And while at it - use the proper assembler macro which includes the
optional irq tracing already - de-uglify'ing the code a bit
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Up until now we had ARC PGU not enabled in axs10x defconfigs trying
to not bloat kernel image again with yet another drivers and subsystems.
This change configures ARC PGU (as well as DRM bits it depends on)
to be built as a module and so those who need LCD screen to work on
axs10x may bundle built .ko files in their target's file-system with
help of the following command on host:
------------->8-------------
make INSTALL_MOD_PATH=_path_to_target_fs_ modules_install
------------->8-------------
and later on target with commands as simple as:
------------->8-------------
modprobe adv7511.ko
modprobe arcpgu.ko
------------->8-------------
get LCD working.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There are more ARC Linux HAPS users than Zebu ones.
Same kernel would work fine on both, even with embedded DT, assuming the FPGA
bitfile configuration is same
Suggested-by: Francois Bedard <fbedard@ynopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This new header file is for NPS400 SoC (part of ARC architecture).
The header file includes macros for save/restore of HW scheduling.
The control of HW scheduling is achieved by writing core registers.
This code was moved from arc/plat-eznps so it can be used
from drivers/clocksource/, available only for CONFIG_EZNPS_MTM_EXT.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds support for
- CONFIG_ARC_TIMERS : legacy 32-bit TIMER0 and TIMER1 which count UP
from @CNT to @LIMIT, before optionally triggering an interrupt.
These are programmed using ARC auxiliary register interface.
These are present in all ARC cores (ARC700 and ARC HS38)
TIMER0 serves as clockevent for all ARC linux builds.
TIMER1 is used for clocksource in arc700 builds.
- CONFIG_ARC_TIMERS_64BIT: 64-bit counters, RTC and GFRC found in
ARC HS38 cores. These are independnet IP blocks with different
programming model respectively.
Link: http://lkml.kernel.org/r/20161111231132.GA4186@mai
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Also remove the dependency on ARCv2, to increase compile coverage for
!ARCV2 builds
Acked-by: Daniel Lezcano <daniel.lezcnao@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC timers use aux registers for programming and this paves way for
moving ARC timer drivers into drivers/clocksource
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
to allow future git mv of the driver into drivers/clocksource
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original distinction was done as they were developed at different
times and primarily because they are specific to UP (RTC) and SMP (GFRC).
But given that driver handles that at runtime, (i.e. not allowing
RTC as clocksource in SMP), we can simplify things a bit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
... don't rely on cpuinfo populated in arc boot code. This paves way for
moving this code in drivers/clocksource/
And while at it, convert the WARN() to pr_warn() as sugested by Daniel
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
A standard "C" shift will be handled appropriately by the compiler
depending on the endian for the build. So we don't need the
explicit distinction in code
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
commit 1c3c909303 broke PAE40. Macro pfn_pte(pfn, prot) creates paddr
from pfn, but the page shift was getting truncated to 32 bits since we lost
the proper cast to 64 bits (for PAE400
Instead of reverting that commit, use a better helper which is 32/64 bits
safe just like ARM implementation.
Fixes: 1c3c909303 ("ARC: mm: fix build breakage with STRICT_MM_TYPECHECKS")
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: massaged changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Apparenty this is coming in the way of gcc fix which inhibits the usage
of LP_COUNT as a gpr.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
No need to duplicate the same define everywhere. Since
the only user is stop-machine and the only provider is
s390, we can use a default implementation of cpu_relax_yield()
in sched.h.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-s390 <linux-s390@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1479298985-191589-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As there are no users left, we can remove cpu_relax_lowlatency()
implementations from every architecture.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Cc: <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1477386195-32736-6-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For spinning loops people do often use barrier() or cpu_relax().
For most architectures cpu_relax and barrier are the same, but on
some architectures cpu_relax can add some latency.
For example on power,sparc64 and arc, cpu_relax can shift the CPU
towards other hardware threads in an SMT environment.
On s390 cpu_relax does even more, it uses an hypercall to the
hypervisor to give up the timeslice.
In contrast to the SMT yielding this can result in larger latencies.
In some places this latency is unwanted, so another variant
"cpu_relax_lowlatency" was introduced. Before this is used in more
and more places, lets revert the logic and provide a cpu_relax_yield
that can be called in places where yielding is more important than
latency. By default this is the same as cpu_relax on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-2-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- mmap handler for dma ops as generic handler no longer works for us [Alexey]
- Fixes for EZChip platform [Noam]
- Fix RTC clocksource driver build issue
- ARC IRQ handling fixes [Yuriy]
- Revert a recent makefile change which doesn't go well with oldish tools out in the wild
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hbBv
-----END PGP SIGNATURE-----
Merge tag 'arc-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- mmap handler for dma ops as generic handler no longer works for us
[Alexey]
- Fixes for EZChip platform [Noam]
- Fix RTC clocksource driver build issue
- ARC IRQ handling fixes [Yuriy]
- Revert a recent makefile change which doesn't go well with oldish
tools out in the wild
* tag 'arc-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: MCIP: Use IDU_M_DISTRI_DEST mode if there is only 1 destination core
ARC: IRQ: Do not use hwirq as virq and vice versa
ARC: [plat-eznps] set default baud for early console
ARC: [plat-eznps] remove IPI clear from SMP operations
Revert "ARC: build: retire old toggles"
ARC: timer: rtc: implement read loop in "C" vs. inline asm
ARC: change return value of userspace cmpxchg assist syscall
arc: Implement arch-specific dma_map_ops.mmap
ARC: [SMP] avoid overriding present cpumask
ARC: Enable PERF_EVENTS in nSIM driven platforms
Traditionally, we have always had warnings about uninitialized variables
enabled, as this is part of -Wall, and generally a good idea [1], but it
also always produced false positives, mainly because this is a variation
of the halting problem and provably impossible to get right in all cases
[2].
Various people have identified cases that are particularly bad for false
positives, and in commit e74fc973b6 ("Turn off -Wmaybe-uninitialized
when building with -Os"), I turned off the warning for any build that
was done with CC_OPTIMIZE_FOR_SIZE. This drastically reduced the number
of false positive warnings in the default build but unfortunately had
the side effect of turning the warning off completely in 'allmodconfig'
builds, which in turn led to a lot of warnings (both actual bugs, and
remaining false positives) to go in unnoticed.
With commit 877417e6ff ("Kbuild: change CC_OPTIMIZE_FOR_SIZE
definition") enabled the warning again for allmodconfig builds in v4.7
and in v4.8-rc1, I had finally managed to address all warnings I get in
an ARM allmodconfig build and most other maybe-uninitialized warnings
for ARM randconfig builds.
