Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
"VLAN" type, whereas RIFs constructed on top of VLAN-unaware bridges of
"FID" type.
In other words, the RIF type is derived from the underlying FID type.
VLAN RIFs are used on top of 802.1Q FIDs, whereas FID RIFs are used on
top of 802.1D FIDs.
Since the previous patch emulated 802.1Q FIDs using 802.1D FIDs, this
patch emulates VLAN RIFs using FID RIFs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses 802.1Q FIDs when offloading a VLAN-aware bridge.
Unfortunately, it is not possible to assign a VNI to such FIDs, which
prompts the driver to forbid the enslavement of VxLAN devices to a
VLAN-aware bridge.
Workaround this hardware limitation by creating a new family of FIDs,
emulated 802.1Q FIDs. These FIDs are emulated using 802.1D FIDs, which
can be assigned a VNI.
The downside of this approach is that multiple {Port, VID}->FID entries
are required, whereas only a single VID->FID is required with "true"
802.1Q FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1D FIDs use a per-FID flood table, where the flood index into the
table is calculated by subtracting 4K from the FID's index.
Currently, 802.1D FIDs start at 4K, so the calculation is correct, but
if it was ever to change, the calculation will no longer be correct.
In addition, this change will allow us to reuse the flood index
calculation function in the next patch, where we are going to emulate
802.1Q FIDs using 802.1D FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring an FDB entry pointing to a LAG netdev (or its upper),
the driver should only set the 'lag_vid' field when the FID (filtering
identifier) is of 802.1D type.
Extend the 802.1D FID family with an attribute indicating whether this
field should be set and based on its value set the field or leave it
blank.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:260:7:
warning: variable 'err' set but not used [-Wunused-but-set-variable]
'err' should be returned while set MPI_DEINIT state fails
in hw_atl_utils_soft_reset.
Fixes: cce96d1883 ("net: aquantia: Regression on reset with 1.x firmware")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.
The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that synchronize_rcu() waits for preempt-disable regions of code
as well as RCU read-side critical sections, synchronize_sched() can be
replaced by synchronize_rcu(). This commit therefore makes this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Now that synchronize_rcu() waits for preempt-disable regions of code
as well as RCU read-side critical sections, synchronize_sched() can be
replaced by synchronize_rcu(). This commit therefore makes this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Register a separate handler per event type, rather than listening for all
events and looking for the events to handle in a switch case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move all the generic async events handling into new specific events
handling file events.c to keep eq.c file clean from concrete event logic
handling.
Use new API to register for NOTIFY_ANY to handle generic events and
dispatch allowed events to mlx5_core consumers (mlx5_ib and mlx5e)
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_eq_cq_event on MLX5_EVENT_TYPE_CQ_ERROR
and register a specific CQ ERROR handler via the new API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to QP/SRQ resources events handlers on several FW
events and let resources logic register resources events notifiers via the
new API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_cmd_comp_handler on MLX5_EVENT_TYPE_CMD
and let command interface to register its own handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_core_req_pages_handler on
MLX5_EVENT_TYPE_PAGE_REQUEST and let FW page logic to register its own
handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_eswitch_vport_event on
MLX5_EVENT_TYPE_NIC_VPORT_CHANGE and let the eswitch register its own
handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_pps_event on MLX5_EVENT_TYPE_PPS_EVENT
and let clock logic to register its own handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_fpga_event on
MLX5_EVENT_TYPE_FPGA_ERROR or MLX5_EVENT_TYPE_FPGA_QP_ERROR
let fpga core to register its own handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_fw_tracer_event on
MLX5_EVENT_TYPE_DEVICE_TRACER and let fw tracer to register
its own handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use atomic_notifier_chain to fire firmware events at internal mlx5 core
components such as eswitch/fpga/clock/FW tracer/etc.., this is to
avoid explicit calls from low level mlx5_core to upper components and to
simplify the mlx5_core API for future developments.
Simply provide register/unregister notifiers API and call the notifier
chain on firmware async events.
Example: to subscribe to a FW event:
struct mlx5_nb port_event;
MLX5_NB_INIT(&port_event, port_event_handler, PORT_CHANGE);
mlx5_eq_notifier_register(mdev, &port_event);
where:
- port_event_handler is the notifier block callback.
- PORT_EVENT is the suffix of MLX5_EVENT_TYPE_PORT_CHANGE.
The above will guarantee that port_event_handler will receive all FW
events of the type MLX5_EVENT_TYPE_PORT_CHANGE.
To receive all FW/HW events one can subscribe to
MLX5_EVENT_TYPE_NOTIFY_ANY.
The next few patches will start moving all mlx5 core components to use
this new API and cleanup mlx5_eq_async_int misx handler from component
explicit calls and specific logic.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-11-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Extend BTF to support function call types and improve the BPF
symbol handling with this info for kallsyms and bpftool program
dump to make debugging easier, from Martin and Yonghong.
2) Optimize LPM lookups by making longest_prefix_match() handle
multiple bytes at a time, from Eric.
3) Adds support for loading and attaching flow dissector BPF progs
from bpftool, from Stanislav.
4) Extend the sk_lookup() helper to be supported from XDP, from Nitin.
5) Enable verifier to support narrow context loads with offset > 0
to adapt to LLVM code generation (currently only offset of 0 was
supported). Add test cases as well, from Andrey.
6) Simplify passing device functions for offloaded BPF progs by
adding callbacks to bpf_prog_offload_ops instead of ndo_bpf.
Also convert nfp and netdevsim to make use of them, from Quentin.
