Clean up led-mode setup by introducing proper defines for PHY Control
registers 1 and 2 and only passing the register to the setup function.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure never to update more than two bits when setting the led mode,
something which could for example change the reference-clock setting.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable PHY address 0 as the broadcast address, so that it can be used
as a unique (non-broadcast) address on a shared bus.
Note that this can also be configured using the B-CAST_OFF pin on
KSZ9091, but that KSZ8081 lacks this pin and is also limited to
addresses 0 and 3.
Specifically, this allows for dual KSZ8081 setups.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and clean up broadcast disable.
Some Micrel PHYs have a broadcast-off bit in the Operation Mode Strap
Override register which can be used to disable PHY address 0 as the
broadcast address, so that it can be used as a unique (non-broadcast)
address on a shared bus.
Note that the KSZPHY_OMSO_RMII_OVERRIDE bit is set by default on
KSZ8021/8031.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure never to update the control register with random data (an
error code) by checking the return value after reading it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_driver_register with
module_phy_driver macro.
Compile tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When advertised capabilities are changed with mii-tool, such as:
mii-tool -A 10baseT
the existing handler has two errors.
- An actual PHY register value is provided by mii-tool, and this
must be mapped to internal state with mii_adv_to_ethtool_adv_t().
- The PHY state machine needs to be told that autonegotiation has
again been performed. If not, the MAC will not be notified of
the new link speed and duplex, resulting in a possible config
mismatch.
Signed-off-by: Brian Hill <Brian@houston-radar.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe-phy driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to sync the states of the PCS and the PHY
after a reset is performed. If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a sysfs binary file is asked to be removed, it is found by
attribute name, so strictly speaking this change is not a fix, but
just in case when attribute name is changed in the driver or sysfs
internals are changed, it might be better to remove the previously
created file using right the same binary attribute.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell phy 88E1145 configuration & initialization was missing a case
for initializing SGMII mode. This patch adds that case.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional code to m88e1145_config_init function to allow the driver to
support SGMII mode.
Signed-off-by: Viet Nga Dao <vndao@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E3016 is a FastEthernet PHY that also can be found in Marvell
Berlin SoCs as integrated PHY.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: Unable to send and receive Ethernet packets with Micrel PHY.
Affected devices:
KSZ8031RNL (commercial temp)
KSZ8031RNLI (industrial temp)
Description:
PHY device is correctly detected during probe.
PHY power-up default is 25MHz crystal clock input
and output 50MHz RMII clock to MAC.
Reconfiguration of PHY to input 50MHz RMII clock from MAC
causes PHY to become unresponsive if clock source is changed
after Operation Mode Strap Override (OMSO) register setup.
Cause:
Long lead times on parts where clock setup match circuit design
forces the usage of similar parts with wrong default setup.
Solution:
Swapped KSZ8031 register setup and added phy_write return code validation.
Tested with Freescale i.MX28 Fast Ethernet Controler (fec).
Signed-off-by: Bruno Thomsen <bth@kamstrup.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz
and 50MHz. Both PHYs differ in the default frequency they expect
after reset. If this differs from the actual input clock, then
register 0x1f bit 7 must be changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust fixed_phy_register() to return struct phy_device *, so that
it becomes easy to use fixed PHYs without device tree support:
phydev = fixed_phy_register(PHY_POLL, &fixed_phy_status, NULL);
fixed_phy_set_link_update(phydev, fixed_phy_link_update);
phy_connect_direct(netdev, phydev, handler_fn, phy_interface);
This change is a prerequisite for modifying bcmgenet driver to work
without a device tree on Broadcom's MIPS-based 7xxx platforms.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_BCM_UNIMAC needs HAS_IOMEM, so depend on it, the related error (
with allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap" [drivers/net/phy/mdio-bcm-unimac.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the GENET and SF2 drivers have been updated to communicate us
what is the revision of the BCM7xxx integrated PHY, utilize that
information in the config_init() callback to call into the appropriate
workaround function based on our revision.
