The WM8903 has four different voltage inputs: AVDD, CPVDD, DBVDD
and DCVDD. On the Qualcomm APQ8060 Dragonboard these are all
supplied from proper regulators and thus need activating and
binding.
This is a quick-and-dirty solution just grabbing and enabling the
regulator supplies on probe() and disabling them on remove() and
the errorpath. More elaborate power management is likely possible.
I assume the nVidia designs using this codec have some hard-wired
always-on power and will be happy with using the dummy regulators
for this. But someone from the nVidia camp should probably check
whether they can bind these to proper regulators instead.
We also amend the DT binding document. A small change like this
does not warrant a separate patch for augmenting these.
Cc: devicetree@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver stashes a CODEC pointer in the cs35l35_private structure,
which is used to obtain a struct device pointer for error messages in the
interrupt handler.
However, doing so is not very safe as the interrupt is registered, as it
should be in bus probe, but the CODEC pointer can't be safely stored until
the ASoC level probe. This leaves a window between the two probes where if
any interrupts are received a NULL pointer will be deferenced in the IRQ
handler.
Fix this issue by saving a pointer to the device directly and passing that
to the error messages in the interrupt handler rather than using the CODEC
pointer to access the device pointer.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple card driver is directly calling priv->snd_card
everywhere, but it makes unreadable code.
Let's use simple_priv_to_card() macro for it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple card driver is directly calling priv->snd_card
everywhere, but it makes unreadable code.
Let's use simple_priv_to_card() macro for it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current asoc_simple_card_probe() already has dev definition,
but some place doesn't use it. Let's fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current asoc_simple_card_probe() already has dev definition,
but some place doesn't use it. Let's fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S2 and I2S3 are share pins. We need to configure it when i2s is
active and disable it when i2s is inactive. To disable i2s pins
means to set them as gpio.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2a3af642eb20("ASoC: rcar: clear DE bit only in PDMACHCR...")
added rsnd_dmapp_bset(), but it used copy-paste. Thus, it had
unnecessary "volatile", and had below warning on x86.
This patch fix it.
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_bset':
>> sound/soc/sh/rcar/dma.c:463:21: warning: passing argument 1 of \
'ioread32' discards 'volatile' qualifier from pointer target \
type [-Wdiscarded-qualifiers]
u32 val = ioread32(addr);
^~~~
In file included from arch/x86/include/asm/io.h:203:0,
from arch/x86/include/asm/realmode.h:5,
from arch/x86/include/asm/acpi.h:33,
from arch/x86/include/asm/fixmap.h:19,
from arch/x86/include/asm/apic.h:10,
from arch/x86/include/asm/smp.h:12,
from include/linux/smp.h:59,
from include/linux/topology.h:33,
from include/linux/gfp.h:8,
from include/linux/idr.h:16,
from include/linux/kernfs.h:14,
from include/linux/sysfs.h:15,
from include/linux/kobject.h:21,
from include/linux/of.h:21,
from include/linux/of_dma.h:16,
from sound/soc/sh/rcar/dma.c:12:
include/asm-generic/iomap.h:31:21: note: expected 'void *' \
but argument is of type 'volatile void *'
extern unsigned int ioread32(void __iomem *);
^~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the driver to use SND_SOC_DAPM_AIF_IN instead of
SND_SOC_DAPM_DAC.
Rename the interface's widgets to be more precise on which slot
the interface is connected.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An unwanted space is present in an audio widget's name on the dapm
routing. It causes an error on the recognition of this widget (error:
("no dapm match for AIF1 Slot 0 Right").
Remove the space fixes it.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner V3s features an analog codec without LINEIN.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner V3s features an analog codec without MIC2.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the ADI AU1761 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected
for ADI blackfin devices or if SND_SOC_ALL_CODECS is enabled.
Signed-off-by: Bryce Ferguson <bryce.ferguson@rockwellcollins.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car datasheet indicates "Clear DE in PDMACHCR" for transfer stop,
but current code clears all bits in PDMACHCR.
Because of this, DE bit might never been cleared,
and it causes CMD overflow. This patch fixes this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
KPB module default parameter were overwritten by the dynamic instance
id once use case is executed. This will cause module crash from
subsequent execution of use case as the updated parameters are used.
