Add pitch length info of graphics/video layer, pitch is used
to represent line length in byte, the usage depends on pix_fmt.
If the fmt is YUV, the pitch[0] will be Y length,pitch[1]
will be U length, pitch[2] will be V lenth.
If the fmt is RGB, the picth[0] will be line lenth, and
pitch[1]/pitch[2] will be 0 and not be used.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Reviewed-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new func mmpfb_set_win to make code clean, it will do resolution
and fmt setting of win in mmpfb_set_win.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Reviewed-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There are dumplicate code of the smooth setting based on different
path, optimized the routine and use readl_relaxed instead.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Guoqing Li <ligq@marvell.com>
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Reviewed-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We could set rb swap in two modules: DMA controler input part and
dsi interface output part.
DMA input part is based on pix_fmt to set rbswap, dsi output interface
part will set rbswap based on platform dsi_rbswap configuration.
This patch include below change and enhancement:
1) The input format which support rbswap is based on RGB format,
eg. RGB565 indicates the source data in memory is that Red is [15~11],
Green is [10~5], Blue is [4:0], Red is MSB, Blue is LSB, but for the
display dma input default setting(rbswap = 0), it only support Blue
is [15~11], Green is [10~5], Red is [4:0], Red is LSB, Blue is MSB,
so for this format(RGB565), display controller need to set rbswap
= 1 and it can support the MSB/LSB correctly.
BGR/YUV format will not set it in mmp display driver.
2) The dsi output part of rbswap is depend on dsi_rbswap which is
defined in specific platfrom. For output dsi interface, it has this
feature to do rbswap again if it needs specifc byte sequence of RGB
byte for DSI panel.
eg. If display content is set RGB565 in memory and DMA input part set
rbswap in driver to support Red as MSB , Blue LSB, but dsi panel only
support Red as LSB, Blue as MSB, then it can use this feature.
If there is no this requirement of panel, this dsi output part is not
needed.
Signed-off-by: Guoqing Li <ligq@marvell.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Reviewed-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Also, unnecessary casting from return value that is a void pointer
is removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The power management code is only used on X86 and PowerMac. To prevent
the compiler from warning about unused code, only build when PM and one
of X86 or PowerMac is selected.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
module_platform_driver removes some boilerplate code and makes
it simple.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removing some boilerplate by using module_i2c_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Also removed a useless comment as suggested by Jean Delvare.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
From 9e2c37ee1d5c2145fac113c483c9e6dd408f10fe Mon Sep 17 00:00:00 2001
From: Jingoo Han <jg1.han@samsung.com>
Date: Thu, 12 Sep 2013 15:11:07 +0900
Subject: [PATCH 14/21] video: pm2fb: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
From fbb1885952efb15a46d03aac050c38fc9179594e Mon Sep 17 00:00:00 2001
From: Jingoo Han <jg1.han@samsung.com>
Date: Thu, 12 Sep 2013 14:42:45 +0900
Subject: [PATCH 06/21] video: gx1fb: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable. Also, use the pci_power_t
value instead of always using the raw value for PCI_D2.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have a bug with omapdrm, where omapdrm calls dispc's pm_runtime
function in atomic context, and dispc's pm_runtime is not marked as
irq_safe:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:952
Dispc's runtime PM callbacks are irq safe, so we can just set the
irq_safe flag to fix the issue.
However, in the long term, I'd rather have omapdrm manage the runtime PM
calls in a better way. Calling get/put for every small operation that
touches the dispc registers is very inefficient. It'd be better and
cleaner to have clear "in-use" and "not-in-use" states for dispc, so
that we don't need to do register context restore for small operations,
only to turn dispc off right afterwards.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While using HDMI connector driver with sil9022 encoder
came across issue where connector driver is probed first.
This resulted in error. A deffered probe solved this.
Most connector drivers need a encoder driver as their
video source. This patch ensures we do a probe defferal
if video source is not present for connector drivers.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts the Linux for Workgroups thing. And no, before somebody
asks, we're not doing Linux95. Not for a few years, at least.
Sure, the flag added some color to the logo, and could have remained as
a testament to my leet gimp skills. But no. And I'll do this early, to
avoid the chance of forgetting when I'm doing the actual rc1 release on
the road.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
acornfb checks for HAS_VIDC while support for that macro was removed in
v2.6.23 (when the arm26 port was removed). So we can remove a bit of
dead code.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While cross-building for PPC64 I've got
WARNING: drivers/video/built-in.o(.text+0x9f9ca): Section mismatch in
reference from the function .ps3fb_probe() to th e variable
.init.data:ps3fb_fix The function .ps3fb_probe() references the
variable __initdata ps3fb_fix. This is often because .ps3fb_probe
lacks a __initdata annotation or the annotation of ps3fb_fix is wrong.
WARNING: drivers/video/built-in.o(.text+0x9f9d2): Section mismatch in
reference from the function .ps3fb_probe() to the variable
.init.data:ps3fb_fix The function .ps3fb_probe() references the
variable __initdata ps3fb_fix. This is often because .ps3fb_probe
lacks a __initdata annotation or the annotation of ps3fb_fix is wrong.
WARNING: drivers/built-in.o(.text+0xe222a): Section mismatch in
reference from the function .ps3fb_probe() to the variable
.init.data:ps3fb_fix The function .ps3fb_probe() references the
variable __initdata ps3fb_fix. This is often because .ps3fb_probe
lacks a __initdata annotation or the annotation of ps3fb_fix is wrong.
WARNING: drivers/built-in.o(.text+0xe2232): Section mismatch in
reference from the function .ps3fb_probe() to the variable
.init.data:ps3fb_fix The function .ps3fb_probe() references the
variable __initdata ps3fb_fix. This is often because .ps3fb_probe
lacks a __initdata annotation or the annotation of ps3fb_fix is wrong.
