This provides a missing link in the code chain, as several features implicitly
depend and/or rely on the choice of CCID. Most notably, this is the Send Ack Vector
feature, but also Ack Ratio and Send Loss Event Rate (also taken care of).
For Send Ack Vector, the situation is as follows:
* since CCID2 mandates the use of Ack Vectors, there is no point in allowing
endpoints which use CCID2 to disable Ack Vector features such a connection;
* a peer with a TX CCID of CCID2 will always expect Ack Vectors, and a peer
with a RX CCID of CCID2 must always send Ack Vectors (RFC 4341, sec. 4);
* for all other CCIDs, the use of (Send) Ack Vector is optional and thus
negotiable. However, this implies that the code negotiating the use of Ack
Vectors also supports it (i.e. is able to supply and to either parse or
ignore received Ack Vectors). Since this is not the case (CCID-3 has no Ack
Vector support), the use of Ack Vectors is here disabled, with a comment
in the source code.
An analogous consideration arises for the Send Loss Event Rate feature,
since the CCID-3 implementation does not support the loss interval options
of RFC 4342. To make such use explicit, corresponding feature-negotiation
options are inserted which signal the use of the loss event rate option,
as it is used by the CCID3 code.
Lastly, the values of the Ack Ratio feature are matched to the choice of CCID.
The patch implements this as a function which is called after the user has
made all other registrations for changing default values of features.
The table is variable-length, the reserved (and hence for feature-negotiation
invalid, confirmed by considering section 19.4 of RFC 4340) feature number `0'
is used to mark the end of the table.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.
It also resolves a FIXME regarding the congestion control
initialisation.
Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds list initial fields and list management functions for the
new feature negotiation implementation.
Thanks to Arnaldo for suggestions and improvements.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the sender to distinguish original and retransmitted packets,
which is in particular needed for the retransmission of DCCP-Requests:
* the first Request uses ISS (generated in net/dccp/ip*.c), and sets GSS = ISS;
* all retransmitted Requests use GSS' = GSS + 1, so that the n-th retransmitted
Request has sequence number ISS + n (mod 48).
To add generic support, the patch reorganises existing code so that:
* icsk_retransmits == 0 for the original packet and
* icsk_retransmits = n > 0 for the n-th retransmitted packet
at the time dccp_transmit_skb() is called, via dccp_retransmit_skb().
Thanks to Wei Yongjun for pointing this problem out.
Further changes:
----------------
* removed the `skb' argument from dccp_retransmit_skb(), since sk_send_head
is used for all retransmissions (the exception is client-Acks in PARTOPEN
state, but these do not use sk_send_head);
* since sk_send_head always contains the original skb (via dccp_entail()),
skb_cloned() never evaluated to true and thus pskb_copy() was never used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TFRC loss detection code used the wrong loss condition (RFC 4340, 7.7.1):
* the difference between sequence numbers s1 and s2 instead of
* the number of packets missing between s1 and s2 (one less than the distance).
Since this condition appears in many places of the code, it has been put into a
separate function, dccp_loss_free().
Further changes:
----------------
* tidied up incorrect typing (it was using `int' for u64/s64 types);
* optimised conditional statements for common case of non-reordered packets;
* rewrote comments/documentation to match the changes.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Change struct proto destroy function pointer to return void. Noticed
by Al Viro.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit() and the other IP output functions expect to get a skb
with clear or properly initialized skb->cb. Unlike TCP and UDP, the
dccp_skb_cb doesn't contain a struct inet_skb_parm at the beginning,
so the DCCP-specific data is interpreted by the IP output functions.
This can cause false negatives for the conditional POST_ROUTING hook
invocation, making the packet bypass the hook.
Add a inet_skb_parm/inet6_skb_parm union to the beginning of
dccp_skb_cb to avoid clashes. Also add a BUILD_BUG_ON to make
sure it fits in the cb.
[ Combined with patch from Gerrit Renker to remove two now unnecessary
memsets of IPCB(skb)->opt ]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dccp_v(4|6)_ctl_socket with sock to unify a code with TCP/ICMP.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way we can remove TCP and DCCP specific versions of
sk->sk_prot->get_port: both v4 and v6 use inet_csk_get_port
sk->sk_prot->hash: inet_hash is directly used, only v6 need
a specific version to deal with mapped sockets
sk->sk_prot->unhash: both v4 and v6 use inet_hash directly
struct inet_connection_sock_af_ops also gets a new member, bind_conflict, so
that inet_csk_get_port can find the per family routine.
Now only the lookup routines receive as a parameter a struct inet_hashtable.
With this we further reuse code, reducing the difference among INET transport
protocols.