So instead of over writing the default parameter, make a copy and
update the module parameter and use this in IPC message.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Kranthikumar, GudishaX <gudishax.kranthikumar@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When module size > DMA buffer size, driver copies first chunk and waits
for the BDL complete interrupt. BDL complete interrupt never occurs and
wait time expires as module load IPC is not send to start the DMA from
DSP.
To fix the above issue need to follow the below steps:
1. After copying the first chunk, send the module load IPC to start the
DMA.
2. Wait for the BDL interrupt. Once interrupt is received, copy the
next chunk.
3. Continue step 2 till all bytes are copied.
4. When all the bytes are copied (bytes_left = 0), wait for module load
IPC response
5. Handled module load IPC response messages, check the load module IPC
response and wake up the thread to complete module load.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dsp ops is already set in init, so use this in cleanup routine
instead of again retrieving it. Also constify struct skl_dsp_ops.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP firmware sends notification every 1ms, which is disabled in runtime
suspend. But if a system has no runtime pm, we keep getting
notification, so disable after FW init as well.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove BE prepare ops which enables MCLK by default. If MCLK is required
to be enabled for any specific platform, it needs to be enabled in the
corresponding machine driver.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If D3 IPC fails or times out, firmware needs to be reloaded as driver
continues the reset.
So set the fw_load flag to false to reload the firmware in D0.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In system suspend, firmware needs to be re-downloaded as IMR is cleared.
When firmware is downloaded in D0, core state is not set to running
state causing instability with subsequent D0-D3 cycles.
So set the core state correctly during D0 and check the DSP core state
if not in reset to set the DSP to D3.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DSP is in D3, no interrupts are expected, so disable
interrupt while entering D3.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the widget is a mixin module, just unbind between source and sink
and don't stop the source pipe as there can be multiple sinks
connected.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP pipe needs to stopped before deleting the pipe. Currently check is
for pipe state > STARTED, which is incorrect. So changed to include
pipe state STARTED to stop the pipe if it started.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_ops structures as const as they are only stored
in the ops field of a snd_soc_dai_link structure. This field is
of type const, so snd_soc_ops structures having this property
can be made const too.
The following .o files did not compile:
sound/soc/fsl/{p1022_rdk.c/p1022_ds.c/mpc8610_hpcd.c}
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_ops structures as const as they are only stored
in the ops field of a snd_soc_dai_link structure. This field is
of type const, so snd_soc_ops structures having this property
can be made const too.
The .o files did not compile for all the changed .c files.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_pll function to codec level and people can use it at both
codec and dai level. Also, lower case "source" to keep it consistent.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs35l35->pdata.stereo is false then "ret" isn't initialized.
Fixes: 6387f866a2 ("ASoC: Add support for Cirrus Logic CS35L35 Amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extraneous tab to correct the nesting level indentation
Detected by CoverityScan, CID#1416584 ("Nesting level does
not match indentation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure this machine driver is only used if enabled explicitly
and if there is no information found in the SSDT.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add card with dummy codec and DAI to make I2S signals observable.
Uses Mic and Speaker pins/widgets to control DAPM
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add entries in HID table and reference to bytcht_da7213 driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new machine driver, tested with Ard-Audio-DA7212 [1]
connected to MinnowBoardMAX Turbot.
The MCLK is managed by the codec driver using the "mclk" handle
to reuse existing code, but it could just as well be handled
by this machine driver.
[1] http://www.dialog-semiconductor.com/content/ard-audio-da7212
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As it is quite common to use a stereo pair of amps but share the IRQ
line between them both add the IRQF_SHARED flag whilst requesting
cs35l35's IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidy up the code a little by adding a local variable for i2c_client->dev
rather than referring to it explicitly everytime.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting how the I2S pins are driven in unused slots,
currently the chip will just use the default of drive 0, however this
causes issues when multiple devices are attached to the same bus.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A return statement is missing just before the error paths at the end of
probe. This causes us to fall straight into the error path and disable
the supplies and re-enable reset, as these are only controlled during
probe this causes the part to no longer function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a commit 4cd9899f0d ("ASoC: Intel: Skylake: Add multiple pin
formats") describes, 'fixups is applied to pin 0 only'. On the other
hand, the commit left some codes as what they were. This might
confuses readers.