However, commit 6e8d666e92 ("Disable "maybe-uninitialized" warning
globally") was merged at the same time and disabled it completely for
all configurations, because of false-positive warnings on x86 that I had
not addressed until then. This caused a lot of actual bugs to get
merged into mainline, and I sent several dozen patches for these during
the v4.9 development cycle. Most of these are actual bugs, some are for
correct code that is safe because it is only called under external
constraints that make it impossible to run into the case that gcc sees,
and in a few cases gcc is just stupid and finds something that can
obviously never happen.
I have now done a few thousand randconfig builds on x86 and collected
all patches that I needed to address every single warning I got (I can
provide the combined patch for the other warnings if anyone is
interested), so I hope we can get the warning back and let people catch
the actual bugs earlier.
This reverts the change to disable the warning completely and for now
brings it back at the "make W=1" level, so we can get it merged into
mainline without introducing false positives. A follow-up patch enables
it on all levels unless some configuration option turns it off because
of false-positives.
Link: https://rusty.ozlabs.org/?p=232 [1]
Link: https://gcc.gnu.org/wiki/Better_Uninitialized_Warnings [2]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARC linux uses 2 distribution modes for common interrupts: round robin
mode (IDU_M_DISTRI_RR) and a simple destination mode (IDU_M_DISTRI_DEST).
The first one is used when more than 1 cores may handle a common interrupt
and the second one is used when only 1 core may handle a common interrupt.
However idu_irq_set_affinity() always sets IDU_M_DISTRI_RR for all affinity
values. But there is no sense in setting of such mode if only 1 core must
handle a common interrupt.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came up when reviewing code to address missing IRQ affinity
setting in AXS103 platform and/or implementing hierarchical IRQ domains
- smp_ipi_irq_setup() callers pass hwirq but in turn calls
request_percpu_irq() which expects a linux virq. So invoke
irq_find_mapping() to do the conversion
(also explicitify this in code by renaming the args appropriately)
- idu_of_init()/idu_cascade_isr() were similarly using linux virq where
hwirq is expected, so do the conversion using irqd_to_hwirq() helper
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: made changelog a bit concise a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For CONFIG_SERIAL_EARLYCON we need 800MHz for NPS SoC
The early console driver uses BASE_BAUD and not using dtb.
The default of 50MHz is NOT good for NPS SoC.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Today we register to plat_smp_ops.clear() method which actually
is acking the IPI.
However this is already taking care by our irqchip driver specifically
by the irq_chip.irq_eoi() method.
This is perfect timing where it should be done and no special handling
is needed at plat_smp_ops.clear().
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This has caused a bunch of build failures at a few sites, with GNU
2015.12 and older as the assembler seems to need -mlock to be able to
grok llock/scond instructions for ARC700 builds.
different places since the
older tools still seem to release
of tools which most people are using seem to trip with the -mlock flag
not being passed.
This reverts commit c300547588.
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
So better to write this in "C" anyways.
CC: stable@vger.kernel.org #4.2+
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original syscall only used to return errno to indicate if cmpxchg
succeeded. It was not returning the "previous" value which typical cmpxchg
callers are interested in to build their slowpaths or retry loops.
Given user preemption in syscall return path etc, it is not wise to
check this in userspace afterwards, but should be what kernel actually
observed in the syscall.
So change the syscall interface to always return the previous value and
additionally set Z flag to indicate whether operation succeeded or not
(just like ARM implementation when they used to have this syscall)
The flag approach avoids having to put_user errno which is nice given
the use case for this syscall cares mostly about the "previous" value.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to use generic implementation of dma_map_ops.mmap which is
dma_common_mmap() but that only worked for simpler cached mappings when
vaddr = paddr.
If a driver requests uncached DMA buffer kernel maps it to virtual
address so that MMU gets involved and page uncached status takes into
account. In that case usage of dma_common_mmap() lead to mapping of
vaddr to vaddr for user-space which is obviously wrong. For more detals
please refer to verbose explanation here [1].
So here we implement our own version of mmap() which always deals
with dma_addr and maps underlying memory to user-space properly
(note that DMA buffer mapped to user-space is always uncached
because there's no way to properly manage cache from user-space).
[1] https://lkml.org/lkml/2016/10/26/973
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> #4.5+
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
At smp_prepare_cpus() we set present cpu mask as part of init
for all CPUs at range [0-max_cpus].
This is done without checking if this mask is already being set.
At platform of eznps this mask is already being initialized at
smp_init_cpus() by using hook plat_smp_ops.init_early_smp().
So to avoid overriding of present cpu mask we check the number of
bits which are set in this mask. At the begin only bit for boot CPU
is set so if number of bits already set is no more than one we can be
assure that there is no overriding of this mask.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now when we have properly working performance counters in nSIM
even with interrupt support (fix should be a part of upcoming
nSIM engineering build 2016.12-005) we may enable perf support
by default for all platforms that use nSIM for ARC cores simulation.
Note 1: PCT node was missing for some reason in nsimosci.dts
while all other nSIM-related .dts files already had
PCT node for quite some time, so adding it now.
Note 2: All defconfigs were regenerated with "make savedefconfig"
which led to some clean-ups in nsimosci_hs_smp_defconfig:
CONFIG_FRAMEBUFFER_CONSOLE=y was removed because it is
automatically selected now by DRM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have referece to section name string table in
apply_relocate_add(), use it to
- print the name of section being relocated
- print symbol with NULL name (since it refers to a section)
before
| Section to fixup 7000a060
| =========================================================
| rela->r_off | rela->addend | sym->st_value | ADDR | VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 []
| 40 0 7000a000 7000a0a0 7000a000 []
after
| Section to fixup .eh_frame @7000a060
| =========================================================
| r_off r_add st_value ADDRESS VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 [.init.text]
| 40 0 7000a000 7000a0a0 7000a000 [.exit.text]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are really ancient toggles and tools no longer require them to be
passed. This paves way for deprecating them in long run.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Its all generic atomic_long_t stuff now.
Tested-by: Jason Low <jason.low2@hpe.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
if user disables IOC from debugger at startup (by clearing @ioc_enable),
@ioc_exists is cleared too. This means boot prints don't capture the
fact that IOC was present but disabled which could be misleading.
So invert how we use @ioc_enable and @ioc_exists and make it more
canonical. @ioc_exists represent whether hardware is present or not and
stays same whether enabled or not. @ioc_enable is still user driven,
but will be auto-disabled if IOC hardware is not present, i.e. if
@ioc_exist=0. This is opposite to what we were doing before, but much
clearer.
This means @ioc_enable is now the "exported" toggle in rest of code such
as dma mapping API.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Older ARC700 cores (ARC750 specifically) lack instructions to implement
atomic r-w-w. This is problematic for userspace libraries such as NPTL
which need atomic primitives. So enable them by providing kernel assist.
This is costly but really the only sane soluton (othern than tight
spinning using the otherwise availiable atomic exchange EX instruciton).
Good thing is there are only a few of these cores running Linux out in
the wild.