Eventually work has to be done on UDP and SCTP to make them share this
infrastructure and get as a bonus inet_diag interfaces so that iproute can be
used with these protocols.
net-2.6/net/ipv4/inet_hashtables.c:
struct proto | +8
struct inet_connection_sock_af_ops | +8
2 structs changed
__inet_hash_nolisten | +18
__inet_hash | -210
inet_put_port | +8
inet_bind_bucket_create | +1
__inet_hash_connect | -8
5 functions changed, 27 bytes added, 218 bytes removed, diff: -191
net-2.6/net/core/sock.c:
proto_seq_show | +3
1 function changed, 3 bytes added, diff: +3
net-2.6/net/ipv4/inet_connection_sock.c:
inet_csk_get_port | +15
1 function changed, 15 bytes added, diff: +15
net-2.6/net/ipv4/tcp.c:
tcp_set_state | -7
1 function changed, 7 bytes removed, diff: -7
net-2.6/net/ipv4/tcp_ipv4.c:
tcp_v4_get_port | -31
tcp_v4_hash | -48
tcp_v4_destroy_sock | -7
tcp_v4_syn_recv_sock | -2
tcp_unhash | -179
5 functions changed, 267 bytes removed, diff: -267
net-2.6/net/ipv6/inet6_hashtables.c:
__inet6_hash | +8
1 function changed, 8 bytes added, diff: +8
net-2.6/net/ipv4/inet_hashtables.c:
inet_unhash | +190
inet_hash | +242
2 functions changed, 432 bytes added, diff: +432
vmlinux:
16 functions changed, 485 bytes added, 492 bytes removed, diff: -7
/home/acme/git/net-2.6/net/ipv6/tcp_ipv6.c:
tcp_v6_get_port | -31
tcp_v6_hash | -7
tcp_v6_syn_recv_sock | -9
3 functions changed, 47 bytes removed, diff: -47
/home/acme/git/net-2.6/net/dccp/proto.c:
dccp_destroy_sock | -7
dccp_unhash | -179
dccp_hash | -49
dccp_set_state | -7
dccp_done | +1
5 functions changed, 1 bytes added, 242 bytes removed, diff: -241
/home/acme/git/net-2.6/net/dccp/ipv4.c:
dccp_v4_get_port | -31
dccp_v4_request_recv_sock | -2
2 functions changed, 33 bytes removed, diff: -33
/home/acme/git/net-2.6/net/dccp/ipv6.c:
dccp_v6_get_port | -31
dccp_v6_hash | -7
dccp_v6_request_recv_sock | +5
3 functions changed, 5 bytes added, 38 bytes removed, diff: -33
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function follows48(), which is a special-case of dccp_delta_seqno(),
is nowhere used in the DCCP code, thus removed by this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a separate routine to insert options during the initial handshake.
The main purpose is to conduct feature negotiation, for the moment the only user
is the timestamp echo needed for the (CCID3) handshake RTT sample.
Padding of options has been put into a small separate routine, to be shared among
the two functions. This could also be used as a generic routine to finish inserting
options.
Also removed an `XXX' comment since its content was obvious.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes another Fixme, using the TCP maximum RTO rather than the value
specified by the DCCP specification. Across the sections in RFC 4340, 64
seconds is consistently suggested as maximum RTO backoff value; and this is
the value which is now used.
I have checked both termination cases for retransmissions of Close/CloseReq:
with the default value 15 of `retries2', and an initial icsk_retransmit = 0,
it takes about 614 seconds to declare a non-responding peer as dead, after
which the final terminating Reset is sent. With the TCP maximum RTO value of
120 seconds it takes (as might be expected) almost twice as long, about 23
minutes.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hooks up the TFRC Loss Interval database with CCID 3 packet reception.
In addition, it makes the CCID-specific computation of the first loss
interval (which requires access to all the guts of CCID3) local to ccid3.c.
The patch also fixes an omission in the DCCP code, that of a default /
fallback RTT value (defined in section 3.4 of RFC 4340 as 0.2 sec); while
at it, the upper bound of 4 seconds for an RTT sample has been reduced to
match the initial TCP RTO value of 3 seconds from[RFC 1122, 4.2.3.1].
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as per RFC 4340, sec. 7.7.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This factors code common to dccp_v{4,6}_ctl_send_reset into a separate function,
and adds support for filling in the Data 1 ... Data 3 fields from RFC 4340, 5.6.
It is useful to have this separate, since the following Reset codes will always
be generated from the control socket rather than via dccp_send_reset:
* Code 3, "No Connection", cf. 8.3.1;
* Code 4, "Packet Error" (identification for Data 1 added);
* Code 5, "Option Error" (identification for Data 1..3 added, will be used later);
* Code 6, "Mandatory Error" (same as Option Error);
* Code 7, "Connection Refused" (what on Earth is the difference to "No Connection"?);
* Code 8, "Bad Service Code";
* Code 9, "Too Busy";
* Code 10, "Bad Init Cookie" (not used).