This commit fixes the issue. This doesn't change driver behaviour at all.
Fixes: 4cd9899f0d ("ASoC: Intel: Skylake: Add multiple pin formats")
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the problem that the missing value of the route path
setting table and incorrect values are set in the CMD_ROUTE_SELECT
register.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
[Kuninori: shared data on MIX and non-MIX case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all platform drivers have pcm_{new,free} callbacks. Seen with a
"snd-soc-dummy" codec from sound/soc/rockchip/rk3399_gru_sound.c.
Fixes: 99b04f4c40 ("ASoC: add Component level pcm_new/pcm_free")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SOC_MIXER_ARRAY is a simplified function of SND_SOC_DAPM_MIXER
which handles automatically the ARRAY_SIZE of controls.
Update the driver to use SOC_MIXER_ARRAY.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the driver to use the new SOC_DAPM_DOUBLE definition
on the digital DAC mixer.
Update the names accordingly as, when they are shared, the
controls are not prefixed with the widget's name anymore.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "HP" widget is already present and take part to
the analog part (sun8i-codec-analog).
Remove it from the digital part as it is unnecessary.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use manual mode for jack detection function to increase accuracy.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM is necessary for more than 2 channels. And there is no control bit
to specify which slots are using. Machine driver will not need to call
snd_soc_dai_set_tdm_slot if we do it in rt5665_hw_params.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vref3 is necessary for Mono Amp. So add it to dapm routes
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We got rt5665 private data from wrong work. It will result in kernel
panic.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This was reported by checkpatch.pl
Signed-off-by: Alin Grigorean <alin.grig93@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 'include/linux/kernel.h', there's a helper macro to round numerical
value. Let's use it.
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic snd_dmaengine_pcm is able to retrieve all the needed
information from the attached dmaengine and is in fact able to
provide much more accurate flags to userspace, like the SDMA engine
being only able to operate in batch mode.
To avoid any future inconsistencies between the dmaengine and the
pcm_config, rip out the fixed config and rely on the core to fill
in the right flags derived from the dmaengine information.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the audio clock rate according to the datasheet.
Reported-by: Dushara Jayasinghe <dushara@successful.com.au>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In 'skl_tplg_set_module_init_data()', a pointer to 'params' member of
'struct skl_algo_data' is calculated, then casted to (u32 *) and assigned
to a member of configuration data. The configuration data is passed to the
other functions and used to process intel IPC. In this processing, the
value of member is used to get message data, however this can bring invalid
memory access in 'skl_set_module_params()' as a result of calculation of
a pointer for actual message data.
(sound/soc/intel/skylake/skl-topology.c)
skl_tplg_init_pipe_modules()
->skl_tplg_set_module_init_data() (has this bug)
->skl_tplg_set_module_params()
(sound/soc/intel/skylake/skl-messages.c)
->skl_set_module_params()
((char *)param) + data_offset
This commit fixes the bug.
Fixes: abb740033b ("ASoC: Intel: Skylake: Add support to configure module params")
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # v4.5+
Use the "cansleep" variant of gpiod_set_value so the driver can be used
with slow gpio controllers as well.
Fixes: 85825d5e88 ("ASoC: dio2125: add dio2125 amp driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was reported by checkpatch.pl
Signed-off-by: Codrut Grosu <codrut.cristian.grosu@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was reported by checkpatch.pl
Signed-off-by: Codrut GROSU <codrut.cristian.grosu@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Out of memory message detected using checkpatch.pl
Signed-off-by: Adriana Constantinescu <constantinescu33@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was reported by checkpatch.pl
Signed-off-by: Codrut GROSU <codrut.cristian.grosu@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During S3->S0 transition, sometime ROM init fails because of
authentication engine loads later than the OS. In this case driver
waits for a longer period and then retries the FW download causing
huge delay in resume time of audio device.