This only works on UP systems.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cast valid since TASK_SIZE * 2 will never actually cause overflow.
| CC fs/binfmt_elf.o
| In file included from ../include/linux/elf.h:4:0,
| from ../include/linux/module.h:15,
| from ../fs/binfmt_elf.c:12:
| ../fs/binfmt_elf.c: In function load_elf_binar:
| ../arch/arc/include/asm/elf.h:57:29: warning: integer overflow in expression [-Woverflow]
| #define ELF_ET_DYN_BASE (2 * TASK_SIZE / 3)
| ^
| ../fs/binfmt_elf.c:921:16: note: in expansion of macro ELF_ET_DYN_BASE
| load_bias = ELF_ET_DYN_BASE - vaddr;
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
num_possible_cpus() returns how many CPUs may be present on system.
However we want the highest possible CPU number.
This may be differ in a sparsed possible CPUs map.
Such map achived by OF for plat-eznps.
For example if we have:
possible cpus mask 0,3
Then:
num_possible_cpus() is equal 2
while
nr_cpu_ids is equal 4.
Only for value 4 c_start() will provide correct cpuinfo at procfs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add support for lzma compressed uImage.
Support for gzip was already available but could not be enabled because
we were missing CONFIG_HAVE_KERNEL_GZIP in arch/arc/Kconfig.
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The IDU intc is technically part of MCIP (Multi-core IP) hence
historically was only available in a SMP hardware build (and thus only
in a SMP kernel build). Now that hardware restriction has been lifted,
so a UP kernel needs to support it.
This requires breaking mcip.c into parts which are strictly SMP
(inter-core interrupts) and IDU which in reality is just another
intc and thus has no bearing on SMP.
This change allows IDU in UP builds and with a suitable device tree, we
can have the cascaded intc system
ARCv2 core intc <---> ARCv2 IDU intc <---> periperals
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d9676fa152 ("ARCv2: Enable LOCKDEP"), changed
local_save_flags() to not return raw STATUS32 but encoded in the form
such that it could be fed directly to CLRI/SETI instructions.
However the STATUS32.E[] was not captured correctly as it corresponds to
bits [4:1] in the register and not [3:0]
Fixes: d9676fa152 ("ARCv2: Enable LOCKDEP")
Cc: Evgeny Voevodin <evgeny.voevodin@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Seem like values assigned as absolute number and not and
shift value, i.e. should be 0 for one node (2^0) and 1 for
couple of nodes (2^1)
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In the end of "arc_init_IRQ" STATUS32.IE flag is going to be affected by
"flag" instruction but "flag" never touches IE flag on ARCv2. So "kflag"
instruction must be used instead of "flag".
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Cc: stable@vger.kernel.org #4.2+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to keep the .exit.* sections as linker would fail in final link
due to references from .debug_frame which itself could not be discardrd
due to the forced "write,alloc" attributes for it.
| LD init/built-in.o
| `.exit.text' referenced in section `.debug_frame' of arch/arc/built-in.o: defined in discarded section `.exit.text' of arch/arc/built-in.o
| Makefile:949: recipe for target 'vmlinux' failed
With .debug_frame now retired, this hack is no longer needed.
kernel binary is now a little bit smaller as well.
closes STAR 9000549913
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This uses a new set of annoations viz. ENTRY_CFI/END_CFI to enabel cfi
ops generation.
Note that we didn't change the normal ENTRY/EXIT as we don't actually
want unwind info in the trap/exception/interrutp handlers which use
these, as unwinder then gets confused (it keeps recursing vs. stopping).
Semantically these are leaf routines and unwinding should stop when it
hits those routines.
Before
------
28.52% 1.19% 9929 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--8.95%--EV_Trap
| --8.25%--sys_write
| |--3.93%--sock_write_iter
...
|--2.62%--memset <==== [LEAF entry as no unwind info]
^^^^^^
After
-----
29.46% 1.24% 13622 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--9.31%--EV_Trap
| --8.62%--sys_write
| |--4.17%--sock_write_iter
...
|--6.19%--sys_write
| --6.19%--sock_write_iter
| unix_stream_sendmsg
| |--1.62%--sock_alloc_send_pskb
| |--0.89%--sock_def_readable
| |--0.88%--_raw_spin_unlock_irqrestore
| |--0.69%--memset
| | ^^^^^^ <==== [now in proper callframe]
| |
| --0.52%--skb_copy_datagram_from_iter
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1. detect whether binutils supports the cfi pseudo ops
2. define conditional macros to generate the ops
3. define new ENTRY_CFI/END_CFI to annotate hand asm code.
- Needed because we don't want to emit dwarf info in general ENTRY/END
used by lowest level trap/exception/interrutp handlers as unwinder
gets confused trying to unwind out of them. We want unwinder to
instead stop when it hits onfo those routines
- These provide minimal start/end cfi ops assuming routine doesn't
touch stack memory/regs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This essentially removes ENTRY() assembler annotation for this symbol
since it didn't have a pairing END()
This in ahead of introducing cfi pseudo ops in ENTRY/END which expects
paired cfi_startproc/cfi_endproc
| ../arch/arc/kernel/entry.S: Assembler messages:
| ../arch/arc/kernel/entry.S:270: Error: previous CFI entry not closed (missing .cfi_endproc)
| ../scripts/Makefile.build:326: recipe for target 'arch/arc/kernel/entry-arcv2.o' failed
| make[4]: *** [arch/arc/kernel/entry-arcv2.o] Error 1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In .debug_frame based unwinding regime, we used to force -gdwarf-2 since
kernel unwinder only claimed to handle dwarf 2. This changed since commit
6d0d506012 ("ARC: dw2 unwind: Don't bail for CIE.version != 1")
which added some support beyond dwarf 2, atleast to handle CIE != 1
The ill-effect of -gdwarf-2 is that it forces generation of .debug_*
sections, which bloats loadable modules .ko files. For the curious, this
doesn't affect vmlinx binary since linker script discards .debug_* but
same discard is not yet implemented for modules.
So it seems we can drop the -gdwarf-2 toggle, which should not be needed
anyways given that we now use .eh_frame based unwinding.
I've verified using GNU 2016.09-engo10 that the actual unwind info is
not different with or w/o this toggle - but the debug_* sections are
gone for good.
before
-----
arc-linux-readelf -S q_proc.ko-unwinding-1-eh_frame-switch | grep debug
[15] .debug_info PROGBITS 00000000 000300 00d08d 00 0 0 1
[16] .rela.debug_info RELA 00000000 0162a0 008844 0c I 29 15 4
[17] .debug_abbrev PROGBITS 00000000 00d38d 0005f8 00 0 0 1
[18] .debug_loc PROGBITS 00000000 00d985 000070 00 0 0 1
[19] .rela.debug_loc RELA 00000000 01eae4 0000c0 0c I 29 18 4
[20] .debug_aranges PROGBITS 00000000 00d9f5 000040 00 0 0 1
[21] .rela.debug_arang RELA 00000000 01eba4 000030 0c I 29 20 4
[22] .debug_ranges PROGBITS 00000000 00da35 000018 00 0 0 1
[23] .rela.debug_range RELA 00000000 01ebd4 000030 0c I 29 22 4
[24] .debug_line PROGBITS 00000000 00da4d 000b5b 00 0 0 1
[25] .rela.debug_line RELA 00000000 01ec04 0000cc 0c I 29 24 4
[26] .debug_str PROGBITS 00000000 00e5a8 007831 01 MS 0 0 1
after
----
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
So finally after almost 8 years of dealing with .debug_frame, we are
finally switching to .eh_frame. The reason being stripped kernel
binaries had non-functional unwinder as .debug_frame was gone.