WARNING: vmlinux.o(.text+0x561d4a): Section mismatch in reference from
the function .ps3fb_probe() to the variable .init.data:ps3fb_fix The
function .ps3fb_probe() references the variable __initdata ps3fb_fix.
This is often because .ps3fb_probe lacks a __initdata annotation or
the annotation of ps3fb_fix is wrong.
Mismatch was introduced with 48c68c4f "Drivers: video: remove __dev*
attributes."
Remove __init data annotation from ps3fb_fix.
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
* Improvements to da8xx-fb to make it support v2 of the LCDC IP, used e.g. in
BeagleBone
* Himax HX8369 controller support
* Various small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Kr2i
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
- Improvements to da8xx-fb to make it support v2 of the LCDC IP, used
eg in BeagleBone
- Himax HX8369 controller support
- Various small fixes and cleanups
* tag 'fbdev-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (42 commits)
video: da8xx-fb: fix the polarities of the hsync/vsync pulse
video: da8xx-fb: support lcdc v2 timing register expansion
video: da8xx-fb: fixing timing off by one errors
video: da8xx-fb fixing incorrect porch mappings
video: xilinxfb: replace devm_request_and_ioremap by devm_ioremap_resource
fbmem: move EXPORT_SYMBOL annotation next to symbol declarations
drivers: video: fbcmap: remove the redundency and incorrect checkings
video: mxsfb: simplify use of devm_ioremap_resource
Release efifb's colormap in efifb_destroy()
at91/avr32/atmel_lcdfb: prepare clk before calling enable
video: exynos: Ensure definitions match prototypes
OMAPDSS: fix WARN_ON in 'alpha_blending_enabled' sysfs file
OMAPDSS: HDMI: Fix possible NULL reference
video: da8xx-fb: adding am33xx as dependency
video: da8xx-fb: let compiler decide what to inline
video: da8xx-fb: make clock naming consistent
video: da8xx-fb: set upstream clock rate (if reqd)
video: da8xx-fb: reorganize panel detection
video: da8xx-fb: ensure non-null cfg in pdata
video: da8xx-fb: use devres
...
* Change the OMAP board files to use the new OMAP display drivers
* Remove all the old drivers, and the related auxiliary code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Hj7U
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.12-omap-legacy-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP specific fbdev changes from Tomi Valkeinen:
"I've got this pull request separate from the main fbdev pull request,
as this contains a bunch of OMAP board file changes and thus could
possibly be rejected in case of bad conflicts.
The removal of the old display drivers depend on the board file
changes, so Tony Lindgren suggested taking them together via fbdev
tree. These are in linux-next, and also Tony didn't see any conflicts
with any of the branches he had, so they should go in clean.
- Change the OMAP board files to use the new OMAP display drivers
- Remove all the old drivers, and the related auxiliary code"
* tag 'fbdev-3.12-omap-legacy-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: rename omap_dss_device's 'device' field to 'dst'
OMAPDSS: rename omap_dss_device's 'output' to 'src'
OMAPDSS: DSS: remove legacy dss bus support
OMAPDSS: RFBI: remove code related to old panel model
OMAPDSS: VENC: remove code related to old panel model
OMAPDSS: SDI: remove code related to old panel model
OMAPDSS: DSI: remove code related to old panel model
OMAPDSS: HDMI: remove code related to old panel model
OMAPDSS: DPI: remove code related to old panel model
OMAPDSS: remove all old panel drivers
OMAPDSS: DPI: change regulator handling
OMAPDSS: SDI: change regulator handling
OMAPDSS: fix DPI and SDI device ids
OMAPDSS: remove omap_dss_device->channel field
OMAPDSS: RFBI: Mark RFBI as broken
ARM: OMAP2+: Remove old display drivers from omap2plus_defconfig
ARM: OMAP: AM3517EVM: use new display drivers
ARM: OMAP: Zoom: use new display drivers
ARM: OMAP: Pandora: use new display drivers
ARM: OMAP: OMAP3EVM: use new display drivers
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Pull x86 fb changes from Ingo Molnar:
"This tree includes preparatory patches for SimpleDRM driver support,
by David Herrmann. They clean up x86 framebuffer support by creating
simplefb devices wherever possible. More background can be found at
http://lwn.net/Articles/558104/"
* 'x86-fb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fbdev: fbcon: select VT_HW_CONSOLE_BINDING
fbdev: efifb: bind to efi-framebuffer
fbdev: vesafb: bind to platform-framebuffer device
fbdev: simplefb: add common x86 RGB formats
x86: sysfb: move EFI quirks from efifb to sysfb
x86: provide platform-devices for boot-framebuffers
fbdev: simplefb: mark as fw and allocate apertures
fbdev: simplefb: add init through platform_data
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
The polarities were being set to active low when fbdev was requesting active
high. This patch reverses it so that what is set into the LCD controller is
correct.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TI LCD controller version 2 adds some extra bits in a register to
increase the available size to represent horizontal timings. This
patch allows the fbdev driver to utilize those extra bits.
This will become important for driving an HDMI encoder from the lcd
controller where some of the VESA/CEA modes require quite large porches.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The LCD controller represents some of the timing fields with a 0
in the register representing 1. This was not taken into account
when these registers were being set. Interestingly enough not
all of the LCDC controller timing registers implement this representation
so carefully went through the technical reference manual to only "fix"
the correct timings.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver was mapping the wrong fbdev margins to the
front porch / back porch for both vertical and horizontal
timings.