To avoid this, ROM INIT wait time is set to a optimal value and
increased the retries for firmware download.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the DSP firmware/library at boot, so that for S3 to S0 transition
use the stored ctx for downloading the firmware to DSP memory.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since index is always 0 replace devm_gpiod_get_index() by devm_gpiod_get()
and apply proper flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is a stereo output driver with adjustable gain.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not be writing acknowledge controls until the firmware is
running, as in the case of preloaded firmwares the DSP memory may be
unaccessible to whilst in the preloaded state. This means a write to the
control during this time could be lost.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Volatile controls should only be accessed when the firmware is active,
currently however writes to these controls will succeed, but the data
will be lost, if the firmware is powered down. Update this behaviour such
that an error is returned the same as it is for reads.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es7134 is 24bit, 192Khz i2s DA converter for PCM audio.
Datasheet is available here : http://www.everest-semi.com/pdf/ES7134LV%20DS.pdf
This driver is also compatible with the es7144, which is the same as the
es7134, with 2 additional pins for filtering capacitors.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform is completely probed by device tree nowadays, so
we need to do a bigger cleanup removing all the non-DT codepaths.
This cleanup must however go in as a fix since it fixes a
regression.
Currently when Ux500 audio is enabled, dmesg complains like
this:
entry->name == "prealloc"
entry->name == "prealloc_max"
entry->name == "prealloc"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc' already registered
(...)
entry->name == "prealloc_max"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc_max' already registered
(...)
snd-soc-mop500 soc🔉 ab8500-codec-dai.0 <->
80124000.msp mapping ok
entry->name == "prealloc"
entry->name == "prealloc_max"
entry->name == "prealloc"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc' already registered
(...)
entry->name == "prealloc_max"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc_max' already registered
snd-soc-mop500 soc🔉 ab8500-codec-dai.1 <->
80125000.msp mapping ok
This is because PCMs are created twice for the same hardware,
and this happens because both "platform" and "CPU" DAI links
are specified.
But platform/CPU is an either/or pair, not a both/and pair.
This has maybe worked in the past, but it is causing trouble
now, so let us begin the cleanups by removing the platform
assignment and silencing the boot noise, and make a proper DT
cleanup for the next kernel cycle.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix not to update the iterator element, instead use list_del to remove
entry from the list.
This fixes the following coccinelle and static checker warning:
sound/soc/codecs/hdac_hdmi.c:1884:2-21:iterator with update on line
1885
sound/soc/codecs/hdac_hdmi.c:2011 hdac_hdmi_dev_remove()
error: potential NULL dereference 'port'.
Fixes: e0e5d3e5a53b('ASoC: hdac_hdmi: Add support for multiple ports to a PCM')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pin list array iterator outside the iteration of the list can
point to dummy element, which can be invalid. So don't use pin variable
outside the pin list iteration.
This fixes the following coccinelle warning:
sound/soc/codecs/hdac_hdmi.c:1419:5-8: ERROR: invalid reference to the
index variable of the iterator
Fixes: 2acd8309a3a4('ASoC: hdac_hdmi: Add support to handle MST capable pin')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without this I am getting the following messages at boot on my Trimslice:
tlv320aic23-codec 2-001a: Control not supported for path LLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for LLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route LLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path RLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for RLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route RLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path MICIN -> [NULL] -> Mic Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for MICIN --> NULL --> Mic Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route MICIN -> NULL -> Mic Input
tegra-snd-trimslice sound: tlv320aic23-hifi <-> 70002800.i2s mapping ok
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the sampling frequency is supported by es8328 in slave mode,
add support for it in the corresponding operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the sampling frequency is supported by es8328 in slave mode,
add support for it in the corresponding operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The master and slave modes don't share the same table for MCLK/LRCLK
ratios. The slaves mode has bigger ratios that allow to use BCLK that
matche sampling frequency of 192khz.
This commit enables this rate only for slave mode, i.e it does not
declare this frequency in sysclk_contraints, resulting to an error in
master mode (not supported CLK).
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently most of the standard rates are supported by this driver.
Instead of defining each supported rate one by one, we use the SND macro
SNDRV_PCM_RATE_8000_48000. Also adds support for 88.2khz as the codec
supports it and the sys clocks are already supported.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In master mode, SCLK and LRCLK signals are generated by the CODEC when
any of the ADC/DAC are enabled. SCLK is derived from MCLK via a
programmable division set by BLK_DIV, LRCLK is derived from MCLK via
another programmable division set by ADCFsRatio/DACFsRatio.