Also, in general .eh_frame seems more common way of doing unwinding.
This also folds a revert of f52e126cc7 ("ARC: unwind: ensure that
.debug_frame is generated (vs. .eh_frame)") to ensure that we start
getting .eh_frame
Reported-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to live with PERF_COUNT_HW_CACHE_REFERENCES and
PERF_COUNT_HW_CACHE_REFERENCES not specified on ARC.
Those events are actually aliases to 2 cache events that we do support
and so this change sets "cache-reference" and "cache-misses" events
in the same way as "L1-dcache-loads" and L1-dcache-load-misses.
And while at it adding debug info for cache events as well as doing a
subtle fix in HW events debug info - config value is much better
represented by hex so we may see not only event index but as well other
control bits set (if they exist).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Build brekeage since last changes to generic atomic operations.
Added couple of missing macros which are now mandatory
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARCv2 ISA provides 64-bit exclusive load/stores so use them to implement
the 64-bit atomics and elide the spinlock based generic 64-bit atomics
boot tested with atomic64 self-test (and GOD bless the person who wrote
them, I realized my inline assmebly is sloppy as hell)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cool thing is that same kernel image can run on
- nsim OSCI simulation platform
- SDPlite FPGA setups
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As it was discussed quite some time ago (see
https://lkml.org/lkml/2015/11/5/862) it's a good practice to add
"model" property in .dts. Moreover as per ePAPR "model" property is
required and should look like "manufacturer,model" so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On faulting sigreturn we do get SIGSEGV, all right, but anything
we'd put into pt_regs could end up in the coredump. And since
__copy_from_user() never zeroed on arc, we'd better bugger off
on its failure without copying random uninitialized bits of
kernel stack into pt_regs...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull uaccess fixes from Al Viro:
"Fixes for broken uaccess primitives - mostly lack of proper zeroing
in copy_from_user()/get_user()/__get_user(), but for several
architectures there's more (broken clear_user() on frv and
strncpy_from_user() on hexagon)"
* 'uaccess-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
avr32: fix copy_from_user()
microblaze: fix __get_user()
microblaze: fix copy_from_user()
m32r: fix __get_user()
blackfin: fix copy_from_user()
sparc32: fix copy_from_user()
sh: fix copy_from_user()
sh64: failing __get_user() should zero
score: fix copy_from_user() and friends
score: fix __get_user/get_user
s390: get_user() should zero on failure
ppc32: fix copy_from_user()
parisc: fix copy_from_user()
openrisc: fix copy_from_user()
nios2: fix __get_user()
nios2: copy_from_user() should zero the tail of destination
mn10300: copy_from_user() should zero on access_ok() failure...
mn10300: failing __get_user() and get_user() should zero
mips: copy_from_user() must zero the destination on access_ok() failure
ARC: uaccess: get_user to zero out dest in cause of fault
...
Add ARC as an arch that supports PCI_MSI_IRQ_DOMAIN and add generation of
msi.h in the ARC arch.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Some module using div_u64() was failing to link because the libgcc 64-bit
divide assist routine was not being exported for modules
Reported-by: avinashp@quantenna.com
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
| CC mm/memory.o
| In file included from ../mm/memory.c:53:0:
| ../include/linux/pfn_t.h: In function ‘pfn_t_pte’:
| ../include/linux/pfn_t.h:78:2: error: conversion to non-scalar type requested
| return pfn_pte(pfn_t_to_pfn(pfn), pgprot);
With STRICT_MM_TYPECHECKS pte_t is a struct and the offending code
forces a cast which ends up shifting a struct and hence the gcc warning.
Note that in recent past some of the arches (aarch64, s390) made
STRICT_MM_TYPECHECKS default, but we don't for ARC as this leads to slightly
worse generated code, given ARC ABI definition of returning structs
(which pte_t would become)
Quoting from ARC ABI...
"Results of type struct are returned in a caller-supplied temporary
variable whose address is passed in r0.
For such functions, the arguments are shifted so that they are
passed in r1 and up."
So
- struct to be returned would be allocated on stack requiring extra
code at call sites
- callee updates stack memory to facilitate the return (vs. simple
MOV into return reg r0)
Hence STRICT_MM_TYPECHECKS is not enabled by default for ARC
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
Cc: <stable@vger.kernel.org>
Signed-off-by: Liav Rehana <liavr@mellanox.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: rewrote title and commit log]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For resources shared by all cores such as SLC and IOC, only the master
core needs to do any setups / enabling / disabling etc.
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
trace_hardirqs_on_caller() in lockdep.c expects to be called before, not
after interrupts are actually enabled.
The following comment in kernel/locking/lockdep.c substantiates this
claim:
"
/*
* We're enabling irqs and according to our state above irqs weren't
* already enabled, yet we find the hardware thinks they are in fact
* enabled.. someone messed up their IRQ state tracing.
*/
"
An example can be found in include/linux/irqflags.h:
do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0)
Without this change, we hit the following DEBUG_LOCKS_WARN_ON.
[ 7.760000] ------------[ cut here ]------------
[ 7.760000] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2711 resume_user_mode_begin+0x48/0xf0
[ 7.770000] DEBUG_LOCKS_WARN_ON(!irqs_disabled())
[ 7.780000] Modules linked in:
[ 7.780000] CPU: 0 PID: 1 Comm: init Not tainted 4.7.0-00003-gc668bb9-dirty #366
[ 7.790000]
[ 7.790000] Stack Trace:
[ 7.790000] arc_unwind_core.constprop.1+0xa4/0x118
[ 7.800000] warn_slowpath_fmt+0x72/0x158
[ 7.800000] resume_user_mode_begin+0x48/0xf0
[ 7.810000] ---[ end trace 6f6a7a8fae20d2f0 ]---
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
LTP madvise05 was generating mm splat
| [ARCLinux]# /sd/ltp/testcases/bin/madvise05
| BUG: Bad page map in process madvise05 pte:80e08211 pmd:9f7d4000
| page:9fdcfc90 count:1 mapcount:-1 mapping: (null) index:0x0 flags: 0x404(referenced|reserved)
| page dumped because: bad pte
| addr:200b8000 vm_flags:00000070 anon_vma: (null) mapping: (null) index:1005c
| file: (null) fault: (null) mmap: (null) readpage: (null)
| CPU: 2 PID: 6707 Comm: madvise05
And for newer kernels, the system was rendered unusable afterwards.
