Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
lready have rf_vals_3x with same values. Hence rf_vals_3053 is removed
in this patch.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update rf registers to use the same values that the MediaTek/Ralink
reference driver DPO_RT5572_LinuxSTA_2.6.1.3_20121022 uses.
References:
RF5390RegTable in chips/rt5390.c
RF5392RegTable in chips/rt5390.c
Tested on TP-Link TL-WN727N and D-Link DWA-140 Rev.b3 usb wifi dongles.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing it to get the current operating channel is racy and in the way
of further channel handling related changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not exposed as a configuration option anyway
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding the scanning state machine to ath9k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework its wrapper function to make it more generic, using it as a
replacement for previous calls to ath9k_cmn_update_ichannel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was some duplication between channelFlags and chanmode, as well as
a lot of redundant checks based on the combinations of flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware is always configured with OFDM support enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware 802.11b-only mode isn't supported by the driver (the device is
configured for 802.11n/g instead). Simplify the code by removing checks
for it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use wrappers where available. Simplifies code and helps with further
improvements to the channel data structure
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no shared code for handling both rx and tx buffers, and tx
buffers require a lot more metadata than rx buffers.
Using a separate data structure for rx reduces memory usage and improves
cache footprint.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/wcn36xx/debug.c:27:11-31: WARNING opportunity for simple_open, see also structure on line 106
/c/kernel-tests/src/i386/drivers/net/wireless/ath/wcn36xx/debug.c:27:11-31: WARNING opportunity for simple_open, see also structure on line 148
This removes an open coded simple_open() function
and replaces file operations references to the function
with simple_open() instead.
Generated by: coccinelle/api/simple_open.cocci
CC: Eugene Krasnikov <k.eugene.e@gmail.com>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the appropriate helper functions instead of
directly accessing the rt2x00dev->cap_flags field
to check device capability flags.
This improves readability of the code a bit.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the appropriate helper functions instead of
directly accessing the rt2x00dev->cap_flags field
to check device capability flags.
This improves readability of the code a bit.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the appropriate helper functions instead of
directly accessing the rt2x00dev->cap_flags field
to check device capability flags.
This improves readability of the code a bit.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the appropriate helper functions instead of
directly accessing the rt2x00dev->cap_flags field
to check device capability flags.
This improves readability of the code a bit.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 code directly accesses the 'cap_flags'
field of 'struct rt2x00_dev' when checking presence
of a given capability flag. The direct access needs
long expressions which lowers readability of the code.
Add a few helper functions which can be used to test
device capabilities without directly accessing the
cap_flags filed.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust whitespaces to move badly aligned constants
to the right column.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds missing cfg80211_disconnected event for P2P client
interface upon successful deauthenticate command, deauthenticate
event or disassociate event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device is surprise removed, commands sent to FW including
deauthenticate command fail as bus writes fail.
We update our media_connected status to false and inform cfg80211
about disconnection only when command is successful. Since cfg80211
assumes device is still connected, it results into following
WARN_ON during unload:
WARNING: CPU: 0 PID: 18245 at net/wireless/core.c:937
cfg80211_netdev_notifier_call+0x175/0x4d0 [cfg80211]()
Avoid this by emitting cfg80211_disconnected event even if the
deauthenticate command fails.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes "lost interrupt" problems that occurred on SPI-based systems.
cw1200_irq_handler() expects the hwbus to be locked, but on the
SPI-path, that lock wasn't taken (unlike in the SDIO-path, where the
generic SDIO-code takes care of acquiring the lock).
Cc: stable@vger.kernel.org
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver uses different RSSI threshold
and VGC adjustment values for the RT3572 and
RT3593 chipsets.
Update the rt2800_link_tuner function to use the
same values. Also change the comment in the function
to make it more generic.
References:
RT35xx_ChipAGCAdjust function in chips/rt35xx.c
RSSI_FOR_MID_LOW_SENSIBILITY constant in include/chip/rtmp_phy.h
RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 3d81535ea5
(rt2800: 5592: add chip specific vgc calculations)
the rt2800_link_tuner function has been modified to
adjust VGC level for the RT5592 chipset.
On the RT5592 chipset, the VGC level must be adjusted
only if rssi is greater than -65. However the current
code adjusts the VGC value by 0x10 regardless of the
actual chipset if the rssi value is between -80 and
-65.