While at it, we also print the revision and patch level to help debug
new chips.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for the PHY driver to check PHY_BRCM_100MBPS_WAR since
that is redundant with checking the PHY device supported features. Get
rid of that workaround flag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9031 appears to suffer from the same hardware bug as described
for the KSZ9021 in commit 32fcafbcd1
("net/phy: micrel: Disable asymmetric pause for KSZ9021")
you have to unplug the cable and plug it back to get it to work.
Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dp83640_remove can use skb_queue_purge
instead of looping through itself to flush any entries out of the queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-sun4i driver automatically selects REGULATOR and
REGULATOR_FIXED_VOLTAGE because it uses the regulator API. But a
driver selecting a subsystem increases the chance of generating
circular Kconfig dependencies, especially when other drivers depend on
the selected symbol.
Since the regulator API functions are replaced with no-ops when
REGULATOR is disabled, the driver can be built successfully even
without regulator support and so those 'select' dependencies can be
safely dropped.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch inadvertently deleted a declaration in the
amd_xgbe_an_tx_training function causing the build to fail.
Add the declaration for 'priv' back to the function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy timestamping takes a different path than the regular timestamping
does in that it will create a clone first so that the packets needing to be
timestamped can be placed in a queue, or the context block could be used.
In order to support these use cases I am pulling the core of the code out
so it can be used in other drivers beyond just phy devices.
In addition I have added a destructor named sock_efree which is meant to
provide a simple way for dropping the reference to skb exceptions that
aren't part of either the receive or send windows for the socket, and I
have removed some duplication in spots where this destructor could be used
in place of sock_edemux.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is. Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/mdio-bcm-unimac.c:195:37-38: unimac_mdio_ids is not NULL
terminated at line 195
Make sure of_device_id tables are NULL terminated
Generated by: scripts/coccinelle/misc/of_table.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal PHYs may not have a valid PHY interface defined, which will
show up in sysfs as "". Add an explicit check of internal PHYs to report
their interface correctly.
Fixes: 3d055d8d1c ("net: phy: expose PHY device interface mode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new entries to the Broadcom BCM7xxx internal PHY driver for
BCM7250 and BCM7364 chips. Those chips share the usual 28nm process
Gigabit PHY sequence and require the same workarounds so far.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 28nm Gigabit PHYs supported by the driver have the same
callbacks, the only differences being the 32-bits OUI and the name. Use
a macro to factor this, making it easier in the future to add new
entries.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Std 802.3az if the EEE Adv (Reg 7.60), Link partner ability
(Reg 7.61) and EEE capability (Register 3.20) bits return 0 this means no EEE
is supported. So this patch fixes the checks inside the phy_init_eee function.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.
Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal PHYs do not have any specific phy_interface_t defined because
they are within an Ethernet MAC or a larger IC, they will fail the early
check in phy_init_eee(). Allow these PHYs to proceed with EEE
initialization and report error/success by checking the standard C45
EEE-related registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.
Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fixed PHY driver does not properly emulate Clause 45 over Clause 22
MDIO reads, and as such, will return bogus values when we access such
registers.
Return an error when accessing these registers in order to prevent
advertising bogus capabilities such as EEE support and such.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 28nm process BCM7xxx internal Gigabit PHYs all support automatic
power down, turn on that feature as part of the configuration
initialization callback.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 439d39a9ac ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bare register numbers are used despite <uapi/linux/mdio.h> has MDIO_DEVS[12]
#define'd for those.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Event timestamp status messages have a variable length, ranging from
1 to 5 words (16 bit words). The current code however requires
a minimum message length of sizeof(*phy_txts). In most cases this
condition is fulfilled due to padding bytes. However, if several events
are signaled in a single message, padding bytes may not be present.