The problem was mprotect->pte_modify() clearing PTE_SPECIAL (which is
set to identify the special zero page wired to the pte).
When pte was finally unmapped, special casing for zero page was not
done, and instead it was treated as a "normal" page, tripping on the
map counts etc.
This fixes ARC STAR 9001053308
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Several build configurations had already disabled this warning because
it generates a lot of false positives. But some had not, and it was
still enabled for "allmodconfig" builds, for example.
Looking at the warnings produced, every single one I looked at was a
false positive, and the warnings are frequent enough (and big enough)
that they can easily hide real problems that you don't notice in the
noise generated by -Wmaybe-uninitialized.
The warning is good in theory, but this is a classic case of a warning
that causes more problems than the warning can solve.
If gcc gets better at avoiding false positives, we may be able to
re-enable this warning. But as is, we're better off without it, and I
want to be able to see the *real* warnings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXlRXSAAoJEHm+PkMAQRiGG/gH/0Z8O4zWOsrwO+X1mRToRDBH
joFOjAmCVe83T1VpF5LYNB+9+owL/dEDt6+ZIswnhH7AfQPjs4RqwS4PcuMbCDVO
+mDm0PmfcKaYcQZrB2Z2OwIzRNnfCTVcsDPhIHwuIHk0m4z/xuGZonD8KoAj0+tO
3yJF6sbE1KubDVjOb+lmZZSP3cXA0pDXrNhkYhE4Tsr8fiihGjeXSNJ8t2zPLjxo
W3MPqo0rzDvQsOwoF4TWHHagVaFSJlhLBBgqu33fI7uO3jtfQD2G8wG68JCND1j3
qbMoBfTLFV/yQmSIJUt0Wv1axaCcwnjpweEB35A/GEeZ0mNB1rDdoBeI1eKEQkc=
=DGFC
-----END PGP SIGNATURE-----
Backmerge tag 'v4.7' into drm-next
Linux 4.7
As requested by Daniel Vetter as the conflicts were getting messy.
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Pull locking updates from Ingo Molnar:
"The locking tree was busier in this cycle than the usual pattern - a
couple of major projects happened to coincide.
The main changes are:
- implement the atomic_fetch_{add,sub,and,or,xor}() API natively
across all SMP architectures (Peter Zijlstra)
- add atomic_fetch_{inc/dec}() as well, using the generic primitives
(Davidlohr Bueso)
- optimize various aspects of rwsems (Jason Low, Davidlohr Bueso,
Waiman Long)
- optimize smp_cond_load_acquire() on arm64 and implement LSE based
atomic{,64}_fetch_{add,sub,and,andnot,or,xor}{,_relaxed,_acquire,_release}()
on arm64 (Will Deacon)
- introduce smp_acquire__after_ctrl_dep() and fix various barrier
mis-uses and bugs (Peter Zijlstra)
- after discovering ancient spin_unlock_wait() barrier bugs in its
implementation and usage, strengthen its semantics and update/fix
usage sites (Peter Zijlstra)
- optimize mutex_trylock() fastpath (Peter Zijlstra)
- ... misc fixes and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
locking/atomic: Introduce inc/dec variants for the atomic_fetch_$op() API
locking/barriers, arch/arm64: Implement LDXR+WFE based smp_cond_load_acquire()
locking/static_keys: Fix non static symbol Sparse warning
locking/qspinlock: Use __this_cpu_dec() instead of full-blown this_cpu_dec()
locking/atomic, arch/tile: Fix tilepro build
locking/atomic, arch/m68k: Remove comment
locking/atomic, arch/arc: Fix build
locking/Documentation: Clarify limited control-dependency scope
locking/atomic, arch/rwsem: Employ atomic_long_fetch_add()
locking/atomic, arch/qrwlock: Employ atomic_fetch_add_acquire()
locking/atomic, arch/mips: Convert to _relaxed atomics
locking/atomic, arch/alpha: Convert to _relaxed atomics
locking/atomic: Remove the deprecated atomic_{set,clear}_mask() functions
locking/atomic: Remove linux/atomic.h:atomic_fetch_or()
locking/atomic: Implement atomic{,64,_long}_fetch_{add,sub,and,andnot,or,xor}{,_relaxed,_acquire,_release}()
locking/atomic: Fix atomic64_relaxed() bits
locking/atomic, arch/xtensa: Implement atomic_fetch_{add,sub,and,or,xor}()
locking/atomic, arch/x86: Implement atomic{,64}_fetch_{add,sub,and,or,xor}()
locking/atomic, arch/tile: Implement atomic{,64}_fetch_{add,sub,and,or,xor}()
locking/atomic, arch/sparc: Implement atomic{,64}_fetch_{add,sub,and,or,xor}()
...
page should be calculated using physical address.
If platform uses non-trivial dma-to-phys memory translation,
dma_handle should be converted to physicval address before
calculation of page.
Failing to do so results in struct page * pointing to
wrong or non-existent memory.
Fixes: f2e3d55397 ("ARC: dma: reintroduce platform specific dma<->phys")
Cc: stable@vger.kernel.org #4.6+
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull the clockevents/clocksource tree from Daniel Lezcano:
- Convert the clocksource-probe init functions to return a value in order to
prepare the consolidation of the drivers using the DT. It is a big patchset
but went through 01.org (kbuild bot), linux next and kernel-ci (continuous
integration) (Daniel Lezcano)
- Fix a bad error handling by returning the right value for cadence_ttc
(Christophe Jaillet)
- Fix typo in the Kconfig for the Samsung pwm (Alexandre Belloni)
- Change functions to static for armada-370-xp and digicolor (Ben Dooks)
- Add support for the rk3399 SoC timer by adding bindings and a slight
change in the base address. Take the opportunity to add the DYNIRQ flag
(Huang Tao)
- Fix endian accessors for the Samsung pwm timer (Matthew Leach)
- Add Oxford Semiconductor RPS Dual Timer driver (Neil Armstrong)
- Add a kernel parameter to swich on/off the event stream feature of the arch
arm timer (Will Deacon)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
- Reinstate dwarf unwinder/loadable-modules with new gnu tools
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ABub
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fix from Vineet Gupta:
"Reinstate dwarf unwinder/loadable-modules with new gnu tools"
* tag 'arc-4.7-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: unwind: warn only once if DW2_UNWIND is disabled
ARC: unwind: ensure that .debug_frame is generated (vs. .eh_frame)
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.
This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)
The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables
.eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables
.debug_frame generated with -gdwarf-2
Fixes STAR 9001058196
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
pte_alloc_one_kernel uses __get_order_pte but this is obviously always
zero because BITS_FOR_PTE is not larger than 9 yet the page size is
always larger than 4K. This means that this flag has never been
actually useful here because it has always been used only for
PAGE_ALLOC_COSTLY requests.