Code 0 is not recommended by the RFC, the following codes would be used in
dccp_send_reset() instead, since they all relate to an established DCCP connection:
* Code 1, "Closed";
* Code 2, "Aborted";
* Code 11, "Aggression Penalty" (12.3).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This implements a SHOULD from RFC 4340, 7.5.4:
"To protect against denial-of-service attacks, DCCP implementations SHOULD
impose a rate limit on DCCP-Syncs sent in response to sequence-invalid packets,
such as not more than eight DCCP-Syncs per second."
The rate-limit is maintained on a per-socket basis. This is a more stringent
policy than enforcing the rate-limit on a per-source-address basis and
protects against attacks with forged source addresses.
Moreover, the mechanism is deliberately kept simple. In contrast to
xrlim_allow(), bursts of Sync packets in reply to sequence-invalid packets
are not supported. This foils such attacks where the receipt of a Sync
triggers further sequence-invalid packets. (I have tested this mechanism against
xrlim_allow algorithm for Syncs, permitting bursts just increases the problems.)
In order to keep flexibility, the timeout parameter can be set via sysctl; and
the whole mechanism can even be disabled (which is however not recommended).
The algorithm in this patch has been improved with regard to wrapping issues
thanks to a suggestion by Arnaldo.
Commiter note: Rate limited the step 6 DCCP_WARN too, as it says we're
sending a sync.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds fields to support the informational Data 1..3 fields of the
DCCP-Reset packets (RFC 4340, 5.6), and makes minor cosmetic changes
to documentation.
Code which fills in these fields follows in subsequent patches, it is
primarily used for reporting option-processing and feature-negotiation
errors.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds a FIXME to signal that the function dccp_send_delayed_ack is nowhere
used in the entire DCCP/CCID code.
Using a delayed Ack timer is suggested in 11.3 of RFC 4340, but it has also
rather subtle implications for the Ack-Ratio-accounting.
CCID2 does not use this (maybe it should).
I think leaving the function in is good, in case someone wants to implement
this.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
The third parameter of dccp_sample_rtt now becomes useless and is removed.
Also combined the subtraction of the timestamp echo and the elapsed time.
This is safe, since (a) presence of timestamp echo is tested first and (b)
elapsed time is either present and non-zero or it is not set and equals 0
due to the memset in dccp_parse_options.
To avoid measuring option-processing time, the timestamp for measuring the
initial Request/Response RTT sample is taken directly when the function is
called (the Linux implementation always adds a timestamp on the Request,
so there is no loss in doing this).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a timesource, conveniently used for DCCP timestamps, which
returns the elapsed time in 10s of microseconds since initialisation.
This makes for a wrap-around time of about 11.9 hours, which should be
sufficient for most applications.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling with EXTRA_CFLAGS=-W notice that we have signed/unsigned issue
in dccp.h.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
A recurring problem, in particular in the CCID code, is that RTT samples
from packets with timestamp echo and elapsed time options need to be taken.
This service is provided via a new function dccp_sample_rtt in this patch.
Furthermore, to protect against `insane' RTT samples, the sampled value
is bounded between 100 microseconds and 4 seconds - for which u32 is sufficient.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently debugging output (when configured) is automatically enabled when
DCCP modules are compiled into the kernel rather than built as loadable modules.
This is not necessary, since the module parameters in this case become kernel
commandline parameters, e.g. DCCP or CCID3 debug output can be enabled for a
static build by appending the following at the boot prompt:
dccp.dccp_debug=1 dccp_ccid3.ccid3_debug=1
This patch therefore does away with the more complicated way of always enabling
debug output for static builds
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The follows48 relation identifies whether 48-bit sequence number
x is the direct successor of y. Currently, it does not handle cases
of the following type correctly:
follows48(0x(prefix)10000LL, 0x(prefix)0FFFFLL)
where prefix is an arbitrary hex sequence of up to 7 digits.
This is fixed by reusing the new dccp_delta_seqno function.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch
* organizes the sequence arithmetic functions into one corner of dccp.h
* performs a small modification of dccp_set_seqno to make it more widely reusable
(now it is safe to use any number, since it performs modulo-2^48 assignment)
* adds functions and generic macros for 48-bit sequence arithmetic:
--48 bit complement
--modulo-48 addition and modulo-48 subtraction
--dccp_inc_seqno now a special case of add48
Constants renamed following a suggestion by Arnaldo.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX CCID needs the write_xmit_timer for delaying packet sends. Previously
this timer was only activated on active (connecting) sockets.
This patch initialises the write_xmit_timer in sync with the other timers, i.e.
the timer will be ready on any socket. This is used by applications with a
listening socket which start to stream after receiving an initiation by the
client. The write_xmit_timer is stopped when the application closes, as before.