This patch corrects it so that:
hfp = right margin
hbp = left margin
vbp = upper margin
vfp = lower margin
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
The initialization of drvdata->regs_phys was manually moved lower, to take
advantage of the NULL test on res performed by devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Just a cosmetic thing to bring that file in line with others in the
tree.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fb_set_cmap() already checks the parameters, so need remove the
redundancy checking.
This redundancy checking is also incorrect, the related warning:
drivers/video/fbcmap.c:288:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Ensure that the definitions of functions match the prototypes used by
other modules by including the header with the prototypes in the files
with the definitions.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In the old panel device model we had omap_dss_output entities,
representing the encoders in the DSS block. This entity had "device"
field, which pointed to the panel that was using the omap_dss_output.
With the new panel device model, the omap_dss_output is integrated into
omap_dss_device, which now represents a "display entity". Thus the "device"
field, now in omap_dss_device, points to the next entity in the display
entity-chain.
This patch renames the "device" field to "dst", which much better tells
what the field points to.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
In the old panel device model we had "outputs", which were the encoders
inside OMAP DSS block, and panel devices (omap_dss_device). The panel
devices had a reference to the source of the video data, i.e. reference
to an "output", in a field named "output".
That was somewhat confusing even in the old panel device model, but even
more so with the panel device model where we can have longer chains of
display entities.
This patch renames the "output" field to "src", which much better tells
what the field points to.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
With all the old panels removed and all the old panel model APIs removed
from the DSS encoders, we can now remove the custom omapdss-bus which
was used in the old panel model.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
HDMI_IDENTIFIER was felt too generic, rename it to what it is, the IEEE
OUI corresponding to HDMI Licensing, LLC.
http://standards.ieee.org/develop/regauth/oui/oui.txt
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
We just got rid of the version of hdmi_vendor_infoframe that had a byte
array for anyone to poke at. It's now time to shuffle around the naming
of hdmi_hdmi_infoframe to make hdmi_vendor_infoframe become the HDMI
vendor specific structure.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
With this last bit, hdmi_infoframe_pack() is now able to pack any
infoframe we support.
At the same time, because it's impractical to make two commits out of
this, we get rid of the version that encourages the open coding of the
vendor infoframe packing. We can do so because the only user of this API
has been ported in:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Mon Aug 12 18:08:37 2013 +0100
gpu: host1x: Port the HDMI vendor infoframe code the common helpers
v2: Change oui to be an unsigned int (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Provide the same programming model than the other infoframe types.
The generic _pack() function can't handle those yet as we need to move
the vendor OUI in the generic hdmi_vendor_infoframe structure to know
which kind of vendor infoframe we are dealing with.
v2: Fix the value of Side-by-side (half), hmdi typo, pack 3D_Ext_Data
(Ville Syrjälä)
v3: Future proof the sending of 3D_Ext_Data (Ville Syrjälä), Fix
multi-lines comment style (Thierry Reding)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Just like:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Mon Aug 12 11:53:24 2013 +0100
video/hdmi: Don't let the user of this API create invalid infoframes
But this time for the horizontal/vertical bar data present bits.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
To set the active aspect ratio value in the AVI infoframe today, you not
only have to set the active_aspect field, but also the active_info_valid
bit. Out of the 1 user of this API, we had 100% misuse, forgetting the
_valid bit. This was fixed in:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Aug 6 20:32:17 2013 +0100
drm: Don't generate invalid AVI infoframes for CEA modes
We can do better and derive the _valid bit from the user wanting to set
the active aspect ratio.
v2: Fix multi-lines comment style (Thierry Reding)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
From Christian Daudt, SoC changes for Broadcom.
* 'armsoc/for-3.12/soc' of git://github.com/broadcom/bcm11351: (673 commits)
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
+ Linux 3.11-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
The code handling 'alpha_blending_enabled' sysfs file contains WARN_ONs
in case the feature is not supported on the current platform. Even
though only root can write to the file, anyone can read it, thus causing
the kernel to get tainted and printing an ugly warning.
Instead of having WARN_ONs, return a proper error if the feature is not
supported.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Commit 5391e87d12 (OMAPDSS: remove dispc's dependency to VENC/HDMI)
introduced a possible NULL reference bug in the HDMI driver when setting
timings. In practice the bug shouldn't happen, as the timings have been
verified earlier, and thus the timings should always be ok.
Fix the possible issue by moving the use of the timings pointer inside
the NULL check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the RFBI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the VENC driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the SDI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the HDMI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the DPI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The board files now use the new panel drivers, making the old panel
drivers obsolete.
Remove the old panel drivers, Kconfig and Makefile entries, and the
panels' platform data structs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Regulator handling for DPI and SDI is currently handled in the core.c,
using the 'virtual' omapdss platform device. Nowadays we have proper
devices for both DPI and SDI, and so we can handle the regulators inside
the respective drivers.
This patch moves the regulator handling for DPI into dpi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Regulator handling for DPI and SDI is currently handled in the core.c,
using the 'virtual' omapdss platform device. Nowadays we have proper
devices for both DPI and SDI, and so we can handle the regulators inside
the respective drivers.
This patch moves the regulator handling for SDI into sdi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
OMAPDSS's RFBI encoder driver has not been working for some time. The
Nokia N800 is the only board in the mainline that uses RFBI, but it has
never been fully functional.
The RFBI driver needs to be updated to the new panel model, but as
the driver is rather unmaintained and there's no way to test the
changes, let's mark the driver as broken.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Daniel writes:
New pile of stuff for -next:
- Cleanup of the old crtc helper callbacks, all encoders are now converted
to the i915 modeset infrastructure.
- Massive amount of wm patches from Ville for ilk, snb, ivb, hsw, this is
prep work to eventually get things going for nuclear pageflips where we
need to adjust watermarks on the fly.