Link: http://lkml.kernel.org/r/1464599699-30131-7-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Since all architectures have this implemented now natively, remove this
dead code.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement FETCH-OP atomic primitives, these are very similar to the
existing OP-RETURN primitives we already have, except they return the
value of the atomic variable _before_ modification.
This is especially useful for irreversible operations -- such as
bitops (because it becomes impossible to reconstruct the state prior
to modification).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch updates/fixes all spin_unlock_wait() implementations.
The update is in semantics; where it previously was only a control
dependency, we now upgrade to a full load-acquire to match the
store-release from the spin_unlock() we waited on. This ensures that
when spin_unlock_wait() returns, we're guaranteed to observe the full
critical section we waited on.
This fixes a number of spin_unlock_wait() users that (not
unreasonably) rely on this.
I also fixed a number of ticket lock versions to only wait on the
current lock holder, instead of for a full unlock, as this is
sufficient.
Furthermore; again for ticket locks; I added an smp_rmb() in between
the initial ticket load and the spin loop testing the current value
because I could not convince myself the address dependency is
sufficient, esp. if the loads are of different sizes.
I'm more than happy to remove this smp_rmb() again if people are
certain the address dependency does indeed work as expected.
Note: PPC32 will be fixed independently
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: chris@zankel.net
Cc: cmetcalf@mellanox.com
Cc: davem@davemloft.net
Cc: dhowells@redhat.com
Cc: james.hogan@imgtec.com
Cc: jejb@parisc-linux.org
Cc: linux@armlinux.org.uk
Cc: mpe@ellerman.id.au
Cc: ralf@linux-mips.org
Cc: realmz6@gmail.com
Cc: rkuo@codeaurora.org
Cc: rth@twiddle.net
Cc: schwidefsky@de.ibm.com
Cc: tony.luck@intel.com
Cc: vgupta@synopsys.com
Cc: ysato@users.sourceforge.jp
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in nSIM OSCI virtual platforms
with modern Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in HS38 VDK with modern
Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This reverts commit e78fdfef84.
The issue was fixed in hardware in HS2.1C release and there are no known
external users of affected RTL so revert the whole delayed retry series !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This reverts commit b89aa12c17.
The issue was fixed in hardware in HS2.1C release and there are no known
external users of affected RTL so revert the whole delayed retry series !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This reverts commit 1097163870.
The issue was fixed in hardware in HS2.1C release and there are no known
external users of affected RTL - so revert thw whole delayed retry
series !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 support for 2 interrupt priorities historically allowed even slow
perpherals such as emac and uart to setup high priority interrupts
which was wrong from the beginning as they could possibly delay the more
critical timer interrupt.
The hardware support for 2 level interrupts in ARCompact is less than
ideal anyways (judging from the "hacks" in low level entry code and thus
is not used in productions systems I know of.
So reduce the scope of this to timer only, thereby reducing a bunch of
complexity.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now when we switched to usage of real clk devices for CPU core
frequency those root properties make no sense any longer.
Se we're just getting rid of them here to not confuse readers of
our .dts files.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Christian Ruppert <christian.ruppert@alitech.com>
Cc: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull perf updates from Ingo Molnar:
"Mostly tooling and PMU driver fixes, but also a number of late updates
such as the reworking of the call-chain size limiting logic to make
call-graph recording more robust, plus tooling side changes for the
new 'backwards ring-buffer' extension to the perf ring-buffer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
perf record: Read from backward ring buffer
perf record: Rename variable to make code clear
perf record: Prevent reading invalid data in record__mmap_read
perf evlist: Add API to pause/resume
perf trace: Use the ptr->name beautifier as default for "filename" args
perf trace: Use the fd->name beautifier as default for "fd" args
perf report: Add srcline_from/to branch sort keys
perf evsel: Record fd into perf_mmap
perf evsel: Add overwrite attribute and check write_backward
perf tools: Set buildid dir under symfs when --symfs is provided
perf trace: Only auto set call-graph to "dwarf" when syscalls are being traced
perf annotate: Sort list of recognised instructions
perf annotate: Fix identification of ARM blt and bls instructions
perf tools: Fix usage of max_stack sysctl
perf callchain: Stop validating callchains by the max_stack sysctl
perf trace: Fix exit_group() formatting
perf top: Use machine->kptr_restrict_warned
perf trace: Warn when trying to resolve kernel addresses with kptr_restrict=1
perf machine: Do not bail out if not managing to read ref reloc symbol
perf/x86/intel/p4: Trival indentation fix, remove space
...
I have only one patch for asm-generic in this release, this one is from
James Hogan and updates the generic system call table for renameat2
so we don't need to provide both renameat and renameat2 in newly
added architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ae81
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanup from Arnd Bergmann:
"I have only one patch for asm-generic in this release, this one is
from James Hogan and updates the generic system call table for
renameat2 so we don't need to provide both renameat and renameat2 in
newly added architectures"
* tag 'asm-generic-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: Drop renameat syscall from default list
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
The binary GCD algorithm is based on the following facts:
1. If a and b are all evens, then gcd(a,b) = 2 * gcd(a/2, b/2)
2. If a is even and b is odd, then gcd(a,b) = gcd(a/2, b)
3. If a and b are all odds, then gcd(a,b) = gcd((a-b)/2, b) = gcd((a+b)/2, b)
Even on x86 machines with reasonable division hardware, the binary
algorithm runs about 25% faster (80% the execution time) than the
division-based Euclidian algorithm.
On platforms like Alpha and ARMv6 where division is a function call to
emulation code, it's even more significant.
There are two variants of the code here, depending on whether a fast
__ffs (find least significant set bit) instruction is available. This
allows the unpredictable branches in the bit-at-a-time shifting loop to
be eliminated.
If fast __ffs is not available, the "even/odd" GCD variant is used.