Was tested to work and to remove the timer bug reported on dccp@vger.
Also moved timer initialisation into timer.c (static).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
Most target types in the CCID3 code are u32, so subtle conversion errors
can occur if signed time calculations yield negative results: the original
values are lost in the conversion to unsigned, calculation errors go undetected.
This patch therefore
* sets all critical time types from unsigned to suseconds_t
* avoids comparison between signed/unsigned via type-casting
* provides ample warning messages in case time calculations are negative
These warning messages can be removed at a later stage when the code
has undergone more testing.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
It simplifies waiting for the CCID module to signal that a packet
is ready to be sent. Other simplifications flow on from this such as
removing constants.
As a result of this EAGAIN is not returned any more by dccp_wait_for_ccid
(which would otherwise lead to unnecessarily discarding the packet in
dccp_write_xmit).
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reaps the benefit of the earlier patch, which changed the type of
CCID 3 states to use enums, in that many conditions are now simplified
and the number of possible (unexpected) values is greatly reduced.
In a few instances, this also allowed to simplify pre-conditions; where
care has been taken to retain logical equivalence.
[DCCP]: Introduce a consistent BUG/WARN message scheme
This refines the existing set of DCCP messages so that
* BUG(), BUG_ON(), WARN_ON() have meaningful DCCP-specific counterparts
* DCCP_CRIT (for severe warnings) is not rate-limited
* DCCP_WARN() is introduced as rate-limited wrapper
Using these allows a faster and cleaner transition to their original
counterparts once the code has matured into a full DCCP implementation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Previously the transmit queue was unbounded.
This patch:
* puts a limit on transmit queue length
and sends back EAGAIN if the buffer is full
* sets the TX queue length to a sensible default
* implements tx buffer sysctls for DCCP
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch
* makes debugging (when configured) work both for static / module build
* provides generic debugging macros for use in other DCCP / CCID modules
* adds missing information about debug parameters to Kconfig
* performs some code tidy-up
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch tackles the following problem:
* the ccid3_hc_{t,r}x_sock define ccid3hc{t,r}x_state as `u8', but
in reality there can only be a few, pre-defined enum names
* this necessitates addiditional checking for unexpected values
which would otherwise be caught by the compiler
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In order to make their function clearer and obtain a consistent naming
scheme to identify sysctls, all existing DCCP sysctls have been prefixed
with `sysctl_dccp', following the same convention as used by TCP.
Feature-specific sysctls retain the `feat' in the middle, although the
`default' has been dropped, since it is obvious from use.
Also removed a duplicate `dccp_feat_default_sequence_window' in ipv4.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds 3 sysctls which govern the retransmission behaviour of DCCP control
packets (3way handshake, feature negotiation).
It removes 4 FIXMEs from the code.
The close resemblance of sysctl variables to their TCP analogues is emphasised
not only by their name, but also by giving them the same initial values.
This is useful since there is not much practical experience with DCCP yet.
Furthermore, with regard to the previous patch, it is now possible to limit
the number of keepalive-Responses by setting net.dccp.default.request_retries
(also a bit like in TCP).
Lastly, added documentation of all existing DCCP sysctls.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does the following:
a) introduces variable-length checksums as specified in [RFC 4340, sec. 9.2]
b) provides necessary socket options and documentation as to how to use them
c) basic support and infrastructure for the Minimum Checksum Coverage feature
[RFC 4340, sec. 9.2.1]: acceptability tests, user notification and user
interface
In addition, it
(1) fixes two bugs in the DCCPv4 checksum computation:
* pseudo-header used checksum_len instead of skb->len
* incorrect checksum coverage calculation based on dccph_x
(2) removes dccp_v4_verify_checksum() since it reduplicates code of the
checksum computation; code calling this function is updated accordingly.
(3) now uses skb_checksum(), which is safer than checksum_partial() if the
sk_buff has is a non-linear buffer (has pages attached to it).
(4) fixes an outstanding TODO item:
* If P.CsCov is too large for the packet size, drop packet and return.
The code has been tested with applications, the latest version of tcpdump now
comes with support for partial DCCP checksums.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch fixes data being spewed into the logs continually. As the
code stood if there was a large queue and long delays timeo would go
down to zero and never get reset.
This fixes it by resetting timeo. Put constant into header as well.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch removes two functions, the send_ack functions of request_sock,
which are not called/used by the DCCP code. It is correct that these
functions are not called, below is a justification why calling these
functions (on a passive socket in the LISTEN/RESPOND state) would mean
a DCCP protocol violation.
A) Background: using request_sock in TCP:
Gerrit Renker noticed dccp_tw_deschedule and submitted a patch with a FIXME,
but as he suggests in the same patch the best thing is to just ditch this
declaration, while doing that also noticed that tcp_tw_count is as well not
defined anywhere, so ditch it too.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
