efx_nic_fatal_interrupt() disables DMA before scheduling a reset.
After this, we need not and *cannot* flush queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a bug fix for an "interface fails to load" issue.
The issue occurs when bnx2x driver loads after UNDI driver was previously
loaded over the chip. In such a scenario the UNDI driver is loaded and operates
in the pre-boot kernel, within its own specific host memory address range.
When the pre-boot stage is complete, the real kernel is loaded, in a new and
distinct host memory address range. The transition from pre-boot stage to boot
is asynchronous from UNDI point of view.
A race condition occurs when UNDI driver triggers a DMAE transaction to valid
host addresses in the pre-boot stage, when control is diverted to the real
kernel. This results in access to illegal addresses by our HW as the addresses
which were valid in the preboot stage are no longer considered valid.
Specifically, the 'was_error' bit in the pci glue of our device is set. This
causes all following pci transactions from chip to host to timeout (in
accordance to the pci spec).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.
This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the REQ and GNT bit in the eeprom control register (EECD).
This is required if the eeprom is to be accessed with auto read
EERD register.
After a cold reset this doesn't matter but if PBIST MAC test was
executed before booting, the register was left in a dirty state
(the 2 bits where set), which caused the read operation to time out
and returning 0.
Reference (page 312):
http://download.intel.com/design/network/manuals/316080.pdf
Reported-by: Aleksandar Igic <aleksandar.igic@dektech.com.au>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Like other supported (igp) PHYs, the driver needs to be able to force the
master/slave mode on 82577. Since the code is the same as what already
exists in the code flow for igp PHYs, move it to a new function to be
called for both flows.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: John Bishop <johnx.bishop@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB. Previously we would
have to call the fc_enable call 8 times, once for each packet buffer. If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.
This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10. This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can avoid many of the forward declarations found in ixgbe_common.c by
just reordering things so this patch does that to help cleanup the code.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the calls to put_page with calls to __free_page.
Since the FCoE code is able to access order 1 pages I thought it would be a
good idea to change things over to using __free_pages since that is the
preferred approach for freeing pages.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that ixgbe_fc_autoneg is a void and always sets the
current_mode. Previously if the link was down we would return an error,
however there is no harm in simply treating a link down case as a case in
which autoneg simply failed. This allows us to rely on the return value of
the ixgbe_fc_enable call now since there should be no cases where it
returns an error that would normally be ignored.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change reorders the mapping of rings to q_vectors in the case that the
number of rings exceeds the number of q_vectors. Previously we would
allocate the first R/N queues to the first q_vector where R is the number
of rings and N is the number of q_vectors. Instead of doing this we can do
a better job of interleaving the rings to the CPUs by assigning every Nth
ring to the q_vector.
The below tables illustrate this change for the R = 16 N = 4 case.
Before patch After patch
q_vector: 0 1 2 3 0 1 2 3
Rings: 0 4 8 12 0 1 2 3
1 5 9 13 4 5 6 7
3 6 10 14 8 9 10 11
4 7 11 15 12 13 14 15
This should improve the performance for both DCB or ATR when the number of
rings exceeds the number of q_vectors allocated by the adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can track instances of where a packet was
dropped due to a packet being received when there are no DMA buffers
available in the ring.
For some reason this was only being enabled with RSC, however it makes
more sense to always have this feature on so that we can track any cases
where we might drop a buffer due to an Rx ring being full.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Version bump to 1.11.3-k.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The idea here seems to be to get a 44bit DMA mask working and if this
fails it should fallback to a 32bit DMA mask. The dma_mask variable is
assigned once to 44bit and never updated. pci_set_dma_mask() and
pci_set_consistent_dma_mask() are both implemented as functions so there
is no evil macro which might update dma_mask. Looking at the assembly, I
see a call to dma_set_mask() followed by dma_supported() and then a jump
passed the second dma_set_mask(). The only way to get to second
dma_set_mask() call is by an error code in the first one.
So I hereby remove the check since it looks superfluous. Please ignore
the path if there is black magic involved.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this commit:
commit aacc1bea19
Author: Multanen, Eric W <eric.w.multanen@intel.com>
Date: Wed Mar 28 07:49:09 2012 +0000
ixgbe: driver fix for link flap
The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.
