Since we merged runtime PM support for DPMS, it is possible that these
assertions will be called when the power wells are disabled but a mode
is "set", resulting in "failed assertion" and "device suspended while
reading register" WARNs.
To reproduce the bug: disable all screens using mode unset, do a
modeset on one screen, disable it using DPMS, then try to do a mode
unset on it again to see the WARNs.
v2: The first version of this patch changed the assertions to also
check the power domains. Daniel suggested that it would be better to
just remove the assertions: "The modeset state checker
will already notice when we've failed to turn off the pipe. And we
check cursors and plane state in the enable sequence, too. Since we
use these asserts a lot to lock down the precise modeset sequence I
actually prefer if they're a bit dumb and don't check the power
wells."
Testcase: igt/rpm_rpm/dpms-mode-unset-lpsp
Testcase: igt/rpm_rpm/dpms-mode-unset-non-lpsp
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we use the runtime IRQ enable/disable functions in our suspend
path, we can simply check the pm._irqs_disabled flag everywhere. So
rename it to catch the users, and add an inline for it to make the
checks clear everywhere.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't write it, otherwise we will trigger unclaimed register
errors.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, after i915_pm_suspend display power wells are staying
power ungated. So, after initiating mem sleep "echo mem > /sys/power/state"
Display is staing D0 State. There might be better way/place to power gate
these wells. Also, we need to make sure that if wells are power gated due to
DPMS OFF sequence, they need not be turned off by i915_pm_suspend again.
v2: Extracted helper for intel_crtc_disable and power gating CRTC power wells.
[Daniel]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Change-Id: I34c80da66aa24c423a5576c68aa1f3a8d0f43848
Signed-off-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DP MST will need connectors that aren't connected to specific
encoders, add some checks in advance to avoid oopses.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc improvements when stolen memory is tight (Ben)
- cdclk handling improvements for vlv/chv (Ville)
- proper fix for stuck primary planes on gmch platforms with cxsr (Imre&Ebgert
Eich)
- gen8 hw semaphore support (Ben)
- more execlist prep work from Oscar Mateo
- locking fixes for primary planes (Matt Roper)
- code rework to support runtime pm for dpms on hsw/bdw (Paulo, Imre & me), but
not yet enabled because some fixes from Paulo haven't made the cut
- more gpu boost tuning from Chris
- as usual piles of little things all over
* tag 'drm-intel-next-2014-07-11' of git://anongit.freedesktop.org/drm-intel: (93 commits)
drm/i915: Make the RPS interrupt generation mask handle the vlv wa
drm/i915: Move RPS evaluation interval counters to i915->rps
drm/i915: Don't cast a pointer to void* unnecessarily
drm/i915: don't read LVDS regs at compute_config time
drm/i915: check the power domains in intel_lvds_get_hw_state()
drm/i915: check the power domains in ironlake_get_pipe_config()
drm/i915: don't skip shared DPLL assertion on LPT
drm/i915: Only touch WRPLL hw state in enable/disable hooks
drm/i915: Switch to common shared dpll framework for WRPLLs
drm/i915: ->enable hook for WRPLLs
drm/i915: ->disable hook for WRPLLs
drm/i915: State readout support for WRPLLs
drm/i915: add POWER_DOMAIN_PLLS
drm/i915: Document that the pll->mode_set hook is optional
drm/i915: Basic shared dpll support for WRPLLs
drm/i915: Precompute static ddi_pll_sel values in encoders
drm/i915: BDW also has special-purpose DP DDI clocks
drm/i915: State readout and cross-checking for ddi_pll_sel
drm/i915: Move ddi_pll_sel into the pipe config
drm/i915: Add a debugfs file for the shared dpll state
...
commit 98ec77397a
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Apr 30 17:43:01 2014 +0300
drm/i915: Make primary_enabled match the actual hardware state
introduced more accurate tracking of the primary plane and some
checks. It missed the plane->pipe reassignement code for gen2/3
though, which the checks caught and resulted in WARNING backtraces.
Since we only use this path if the plane is on and on the wrong pipe
we can just always set the tracking bit to "enabled".
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
drm/i915: do not setup backlight if not available according to VBT
caused a regression on the HP Chromebook 14 (with Celeron 2955U CPU),
which has a misconfigured VBT. Apply quirk to ignore the VBT backlight
presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Stefan Nagy <public@stefan-nagy.at>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV and CHV disable the DP port only in the .post_disable() hook, so we
need to make intel_sanitize_encoder() call that when it's trying to
disable encoders without an active pipes.
My bsw actaully hits this when an external display is connected. The
BIOS still likes to turn on the eDP port, but leaves the pipe disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Remove now bogus comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we already do in haswell_get_pipe_config(). This should
prevent some WARNs when we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we now have support for shared DPLLS.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be able to do this we need to separately keep track of how many
crtcs need a given WRPLL and how many actually actively use it. The
common shared dpll framework already has all this, including massive
state readout and cross checking. Which allows us to do this switch in
a fairly small patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently still with a redudant WARN_ON in there, the common shared
dpll code will take care of this in the future.
Also we need to flip the switch for the transitional hack now to make
sure that we disable the right pll.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still tacked onto the side, but slowly getting there.
v2: Don't forget the debugfs file.
v3 (from Paulo): Don't forget to check the power domains.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And get/put it when needed. The special thing about this commit is
that it will now return false in ibx_pch_dpll_get_hw_state() in case
the power domain is not enabled. This will fix some WARNs we have when
we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla:https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just filing in names and ids, but not yet officially registering them
so that the hw state cross checker doesn't completely freak out about
them. Still since we do already read out and cross check
config->shared_dpll the basics are now there to flesh out the wrpll
shared dpll implementation.
The idea is now to roll out all the callbacks step-by-step and then at
the end switch to the shared dpll framework. This way hw and sw
changes are clearly separated.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: added const to hsw_ddi_pll_names (Damien)]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.
We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.
Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.
v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL disabling
into the post_disable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT post_disable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL enabling
into the pre_enable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT pre_enable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the other checks also check hw state, so checking our software
refcounts for the plls looks a bit odd. Also this will simplify the
conversion over to the shared dpll framework, which itself has massive
amounts of checks to make sure that we never leave a display pll
enabled when we shouldn't.
So after that conversion we should stil have a good enough coverage of
asserts for entering pc8/runtime pm on hsw/bdw.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add !mutex_is_locked() checks to intel_pin_and_fence_fb_obj() and
intel_unpin_fb_obj() to help catch failures to grab struct_mutex when
operating on fb objects.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_primary_plane_{setplane,disable} were lacking struct_mutex locking
around their GEM operations.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reported-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.
With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That function can be used to write anything on D_COMP, not just
disable it, so print a more appropriate message.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.
Potential uses of this macro were identified via the following
Coccinelle patch:
@@
expression E;
@@
* to_intel_framebuffer(E)->obj
@@
expression E;
identifier I;
@@
I = to_intel_framebuffer(E);
...
* I->obj
v2: Rewrite some NULL tests in terms of the obj rather than the fb.
Also add a WARN() if trying to pageflip with a disabled primary
plane. [Suggested by Chris Wilson]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Toshiba CB35 Chromebook (with Celeron 2955U CPU) has a controllable
backlight although its VBT reports otherwise. Apply quirk to ignore the
backlight presence check during backlight setup.
Patch tested by author on Toshiba CB35.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Acer C720 and C720P Chromebooks (with Celeron 2955U CPU) have a
controllable backlight although their VBT reports otherwise. Apply quirk
to ignore the backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Accurate frontbuffer tracking and frontbuffer rendering invalidate, flush and
flip events. This is prep work for proper PSR support and should also be
useful for DRRS&fbc.
