The new general dummy stubs for MMD register access were introduced.
Use that for the codes reuse.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 2b2427d064 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.
Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix obvious typo that first return value is set but not checked.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an
autoneg failure case by resetting the hardware. This turns off
intterupts. Things will work themselves out if the phy polls, as it will
figure out it's state during a poll. However if the phy uses only
intterupts, the phy will stall, since interrupts are off. This patch
fixes the issue by calling config_intr after resetting the phy.
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg ")
Signed-off-by: Zach Brown <zach.brown@ni.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.
This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding Microchip 9477 Phy included in KSZ9477 Switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fa8cddaf90 ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 99f81afc13.
It was papering over the real problem, which is fixed by commit
f555f34fdc ("net: phy: fix auto-negotiation stall due to unavailable
interrupt")
Signed-off-by: David S. Miller <davem@davemloft.net>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the command:
ethtool --phy-statistics eth0
will cause system crash with meassage "Unable to handle kernel NULL pointer
dereference at virtual address 00000010" from:
(kszphy_get_stats) from [<c069f1d8>] (ethtool_get_phy_stats+0xd8/0x210)
(ethtool_get_phy_stats) from [<c06a0738>] (dev_ethtool+0x5b8/0x228c)
(dev_ethtool) from [<c06b5484>] (dev_ioctl+0x3fc/0x964)
(dev_ioctl) from [<c0679f7c>] (sock_ioctl+0x170/0x2c0)
(sock_ioctl) from [<c02419d4>] (do_vfs_ioctl+0xa8/0x95c)
(do_vfs_ioctl) from [<c02422c4>] (SyS_ioctl+0x3c/0x64)
(SyS_ioctl) from [<c0107d60>] (ret_fast_syscall+0x0/0x44)
The reason: phy_driver structure for KSZ9031 phy has no .probe() callback
defined. As result, struct phy_device *phydev->priv pointer will not be
initializes (null).
This issue will affect also following phys:
KSZ8795, KSZ886X, KSZ8873MLL, KSZ9031, KSZ9021, KSZ8061, KS8737
Fix it by:
- adding .probe() = kszphy_probe() callback to KSZ9031, KSZ9021
phys. The kszphy_probe() can be re-used as it doesn't do any phy specific
settings.
- removing statistic callbacks from other phys (KSZ8795, KSZ886X,
KSZ8873MLL, KSZ8061, KS8737) as they doesn't have corresponding
statistic counters.
Fixes: 2b2427d064 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert micrel to the new read_mmd/write_mmd driver methods. This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pr commit "net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause"
this phy driver should not set these feature bits.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Fixes: 9d162ed69f ("net: phy: micrel: add support for KSZ8795")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is adds support for the PHYs in the KSZ8795 5port managed switch.
It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix setting of SUPPORTED_FIBRE bit as it was not present in features
of KSZ8041.
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set bit 0 in register 1C.23 to enable the EDPD feature of the
KSZ9031 PHY. This reduces power consumption when the link is
down.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable all interrupts when suspend, they will be enabled
when resume. Otherwise, the suspend/resume process will be
blocked occasionally.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable auto negotiation on init to properly detect an already plugged
cable at boot.
At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.
It was working properly before 321beec504 (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.
Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.
This fixes resuming which is failing on the xplained boards from atmel
since 321beec504 (net: phy: Use interrupts when available in NOLINK
state)
Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 651df21835 ("phy: micrel: Fix finding PHY properties in MAC
node.") only fixes finding PHY properties in MAC node for KSZ9021. This
commit applies the same fix for KSZ9031.
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Suggested-by: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very rarely, the KSZ9031 will appear to complete autonegotiation, but
will drop all traffic afterwards. When this happens, the idle error
count will read 0xFF after autonegotiation completes. Reset the PHY
when in that state.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some defines for a few pad skew related extended registers.
Specify for which MMD Address (dev_addr) they are for.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few places in this driver, we weren't using const where we could
have. Use const more.
In addition, change the arrays of strings in ksz9031_config_init() to be
not only const, but also static.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do clock-mode-select if clk == NULL,
since when building without CONFIG_HAVE_CLK,
clk_get returns NULL and clk_get_rate returns 0.
Doing clock-mode-select in this cause causes kszphy_probe to
return -EINVAL and thus prevents the device from being probed.
The original code (before regression) would return 0
when building without CONFIG_HAVE_CLK.
Cc: stable <stable@vger.kernel.org> # 3.18+
Fixes: 1fadee0c36 ("net/phy: micrel: Add clock support for
KSZ8021/KSZ8031")
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Niklas Cassel <niklass@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode for all Micrel PHYs
using IRQ line as a NAND-tree toggle mode at reset.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic config_init callback also for KSZ8021 and KSZ8031.
This has been avoided this far due to commit b838b4aced ("phy/micrel:
KSZ8031RNL RMII clock reconfiguration bug"), which claims that the PHY
becomes unresponsive if the broadcast-disable flag is set before
configuring the clock mode.
Turns out that the problem seemingly worked-around by the above
mentioned commit was really due to a hardware-configuration issue, where
the PHY was in fact strapped to address 3 rather than 0.
Tested-by: Bruno Thomsen <bth@kamstrup.dk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic interrupt-config callback and store interrupt-level bitmask
in type data for PHY types not using bit 9.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel KSZ8081 and KSZ8091 PHYs have the RMII Reference Clock Select
bit, which is used to select 25 or 50 MHz clock mode.
Note that on some revisions of the PHY (e.g. KSZ8081RND) the function of
this bit is inverted so that setting it enables 25 rather than 50 MHz
mode. Add a new device-tree property
"micrel,rmii-reference-clock-select-25-mhz" to describe this.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic RMII-Reference-Clock-Select support.
Several Micrel PHY have an RMII-Reference-Clock-Select bit to select
25 MHz or 50 MHz clock mode. Recently, support for configuring this
through device tree for KSZ8021 and KSZ8031 was added.
Generalise this support so that it can be configured for other PHY types
as well.
Note that some PHY revisions (of the same type) has this bit inverted.
This should be either configurable through a new device-tree property,
or preferably, determined based on PHY ID if possible.
Also note that this removes support for setting 25 MHz mode from board
files which was also added by the above mentioned commit 45f56cb82e45
("net/phy: micrel: Add clock support for KSZ8021/KSZ8031").
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