- More vm/vma patches from Ben. This refactoring isn't yet fully rolled
out, we miss the execbuf conversion and some of the low-level
bind/unbind support code.
- Convert our hdmi infoframe code to use the new common helper functions
(Damien). This contains some bugfixes for the common infoframe helpers.
- Some cruft removal from Damien.
- Various smaller bits&pieces all over, as usual.
* tag 'drm-intel-next-2013-08-09' of git://people.freedesktop.org/~danvet/drm-intel: (105 commits)
drm/i915: Fix FB WM for HSW
drm/i915: expose HDMI connectors on port C on BYT
drm/i915: fix a limit check in hsw_compute_wm_results()
drm/i915: unbreak i915_gem_object_ggtt_unbind()
drm/i915: Make intel_set_mode() static
drm/i915: Remove intel_modeset_disable()
drm/i915: Make intel_encoder_dpms() static
drm/i915: Make i915_hangcheck_elapsed() static
drm/i915: Fix #endif comment
drm/i915: Remove i915_gem_object_check_coherency()
drm/i915: Remove stale prototypes
drm/i915: List objects allocated from stolen memory in debugfs
drm/i915: Always call intel_update_sprite_watermarks() when disabling a plane
drm/i915: Pass plane and crtc to intel_update_sprite_watermarks
drm/i915: Don't try to disable plane if it's already disabled
drm/i915: Pass crtc to our update/disable_plane hooks
drm/i915: Split plane watermark parameters into a separate struct
drm/i915: Pull some watermarks state into a separate structure
drm/i915: Calculate max watermark levels for ILK+
drm/i915: Rename hsw_lp_wm_result to intel_wm_level
...
series involve following modifications:
1) fixing up few things in samsung_pwm_timer clocksource driver,
2) moving remaining Samsung platforms to the new clocksource driver,
3) removing old clocksource driver,
4) adding new multiplatform- and DT-aware PWM driver,
5) moving all Samsung platforms to use the new PWM driver,
6) removing old PWM driver,
7) removing all PWM-related code that is not used anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=xmmW
-----END PGP SIGNATURE-----
Merge tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux into next/cleanup
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
- convert kirkwood, dove, orion5x to DT init of mv643xx_eth
- _lots_ of board code removal :)
- convert kirkwood, dove and orion5x to DT init of clocksource and irqchip
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJR/AlqAAoJEAi3KVZQDZAeyUMH/jWUIL53x5tIcykkT4PvM5Ki
U9B2fC77XdXSjv+gHJKt4hKYC+GNGmwAbnvBSXPwE6hqUbQhn+VodR6On5AU80xS
Dk9f3BaM3uHcemn6XXjgAWn019qSLso+AwisYC4WDJLEBMjkKE5AOvkEuP63itKz
EpV7AzfDJpQ0YM+npTqN6Ea3BNxRfZ6xv7+5fr/jM3D9tuV3Ckkun6QAyak0bSme
zEPhQOqwE/+yYb7Gu8gyslf3sX+o/xhSFdkweAxULD/LR+fNvTCAC1r2DIwP5N/n
N5/vZ6u8C5reoA3ALTsbdiEOYvBiXR94g2kSaiB0u5ptONqanXtUOwYDMVB9dD8=
=Cpj7
-----END PGP SIGNATURE-----
Merge tag 'boards-3.12' of git://git.infradead.org/linux-mvebu into next/boards
From Jason Cooper:
mvebu boards changes for v3.12
- convert kirkwood, dove, orion5x to DT init of mv643xx_eth
- _lots_ of board code removal :)
- convert kirkwood, dove and orion5x to DT init of clocksource and irqchip
* tag 'boards-3.12' of git://git.infradead.org/linux-mvebu:
ARM: plat-orion: add reg offset to DT irq driver stub
ARM: kirkwood: remove obsolete SDIO clock gate workaround
ARM: kirkwood: convert to DT irqchip and clocksource
ARM: dove: convert to DT irqchip and clocksource
ARM: orion5x: update intc device tree node to new reg layout
ARM: kirkwood: move device tree nodes to DT irqchip and clocksource
ARM: dove: move device tree nodes to DT irqchip and clocksource
ARM: orion5x: remove legacy mv643xx_eth board setup
ARM: kirkwood: remove legacy clk alias for mv643xx_eth
ARM: kirkwood: remove redundant DT board files
ARM: dove: remove legacy mv643xx_eth setup
ARM: orion5x: add gigabit ethernet and mvmdio device tree nodes
ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes
ARM: dove: add gigabit ethernet and mvmdio device tree nodes
+ Linux 3.11-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bHE/
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
Updating Kconfig to allow am33xx to include lcdc fbdev driver
including some extra dependencies needed by device tree mods.
v2: must add FB_MODE_HELPERS as VIDEOMODE_HELPERS alone doesn't
get the correct functions from fbmon.c built in.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove use of explicit inline compiler directive and let the compiler
make the decision as per Documentation/CodingStyle.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the code, so that the names of the various clock variables
are consistent to it is clear what variable is associated with what
clock.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Based on original patch by: Afzal Mohammed <afzal@ti.com>
LCDC IP has a clock divider to adjust pixel clock, this limits pixel
clock range to fck/255 - fck/2(fck - rate of input clock to LCDC IP).
In the case of AM335x, where this IP is present, default fck is not
sufficient to provide normal pixel clock rates, hence rendering this
driver unusable on AM335x.
If input clock too is configurable, allowable range of pixel clock
would increase. Here initially it is checked whether with present fck,
divider in IP could be configured to obtain required rate, if not,
fck is adjusted. This makes it usable on AM335x.