- Runtime suspend hardware on system suspend to support the new SOix sleep
states, from Jesse.
- PSR updates for broadwell (Rodrigo)
- Universal plane support for cursors (Matt Roper), including core drm patches.
- Prefault gtt mappings (Chris)
- baytrail write-enable pte bit support (Akash Goel)
- mmio based flips (Sourab Gupta) instead of blitter ring flips
- interrupt handling race fixes (Oscar Mateo)
And old, not yet merged features from the previous round:
- rps/turbo support for chv (Deepak)
- some other straggling chv patches (Ville)
- proper universal plane conversion for the primary plane (Matt Roper)
- ppgtt on vlv from Jesse
- pile of cleanups, little fixes for insane corner cases and improved debug
support all over
* tag 'drm-intel-next-2014-06-20' of git://anongit.freedesktop.org/drm-intel: (99 commits)
drm/i915: Update DRIVER_DATE to 20140620
drivers/i915: Fix unnoticed failure of init_ring_common()
drm/i915: Track frontbuffer invalidation/flushing
drm/i915: Use new frontbuffer bits to increase pll clock
drm/i915: don't take runtime PM reference around freeze/thaw
drm/i915: use runtime irq suspend/resume in freeze/thaw
drm/i915: Properly track domain of the fbcon fb
drm/i915: Print obj->frontbuffer_bits in debugfs output
drm/i915: Introduce accurate frontbuffer tracking
drm/i915: Drop schedule_back from psr_exit
drm/i915: Ditch intel_edp_psr_update
drm/i915: Drop unecessary complexity from psr_inactivate
drm/i915: Remove ctx->last_ring
drm/i915/chv: Ack interrupts before handling them (CHV)
drm/i915/bdw: Ack interrupts before handling them (GEN8)
drm/i915/vlv: Ack interrupts before handling them (VLV)
drm/i915: Ack interrupts before handling them (GEN5 - GEN7)
drm/i915: Don't BUG_ON in i915_gem_obj_offset
drm/i915: Grab dev->struct_mutex in i915_gem_pageflip_info
drm/i915: Add some L3 registers to the parser whitelist
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
For whatever reason, MI_DISPLAY_FLIP fails to change tiling mode on
Baytrail, so just use CPU driven mmio flips instead.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76176
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently see random GPU hangs when using RCS flips with multiple
pipes on Ivybridge. Now that we have mmio flips, we can fairly cheaply
fallback to using CPU driven flips instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77104
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
The always-on power well pixel path on haswell is routed such that it
bypasses the panel fitter when we use is. Which means the pfit CRC
source won't work in that configuration.
Add a new disallow-bypass flags to the pfit pipe config state and set
it when we want to use the pf CRC. Results in a bit of flicker, but
should get the job done. We'll also undo do it afterwards to make sure
other tests arent' negatively affected.
Totally untested due to lack of hsw laptops around here.
v2: s/disallow_bypass/force_power_well_on/ to avoid a double negative
(Damien).
v3: force_thru because roadsigns.
v4: Don't forget the power wells! Also note that until the runtime pm
for DPMS series is fully merged the simple disable/enable trick won't
work since the ->crtc_mode_set callback is still required to do nasty
things. This stuff is tricky, but I think by both fixing up
get_crtc_power_domains and the debugfs wa code we should always
grab/drop the additional power well correctly.
v5: Wrap in () as suggested by Damien to avoid setting reserved values
for the edp transcoder path on bdw+
References: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the root cause is understood now and with the fix
commit 564ed191f5
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Jun 13 14:54:21 2014 +0300
drm/i915: gmch: fix stuck primary plane due to memory self-refresh mode
in place the magic for G4x chipsets introduced with commit
commit 61bc95c1fb
Author: Egbert Eich <eich@suse.com>
Date: Mon Mar 4 09:24:38 2013 -0500
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
to avoided occasional screen blanking on mode changes can finally
be removed.
It's been verified that Imre's fix also resolves the said issue.
Signed-off-by: Egbert Eich <eich@suse.de>
Tested-by: Stefan Dirsch <sndirsch@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Blanking/unblanking the console in a loop on an Asus T100 sometimes
leaves the console blank. After some digging I found that applying
commit 61bc95c1fb
Author: Egbert Eich <eich@suse.com>
Date: Mon Mar 4 09:24:38 2013 -0500
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
fixed VLV too.
In my case the problem seemed to happen already during the previous crtc
disabling and went away if I disabled self-refresh mode before disabling
the primary plane.
The root cause for this is that updates from the shadow to live plane
control register are blocked at vblank time if the memory self-refresh
mode (aka max-fifo mode on VLV) is active at that moment. The controller
checks at frame start time if the CPU is in C0 and the self-refresh mode
enable bit is set and if so activates self-reresh mode, otherwise
deactivates it. So to make sure that the plane truly gets disabled before
pipe-off we have to:
1. disable memory self-refresh mode
2. disable plane
3. wait for vblank
4. disable pipe
5. wait for pipe-off
v2:
- add explanation for the root cause from HW team (Cesar Mancini et al)
- remove note about the CPU C7S state, in my latest tests disabling it
alone didn't make a difference
- add vblank between disabling plane and pipe (Ville)
- apply the same workaround for all gmch platforms (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the CMNRESET deassert is part of the cmnlane power well,
intel_reset_dpio() is called too late to make any difference. We've
deasserted CMNRESET by that time, and so the off+on toggle w/a will
never kick in.
Move the workaround to intel_power_domains_init_hw() where it gets
called before we enable the init power domain.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a slightly different way of readoing out the cdclk in
gmbus_set_freq(). Kill that and just call .get_display_clock_speed().
Also need to remove the GMBUSFREQ update from intel_i2c_reset() since
that gets called way too early. Let's do it in intel_modeset_init_hw()
instead, and also pull the initial vlv_cdclk_freq update there from
init_clock gating.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If someone is interested in the current cdclk frquency it should
be stable and not in process of changing frquency. Warn if the current
and requested cdclk don't match in .get_display_clock_spee() on vlv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV Punit doesn't support the 400MHz cdclk option, so we bypass the
Punit and poke at CCK directly. However we forgot to wait for the
frequeency change to complete. Poll the CCK clock status to make sure
the clock has changed before we fire up any pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the cdclk frequency to 200MHz on vlv when all pipes are off. In
theory we should be able to use 200MHz also when the pixel clock is at
most 90% of 200MHz. However in practice all we seem to get is a solid
color picture or an otherwise corrupted display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the HPLL frequency one of the supported cdclk frquencies is
either 320MHz or 333MHz. Figure out which one it is to accurately pick
the minimal required cdclk. This would also avoid a warning from the
cdclk code where it compares the actual cdclk read out from the hardware
with a value that was calculated using valleyview_calc_cdclk().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a standard hook for reading out the current cdclk. Move the VLV
code from valleyview_cur_cdclk() to .get_display_clock_speed().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid using magic values for CCK frequency bits. Also the mask we were
using for the requested frequency was one bit too short. Fix it up.
Note: This also fixes the #define for a mask (spotted by Jesse in his
review).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add note about mask change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use kHz units in vlv cdclk code since that's more customary.
Also replace the precomputed 90% values with *9/10 computation
for extra clarity.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTuaWZAAoJEHm+PkMAQRiGfkIH/2Hhwrg51GWazUYIXVxz5zLU
kPMlaws3vankbhka9HCg02eS3tkzr6shO3F/qlBba+5GUkUDKCcCisIsvk4hgZZg
7YqepTvcaupNxIp4TmTGm1FYVK1GpaWFdJVgg2PDdGFahw3HSlfZoTkBzirNCwga
p/jfeRzathbUixpz9OAC1AEn2gP1AxNRpSt1wShL5rexBb1YRXCPuCEt9B0UsVoR
mzKf5xEsuaZnpCuvWK4S60fjfVhTe8UJ/xGPPfdLyIXU0rvhaKzfeVQO6F5nIQBy
Xvrar1f7oOPZaJRdlmPvAimS7iS8lq/YctuHu7ia1NdJSihtA5sRPf7cWAw2d7s=
=4PrL
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc4' into drm-intel-next-queued
Due to Dave's vacation drm-next hasn't opened yet for 3.17 so I
couldn't move my drm-intel-next queue forward yet like I usually do.