In slave mode, SCLK and LRCLK signals are received as inputs and
supplied externally. LRCLK and SCLK must be synchronously derived from
MCLK with specific rates. The device can auto detect MCLK/LRCLK ratio
according to a predefined table. LRCLK/SCLK ratio is usually 64 (SCLK =
64 * LRCLK)
This commits adds support to let to device auto detect and decide which
ratio to use. The mclkdiv2 and BCLK_DIV ratio and put to zero.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI8 is is sharing pin with SSI7, and nothing to do for SSI_MODEx.
It is special pin and it needs special settings whole system,
but we can't confirm it, because we never have SSI8 available board.
This patch fixup SSI_MODEx settings error for SSI8 on connection test,
but should be confirmed behavior on real board in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
deintializing||deinitializing
deintialize||deinitialize
deintialized||deinitialized
Link: http://lkml.kernel.org/r/1481573103-11329-28-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
unneded||unneeded
Link: http://lkml.kernel.org/r/1481573103-11329-15-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should not select drivers that depend on I2C when that is disabled,
as it results in a build error:
warning: (SND_SOC_MT2701_CS42448) selects SND_SOC_CS42XX8_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && I2C)
sound/soc/codecs/cs42xx8-i2c.c:60:1: warning: data definition has no type or storage class
module_i2c_driver(cs42xx8_i2c_driver);
sound/soc/codecs/cs42xx8-i2c.c:60:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
Fixes: 1f458d53f7 ("ASoC: mediatek: Add mt2701-cs42448 driver and config option.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, this function cannot fail for the ADG case. Still, let's
apply defensive programming techniques to make sure we fail gracefully
whenever rsnd_mod_init() gets extended with another failure case.
Reported by Coverity (CID 1397893).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Coverity reported (CID 1397992) this self-assignment. I think the code
stays readable even with the assignments removed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not necessary to unregister a component registered
with devm_snd_soc_register_component(). Also removed
pointness clk_disable_unprepare() from error path and
snd_soc_unregister_platform() from the remove.
Fixes: f8260afa44 ("ASoC: sunxi: Add support for the SPDIF block")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
configurable LRC and BCLK divide. The driver
will make configurations of LRC and BCLK automatically according to
BCLK and FS information in master mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is new Intel SoC, so add codec entry for HDMI
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is next gen SoC, so add the IDs for Geminilake.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake has two different devices connected to the same SSP, so use
device_type check to get correct device configuration.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Represent each port as machine DAPM pin widget. This helps in
enable/disable pin when monitor is connected/disconnected in case pcm
is rendered to multiple ports.
Create machine pin widgets and pin switch kcontrol for each port and
report based on the pin status
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in bxt_da7219_max98357 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in bxt_rt298.c machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in skl_nau88l25_ssm4567 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in skl_nau88l25_max98357a machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI pcm and calls hdmi codec API to initialize
jack in skl_rt268 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_jack instead of snd_jack and create the jack in machine
driver and pass the jack pointer to hdac_hdmi driver for jack
reporting.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have the MST feature enabled and Pin-Port mux for user to
select the converter routing, multiple port mapping to same converter
needs to be supported.
To support multiple port mapped to same converter following changes are
done for this:.
o Add port list to pcm, so that multiple ports can be mapped to a PCM.
o Jack reporting in case where multiple port are attached to same PCM.
o Change hdac_hdmi_get_port_from_cvt(), channel_map, remove functions
to parse through all ports mapped to same the PCM.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable stream on a specific port of a MST capable pin, the port
needs to be selected before we configure the pin widget verb.
When port is selected, all the pin widget verb controlling the sink
device operation will be directed to selected port. So add port
selection before configuring the pin widget verb.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ELD notification can be received asynchronously from the graphics
side and this may happen just at the moment the sound driver is
initializing and notification will be missed. Similarly at system
resume, the notification is ignored as the ELD and connection states
are updated in anyway at the end of the resume.