Note:
Another solution would be to model an inherited basic clock divider of
CCF, an advantage would be a better possible resolution for pixel clk.
And trying to instantiate a CCF clock would mean that to be consistent,
3 bits being turned on to enable clocks of LCDC IP would have to be
modeled as gate clocks. Now that would bring in a total of 4 clocks,
including necessity to create a new inherited divider clock, and that
mean a branch of clock tree would be present in LCDC driver. This
would add complexity to LCDC driver bringing in considerable amount
of clock handling code, and this would not bring in much advantage
for existing use cases other than providing a higher resolution of
pixel clock. And existing use cases work without relying on clock
modeling. Another fact is that out of the two platform's using this
driver DaVinci is not yet converted to CCF. In future if higher
resolution of pixel clock is required, and probably after DaVinci is
CCF'ed, modeling clock nodes inside driver may be considered.
v2: purely cosmetic changes to try and clarify what variables are
being used for in the clock rate / divider calculations
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move panel detection to a separate function, this helps in readability
as well as makes DT support cleaner.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Ensure that platform data contains pointer for lcd_ctrl_config.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace existing resource handling in the driver with managed device
resource.
v2: implement some changes as recommended by
Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The interrupt handler explicitly has code that handles the sync lost
interrupt. However the sync lost interrupt is never actually being
enabled in the LCD controller, therefore this interrupt code path is not
being exercised. This fix simply enables the generation of the sync
lost interrupt by the LCD controller so it can be dealt with
appropriately by the interrupt handler.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Based on original patch by: Manjunathappa, Prakash <prakash.pm@ti.com>
and Afzal Mohammed <afzal@ti.com>
Set only LCD_V2_TFT_24BPP_MODE bit for 24bpp and LCD_V2_TFT_24BPP_UNPACK
bit along with LCD_V2_TFT_24BPP_MODE for 32bpp configuration.
Patch is tested on am335x-evm for 24bpp and da850-evm for 16bpp
configurations.
v2: removes confusing fall through in case statement for pixel
depth configuration.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the lcd_disable_raster funtion from using a bool to an enum
as the function is very confusing with the current api. This helps
make it clearer what the parameter is really doing.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
v1: original from Afzal Mohammed <afzal@ti.com>
fb_set_par helps in runtime configuration of lcd controller like
changing resolution, pixel clock etc. (eg. using fbset utility)
Reconfigure lcd controller based on information passed by framework.
Enable raster back if it was already enabled.
As fb_set_par would get invoked indirectly from probe via fb_set_var,
remove existing lcdc initialization in probe and do lcdc reset in
probe so that reset happens only at the begining.
v2: changes from Darren Etheridge <detheridge@ti.com>
remove unnecessary conditional branch where we attempt to disable
something that we already checked to see if it was disabled.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Update "var" pixclock with the value that is configurable in hardware.
This lets user know the actual pixclock.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
store struct device pointer so that dev_dbg/err can be used outside
of probe.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Based on original patch by: Afzal Mohammed <afzal@ti.com>
Use the new modedb field to store pix clk. Reorganize existing clock
divider functions with names now corresponding to what they do, add
common function prefix.
Fix existing panel modedb pixclock to be in ps instead of Hz. This
needed a change in the way clock divider is calculated. As modedb
pixclock information is now in ps, override on "var" pixclock over
modedb to var conversion is removed.
v2:
Changed pixel clock configuration to use KHZ2PICOS macro
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
store lcd clk rate always, i.e. irrespective of whether CPUFREQ is
enabled or not. This can be used to get clk rate directly instead of
enquiring with clock framework with clk handle every time.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
store current videomode and controller data so that reconfiguring can
be done easily. Reconfiguring would be required in fb_set_par, which
is going to be added soon.
If these details are not stored, the work probe does to retrieve these
information would have to repeated at the place of reconfiguring and
modifying platform data would be necessary to handle controller data
changes like bpp.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
modedb helper now updates "var" information based on the detected
panel, remove the unnecessary initialization.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
modedb structure is now used to store panel information, run modedb
helper over it for initial update of "var" information instead of
equating each fields.
While at it, remove redundant update of bits_per_pixel.
Note: pixclock is overridden with proper value using an existing code
as currently modedb is having it in Hz instead of ps, this would be
fixed in a later change and this overide would be removed.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
lcd_reset function doesn't require any arguement, remove it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Check whether "struct fb_var_screeninfo" fields are sane, if not
update it to be within allowed limits.
If user sends down buggy "var" values, this will bring those within
allowable limits. And fb_set_par is not supposed to change "var"
values, fb_check_var has to ensure that values are proper.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the user if this API is providing a bigger buffer than the infoframe
size, it could be for a could reason. For instance it could be because
it gives the buffer that will be written to the hardware, up to the
maximum of an infoframe size.
Instead of just zeroing up to the infoframe size, let's zero the whole
incoming buffer as those extra bytes are also used to compute the
ECC and need to be 0.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And a way to pack hdmi_infoframe generically.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The contents of mach/board.h are only used by files within
mach-msm so there is no need to export this file outside of the
mach-msm directory. Move the contents of the file to common.h to
allow us to compile MSM in the multi-platform kernel.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
ti_hdmi_4xxx_basic_configure() is supposed to initialize the AVI
infoframe data in the ip_data container. However, the function actually
takes a copy of the infoframe from the ip_data, and then goes on
initializing that copy. The initialized data is never copied back to the
ip_data container, thus the infoframe in ip_data is left always zero.
Afaik, this doesn't really cause any issues in the current mainline, as
we don't use the advanced features offered by the AVI infoframe.