Just pull in the latest upstream -rc to unblock patch merging - I
don't want to needlessly rebase my current patch pile really and void
all the testing we've done already.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
use mm.h definition
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently we can't trust this field on other platforms and need to find
some other way.
This fixes a regression introduced in
commit 27da3bdfcf
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Apr 4 16:12:07 2014 -0700
drm/i915: use VBT to determine whether to enumerate the VGA port
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BDW signals the flip done interrupt immediately after the DSPSURF write
when the plane is disabled. This is true even if we've already armed
DSPCNTR to enable the plane at the next vblank. This causes major
problems for our page flip code which relies on the flip done interrupts
happening at vblank time.
So what happens is that we enable the plane, and immediately allow
userspace to submit a page flip. If the plane is still in the process
of being enabled when the page flip is issued, the flip done gets
signalled immediately. Our DSPSURFLIVE check catches this to prevent
premature flip completion, but it also means that we don't get a flip
done interrupt when the plane actually gets enabled, and so the page
flip is never completed.
Work around this by re-introducing blocking vblank waits on BDW
whenever we enable the primary plane.
I removed some of the vblank waits here:
commit 6304cd91e7
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Apr 25 13:30:12 2014 +0300
drm/i915: Drop the excessive vblank waits from modeset codepaths
To avoid these blocking vblank waits we should start using the vblank
interrupt instead of the flip done interrupt to complete page flips.
But that's material for another patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79354
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
crtc->primary->fb may be NULL upon entry to intel_pipe_set_base() if the
primary plane has previously been disabled via the universal plane
interface. We need to check for NULL before trying to reference
old_fb's obj.
This fixes a regression introduced in
commit a071fa0064
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 18 23:28:09 2014 +0200
drm/i915: Introduce accurate frontbuffer tracking
Testcase: igt/kms_universal_plane
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For MIPI, DSI PLL is configured separately in vlv_configure_dsi_pll
during the DSI enable sequence
Causing WARN dump otherwise in dpio_reads
v2: Add IS_CHERRYVIEW check as suggested by Ville
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jesse noticed that the punit communication needed to query the VLV power
well status can cause substantial delays. Since we can query the state
frequently, for example during I2C transfers, maintain a cached version
of the HW state to get rid of this delay.
This fixes at least one reported regression where boot time increased by
~4 seconds due to frequent power well state queries on VLV during eDP
EDID read.
This regression has been introduced in
commit bb4932c4f1
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:33 2014 +0300
drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Reported-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.
Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.
But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.
To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).
Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.
v2: Lots of improvements
Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
Suggested by Chris.
Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.
v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.
v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.
v5: Fixup locking around the fbcon set_to_gtt_domain call.
v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
object. We already have precedence for fb_obj in the pin_and_fence
functions.
v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
directly. These functions center on the plane, the actual object is
irrelevant - even a flip to the same object as already active should
cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
currently just calls intel_frontbuffer_flush since the implemenation
differs.
This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.
Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.
v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.
v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.
v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
still has work left to do before it's fully generic.
v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.
v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The downclocking checks a few more things, so not that simple to
convert. Also, this should get unified with the drrs handling and also
use the locking of that. Otoh the drrs locking is about as hapzardous
as no locking, at least on first sight.
For easier conversion ditch the upclocking on unload - we'll turn off
everything anyway.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So from just a quick look we seem to have enough information to
accurately figure out whether a given gem bo is used as a frontbuffer
and where exactly: We have obj->pin_count as a first check with no
false negatives and only negligible false positives. And then we can
just walk the modeset objects and figure out where exactly a buffer is
used as scanout.
Except that we can't due to locking order: If we already hold
dev->struct_mutex we can't acquire any modeset locks, so could
potential chase freed pointers and other evil stuff.
So we need something else. For that introduce a new set of bits
obj->frontbuffer_bits to track where a buffer object is used. That we
can then chase without grabbing any modeset locks.
Of course the consumers of this (DRRS, PSR, FBC, ...) still need to be
able to do their magic both when called from modeset and from gem
code. But that can be easily achieved by adding locks for these
specific subsystems which always nest within either kms or gem
locking.
This patch just adds the relevant update code to all places.
Note that if we ever support multi-planar scanout targets then we need
one frontbuffer tracking bit per attachment point that we expose to
userspace.
v2:
- Fix more oopsen. Oops.
- WARN if we leak obj->frontbuffer_bits when freeing a gem buffer. Fix
the bugs this brought to light.
- s/update_frontbuffer_bits/update_fb_bits/. More consistent with the
fb tracking functions (fb for gem object, frontbuffer for raw bits).
And the function name was way too long.
v3: Size obj->frontbuffer_bits correctly so that all pipes fit in.
v4: Don't update fb bits in set_base on failure. Noticed by Chris.
v5: s/i915_gem_update_fb_bits/i915_gem_track_fb/ Also remove a few
local enum pipe variables which are now no longer needed to make the
function arguments no drop over the 80 char limit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.
The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.
Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.
v2: Improve the commit message a bit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.
The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.
If this breaks anything then we need to augment the enable/disable
functions accordingly.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables the framework for using MMIO based flip calls,
in contrast with the CS based flip calls which are being used currently.
MMIO based flip calls can be enabled on architectures where
Render and Blitter engines reside in different power wells. The
decision to use MMIO flips can be made based on workloads to give
100% residency for Media power well.
v2: The MMIO flips now use the interrupt driven mechanism for issuing the
flips when target seqno is reached. (Incorporating Ville's idea)
v3: Rebasing on latest code. Code restructuring after incorporating
Damien's comments
v4: Addressing Ville's review comments
-general cleanup
-updating only base addr instead of calling update_primary_plane
-extending patch for gen5+ platforms
v5: Addressed Ville's review comments
-Making mmio flip vs cs flip selection based on module parameter
-Adding check for DRIVER_MODESET feature in notify_ring before calling
notify mmio flip.
-Other changes mostly in function arguments
v6: -Having a seperate function to check condition for using mmio flips (Ville)
-propogating error code from i915_gem_check_olr (Ville)
v7: -Adding __must_check with i915_gem_check_olr (Chris)
-Renaming mmio_flip_data to mmio_flip (Chris)
-Rebasing on latest nightly
v8: -Rebasing on latest code
-squash 3rd patch in series(mmio setbase vs page flip race) with this patch
-Added new tiling mode update in intel_do_mmio_flip (Chris)
v9: -check for obj->last_write_seqno being 0 instead of obj->ring being NULL in
intel_postpone_flip, as this is a more restrictive condition (Chris)
v10: -Applied Chris's suggestions for squashing patches 2,3 into this patch.
These patches make the selection of CS vs MMIO flip at the page flip time, and
make the module parameter for using mmio flips as tristate, the states being
'force CS flips', 'force mmio flips', 'driver discretion'.
Changed the logic for driver discretion (Chris)
v11: Minor code cleanup(better readability, fixing whitespace errors, using
lockdep to check mutex locked status in postpone_flip, removal of __must_check
in function definition) (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # snb, ivb
[danvet: Fix up parameter alignement checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spotted while crawling around in the area.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.
However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.
Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.