7) Add support for sock_ops based BPF programs to send events to
the perf ring-buffer through perf_event_output helper, from
Sowmini and Daniel.
8) Add read / write support for skb->tstamp from tc BPF and cg BPF
programs to allow for supporting rate-limiting in EDT qdiscs
like fq from BPF side, from Vlad.
9) Extend libbpf API to support map in map types and add test cases
for it as well to BPF kselftests, from Nikita.
10) Account the maximum packet offset accessed by a BPF program in
the verifier and use it for optimizing nfp JIT, from Jiong.
11) Fix error handling regarding kprobe_events in BPF sample loader,
from Daniel T.
12) Add support for queue and stack map type in bpftool, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of xmit_more and add the functionality introduced with
3e59020abf ("net: bql: add __netdev_tx_sent_queue()").
I used the mlx4 driver as template.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dev is dereferenced by the call dev_net(dev) before dev is null
checked. Fix this by null checking dev before the potential null
pointer dereference.
Detected by CoverityScan, CID#1462955 ("Dereference before null check")
Fixes: 23790ef120 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5883:6:
warning: variable 'multitrc' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:8585:32:
warning: variable 'speed' set but not used [-Wunused-but-set-variable]
'multitrc' never used since introduction in
commit 8e3d04fd7d ("cxgb4: Add MPS tracing support")
'speed' never used since introduction in
commit c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX stats should be started with the tx_stats_syncp,
there seems to be a copy/paste error in the driver.
Signed-off-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.
phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.
Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.
Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an explicit check in rocker_world_port_obj_vlan_add(),
dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects
that are added to a device that is not a front-panel port device are
ignored. Therefore this check is immaterial.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of
this field from all clients, which were migrated to use switchdev
notification in the previous patches.
Add a new function switchdev_port_obj_notify() that sends the switchdev
notifications SWITCHDEV_PORT_OBJ_ADD and _DEL.
Update switchdev_port_obj_del_now() to dispatch to this new function.
Drop __switchdev_port_obj_add() and update switchdev_port_obj_add()
likewise.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
Dispatch the new events to ocelot_port_obj_add() resp. _del() to
maintain the same behavior that the switchdev operation based code
currently has. Pass through switchdev_handle_port_obj_add() / _del() to
handle the recursive descend, because Ocelot supports LAG uppers.
Register to the new switchdev blocking notifier chain to get the new
events when they start getting distributed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to mlxsw_sp_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has. Defer to switchdev_handle_port_obj_add() / _del() to handle the
recursive descend, because mlxsw supports a number of upper types.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
rocker currently doesn't support any uppers other than bridge. Thus the
only case that a stacked device could be validly referenced by port
object notifications are bridge notifications for VLAN objects added to
the bridge itself. But the driver explicitly rejects such notifications
in rocker_world_port_obj_vlan_add(). It is therefore safe to assume that
the only interesting case is that the notification is on a front-panel
port netdevice.
Subscribe to the blocking notifier chain. In the handler, filter out
notifications on any foreign netdevices. Dispatch the new notifiers to
rocker_port_obj_add() resp. _del() to maintain the behavior that the
switchdev operation based code currently has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace macro TX_FRAGS_READY_FOR with function rtl_tx_slots_avail
to make code cleaner and type-safe.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_consume_skb() where possible to profit from
bulk free infrastructure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the GMII chip versions we set the version number which was set
already. This can be simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even the chip versions within a family have so many differences that
using a default chip version doesn't really make sense. Instead
of leaving a best case flaky network connectivity, bail out and
report the unknown chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ancient GCC bug workaround in a second place and factor out
rtl_8169_get_txd_opts1.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the queue information of the current NIC
such as BD size, queue header and tail pointer.
This patch adds support for debugfs command:
echo queue info 1 > cmd
it can print queue config information...
root@(none)# echo queue info 1 > cmd
hns3 0000:7d:00.0: queue info
hns3 0000:7d:00.0: RX(1) BASE ADD: 0x00000000ffb58000
hns3 0000:7d:00.0: RX(1) RING BD NUM: 127
hns3 0000:7d:00.0: RX(1) RING BD LEN: 2
hns3 0000:7d:00.0: RX(1) RING TAIL: 120
hns3 0000:7d:00.0: RX(1) RING HEAD: 0
hns3 0000:7d:00.0: RX(1) RING FBDNUM: 0
hns3 0000:7d:00.0: RX(1) RING PKTNUM: 0
hns3 0000:7d:00.0: TX(1) BASE ADD: 0x00000000fffd8000
hns3 0000:7d:00.0: TX(1) RING BD NUM: 127
hns3 0000:7d:00.0: TX(1) RING TC: 0
hns3 0000:7d:00.0: TX(1) RING TAIL: 2
hns3 0000:7d:00.0: TX(1) RING HEAD: 2
hns3 0000:7d:00.0: TX(1) RING FBDNUM: 0
hns3 0000:7d:00.0: TX(1) RING OFFSET: 0
hns3 0000:7d:00.0: TX(1) RING PKTNUM: 0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the debugfs framework to the driver and create a debugfs
command interface for each device.
example command:
"echo queue info > cmd" Query the packet forwarding queue information.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ptp_clock_register never return NULL, so no need check this
in cavium_ptp_probe.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added new CGX firmware interface API for sending link up/down
commands
- Do link up for cgx lmac ports by default at the time of CGX
driver probe. Since cgx link up in driver probe affects the
Linux boot time, linkup procedure is kept threaded using
workqueues.
For this, a new cgx API cgx_lmac_linkup_start has been added.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
