapping for both, but it uses only the length of the first
BD when unmapping.
This patch fixes the bug by unmapping the whole length of the two BDs.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch to improve guest receive side flow control (ca2f09f2) had a
slight flaw in the wait condition for the vif thread in that any remaining
skbs in the guest receive side netback internal queue would prevent the
thread from sleeping. An unresponsive frontend can lead to a permanently
non-empty internal queue and thus the thread will spin. In this case the
thread should really sleep until the frontend becomes responsive again.
This patch adds an extra flag to the vif which is set if the shared ring
is full and cleared when skbs are drained into the shared ring. Thus,
if the thread runs, finds the shared ring full and can make no progress the
flag remains set. If the flag remains set then the thread will sleep,
regardless of a non-empty queue, until the next event from the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huqiu reported current sh_sir driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue
Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huqiu reported current sh_irda driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue
Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 80c33dd "net: add might_sleep() call to napi_disable"
bnx2x fails the might_sleep tests causing a stack trace to appear whenever
the driver is unloaded, as local_bh_disable() is being called before
napi_disable().
This changes the locking schematics related to CONFIG_NET_RX_BUSY_POLL,
preventing the need for calling local_bh_disable() and thus eliminating
the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add new AR9565 1.0/1.0.1/1.1 IDs
* Change Dell/Lenovo/Samsung cards to 2-Antenna with diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having two copies of the code for device tree cfgdata
downloading, add a function to improve the code.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfgdata length exceeds the command buffer size we will end up
getting buffer overflow problem. Fix it by checking the buffer
size less the command header length.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the bcm43362 1x1 11n chipset. This
chipset is used in AP6210 wifi module found on Cubieboard [1].
[1] http://cubieboard.org/
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nvs file name to module firmware list
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.
Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware requires a full packet template to be pointed to when adding
hardware flow filters. This patch adds the template and uses it for
programming filters.
Change-ID: I09db9f4ab0207ca9c520ae36596d74e1a0663ae5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some badly formatted lines, long lines and a mis-formatted else.
Change-ID: Iac2eef064ae27c55a0c3d9c15c525bf8fed8ab6f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.
Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