The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.
v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
obj->framebuffer_references isn't an atomic_t so the decrement needs to
be protected by some lock. struct_mutex seems like the appropriate lock
here, and we may already take it for the obj unref anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DRM core will translate calls to legacy cursor ioctls into universal
cursor calls automatically, so there's no need to maintain the legacy
cursor support. This greatly simplifies the transition since we don't
have to handle reference counting differently depending on which cursor
interface was called.
The aim here is to transition to the universal plane interface with
minimal code change. There's a lot of cleanup that can be done (e.g.,
using state stored in crtc->cursor->fb rather than intel_crtc) that is
left to future patches.
v4:
- Drop drm_gem_object_unreference() that is no longer needed now that
we receive the GEM obj directly rather than looking up the ID.
v3:
- Pass cursor obj to intel_crtc_cursor_set_obj() if cursor fb changes,
even if 'visible' is false. intel_crtc_cursor_set_obj() will notice
that the cursor isn't visible and disable it properly, but we still
need to get intel_crtc->cursor_addr set properly so that we behave
properly if the cursor becomes visible again in the future without
changing the cursor buffer (noted by Chris Wilson and verified
via i-g-t kms_cursor_crc).
- s/drm_plane_init/drm_universal_plane_init/. Due to type
compatibility between enum and bool, everything actually works
correctly with the wrong init call, except for the type of plane that
gets exposed to userspace (it shows up as type 'primary' rather than
type 'cursor').
v2:
- Remove duplicate dimension checks on cursor
- Drop explicit cursor disable from crtc destroy (fb & plane
destruction will take care of that now)
- Use DRM plane helper to check update parameters
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Pallavi G<pallavi.g@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor cursor buffer setting such that the code to actually update the
cursor lives in a new function, intel_crtc_cursor_set_obj(), and takes
a GEM object as a parameter. The existing legacy cursor ioctl handler,
intel_crtc_cursor_set() will now perform the userspace handle lookup and
then call this new function.
This refactoring is in preparation for the universal plane cursor
support where we'll want to update the cursor with an actual GEM buffer
object (obtained via drm_framebuffer) rather than a userspace handle.
v2: Drop obvious kerneldoc and replace with note about function's
reference consumption
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Pallavi G<pallavi.g@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Keeping track of the power domains is a bit messy since crtc->active
is currently updated by the platform hooks, but we need to be aware of
which state transition exactly is going on. Maybe we simply need to
shovel all the power domain handling down into platform code to
simplify this. But doing that requires some more auditing since
currently the ->mode_set callbacks still read some random registers
(to e.g. figure out the reference clocks).
Also note that intel_crtc_update_dpms is always call first/last even
for encoders which have their own dpms functions. Hence we really only
need to update this place here.
Being a quick "does it blow up?" run not really tested yet.
v2: Don't do runtime PM in the DPMS hooks for HAS_DDI platforms since
that is stalled. Also add a comment to explain what's going on.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intel hardware allows the primary plane to be disabled independently of
the CRTC. Provide custom primary plane handling to allow this.
v8:
- Pin/unpin properly when clipping causes the primary plane to be
disabled when it has previously been enabled.
- s/drm_primary_helper_check_update/drm_plane_helper_check_update/
v7:
- Clip primary plane to invisible when crtc is disabled since
intel_crtc->config.pipe_src_{w,h} may be garbage otherwise.
- Unpin old fb before pinning new one in the "just pin and
return" case that is used when the crtc is disabled.
- Don't treat implicit disabling of the primary plane (caused by
clipping) the same way as explicit disabling (caused by fb=0).
For implicit disables, we should leave the fb set and pinned,
whereas for explicit disables we need to unpin the fb before
primary->fb is cleared.
v6:
- Pass rectangles to primary helper check function and get plane
visibility back.
- Wait for pending pageflips on primary plane update/disable.
- Allow primary plane to be updated while the crtc is disabled (changes
will take effect when the crtc is re-enabled if modeset passes -1
for the fb id).
- Drop WARN() if we try to disable the primary plane when it's
already been disabled. This will happen if the crtc gets disabled
after the primary plane has already been disabled independently.
v5:
- Use new drm_primary_helper_check_update() helper function to check
setplane parameter validity.
- Swap primary plane's pipe for pre-gen4 FBC (caught by Ville Syrjälä)
- Cleanup primary plane properly on crtc init failure
v4:
- Don't add a primary_plane field to intel_crtc; that was left over
from a much earlier iteration of this patch series, but is no longer
needed/used now that the DRM core primary plane support has been
merged.
v3:
- Provide gen-specific primary plane format lists (suggested by Daniel
Vetter).
- If the primary plane is already enabled, go ahead and just call the
primary plane helper to do the update (suggested by Daniel Vetter).
- Don't try to disable the primary plane on destruction; the DRM layer
should have already taken care of this for us.
v2:
- Unpin fb properly on primary plane disable
- Provide an Intel-specific set of primary plane formats
- Additional sanity checks on setplane (in line with the checks
currently being done by the DRM core primary plane helper)
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In a future patch, we'll allow the primary plane to be disabled by
userspace via the universal plane API. If a modeset is requested while
the primary plane is disabled, crtc->primary->fb will be NULL which
generally triggers a full modeset (except in fastboot situations). If
we detect that the crtc is active, but there's no primary plane fb,
we should still allow a simple plane update rather than a full modeset
if the mode isn't actually changing (after re-enabling the primary plane
of course).
v2:
- Enable plane after set_base to avoid enabling the plane if set_base
fails, and to make flip+enable atomic (suggested by Ville)
- Drop BUG to WARN if we somehow enter the 'fb_changed' modeset case
with the crtc disabled (suggested by Ville)
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This doesn't look possible but a little extra defense against the
improbable is worth it - an oops here could lockup the machine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we forced the clock buffers on in .pre_pll_enable() we
should probably undo the damage after we've turned the PLL off.
We do the clock buffer force enable in the .pre_pll_enable() hook
as we need to know which port is going to be used, but in the disable
case we don't need the port since we just disable the clock buffers
to both channels. So we can do this in chv_disable_pll() instead
of having to add any kind of .post_pll_disable() hook.
v2: Improve the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because of the upcoming vblank interrupt driven watermark update
mechanism we will have use for vblank interrupts during plane
enabling/disabling. So don't call drm_vblank_off() until planes
are off, and call drm_vblank_on() just before we start to enable
the planes.
v2: Pimp commit message (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
> Bunch of stuff for 3.16 still:
> - Mipi dsi panel support for byt. Finally! From Shobhit&others. I've
> squeezed this in since it's a regression compared to vbios and we've
> been ridiculed about it a bit too often ...
> - connection_mutex deadlock fix in get_connector (only affects i915).
> - Core patches from Matt's primary plane from Matt Roper, I've pushed the
> i915 stuff to 3.17.
> - vlv power well sequencing fixes from Jesse.
> - Fix for cursor size changes from Chris.
> - agpbusy fixes from Ville.
> - A few smaller things.
>
* tag 'drm-intel-fixes-2014-06-06' of git://anongit.freedesktop.org/drm-intel: (32 commits)
drm/i915: BDW: Adding missing cursor offsets.
drm: Fix getconnector connection_mutex locking
drm/i915/bdw: Only use 2g GGTT for 32b platforms
drm/i915: Nuke pipe A quirk on i830M
drm/i915: fix display power sw state reporting
drm/i915: Always apply cursor width changes
drm/i915: tell the user if both KMS and UMS are disabled
drm/plane-helper: Add drm_plane_helper_check_update() (v3)
drm: Check CRTC compatibility in setplane
drm/i915: use VBT to determine whether to enumerate the VGA port
drm/i915: Don't WARN about ring idle bit on gen2
drm/i915: Silence the WARN if the user tries to GTT mmap an incoherent object
drm/i915: Move the C3 LP write bit setup to gen3_init_clock_gating() for KMS
drm/i915: Enable interrupt-based AGPBUSY# enable on 85x
drm/i915: Flip the sense of AGPBUSY_DIS bit
drm/i915: Set AGPBUSY# bit in init_clock_gating
drm/i915/vlv: add pll assertion when disabling DPIO common well
drm/i915/vlv: move DPIO common reset de-assert into __vlv_set_power_well
drm/i915/vlv: re-order power wells so DPIO common comes after TX
drm/i915/vlv: move CRI refclk enable into __vlv_set_power_well
...