I use the following code to benchmark:
#include <stdio.h>
#include <stdlib.h>
#include <stdint.h>
#include <string.h>
#include <time.h>
#include <unistd.h>
#define swap(a, b) \
do { \
a ^= b; \
b ^= a; \
a ^= b; \
} while (0)
unsigned long gcd0(unsigned long a, unsigned long b)
{
unsigned long r;
if (a < b) {
swap(a, b);
}
if (b == 0)
return a;
while ((r = a % b) != 0) {
a = b;
b = r;
}
return b;
}
unsigned long gcd1(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
b >>= __builtin_ctzl(b);
for (;;) {
a >>= __builtin_ctzl(a);
if (a == b)
return a << __builtin_ctzl(r);
if (a < b)
swap(a, b);
a -= b;
}
}
unsigned long gcd2(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
r &= -r;
while (!(b & r))
b >>= 1;
for (;;) {
while (!(a & r))
a >>= 1;
if (a == b)
return a;
if (a < b)
swap(a, b);
a -= b;
a >>= 1;
if (a & r)
a += b;
a >>= 1;
}
}
unsigned long gcd3(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
b >>= __builtin_ctzl(b);
if (b == 1)
return r & -r;
for (;;) {
a >>= __builtin_ctzl(a);
if (a == 1)
return r & -r;
if (a == b)
return a << __builtin_ctzl(r);
if (a < b)
swap(a, b);
a -= b;
}
}
unsigned long gcd4(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
r &= -r;
while (!(b & r))
b >>= 1;
if (b == r)
return r;
for (;;) {
while (!(a & r))
a >>= 1;
if (a == r)
return r;
if (a == b)
return a;
if (a < b)
swap(a, b);
a -= b;
a >>= 1;
if (a & r)
a += b;
a >>= 1;
}
}
static unsigned long (*gcd_func[])(unsigned long a, unsigned long b) = {
gcd0, gcd1, gcd2, gcd3, gcd4,
};
#define TEST_ENTRIES (sizeof(gcd_func) / sizeof(gcd_func[0]))
#if defined(__x86_64__)
#define rdtscll(val) do { \
unsigned long __a,__d; \
__asm__ __volatile__("rdtsc" : "=a" (__a), "=d" (__d)); \
(val) = ((unsigned long long)__a) | (((unsigned long long)__d)<<32); \
} while(0)
static unsigned long long benchmark_gcd_func(unsigned long (*gcd)(unsigned long, unsigned long),
unsigned long a, unsigned long b, unsigned long *res)
{
unsigned long long start, end;
unsigned long long ret;
unsigned long gcd_res;
rdtscll(start);
gcd_res = gcd(a, b);
rdtscll(end);
if (end >= start)
ret = end - start;
else
ret = ~0ULL - start + 1 + end;
*res = gcd_res;
return ret;
}
#else
static inline struct timespec read_time(void)
{
struct timespec time;
clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &time);
return time;
}
static inline unsigned long long diff_time(struct timespec start, struct timespec end)
{
struct timespec temp;
if ((end.tv_nsec - start.tv_nsec) < 0) {
temp.tv_sec = end.tv_sec - start.tv_sec - 1;
temp.tv_nsec = 1000000000ULL + end.tv_nsec - start.tv_nsec;
} else {
temp.tv_sec = end.tv_sec - start.tv_sec;
temp.tv_nsec = end.tv_nsec - start.tv_nsec;
}
return temp.tv_sec * 1000000000ULL + temp.tv_nsec;
}
static unsigned long long benchmark_gcd_func(unsigned long (*gcd)(unsigned long, unsigned long),
unsigned long a, unsigned long b, unsigned long *res)
{
struct timespec start, end;
unsigned long gcd_res;
start = read_time();
gcd_res = gcd(a, b);
end = read_time();
*res = gcd_res;
return diff_time(start, end);
}
#endif
static inline unsigned long get_rand()
{
if (sizeof(long) == 8)
return (unsigned long)rand() << 32 | rand();
else
return rand();
}
int main(int argc, char **argv)
{
unsigned int seed = time(0);
int loops = 100;
int repeats = 1000;
unsigned long (*res)[TEST_ENTRIES];
unsigned long long elapsed[TEST_ENTRIES];
int i, j, k;
for (;;) {
int opt = getopt(argc, argv, "n:r:s:");
/* End condition always first */
if (opt == -1)
break;
switch (opt) {
case 'n':
loops = atoi(optarg);
break;
case 'r':
repeats = atoi(optarg);
break;
case 's':
seed = strtoul(optarg, NULL, 10);
break;
default:
/* You won't actually get here. */
break;
}
}
res = malloc(sizeof(unsigned long) * TEST_ENTRIES * loops);
memset(elapsed, 0, sizeof(elapsed));
srand(seed);
for (j = 0; j < loops; j++) {
unsigned long a = get_rand();
/* Do we have args? */
unsigned long b = argc > optind ? strtoul(argv[optind], NULL, 10) : get_rand();
unsigned long long min_elapsed[TEST_ENTRIES];
for (k = 0; k < repeats; k++) {
for (i = 0; i < TEST_ENTRIES; i++) {
unsigned long long tmp = benchmark_gcd_func(gcd_func[i], a, b, &res[j][i]);
if (k == 0 || min_elapsed[i] > tmp)
min_elapsed[i] = tmp;
}
}
for (i = 0; i < TEST_ENTRIES; i++)
elapsed[i] += min_elapsed[i];
}
for (i = 0; i < TEST_ENTRIES; i++)
printf("gcd%d: elapsed %llu\n", i, elapsed[i]);
k = 0;
srand(seed);
for (j = 0; j < loops; j++) {
unsigned long a = get_rand();
unsigned long b = argc > optind ? strtoul(argv[optind], NULL, 10) : get_rand();
for (i = 1; i < TEST_ENTRIES; i++) {
if (res[j][i] != res[j][0])
break;
}
if (i < TEST_ENTRIES) {
if (k == 0) {
k = 1;
fprintf(stderr, "Error:\n");
}
fprintf(stderr, "gcd(%lu, %lu): ", a, b);
for (i = 0; i < TEST_ENTRIES; i++)
fprintf(stderr, "%ld%s", res[j][i], i < TEST_ENTRIES - 1 ? ", " : "\n");
}
}
if (k == 0)
fprintf(stderr, "PASS\n");
free(res);
return 0;
}
Compiled with "-O2", on "VirtualBox 4.4.0-22-generic #38-Ubuntu x86_64" got:
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 10174
gcd1: elapsed 2120
gcd2: elapsed 2902
gcd3: elapsed 2039
gcd4: elapsed 2812
PASS
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 9309
gcd1: elapsed 2280
gcd2: elapsed 2822
gcd3: elapsed 2217
gcd4: elapsed 2710
PASS
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 9589
gcd1: elapsed 2098
gcd2: elapsed 2815
gcd3: elapsed 2030
gcd4: elapsed 2718
PASS
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 9914
gcd1: elapsed 2309
gcd2: elapsed 2779
gcd3: elapsed 2228
gcd4: elapsed 2709
PASS
[akpm@linux-foundation.org: avoid #defining a CONFIG_ variable]
Signed-off-by: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.
This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.