So check the jack status in boot/resume by querying the port presence
based on pin caps and report the jack status.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support DP MST audio, new pin verbs/params are added. This patch
adds helper functions to do following:
o To set a specific port
o To get the currently selected port
o To get the length of port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FSL SAI can support up to 32 channels using TDM. Report that value so
they can actually be used.
Tested using 8 channels.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pclk is necessary for zx2967 I2S controller. the driver
currently doesn't handle it. This is something we need to fix.
In turn, the driver supports zx296718's I2S controller.
By the way, this patch also change the clock name from tx to wclk
to make it clear.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
While unregistering the hdmi-codec, the hdmi device list must be
cleaned up. It avoid kernel page fault when registering again the
hdmi-codec.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle jack event and configuration of the pin widget for MST
capable pin, this patch adds:
o Flag to identify the pin is MST capable.
o In notify callback(), based on the pipe and port information marks if
the port is mst_capable. In case of non MST, port is defaulted to zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in nau88l25_ssm4567 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in nau88l25_max98357a machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in bxt_rt298 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With MST each pin contains several ports to which device can be
connected.
As a preparatory work to support DP MST this patch adds below changes:
1. Defines the port structure and moves all stream related information
like ELD, converter list, chmap to port.
2. Creates ports for each pin based on the max_ports support.
3. Based on Pin-Port combination creates DAPM Mux widget instead of Pin
to allow user to select a converter.
4. Port zero is the default port when pin does not support MST.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two front-ends to the codec can now be selected individually, but fail to
build when the bus support is missing:
sound/built-in.o: In function `es8328_spi_probe':
es8328-spi.c:(.text+0x125854): undefined reference to `__devm_regmap_init_spi'
sound/built-in.o: In function `es8328_spi_driver_init':
es8328-spi.c:(.init.text+0x3589): undefined reference to `__spi_register_driver'
Related to this, the added dependency on SND_SOC_ES8328 breaks:
warning: (SND_SOC_ALL_CODECS) selects SND_SOC_ES8328_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_ES8328 && I2C)
This adds the respective Kconfig dependencies and changes SND_SOC_ES8328 to a hidden
symbol that is selected implicitly by the two more specific options, as we do for
some other codecs. We have to remove the 'depends on' for SND_SOC_IMX_ES8328 in the
same step to avoid a recursive dependency.
Fixes: aa00f2c8af ("ASoC: Allow to select ES8328_I2C and ES8328_SPI directly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch create entry in sysfs file system to report the
platform_id = "pci-id-oem_id-oem_table_id-oem_revision"
for board identification.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is used for Rockchip rk3288-based boards using a configurable
analog output (can be an headphone) and the built-in HDMI audio output
that is part of the RK3288 SoCs and use the Alsa HDMI codec driver. For
some rk3288-based boards the analog output and the hdmi audio are plugged
on the same i2s line, so we have to do the same in the driver by using a
DAI link CPU to multicodecs. This configuration can be found for example
on the Radxa Rock2 or the Firefly-RK3288.
This commit is based on the initial work that was done by Sjoerd Simons
<sjoerd.simons@collabora.com> with some improvements.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we have to select these symbols explictly via Kconfig, from
another entry. If we plan to use generic audio drivers like
simple-audio-card, the user need to be able to enable these symbols
directly via the menuconfig.
This commit also fixes unmet dependencies to SND_SOC_IMX_ES8328 caused
by these changes.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the function that changes the DAI format only supports master
mode. Trying to use a slave mode exits the function with -EINVAL and
leave the codec misconfigured. This commits adds support for enabling
the slave mode.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in bxt_da7219_max98357a machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in skl_rt286 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per pcm. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which registers
channel map in the late probe callback handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel info is part of the pcm parameter and channel map control is
created for each pcm. So move channel info to pcm instead of pin
structure and the mutex lock to pcm.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a relict of 6553bf06a3 ("ASoC: Don't try to register debugfs
entries if the parent does not exist").
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SoCs have a reset line that must be asserted/deasserted.
This patch adds a quirk to handle the new compatible
"allwinner,sun6i-a31-i2s" which will deassert the reset
line on probe function and assert it on remove's one.