For short event timestamp status messages, the length check will fail,
and the event timestamp will be dropped.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the one hand, phy_device.c provides a generic reset function if the phy
driver does not provide a soft_reset pointer. This generic reset does not take
into account the state of the phy, with a potential failure if the phy is in
powerdown mode. On the other hand, smsc driver provides a function with both
correct reset behaviour and configuration.
This patch moves the reset part into a new smsc_phy_reset function and provides
the soft_reset pointer to have a correct reset behaviour by default.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a71e3c3796 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:
root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>] lr : [<80361f44>] psr: 600f0013
sp : bceb7d70 ip : bceb7d88 fp : bceb7d84
r10: 8091523c r9 : 00000000 r8 : bd88f478
r7 : 803f8a88 r6 : 81165988 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : bd88f478 r0 : bd88f478
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 4cd1404a DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....
The problem with the original commit is explained by Russell King:
"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.
Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."
This reverts commit a71e3c3796.
Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a label is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present. Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel ksz9021 PHY does not support standard IEEE standard MMD
extended register access, therefore requires stubs to fail the read
register method and do nothing for the write register method when
libphy attempts to read and/or configure Energy Efficient Ethernet
features in PHYS that do support those features. This problem
was observed on an Altera Cyclone V SOC development kit that
uses the Synopsys EMAC and the Micrel ksz9021 PHY. This patch
was tested on the same board, and Energy Efficient Ethernet is
now disabled as expected since the Micrel PHY does not support that
feature.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy was originally written assuming all phy devices support clause 45
access extensions to the mmd registers through the indirection registers
located within the first 16 phy registers. This assumption is not true
in all cases, and one specific example is the Micrel ksz9021 10/100/1000
Mbps phy. Using the stmmac driver, accessing the mmd registers to query
and configure energy efficient Ethernet (EEE) features yielded unexpected
behavior.
This patch adds mmd access functions to the phy driver that can be
overriden by the phy specific driver if the phy does not support this
mechanism or uses it's own non-standard access mechanism. By default,
the IEEE Compatible clause 45 access mechanism described in clause 22
is used. With this patch, EEE query/configure functions as expected
using the stmmac and the Micrel ksz9021 phy.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the logic will loop endlessly waiting for a rate change
to complete. Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
moved the call to phy_scan_fixups() in phy_init_hw() after a software
reset is performed.
By the time phy_init_hw() is called in phy_device_register(), no driver
has been bound to this PHY yet, so all the checks in phy_init_hw()
against the PHY driver and the PHY driver's config_init function will
return 0. We will therefore never call phy_scan_fixups() as we should.
Fix this by calling phy_scan_fixups() and check for its return value to
restore the intended functionality.
This broke PHY drivers which do register an early PHY fixup callback to
intercept the PHY probing and do things like changing the 32-bits unique
PHY identifier when a pseudo-PHY address has been used, as well as
board-specific PHY fixups that need to be applied during driver probe
time.
Reported-by: Hauke Merthens <hauke-m@hauke-m.de>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds proper module_{get,put} to prevent the MDIO bus module
from being unloaded while the phydev is connected. By doing so, we fix
a kernel panic produced when a MDIO driver is removed, but the phydev
that relies on it is attached and running.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register() registers a device which is already bound to a driver.
Hence, the driver pointer should be set properly in order to track down
the driver associated to the MDIO bus.
This will be used to allow ethernet driver to pin down a MDIO bus driver,
preventing it from being unloaded while the PHY device is running.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When timestamping received packets, rx_timestamp_work may be scheduled
before the timestamps is received from the hardware resulting in the
packet beeing delivered without the timestamp.
This is fixed by changing the receive timestamp path:
On receiving a packet that need timestamping, the rxts list is
traversed. If a match is found, packet+timestamp are delivered,
otherwise the packet is added to a rx_queue.
When a timestamp arrives rx_queue is traversed and if a matching
packet is found, it is delivered with the timestamp. Otherwise the
timestamp is added to the rxts list for matching with packets arriving
later.