[akpm@linux-foundation.org: fix mips]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge updates from Andrew Morton:
- fsnotify fix
- poll() timeout fix
- a few scripts/ tweaks
- debugobjects updates
- the (small) ocfs2 queue
- Minor fixes to kernel/padata.c
- Maybe half of the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm, page_alloc: restore the original nodemask if the fast path allocation failed
mm, page_alloc: uninline the bad page part of check_new_page()
mm, page_alloc: don't duplicate code in free_pcp_prepare
mm, page_alloc: defer debugging checks of pages allocated from the PCP
mm, page_alloc: defer debugging checks of freed pages until a PCP drain
cpuset: use static key better and convert to new API
mm, page_alloc: inline pageblock lookup in page free fast paths
mm, page_alloc: remove unnecessary variable from free_pcppages_bulk
mm, page_alloc: pull out side effects from free_pages_check
mm, page_alloc: un-inline the bad part of free_pages_check
mm, page_alloc: check multiple page fields with a single branch
mm, page_alloc: remove field from alloc_context
mm, page_alloc: avoid looking up the first zone in a zonelist twice
mm, page_alloc: shortcut watermark checks for order-0 pages
mm, page_alloc: reduce cost of fair zone allocation policy retry
mm, page_alloc: shorten the page allocator fast path
mm, page_alloc: check once if a zone has isolated pageblocks
mm, page_alloc: move __GFP_HARDWALL modifications out of the fastpath
mm, page_alloc: simplify last cpupid reset
mm, page_alloc: remove unnecessary initialisation from __alloc_pages_nodemask()
...
I've just discovered that the useful-sounding has_transparent_hugepage()
is actually an architecture-dependent minefield: on some arches it only
builds if CONFIG_TRANSPARENT_HUGEPAGE=y, on others it's also there when
not, but on some of those (arm and arm64) it then gives the wrong
answer; and on mips alone it's marked __init, which would crash if
called later (but so far it has not been called later).
Straighten this out: make it available to all configs, with a sensible
default in asm-generic/pgtable.h, removing its definitions from those
arches (arc, arm, arm64, sparc, tile) which are served by the default,
adding #define has_transparent_hugepage has_transparent_hugepage to
those (mips, powerpc, s390, x86) which need to override the default at
runtime, and removing the __init from mips (but maybe that kind of code
should be avoided after init: set a static variable the first time it's
called).
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Ning Qu <quning@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [arch/s390]
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
- Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy domains)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pnAx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
The most recent release of AXS103 [v1.1] is proven to work
at 100 MHz in dual-core mode so this change uses mentioned feature.
For that we:
* Update axc003_idu.dtsi with mention of really-used CPU clock freq
* Remove clock override in AXS platform code for dual-core HW
Note we're still leaving a hack for clock "downgrade" on early boot
for quad-core hardware.
Also note this change will break functionality of AXS103 v1.0 hardware.
That means all users of AXS103 __must__ upgrade their boards with the
most recent firmware.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
This makes perf_callchain_{user,kernel}() receive the max stack
as context for the perf_callchain_entry, instead of accessing
the global sysctl_perf_event_max_stack.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/n/tip-kolmn1yo40p7jhswxwrc7rrd@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Please pull this mini-series that allows ARC PGU to use
dedicated memory location as framebuffer backing storage.
* 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux:
ARC: [axs10x] Specify reserved memory for frame buffer
drm/arcpgu: use dedicated memory area for frame buffer
The default 256 bytes sometimes is just not enough.
We usually provide earlycon=... and console=... and ip=...
All this and more may need more room.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Since the CTOP is SMT hardware multi-threaded, we need to hint
the HW that now will be a very good time to do a hardware
thread context switching. This is done by issuing the schd.rw
instruction (binary coded here so as to not require specific
revision of GCC to build the kernel).
sched.rw means that Thread becomes eligible for execution by
the threads scheduler after all pending read/write
transactions were completed.
Implementing cpu_relax_lowlatency() with barrier()
Since with current semantics of cpu_relax() it may take a
while till yielded CPU will get back.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
With generic "identity" num of CPUs is limited to 256 (8 bit).
We use our alternative AUX register GLOBAL_ID (12 bit).
Now we can support up to 4096 CPUs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
NPS device got 256 cores and each got 16 HW threads (SMT).
We use EZchip dedicated ISA to trigger HW scheduler of the
core that current HW thread belongs to.
This scheduling makes sure that data beyond barrier is available
to all HW threads in core and by that to all in device (4K).
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
We need our own implementaions since we lack LLSC support.
Our extended ISA provided with optimized solution for all 32bit
operations we see in these three headers.
Signed-off-by: Noam Camus <noamc@ezchip.com>
NPS use special mapping right below TASK_SIZE.
Hence we need to lower STACK_TOP so that user stack won't
overlap NPS special mapping.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
In SMP setup, master loops for each_present_cpu calling cpu_up().
For ARC it returns as soon as new cpu's status becomes online,
However secondary may still do HW initializing,
machine or platform hook level.
So turn secondary online only after all HW setup is done.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
If we hold rwlock and interrupt occures we may
end up spinning on it for ever during softirq.
Note that this lock is an internal lock
and since the lock is free to be used from any context,
the lock needs to be IRQ-safe.
Below you may see an example for interrupt we get while
nl_table_lock is holding its rw->lock_mutex and we spinned
on it for ever.
The concept for the fix was taken from SPARC.
[2015-05-12 19:16:12] Stack Trace:
[2015-05-12 19:16:12] arc_unwind_core+0xb8/0x11c
[2015-05-12 19:16:12] dump_stack+0x68/0xac
[2015-05-12 19:16:12] _raw_read_lock+0xa8/0xac
[2015-05-12 19:16:12] netlink_broadcast_filtered+0x56/0x35c
[2015-05-12 19:16:12] nlmsg_notify+0x42/0xa4
[2015-05-12 19:16:13] neigh_update+0x1fe/0x44c
[2015-05-12 19:16:13] neigh_event_ns+0x40/0xa4
[2015-05-12 19:16:13] arp_process+0x46e/0x5a8
[2015-05-12 19:16:13] __netif_receive_skb_core+0x358/0x500
[2015-05-12 19:16:13] process_backlog+0x92/0x154
[2015-05-12 19:16:13] net_rx_action+0xb8/0x188
[2015-05-12 19:16:13] __do_softirq+0xda/0x1d8
[2015-05-12 19:16:14] irq_exit+0x8a/0x8c
[2015-05-12 19:16:14] arch_do_IRQ+0x6c/0xa8
[2015-05-12 19:16:14] handle_interrupt_level1+0xe4/0xf0
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
On ARC, lower 2G of address space is translated and used for
- user vaddr space (region 0 to 5)
- unused kernel-user gutter (region 6)
- kernel vaddr space (region 7)
where each region simply represents 256MB of address space.
The kernel vaddr space of 256MB is used to implement vmalloc, modules
So far this was enough, but not on EZChip system with 4K CPUs (given
that per cpu mechanism uses vmalloc for allocating chunks)
So allow VMALLOC_SIZE to be configurable by expanding down into the unused
kernel-user gutter region which at default 256M was excessive anyways.
Also use _BITUL() to fix a build error since PGDIR_SIZE cannot use "1UL"
as called from assembly code in mm/tlbex.S
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: rewrote changelog, debugged bootup crash due to int vs. hex]
Acked-by: Vineet Gupta <vgupta@synopsys.com>
UAPI header should not use Kconfig items
Use __BIG_ENDIAN__ defined as a compiler intrinsic
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: fix changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