This new compatible is useful in case of A33 codec driver, for example.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the sun8i audio codec which handles the digital register of
A33 codec.
The driver handles only the basic playback from the DAC to headphones.
All other features (microphone, capture, etc) will be added later.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When playing a sound for the first time, a short delay, where the audio
file is not played, can be noticed.
On a second play (right after), the sound is played correctly.
If we wait a short time (~5 sec which corresponds to the aplay
timeout), the delay is back.
This patch fixes it by using an event on headphone amplifier.
It allows to keep the amplifier enable while playing a sound.
A delay of 700ms allows to wait that the amplifier is powered-up
before playing the sound.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sync convert rate settings should be availabled *after* Playing.
Thus, src->sync should be reset first of init function.
Otherwise, it will set remaining settings when it start playing.
This patch fixes it. Thanks to Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Missed unused variable in previous changes, oops.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Optional gpio handling should not cause an error status and prevent
probing if it's missing. Remove error return for -ENOENT case and
move error message to dev_info
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can get audio errors if hitting deeper idle states on omaps:
[alsa.c:230] error: Fatal problem with alsa output, error -5.
[audio.c:614] error: Error in writing audio (Input/output error?)!
This seems to happen with off mode idle enabled as power for the
whole SoC may get cut off between filling the McBSP fifo using DMA.
While active DMA blocks deeper idle states in hardware, McBSP
activity does not seem to do so.
Basing the QoS latency calculation on the FIFO size, threshold,
sample rate, and channels.
Based on the original patch by Tony Lindgren
Link: https://patchwork.kernel.org/patch/9305867/
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The combination of dev_err() and __func__ make most of these log prints
over 100 chars long. Remove the usage of __func__ to clean the kernel
log and as the usage is not necessary to identify the individual log
prints.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the clock calling code by removing numerous IS_ERR() checks by
just assigning the clock NULL; as this turn all used functions in the
clk API to nops.
Also include the word "optional" in the error message when failing to acquire
the optional osr clocks.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This macro is unused since commit e369bd006f ("ASoC: wm8741: Allow master
clock switching").
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_card_jack_new function can call snd_soc_jack_add_pins for
you, so pass directly the pins struct when you create the new jack.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove default and set I2S mode correctly both on codec and
cpu sides
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use ACPI ID 10EC3270 to load machine driver for cht-bsw-rt5645
and add reference to 3270 to use the rt5645 mode
Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some platforms use AIF2, use routing information to set ASRC as needed
Suggested-by: Bard Liao <bardliao@realtek.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver may be used on Baytrail CR platforms where SSP2 is
not available.
Add quirks and routing detection based on work done for RT5640.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALC3270 is a low-cost version of RT5645, add ACPI ID
to enable probe and use rt5645 codec driver
Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the BIOS reports this codec as RT5640 but it's a rt5670. Use the
quirk mechanism to use the cht_bsw_rt5672 machine driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix classic issue of having multiple codecs listed in DSDT
but a single one actually enabled. The previous code did
not handle such errors and could also lead to uninitalized
configurations
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use machine driver initially defined for CherryTrail
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add ACPI ID 10EC5648 found e.g on Asus X205TA and use
rt5645 driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the BIOS incorrectly reports this codec as 5640 but it is
really a rt5670
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5651 is used on some Cherrytrail platforms, add the ACPI
ID in machine table.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=156191
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine entry for HP X2 Pavilion 10-p100.
This notebook contains rt5640 codec, but with ACPI ID "10EC3276".
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ACPI ID "10EC3276" for sound card found on notebook HP Pavilion X2 10-p000.
ACPI DSDT Table on this device describes this card as ALC3276, but it is in fact rt5640.
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing code assumes a 19.2 MHz MCLK as the default
hardware configuration. This is valid for CherryTrail but
not for Baytrail.
Add explicit MCLK configuration to set the 19.2 clock on/off
depending on DAPM events.
This is a prerequisite step to enable devices with Baytrail
and RT5645 such as Asus X205TA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current frame sync polarity definitions are inconsistent in the
Atom/DPCM driver, fix to align with regular ASoC definitions and
update code in platform and machine drivers for RT5640 and RT5651.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