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
Apparently it does more harm than good. Thomas Richter reports that
it helps his machine (Thinkpad X31) and there's another report from a
Fujitsu S6010. Also, we've nuked it on i845G already to make Chris'
machine happy.
Cc: Thomas Richter <richter@rus.uni-stuttgart.de>
References: http://mid.mail-archive.com/538C54E0.8090507@rus.uni-stuttgart.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for userspace to create a big object large enough for a
256x256, and then switch over to using it as a 64x64 cursor. This
requires the cursor update routines to check for a change in width on
every update, rather than just when the cursor is originally enabled.
This also fixes an issue with 845g/865g which cannot change the base
address of the cursor whilst it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Antti:rebased, adjusted macro names and moved some lines, no functional
changes]
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Tested-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Cc: stable@vger.kernel.org
Testcase: igt/kms_cursor_crc/cursor-size-change
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some platforms may not have it, and enumerating it is both confusing and
time consuming due to the hotplug and DDC probing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to do this anytime we power gate the DPIO common well.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This needs to be done before we power back on the CMN_BC well so the PHY
can calibrate properly.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a bit like the CMN reset de-assert we do in DPIO_CTL, except
that it resets the whole common lane section of the PHY. This is
required on machines where the BIOS doesn't do this for us on boot or
resume to properly re-calibrate and get the PHY ready to transmit data.
Without this patch, such machines won't resume correctly much of the time,
with the symptom being a 'port ready' timeout and/or a link training
failure.
Note that simply asserting reset at suspend and de-asserting at resume
is not sufficient, nor is simply de-asserting at boot. Both of these
cases have been tested and have still been found to have failures on
some configurations.
v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
A single object may be referenced by multiple registers fundamentally
breaking the static allotment of ids in the current design. When the
object is used the second time, the physical address of the first
assignment is relinquished and a second one granted. However, the
hardware is still reading (and possibly writing) to the old physical
address now returned to the system. Eventually hilarity will ensue, but
in the short term, it just means that cursors are broken when using more
than one pipe.
v2: Fix up leak of pci handle when handling an error during attachment,
and avoid a double kmap/kunmap. (Ville)
Rebase against -fixes.
v3: And fix the error handling added in v2 (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77351
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write to the primary plane base address registrer when we
enable/disable the primary plane in response to sprite coverage. Those
writes will cause the flip counter to increment which could interfere
with the detection of CS flip completion. We could end up completing
CS flips before the CS has even executed the commands from the ring.
To avoid such issues, wait for CS flips to finish before we toggle the
primary plane on/off.
v2: Rebased due to atomic sprite update changes
Testcase: igt/kms_mmio_vs_cs_flip/setplane_vs_cs_flip
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen2 reports FIFO underruns whenever no planes are enabled on the pipe.
So in order to avoid false positives we must enable the FIFO underrun
reporting only when at least one plane is enabled on the pipe. For
now just move the underrun reporting enable/disable points to the
other side of the plane enable/disable point. That doesn't cover cases
when we turn off all the planes for the pipe but leave the pipe running
on purpose, but it's better than the current situation.
On gen4+ we can actually move the underrun reporting enable/disable to
the opposite ends of the crtc enable/disable hooks. I suppose in theory
we could leave the underrun reporting enabled all the time, except on
VLV where PIPESTAT stops working when the display power well is down.
If we ever get around to unifying the PIPESTAT irq handling for all
gmch platforms, we should still follow the VLV route for other platforms.
It would also micro-optimize the irq handler a bit since we could then
skip the PIPESTAT reads for all disabled pipes.
Gen3 is still a mystery, but for now I'm going to assume it behaves
like gen4+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a pipe is already active when we init/resume there might not be a
full modeset afterwards so drm_vblank_on() may not get called. In such
a case if someone is holding a vblank reference across a suspend/resume
cycle drm_vblank_get() called after resuming won't re-enable the vblank
interrupts.
So in order to make sure vblank interrupts get re-enabled post-resume,
call drm_vblank_on() in intel_sanitize_crtc() if the crtc is already
active.
v2: Also drm_vblank_off() if the pipe got disabled magically
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testecase: igt/kms_flip/vblank-vs-suspend
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in the drm vblank rework from Ville and me. drm core parts acked
by Dave Airlie
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Just a bit of fun around the placement of drm_vblank_on. This merge
resolution has been tested in drm-intel-nightly for a while already.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.
This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.
This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!
v2: Keep the display irq disabling, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only the low-level irq handling functions still use integer crtc
indices with this. But fixing that will require a lot more sugery
and some good ideas for backwards compat with old ums userspace.
Both in drivers and in the drm core.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally these functions have been for user modesetting drivers to
ensure vblank processing doesn't fall over completely around modeset
changes. This has been carried over ever since then.
Now that Ville cleaned our vblank handling with an explicit
drm_vblank_off/on braket when disabling/enabling crtcs. So this seems
to be unnecessary now. The most important side effect was that due to
the delayed vblank disabling we have been pretty much guaranteed to
receive a vblank interrupt soonish after a crtc was enabled.
Note that our vblank handling across modeset is still fairly decent
fubar - we don't actually handle vblank counter all to well.
drm_update_vblank_count will make sure that the frame counter always
rolls forward, but userspace isn't really all to ready to cope with
the big jumps this causes.
This isn't a big mostly because the hardware retains the frame
counter. But with runtime pm and also across suspend/resume we fall
over.
Fixing this is a lot more involved and also needs som i-g-ts. So
material for another patch series.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All of the .queue_flip() callbacks duplicate the same code to pin the
buffers and calculate the gtt_offset. Move that code to
intel_crtc_page_flip(). In order to do that we must also move the ring
selection logic there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we've plugged the mmio vs. ring flip race, we shouldn't need
these vblank waits in the modeset codepaths anymore. So get rid of
them.
v2: gen2 needs to wait for planes to turn off before disabling pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the vblank wait is gone from intel_enable_primary_plane(),
hsw_enable_ips() needs to do the vblank wait itself.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_off() will turn off vblank interrupts, but as long as the
refcount is elevated drm_vblank_get() will not re-enable them. This
is a problem is someone is holding a vblank reference while a modeset is
happening, and the driver requires vblank interrupt to work during that
time.
Add drm_vblank_on() as a counterpart to drm_vblank_off() which will
re-enabled vblank interrupts if the refcount is already elevated. This
will allow drivers to choose the specific places in the modeset sequence
at which vblank interrupts get disabled and enabled.
Testcase: igt/kms_flip/*-vs-suspend
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add Testcase tag for the igt I've written.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the enable sequence we first enable the dclkp output to the
display controller, and then enable the PLL. Do the opposite during
the disable sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setup the pipe config dpll state correctly for CHV. Also add
a assert_pipe_disabled() to chv_disable_pll(), and program the
DPLL_MD registers in chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Besides the fairly useless BUG_ON the logic is completely generic
and cane be used on any platform what wants to reuse the shared
dpll support code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the last piece of code which write state to the hardware in
the ironalake ->crtc_mode_set callback.