This patch fixes the initialization of the AVI infoframe.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fbdev provides framebuffer hotplugging, hence, we need to allow fbcon to
unbind from framebuffers. Unfortunately, fbcon_fb_unbind() cannot unbind
from the last framebuffer, unless console-unbinding is supported.
Fixing fbcon_unbind() to return 0 caused some horrible NULL-derefs in the
VT layer and I couldn't figure out why. Hence, lets just require
console-unbinding so fbdev hotplugging works with fbcon.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-9-git-send-email-dh.herrmann@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
x86 creates platform-framebuffer platform devices for every system
framebuffer. Use these instead of creating a dummy device.
This requires us to remove the __init annotations as hotplugging may occur
during runtime.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-7-git-send-email-dh.herrmann@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The EFI FB quirks from efifb.c are useful for simple-framebuffer devices
as well. Apply them by default so we can convert efifb.c to use
efi-framebuffer platform devices.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-5-git-send-email-dh.herrmann@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
fbdev-core uses FBINFO_MISC_FIRMWARE to mark drivers that use firmware
framebuffers. Furthermore, we now allocate apertures for the fbinfo
device.
Both information is used by remove_conflicting_framebuffers() to remove a
fbdev device whenever a real driver is loaded. This is used heavily on x86
for VGA/vesa/EFI framebuffers, but is also of great use for all other
systems.
Especially with x86 support for simplefb, this information is needed to
unload simplefb before a real hw-driver (like i915, radeon, nouveau) is
loaded.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-3-git-send-email-dh.herrmann@gmail.com
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we create proper platform-devices in x86 boot-code, we can use simplefb
for VBE or EFI framebuffers, too. However, there is normally no OF support
so we introduce a platform_data object so x86 boot-code can pass the
parameters via plain old platform-data.
This also removes the OF dependency as it is not needed. The headers
provide proper dummies for the case OF is disabled.
Furthermore, we move the FORMAT-definitions to the common platform header
so initialization code can use it to transform "struct screen_info" to
the right format-name.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-2-git-send-email-dh.herrmann@gmail.com
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add support for the Himax HX8369 controller as it is quite similar to the
hx8357.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The IM pins of the HX8357 controller are used to define the interface
used to feed pixel stream to the LCD panel.
Most of the time, these pins are directly routed to either the ground or
the VCC to set their values.
Remove the need to assign GPIOs to these pins when we are in such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For a combination of 18bit LCD data bus width and a color
mode of 32bpp, the driver was setting the color mapping to
rgb666, which is wrong, as the color in memory realy has an
rgb888 layout.
This patch also removes the setting of flag CTRL_DF24 that
makes the driver dimiss the upper 2 bits when handling 32/24bpp
colors in a diplay with 18bit data bus width. This flag made
true color images display wrong in such configurations.
Finally, the color mapping rgb666 has also been removed as nobody
is using it and high level applications like Qt5 cannot work
with it either.
Reference: https://lkml.org/lkml/2013/5/23/220
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Juergen Beisert <jbe@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
connector-analog-tv.c uses omap_dss_pal_timings, defined in omapdss's
venc.c, for default timings. omap_dss_pal_timings only exists when VENC
is enabled in the kernel config, so disabling VENC breaks
omap_dss_pal_timings connector-analog-tv compilation.
Instead of adding dependency to VENC, add internal default timings to
the connector driver, because the connector driver should not depend on
VENC, and it can be used with any other analog TV encoder.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove HV_DRV_VERSION, it has no meaning for upstream drivers.
Initially it was supposed to show the "Linux Integration Services"
version, now it is not in sync anymore with the out-of-tree drivers
available from the MSFT website.
The only place where a version string is still required is the KVP
command "IntegrationServicesVersion" which is handled by
tools/hv/hv_kvp_daemon.c. To satisfy such KVP request from the host pass
the current string to the daemon during KVP userland registration.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 6e36308a6f "fb: fix atyfb build warning" isn't right. It makes all
the indexes off by one. This patch reverts it and casts the
ARRAY_SIZE() to int to silence the build warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A framebuffer of this format is set up by SHIELD's bootloader.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When backlight turns on early from display, a white line can be
seen on the screen. Therefore make sure backlight is off when we
are under an fb blank event.
Signed-off-by: Shingo Nakao <shingo.x.nakao@sonymobile.com>
Cc: Milo Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch proposes to remove the FB_NUC900_DEBUG kernel configuration
parameter defined in drivers/video/Kconfig, but used nowhere
in the makefiles and source code.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit c84deb9d61 ("fbdev/sgivwfb: use
vm_iomap_memory()") changed sgivwfb_mmap() to use the new
vm_iomap_memory() function. The commit introduced the following
compilation error:
drivers/video/sgivwfb.c:716:9: note: each undeclared identifier is
reported only once for each function it appears in
This patch fixes the error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The IRQ handler nuc900fb_irqhandler() use dev_id as a type of
struct nuc900fb_info *, so we should pass fbi as the device
identity to request_irq().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the video output class code to
use the correct field.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regs_phys is phys_addr_t (u32 or u64).
Lets use %pa printk format specifier.
Fixes compilation warning introduced by:
video: xilinxfb: Use drvdata->regs_phys instead of physaddr
(sha1: c88fafef01)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The device-tree enablement for max8925 has several problems, but besides
the bindings being wrong (and not having seen review) there's also some
bad coding practices on how to fill in the platform_data from device tree.
I came across this since it causes a warning when compiling
mmp2_defconfig, and instead of doing the minimal fix to silence the
warning, I restructured the code a bit.
This silences the warning:
drivers/video/backlight/max8925_bl.c: In function 'max8925_backlight_probe':
drivers/video/backlight/max8925_bl.c:177:3: warning: statement with no effect [-Wunused-value]
Note that the bindings themselves need to be revisited too, but that will
affect more than just the backlight driver and is best done separately;
this just fixes the bad code for the backlight driver.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the video backlight lcd class
code to use the correct field.