Fix the broken behaviour by reordering the if-else
statements.
Cc: stable@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the local MOVING_AVERAGE implementation, and use
the generic EWMA functions instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800_config_channel_rf3xxx(), there's no need to toggle
RF R30 bit 7 twice.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pausing queue on flush make no sense since txdone procedure un-pause
queue. Before flush procedure we have to assure queue is stopped,
i.e. on receive path h/w RX is disabled, on transmit path queue is
disabled in mac80211. That conditions are true except one function:
rt2x00usb_watchdog_tx_dma(), so add stop/start queue there.
Note stop/start queue can be racy if we do this from multiple paths,
but currently we stop TX queues only on rt2x00lib_disable_radio(),
which also stop/sync watchdog, hance we have no race condition.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 driver uses 0x22 as a default VGC value
in VGC adjustment for the RT3572 chipset. In the
Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022 driver,
this value is only used for initialization. During
VGC adjustment, the reference driver uses different
values.
Update the 'rt2800_get_default_vgc' function to
synchronize the values with the reference driver.
Also add the missing AGC initialization code into
the 'rt2800_config_channel' function.
References:
RT35xx_SetAGCInitValue in chip/rt35xx.c
RT35xx_ChipAGCAdjust in chip/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver, programming of the 'BBP 66' register
on the RT3572 and RT3593 chipsets must be done via the
'rt2800_bbp_write_with_rx_chain' function. This ensures
that value is correclty set for all RX chains.
References:
RT35xx_ChipAGCAdjust and RT35xx_SetAGCInitValue functions
in chips/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rt2800_get_default_vgc function to use the same VGC
values that the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference
driver uses.
References:
RT35xx_ChipAGCAdjust in chips/rt35xx.c
RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TXPOWER_DELTA field of the regular EEPROM
stores the TX power compensation value for HT40.
The extended EEPROM has no such field, it stores
separate TX power values for HT20 and for HT40.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comments are indicating that the TXMIXER_GAIN_BG
and TXMIXED_GAIN_A entries are overlapping with the
RSSI_BG2 and RSSI_A2 entries in the extended EEPROM
map. This is not correct, because the upper byte of
the RSSI_BG2 and RSSI_A2 entries are reserved. There
are no TX mixer gain values are stored at all in the
extended EEPROM.
Remove the initialization of these entries from the
extended EEPROM map to reflect this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some BCM4313 out there with a PCI id of 0x4313. These devices
are missing a sprom and are only used on routers or other embedded
devices. We found one connected to a BCM63XX SoC.
This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TI firmwares are located under ti-connectivity
directory. Update path to make sure driver can
find and load firmware blob.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently driver name is wrong. PCI device address is visible at
/proc/interrupts instead of the name:
43: 124 0 0 0 PCI-MSI-edge rtsx_pci
44: 384 0 0 0 PCI-MSI-edge snd_hda_intel
45: 25096 0 0 0 PCI-MSI-edge 0000:01:00.0
^^^^^^^^^^^^
So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME
and good for that, so pass it.
Handler names will be "rt2500pci", "rt2500pci" etc.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: Ivo van Doorn <IvDoorn@gmail.com>
CC: Gertjan van Wingerde <gwingerde@gmail.com>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
CC: linux-wireless@vger.kernel.org
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So
far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS
Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx
A lot people made a contribution to this driver. Here is the list in
alphabetical order:
Eugene Krasnikov <k.eugene.e@gmail.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Olof Johansson <dev@skyshaper.net>
Pontus Fuchs <pontus.fuchs@gmail.com>
Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variables cancel_scan_cmd, enable_data, hs_activate and valid are
only assigned the values true and false. Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The merge b35c8097 seems to have lost commit eabc4ac5d,
put the code back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
0411,0241 RT5572 BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170 RT3572 Logitec LAN-W300AN/U2
0846,9013 RT3573 NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e RT3573 Sitecom WiFi USB adapter N900
2001,3c1f RT3573 D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20 RT5372 D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21 RT5572 D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22 RT5372 D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23 RT5372 D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29 ? Planex GW-USMirco300
20f4,724a RT5572 TRENDnet N600 Wireless Dual Band USB Adapter
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it.
Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it.
Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