I think we could merge this with the pll->enable hook, but otoh the
ordering requirements with the ldvs port are really tricky. Doing the
FP0/1 writes up-front before we even prepare the lvds port (in the
pre_pll_enable hook) like on i9xx seems safest.
With this ilk+ platforms are now ready for runtime PM with DPMS. Since
hsw/bdw also support runtime pm besides snb we need to first make the
haswell code save before we can touch the core code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of every time it isn't active: We only need to do that when
the pll is currently unused, i.e. when pll->refcount == 0. For
paranoia add a warning for the ibx case where plls have a fixed
mapping and hence should always be unused after the call to
intel_put_shared_dpll.
v2: Simplify control flow and use struct assignment instead of memcpy
as suggested by Damien.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this all hw writes are also gone from the ->crtc_mode_set hook on
vlv. I wondered whether we should track more of the pll state in the
pipe config, but otoh as long as we don't have shared plls that's not
really useful - the cross-checking of the port clock should be
sufficient.
While at it also de-magic some of the pipe checks, this has been
irking me since a long time.
Whit this vlv is now ready for runtime PM on dpms. If we'd have
runtime PM support in general ...
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two writes are the very last hw writes from the
->crtc_modeset_callback on pre-gen5 hardware. As usual vlv is a bit
different, so this here is just warm-up.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again the same story: This code just transform sw state from the pipe
config into hardware state. And again we can't move the pll code, but
this time around because the state isn't properly tracked in the pipe
config.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again this code just transforms sw state from the pipe config into
hardware state, so we can just move it around. Unfortunately again a
few forward declarations since intel_display.c is becoming a bit of a
mess.
Note that both for i9xx and ironlake code the only things remaining in
the ->crtc_mode_set hook is now the clock state computation and
sharing code. That needs to be moved into the compute config stage so
that we can catch impossible configurations earlier.
Also note that some of the DPLL hw setup code is still run from within
->crtc_mode_set, namele the pll->mode_set callback. We need to move
that first before we can do fancy things like enable runtime PM for
dpms off.
v2: Make it compile again after the rebase, bisectability issue
reported by Wu Fengguang.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now this really should be in the pipe config somewhere, but till now
it isn't. We can at least move it up a bit next to all the other pll
code since intel_dp_set_m_n really doesn't depend upon this.
This is just prep work so that moving all the hw frobbing code from
->crtc_mode_set to ->crtc_enable is clean.
v2: Do the same for haswell while at it, not just for ivb.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All these functions simply convert sw state as encoded in the pipe
config or primary framebuffer into hardware state. So we can move them
all into the crtc enable hook. Unfortunately this means a little bit
of duplication between the i9xx and vlv functions, but since we
already have highly refactored code I think this is acceptable.
Also a pile of forward declarations unfortunately.
Note also that the various <platform>_update_pll functions are still
called from within the ->crtc_mode_set hook. Mostly they compute the
clock state for the pipe config, but unfortunately there are some
random register writes interspersed. Those need to be moved out first
before we can enable runtime PM for DPMS.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can apperently miss them, but breaking the entire driver hampers
testing. So bail out after one minute, our customerary "this is a lost
cause" timeout.
References: https://bugs.freedesktop.org/show_bug.cgi?id=78383
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixed several switch statements, curly braces, dereference operators
and keywords.
Signed-off-by: Robin Schroer <sulamiification@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our two ->crtc_mode_set callbacks really don't care whether the fb is
pinned and set up already or not - all the state computation and
handling which originally looked at the framebuffer is already using
the indirection through the pipe configuration.
Eventually we want to move this up a bit more, but as long as the crtc
mode_set callback still exists (and as long as we don't need to pin an
entire pile of planes due to atomic modesets) there's not much point
in it. So I'll let this be for now.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A lot of the code in set_base is uncessary when the crtc is off, so we
can get rid of it all. Also, we don't need to call the fbc/psr update
functions since the crtc enable/disable hooks do that already.
The only things we really need are:
- Pin the new framebuffer and potentially unpin the old framebuffer
(if the crtc has been on and we only change the configuration).
- Update the plane registers.
The first step will move out of platform code with the very next
patch.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My plan here is to split up set_base into a prepare step, which does
the pinning, and a commit stage, which updates the hw state. Eventually
we should be able to move the prepare step at the beginning of any
atomic update. For now I only want to move the commit step into the
crtc_enable callbacks.
As a prep step sprinkle intel_edp_psr_update all over the place so
that we don't have to concern ourselves with that in the commit step.
v2: Rebase on top of Ville's enable/disable functions for all planes.
v3: Rebase more.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just for consistency, this patch won't fix anything really.
v2: Rebase over all the recent plane enabling shuffling.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Way back we've used this to reject framebuffers with unsupported
pixel formats. But since the modesetting reorg with the compute
config stage we reject those much earlier and just BUG() in this
callback. So switch to a void return type.
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on those platforms which have a simple bit and don't rely
on the fully programmable CSC unit to do this.
Note that with the current code this includes CHV, but I guess that
platform will match BYT.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patch done using the following semantic patch (thanks Daniel for the
help!)
@@
iterator name list_for_each_entry;
iterator name for_each_crtc;
struct drm_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
+for_each_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Generated using the semantic patch:
@@
iterator name list_for_each_entry;
iterator name for_each_intel_crtc;
struct intel_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list,...) {
+for_each_intel_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe might not start to actually run until the port has been enabled
(depends on the platform and port type). So don't try to wait for vblank
after we enabled the pipe but haven't yet enabled the port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already moved the plane disable/enable to happen as the first/last
thing on every other platforms. Follow suit with gmch platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict, as usual.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No CRT output on CHV, so don't call intel_crt_init().
v2: Don't disable CRT on HAS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add chv_crtc_clock_get() to read out the DPLL settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Fix compile due to bikeshedded headers in an earlier patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the chv clock limit, find the best divisor.
The divisor data has been verified with this spreadsheet.
P1273_DPLL_Programming Spreadsheet.
v2: Rebase the code and change the chv_find_best_dpll based on new
standard way to use intel_PLL_is_valid. Besides, clean up some extra
variables.
v3: Ville suggest better fixed point for m2 calculation.
v4: -Add comment for the limit is compute using fast clock. (Ville)
-Don't pass the request clock to chv_clock, as the same function will
be use clock readout, which doens't have request clock. (Ville)
-Add and use DIV_ROUND_CLOSEST_ULL to consistent with other clock
calculation. (Ville)
-Fix the dp m2 after m2 has stored fixed point. (Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Avoid div-by-zero in chv_clock()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the same code for enabling/disabling planes on all platforms. Rename
the functions to reflect that they're no longer specific to any
platform.
For now we leave the plane enable/disable to ccur at the same old
position in the modeset sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We won't be calling intel_enable_primary_plane() or
intel_disable_primary_plane() with the primary plane in the
wrong state. So remove the useless DISPLAY_PLANE_ENABLE checks.
v2: Convert the checks to WARNs instead (Daniel,Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a mechanism by which we can evade the leading edge of vblank. This
guarantees that no two sprite register writes will straddle on either
side of the vblank start, and that means all the writes will be latched
together in one atomic operation.
We do the vblank evade by checking the scanline counter, and if it's too
close to the start of vblank (too close has been hardcoded to 100usec
for now), we will wait for the vblank start to pass. In order to
eliminate random delayes from the rest of the system, we operate with
interrupts disabled, except when waiting for the vblank obviously.