In case the hardware drops a timestamp, a workqueue regularly checks
the queue for old packets and delivers them without a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the phy speed/duplex settings array to support more
than just baseT features. This change adds entries to support
the following additional speed/duplex/media types:
SUPPORTED_10000baseKR_Full
SUPPORTED_10000baseKX4_Full
SUPPORTED_2500baseX_Full
SUPPORTED_1000baseKX_Full
Additionally, it changes the 10GbE baseT entry from using the
hardcoded value 10000 to the SPEED_10000 define.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Event timestamp values should be adjusted by 3*reference clock period +
11 ns = 35 ns to compensate for input path and synchronization delays.
So subtract 35ns from event timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.
Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are two commonly used helper functions that
need to be exported for Ethernet drivers to be built as modules
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Periodic output triggers 0 and 1 of the dp83640 has a programmable
duty-cycle which is controlled by the Pulsewidth2 field of the trigger
data register. This field is not documented in the datasheet, but it
is described in the "PHYTER Software Development Guide" section
3.1.4.1. Failing to set the field can result in unstable/no trigger
output.
Add programming of the Pulsewidth2 field, setting it to the same value
as the Pulsewidth field for a 50% duty cycle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/at803x.c:196:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following compilation warning:
[...]
CC drivers/net/phy/amd-xgbe-phy.o
drivers/net/phy/amd-xgbe-phy.c:1353:30: warning:
‘amd_xgbe_phy_ids’ defined but not used [-Wunused-variable]
static struct mdio_device_id amd_xgbe_phy_ids[] = {
^
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to walk the list of subnodes of a mdio bus and look for
a node that matches the phy's address with its 'reg' property. If found,
set the of_node pointer for the phy. This allows auto-probed pyh
devices to be augmented by information passed in via DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. of_set_phy_supported is
called right after phy_device_register in the assumption that
phy_probe is called from phy_device_register and the features
of the phy are already initialized. For the genphy driver this
is not true, here phy_probe is called later during phy_connect
time. phy_probe will then overwrite all settings done from
of_set_phy_supported
Fix this by moving of_set_phy_supported to the core phy code
and calling it from phy_probe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing fixed_phy_add() function has several drawbacks that
prevents it from being used as is for OF-based declaration of fixed
PHYs:
* The address of the PHY on the fake bus needs to be passed, while a
dynamic allocation is desired.
* Since the phy_device instantiation is post-poned until the next
mdiobus scan, there is no way to associate the fixed PHY with its
OF node, which later prevents of_phy_connect() from finding this
fixed PHY from a given OF node.
To solve this, this commit introduces fixed_phy_register(), which will
allocate an available PHY address, add the PHY using fixed_phy_add()
and instantiate the phy_device structure associated with the provided
OF node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the fixed_phy_add() function was taking as argument
'phy_id', which was used both as the PHY address on the fake fixed
MDIO bus, and as the PHY id, as available in the MII_PHYSID1 and
MII_PHYSID2 registers. However, those two informations are completely
unrelated.
This patch decouples them. The PHY id of fixed PHYs is hardcoded to be
0x0. Ideally, a really reserved value would be nicer, but there
doesn't seem to be an easy of making sure a dummy value can be
assigned to the Linux kernel for such usage.
The PHY address remains passed by the caller of phy_fixed_add().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as
Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4
Only call phy_resume if phy_init_hw was successful.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6d48f44b7b "mdio_bus: implement devm_mdiobus_alloc/devm_mdiobus_free"
introduced a new function devm_mdiobus_alloc_size() but added an export
for a different function devm_mdiobus_alloc(), which was obviously
a simple mistake that leads to build error whenever this function is
used from a loadable module:
ERROR: "devm_mdiobus_alloc_size" [drivers/net/ethernet/ti/davinci_mdio.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