We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was possible for shutdown to pull the rug out from other driver entry
points. Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Hariharan Nagarajan <hanagara@cisco.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the Physical Function (PF) resets after the VF has set jumbo
frame MTU then the VF jumbo frame is overwritten. Make sure the
VF driver always requests proper MTU size after reset
synchronization.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 10Gig controller is capable of linking at 100Mbits - add
support for reporting that link speed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the 82573, ASPM L1 gets disabled wholesale so this special-case code
is not required. For the 82574 the previous patch does the same as for
the 82573, disabling L1 on the adapter. Thus, this code is no longer
required and can be removed.
Signed-off-by: Chris Boot <bootc@bootc.net>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ASPM on the 82574 causes trouble. Currently the driver disables L0s for
this NIC but only disables L1 if the MTU is >1500. This patch simply
causes L1 to be disabled regardless of the MTU setting.
Signed-off-by: Chris Boot <bootc@bootc.net>
Cc: "Wyborny, Carolyn" <carolyn.wyborny@intel.com>
Cc: Nix <nix@esperi.org.uk>
Link: https://lkml.org/lkml/2012/3/19/362
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, IPv6 extension header parsing was disabled for all devices
supported by e1000e when using packet split mode. However, as per a
silicon errata, only certain devices need this restriction and will need
to disable IPv6 extension header parsing for all modes.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For 82574 and 82583 devices, resolve an intermittent link issue where
the link negotiates to 100Mbps rather than 1Gbps when powering off the
PHY and powering on the PHY after several seconds.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the locked versions of the read/write PHY ops function pointers
often produces excessively long lines. Shorten these as is done with
the non-locked versions of the PHY register read/write functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a known issue in the 82577 and 82578 device that can cause a hang
in the device hardware during traffic stress; the current workaround in the
driver is to disable transmit flow control by default. If the user enables
transmit flow control and the device hang occurs, provide a message in the
syslog suggesting to re-enable the workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While testing the TCP changes I had to fix an issue in order to be able to
load and unload the module.
The recent patch that added thermal sensor support added a use after free
bug on module unload with an 82598 adapter in the system. To resolve the
issue I have updated the code so that when we free the info_kobj we set it
back to NULL.
I suspect there are likely other bugs present, but I will leave that for
another patch that can undergo more testing.
I am submitting this directly to net-next since this fixes a fairly serious
bug that will lock up the ixgbe module until the system is rebooted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting
gp->wake_on_lan to bool. Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An EEH error can cause the FW to trigger a flash debug dump.
Resetting the card while flash dump is in progress can cause it not to recover.
Wait for it to finish before letting EEH flow to reset the card.
Signed-off-by: Sathya Perla <Sathya.Perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sarveshwar Bandi <Sarveshwar.Bandi@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renders the interface view somewhat inconsistent from the Host OS POV
considering the rest of the interfaces are showing their respective speeds
based on the bandwidth assigned to them.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this compiler warning (on PowerPC) by not marking a parameter as
const:
drivers/net/ethernet/pasemi/pasemi_mac.c: In function 'pasemi_mac_replenish_rx_ring':
drivers/net/ethernet/pasemi/pasemi_mac.c:646:3: warning: passing argument 1 of 'netdev_alloc_skb' discards qualifiers from pointer target type
include/linux/skbuff.h:1706:31: note: expected 'struct net_device *' but argument is of type 'const struct net_device *'
Cc: Olof Johansson <olof@lixom.net>
Cc: Pradeep A. Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 30a5de7723 added
ability to use single MSI-X vector, but lack proper
handling for 57710/57711 HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user request for the number of VFs in the max_vfs parameter is
out of range then reset the value to the default value of zero. This
makes the behavior of the ixgbe driver the same as for the igb driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the host VMM administrator has set the virtual function device's
MAC address then also deny VF requests for MACVLAN filters.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Garrett, Robert <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have thermal data available, this patch exports
this data via hwmon sysfs interface.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some 82599 adapters contain thermal data that we can get to via
an i2c interface. These functions provide support to get at that
data. A following patch will export this data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY initialization flows and assorted workarounds for 82577/8/9 done
during driver load and resume from Sx should be the same yet they are not.
Combine the current flows/workarounds into a common set of functions that
are called during the different code paths.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An update to the EEPROM on 82579 will extend a delay in hardware to fix an
issue with WoL not working after a G3->S5 transition which is unrelated to
the driver. However, this extended delay conflicts with nominal operation
of the device when it is initialized by the driver and after every reset
of the hardware (i.e. the driver starts configuring the device before the
hardware is done with it's own configuration work). The workaround for
when the driver is in control of the device is to tell the hardware after
every reset the configuration delay should be the original shorter one.
Some pre-existing variables are renamed generically to be re-used with
new register accesses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