Note that we now go digging through pipe_to_crtc_mapping[] in the
vblank interrupt handler, which is a bit dangerous since we set up
interrupts before the crtcs. However in this case since it's the vblank
interrupt, we don't actually unmask it until some piece of code
requests it.
v2: preempt_check_resched() calls after local_irq_enable() (Jesse)
Hook up the vblank irq stuff on BDW as well
v3: Pass intel_crtc instead of drm_crtc (Daniel)
Warn if crtc.mutex isn't locked (Daniel)
Add an explicit compiler barrier and document the barriers (Daniel)
Note the irq vs. modeset setup madness in the commit message (Daniel)
v4: Use prepare_to_wait() & co. directly and eliminate vbl_received
v5: Refactor intel_pipe_handle_vblank() vs. drm_handle_vblank() (Chris)
Check for min/max scanline <= 0 (Chris)
Don't call intel_pipe_update_end() if start failed totally (Chris)
Check that the vblank counters match on both sides of the critical
section (Chris)
v6: Fix atomic update for interlaced modes
v7: Reorder code for better readability (Chris)
v8: Drop preempt_check_resched(). It's not available to modules
anymore and isn't even needed unless we ourselves cause
a wakeup needing reschedule while interrupts are off
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reasons we want to move away from the ->mode_set
callbacks: All hw state setup needs to move into ->enable hooks (so
that DOMS can do runtime pm) and all the configuration setup needs to
move into the compute_config functions.
To start with this make the enocer->mode_set callback optional.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS can enable a pipe but leave the primary plane disabled. This
coflicts with out current idea of primary_enabled. Read the actual
hardware plane state and set primary_enabled appropriately.
We currently assume that primary_enabled is always true when we're about
to disable a crtc. That needs to change now as the plane may not be
enabled. So replace the relevant WARNs with early returns in
intel_{enable,disable}_primary_hw_plane().
Fixes the following warning
[ 3.831602] WARNING: CPU: 0 PID: 1112 at linux/drivers/gpu/drm/i915/intel_display.c:1918 intel_disable_primary_hw_plane+0xe4/0xf0 [i915]()
which got introduced here by me:
commit e9e39655c0c30cddc3f8c09a757678a24dd36737
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Apr 28 15:53:25 2014 +0300
drm/i915: Remove useless checks from primary enable/disable
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
assert_plane_enabled() is now triggering during FDI link train because
we no longer enable planes that early.
This problem got introduced in:
commit a5c4d7bc18
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Mar 7 18:32:13 2014 +0200
drm/i915: Disable/enable planes as the first/last thing during modeset on ILK+
Just drop the assert since we shouldn't need planes for link training.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Squash in fixup for now unused plane local variable, reported
by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init sizzling on all platforms so move it to the
platform independent runtime resume callback. The ring frequency reinit
is also needed everywhere except on VLV, but gen6_update_ring_freq()
will be a noop on VLV, so we can move this function too to platform
independent code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by the next patch moving the call out from platform
specific RPM callbacks to platform independent code.
No functional change.
v2:
- patch introduce in v2 of the patchset
v3:
- simplify platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While checking the error capture path I noticed that we lacked the
power domain-on check for PIPESTAT so fix this by moving that to where
the rest of pipe registers are captured.
The move also revealed that we actually don't include this register in
the error report, so fix that too.
v2:
- patch introduced in v2 of the patchset
v3:
- add back !HAS_PCH_SPLIT check (Ville)
[ Ignore my previous comment about the gen<=5 || vlv check, I realized
that it's the same as !HAS_PCH_SPLIT. ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Depending on the SDVO output_flags SDVO may have multiple connectors
linking to the same encoder (in intel_connector->encoder->base).
Only one of those connectors should be active (ie link to the encoder
thru drm_connector->encoder).
If intel_connector_break_all_links() is called from intel_sanitize_crtc()
we may break the crtc connection of an encoder thru an inactive connector
in which case intel_connector_break_all_links() will not be called again
for the active connector if this happens to come later in the list due to:
if (connector->encoder->base.crtc != &crtc->base)
continue;
in intel_sanitize_crtc().
This will however leave the drm_connector->encoder linkage for this
active connector in place. Subsequently this will cause multiple
warnings in intel_connector_check_state() to trigger and the driver
will eventually die in drm_encoder_crtc_ok() (because of crtc == NULL).
To avoid this remove intel_connector_break_all_links() and move its
code to its two calling functions: intel_sanitize_crtc() and
intel_sanitize_encoder().
This allows to implement the link breaking more flexibly matching
the surrounding code: ie. in intel_sanitize_crtc() we can break the
crtc link separatly after the links to the encoders have been
broken which avoids above problem.
This regression has been introduced in:
commit 2492935248
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jul 2 20:28:59 2012 +0200
drm/i915: read out the modeset hw state at load and resume time
so goes back to the very beginning of the modeset rework.
v2: This patch takes care of the concernes voiced by Chris Wilson
and Daniel Vetter that only breaking links if the drm_connector
is linked to an encoder may miss some links.
v3: move all encoder handling to encoder loop as suggested by
Daniel Vetter.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
... our current modeset code isn't good enough yet to handle this. The
scenario is:
1. BIOS sets up a cloned config with lvds+external screen on the same
pipe, e.g. pipe B.
2. We read out that state for pipe B and assign the gmch_pfit state to
it.
3. The initial modeset switches the lvds to pipe A but due to lack of
atomic modeset we don't recompute the config of pipe B.
-> both pipes now claim (in the sw pipe config structure) to use the
gmch_pfit, which just won't work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081
Tested-by: max <manikulin@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
haswell_write_eld() is also used on broadwell, so let's not explicitely
mention Haswell. The rest of the function has plenty of debug output
which will print the function name, so we know where we are anyway.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment from Ben: It's a bit unclear whether we need this dance still
on bdw.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
There's no point in hiding the DP M/N setup in the update_pll functions.
Just move it to the mode_set function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Inherit/reuse firmwar framebuffers (for real this time) from Jesse, less
flicker for fastbooting.
- More flexible cloning for hdmi (Ville).
- Some PPGTT fixes from Ben.
- Ring init fixes from Naresh Kumar.
- set_cache_level regression fixes for the vma conversion from Ville&Chris.
- Conversion to the new dp aux helpers (Jani).
- Unification of runtime pm with pc8 support from Paulo, prep work for runtime
pm on other platforms than HSW.
- Larger cursor sizes (Sagar Kamble).
- Piles of improvements and fixes all over, as usual.
* tag 'drm-intel-next-2014-03-21' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915: Include a note about the dangers of I915_READ64/I915_WRITE64
drm/i915/sdvo: fix questionable return value check
drm/i915: Fix unsafe loop iteration over vma whilst unbinding them
drm/i915: Enabling 128x128 and 256x256 ARGB Cursor Support
drm/i915: Print how many objects are shared in per-process stats
drm/i915: Per-process stats work better when evaluated per-process
drm/i915: remove rps local variables
drm/i915: Remove extraneous MMIO for RPS
drm/i915: Rename and comment all the RPS *stuff*
drm/i915: Store the HW min frequency as min_freq
drm/i915: Fix coding style for RPS
drm/i915: Reorganize the overclock code
drm/i915: init pm.suspended earlier
drm/i915: update the PC8 and runtime PM documentation
drm/i915: rename __hsw_do_{en, dis}able_pc8
drm/i915: kill struct i915_package_c8
drm/i915: move pc8.irqs_disabled to pm.irqs_disabled
drm/i915: remove dev_priv->pc8.enabled
drm/i915: don't get/put PC8 when getting/putting power wells
drm/i915: make intel_aux_display_runtime_get get runtime PM, not PC8
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Because if we keep the current code, we'll get tons of WARNs on
Broadwell, since the code is Haswell-specific.
We could have also added a Broadwell-specific code there, but it's not
really needed since we never disable LCPLL with the hotplug interrupts
still enabled. So keep the easy-and-simple-to-maintain solution until
we actually need something else.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Ensure that existing driver loops over all planes do not change behavior
when we begin adding new types of planes (primary and cursor) to the DRM
plane list in future patches.
v2: Switch to using drm_for_each_legacy_plane()
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
That's what the spec said! And HSW needs it through pcode (you can
only read it through MCHBAR), so create hsw_write_dcomp to abstract
the weirdness.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 is part of runtime PM, the check is useless.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just because I have a SNB machine and I can easily test it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we don't keep the hotplug interrupts enabled anymore, we can
kill the regsave struct and just cal the normal IRQ preinstall,
postinstall and uninstall functions. This makes it easier to add
runtime PM support to non-HSW platforms.
The only downside is in case we get a request to update interrupts
while they are disabled, won't be able to update the regsave struct.
But this should never happen anyway, so we're not losing too much.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These were apparently meant to protect the SAREA which only has
room for two pipes, but things clearly went a bit wonky when
first the .update_plane() hooks were split up and then pipe C
got introduced.
The checks actually protecting the SAREA live in
intel_crtc_update_sarea() these days, so the checks in the primary
plane update hooks are just historical leftovers which are to be
eliminated.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those values are, global, only used in one function and already stored
in mode_config.cursor_{width,height}.
As a result, this initialization code has been moved from the
crtc_init() function to the global modeset_init() one.
I also renamed CURSOR_{WIDTH,HEIGHT} to MAX_CURSOR_{WIDTH,HEIGHT} to be
more accurate about what these value really are.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of reading out the CD clock rate from the HW at each modeset, do
this only during driver init and resume and use the cached value during
modeset. This moves things towards a state where the sw and hw side
setup is separated. It's also needed for VLV RPM, where we don't put
device into D0 state until modeset_global_resources is called and thus
can't access any display/gfx registers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If vsyncshift comes out as negative, add one htotal to it to get the
corresponding positive value.
This is rather theoretical as it would require a mode where the
hsync+back porch is very long and the active+front porch very short.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPECONF_INTERLACE_W_FIELD_INDICATION is only meant to be used for sdvo
since it implies a slightly weird vsync shift of htotal/2. For everything
else we should use PIPECONF_INTERLACE_W_SYNC_SHIFT and let the value in
the VSYNCSHIFT register take effect.
The only exception is gen3 simply because VSYNCSHIFT didn't exist yet.
Gen2 doesn't support interlaced modes at all, so we can drop the
explicit gen2 checks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When interlaced sdvo output is used, vsyncshift should supposedly
be (htotal-1)/2. In reality PIPECONF/TRANSCONF will override it by
using the legacy vsyncshift interlace mode which causes the hardware
to ignore the VSYNCSHIFT register.
The only odd thing here is that on PCH platforms we program the
VSYNCSHIFT on both CPU and PCH, and it's not entirely clear if both
sides have to agree on the value or not. On the CPU side there's no
way to override the value via PIPECONF anymore, so if we want to make
the CPU side agree with the PCH side, we should probably program the
approriate value into VSYNCSHIFT manually. So let's do that, but for
now leave the PCH side to still use the legacy interlace mode in
TRANSCONF.
We can also drop the gen2 check since gen2 doesn't support interlaced
modes at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes HDMI testers happier on VLV platforms. It may be that we
need it for any non-SVO platform, but I don't have any tests to back
that up, so I'm leaving other pre-ILK platforms alone for now.
Tested-by: "Clint Taylor <clinton.a.taylor@intel.com>"
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74964
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the cursor width is changed, we may need to recompute our WM to
prevent untold flickering. We hope that the registers are flushed on the
same vblank to prevent underruns...
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit 5c673b60a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Mar 7 20:34:46 2014 +0100
drm/i915: Don't enable display error interrupts from the start
we don't enable underrun interrupts any more at takeover time.
Unfortunately I've forgotten to also adjust the sw-side tracking.
Since the code assumes that disabled pipes have underrun reporting
enabled set the disable flag only on all pipes which are active at
takeover time. Without this underrun reporting wasn't enabled
correctly on the first modeset. Note that for fastboot this is another
piece of state that needs to be fixed up by enabling the underrung
reporting after watermarks have beend fixed up.
On ivb/hsw an additional effect of this regression was that also all
cpu crc reporting stopped working since the master error interrupt it
shared across all pipes and sources.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76150
[danvet: Augment the code comment and polish the commit message a bit,
as discussed with Jani.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch we allow larger cursor planes of sizes 128x128
and 256x256.
v2: Added more precise check on size while setting cursor plane.
v3: Changes related to restructuring cursor size restrictions
and DRM_DEBUG usage.
v4: Indentation related changes for setting cursor control and
implementing DRM_CAP_CURSOR_WIDTH and DRM_CAP_CURSOR_HEIGHT
Testcase: igt/kms_cursor_crc
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: G, Pallavi <pallavi.g@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 got much simpler, there are less things to document.
Also, runtime PM already has a nice documentation, so we don't need to
re-explain it on our driver.
v2: - Rebase.
- Fix typo (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we removed all the intermediate abstractions, we can rename
these functions to just hsw_{en,dis}able_pc8.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When other platforms add runtime PM support they will also need to
disable interrupts, so move the variable to the runtime PM struct.
Also notice that the longer-term goal is to completely kill the
regsave struct, and I even have patches for that.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was just being used on debugfs and on a WARN inside
hsw_set_power_well. But now that we PC8 is part of runtime PM and we
get/put runtime PM when we get/put any power domain, we shouldn't need
the WARN anymore.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we already get/put runtime PM every time we get/put any power
domain, and now PC8 and runtime PM are the same thing.
With this, we can also now kill the hsw_{en,dis}able_package_c8
functions.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the latest changes, the indirection is useless.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since after the latest patches it's only being used to prevent
getting/putting the runtime PM refcount.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of PC8 references. Now that both are the same thing and we
are killing PC8, just get the runtime PM reference.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The requirements_met variable was used to track two things: enabled
CRTCs and the power well. After the latest chagnes, we get a runtime
PM reference whenever we get any of the power domains, and we get
power domains when we enable CRTCs or the power well, so we should
already be covered, not needing this specific tracking.
v2: - Rebase.
v3: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.
While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
- We are not aware of anybody wanting a "PC8 without D3" environment.
- If we keep both features as separate, we'll have to to test both
PC8 and PC8+D3 code paths. We're already having a major pain to
make QA do automated testing of just one thing, testing both paths
will cost even more.
- Only Haswell+ supports PC8, so if we want to add runtime PM support
to, for example, IVB, we'll have to copy some code from the PC8
feature to runtime PM, so merging both features as a single thing
will make it easier for enabling runtime PM on other platforms.
This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.
v2: - Rebase.
v3: - Rebase.
- Fully remove the deprecated i915 params since Daniel doesn't
consider them as part of the ABI.
v4: - Rebase.
- Fix typo in the commit message.
v5: - Rebase, again.
- Add a huge comment explaining the different forcewake usage
(Chris, Daniel).
- Use open-coded forcewake functions (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we merge PC8 and runtime PM, these new functions are going to be
called by the runtime suspend/resume functions, and their callers are
going to be removed.
v2: - Rebase
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The name 'update_plane' was used both for the primary plane functions in
intel_display.c and the sprite/overlay functions in intel_sprite.c.
Rename the primary plane functions to 'update_primary_plane' to avoid
confusion.
On a similar note, intel_display.c already had a function called
intel_disable_primary_plane() that programs the hardware to disable a
pipe's primary plane. When we hook up primary planes through the DRM
plane interface, one of the natural handler names will be
intel_primary_plane_disable(), which is very similar. To avoid
confusion, rename the existing intel_disable_primary_plane() to
intel_disable_primary_hw_plane() to make the two names a little more
distinct.
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
[danvet: Fix up conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