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the video backlight class code to
use the correct field.
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BD6107 is a multi-purpose 10 channels LED driver for the mobile
market. Only the main channel is supported by this driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LV5207LP is a multi-purpose 7 LEDs driver for the mobile market.
Only the main LED is supported by this driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The GPIO backlight driver controls the backlight in on/off mode through
a single GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Convert drivers/video/backlight/class to use dev_pm_ops for power
management and remove Legacy PM ops hooks.
With this change, backlight class registers suspend/resume callbacks via
class->pm (dev_pm_ops) instead of Legacy class->suspend/resume. When
__device_suspend() runs call-backs, it will find class->pm ops for the
backlight class.
[jg1.han@samsung.com: add CONFIG_PM_SLEEP to suspend/resume functions]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These functions allow the driver core to automatically clean up any
allocation made by lcd drivers. Thus it simplifies the error paths.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These functions allow the driver core to automatically clean up any
allocation made by backlight drivers. Thus it simplifies the error
paths.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or
on probe failure, since commit 0998d06310 ("device-core: Ensure drvdata
= NULL when no driver is bound").
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or
on probe failure, since commit 0998d06310 ("device-core: Ensure drvdata
= NULL when no driver is bound").
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or
on probe failure, since commit 0998d06310 ("device-core: Ensure drvdata
= NULL when no driver is bound").
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or
on probe failure, since commit 0998d06310 ("device-core: Ensure drvdata
= NULL when no driver is bound").
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calling dev_set_name with a single paramter causes it to be handled as a
format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull "exotic" arch fixes from Geert Uytterhoeven:
"This is a collection of several exotic architecture fixes, and a few
other fixes for issues that were detected while doing the former"
* 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (35 commits)
lib: Move fonts from drivers/video/console/ to lib/fonts/
console/font: Refactor font support code selection logic
Revert "staging/solo6x10: depend on CONFIG_FONTS"
input: cros_ec_keyb_clear_keyboard() depends on CONFIG_PM_SLEEP
score: Wire up asm-generic/xor.h
score: Remove unneeded <asm/dma-mapping.h>
openrisc: Wire up asm-generic/xor.h
h8300/boot: Use POSIX "$((..))" instead of bashism "$[...]"
h8300: Mark H83002 and H83048 CPU support broken
h8300: Switch h8300 to drivers/Kconfig
h8300: Limit timer channel ranges in Kconfig
h8300: Wire up asm-generic/xor.h
h8300: Fill the system call table using a CALL() macro
h8300: Fix <asm/tlb.h>
h8300: Hardcode symbol prefixes in asm sources
h8300: add missing definition for read_barries_depends()
frv: head.S - Remove commented-out initialization code
cris: Wire up asm-generic/vga.h
parport: disable PC-style parallel port support on cris
console: Disable VGA text console support on cris
...
Pull workqueue changes from Tejun Heo:
"Surprisingly, Lai and I didn't break too many things implementing
custom pools and stuff last time around and there aren't any follow-up
changes necessary at this point.
The only change in this pull request is Viresh's patches to make some
per-cpu workqueues to behave as unbound workqueues dependent on a boot
param whose default can be configured via a config option. This leads
to higher processing overhead / lower bandwidth as more work items are
bounced across CPUs; however, it can lead to noticeable powersave in
certain configurations - ~10% w/ idlish constant workload on a
big.LITTLE configuration according to Viresh.
This is because per-cpu workqueues interfere with how the scheduler
perceives whether or not each CPU is idle by forcing pinned tasks on
them, which makes the scheduler's power-aware scheduling decisions
less effective.
Its effectiveness is likely less pronounced on homogenous
configurations and this type of optimization can probably be made
automatic; however, the changes are pretty minimal and the affected
workqueues are clearly marked, so it's an easy gain for some
configurations for the time being with pretty unintrusive changes."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
fbcon: queue work on power efficient wq
block: queue work on power efficient wq
PHYLIB: queue work on system_power_efficient_wq
workqueue: Add system wide power_efficient workqueues
workqueues: Introduce new flag WQ_POWER_EFFICIENT for power oriented workqueues
Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just removed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRsGMACgkQMUfUDdst+ylIIACfW8lLxOPVK+iYG699TWEBAkp0
LFEAnjlpAMJ1JnoZCuWDZObNCev93zGB
=020+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just
removed)"
* tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
driver core: device.h: fix doc compilation warnings
firmware loader: fix another compile warning with PM_SLEEP unset
build some drivers only when compile-testing
firmware loader: fix compile warning with PM_SLEEP set
kobject: sanitize argument for format string
sysfs_notify is only possible on file attributes
firmware loader: simplify holding module for request_firmware
firmware loader: don't export cache_firmware and uncache_firmware
drivers/base: Use attribute groups to create sysfs memory files
firmware loader: fix compile warning
firmware loader: fix build failure with !CONFIG_FW_LOADER_USER_HELPER
Documentation: Updated broken link in HOWTO
Finally eradicate CONFIG_HOTPLUG
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests before suspend
driver core: firmware loader: don't cache FW_ACTION_NOHOTPLUG firmware
Documentation: Tidy up some drivers/base/core.c kerneldoc content.
platform_device: use a macro instead of platform_driver_register
firmware: move EXPORT_SYMBOL annotations
firmware: Avoid deadlock of usermodehelper lock at shutdown
dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly
...
Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is a
nice change, just a number of serial driver fixes and updates and new
drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with the
exception of the last revert patch, which was reported this past weekend
by two different people as being needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRtNIACgkQMUfUDdst+ymYgwCeKdyv9wRJ5cIWZt7Jz8ou3P/C
76YAoIvMv+fwoFBpyud/sC8eAKGTQ6KB
=Sjk6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is
a nice change, just a number of serial driver fixes and updates and
new drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with
the exception of the last revert patch, which was reported this past
weekend by two different people as being needed."
* tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (51 commits)
Revert "serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller"
pch_uart: Add uart_clk selection for the MinnowBoard
tty: atmel_serial: prepare clk before calling enable
tty: Reset itty for other pty
n_tty: Buffer work should not reschedule itself
n_tty: Fix unsafe update of available buffer space
n_tty: Untangle read completion variables
n_tty: Encapsulate minimum_to_wake within N_TTY
serial: omap: Fix device tree based PM runtime
serial: imx: Fix serial clock unbalance
serial/mpc52xx_uart: fix kernel panic when system reboot
serial: mfd: Add sysrq support
serial: imx: enable the clocks for console
tty: serial: add Freescale lpuart driver support
serial: imx: Improve Kconfig text
serial: imx: Allow module build
serial: imx: Fix warning when !CONFIG_SERIAL_IMX_CONSOLE
tty/serial/sirf: fix error propagation in sirfsoc_uart_probe()
serial: omap: fix potential NULL pointer dereference in serial_omap_runtime_suspend()
tty: serial: Enable uartlite for ARM zynq
...
This is the second part of OMAP DSS changes for 3.11. This part contains the
new DSS device model support.
The current OMAP panel drivers use a custom DSS bus, and there's a hard limit
of one external display block per video pipeline. In the new DSS device model
the devices/drivers are made according to the control bus of the display block,
usually platform, i2c or spi. The display blocks can also be chained so that we
can have separate drivers for setups with both external encoder and panel.
To allow the current board files, which use the old style panels, to function,
the old display drivers are left in their current state, and new ones are added
to drivers/video/omap2/displays-new/. When the board files have been converted
to use the new style panels, we can remove the old code. This is planned to
happen in v3.12.
Having to support two very different DSS device models makes the driver
somewhat confusing in some parts, and prevents us from properly cleaning up
some other parts. These cleanups will be done when the old code is removed.
The new device model is designed with CDF (Common Display Framework) in mind.
While CDF is still under work, the new DSS device model should be much more
similar to CDF's model than the old device model, which should make the
eventual conversion to CDF much easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yEcM
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.11-2' of git://gitorious.org/linux-omap-dss2/linux into fbdev/for-next
OMAP display subsystem changes for 3.11 (part 2/2)
This is the second part of OMAP DSS changes for 3.11. This part contains the
new DSS device model support.
The current OMAP panel drivers use a custom DSS bus, and there's a hard limit
of one external display block per video pipeline. In the new DSS device model
the devices/drivers are made according to the control bus of the display block,
usually platform, i2c or spi. The display blocks can also be chained so that we
can have separate drivers for setups with both external encoder and panel.
To allow the current board files, which use the old style panels, to function,
the old display drivers are left in their current state, and new ones are added
to drivers/video/omap2/displays-new/. When the board files have been converted
to use the new style panels, we can remove the old code. This is planned to
happen in v3.12.
Having to support two very different DSS device models makes the driver
somewhat confusing in some parts, and prevents us from properly cleaning up
some other parts. These cleanups will be done when the old code is removed.
The new device model is designed with CDF (Common Display Framework) in mind.
While CDF is still under work, the new DSS device model should be much more
similar to CDF's model than the old device model, which should make the
eventual conversion to CDF much easier.
This is the first part of OMAP DSS changes for 3.11. This part contains fixes,
cleanups and reorganizations that are not directly related to the new DSS
device model that is added in part 2, although many of the reorganizations are
made to make the part 2 possible.
There should not be any functional changes visible to the user except the few
bug fixes.
The main new internal features:
- Display (dis)connect support, which allows us to explicitly (dis)connect a
whole display pipeline
- Panel list, which allows us to operate without the specific DSS bus
- Combine omap_dss_output to omap_dss_device, so that we have one generic
"entity" for display pipeline blocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=I6Y2
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.11-1' of git://gitorious.org/linux-omap-dss2/linux into fbdev/for-next
OMAP display subsystem changes for 3.11 (part 1/2)
This is the first part of OMAP DSS changes for 3.11. This part contains fixes,
cleanups and reorganizations that are not directly related to the new DSS
device model that is added in part 2, although many of the reorganizations are
made to make the part 2 possible.
There should not be any functional changes visible to the user except the few
bug fixes.
The main new internal features:
- Display (dis)connect support, which allows us to explicitly (dis)connect a
whole display pipeline
- Panel list, which allows us to operate without the specific DSS bus
- Combine omap_dss_output to omap_dss_device, so that we have one generic
"entity" for display pipeline blocks
Several drivers need font support independent of CONFIG_VT, cfr. commit
9cbce8d7e1dae0744ca4f68d62aa7de18196b6f4, "console/font: Refactor font
support code selection logic").
Hence move the fonts and their support logic from drivers/video/console/ to
its own library directory lib/fonts/.
This also allows to limit processing of drivers/video/console/Makefile to
CONFIG_VT=y again.
[Kevin Hilman <khilman@linaro.org>: Update arch/arm/boot/compressed/Makefile]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEbBAABAgAGBQJRxf9cAAoJEHm+PkMAQRiGMWkH911xM4gRmFgE7SqVW4F4AWBm
ngcqMqNy9IdqKfibORUUDvVfEa5gjD5ai2quIKpfQiaukbpQJ696H90ijuAkajLn
DQBrN243s0pzhhc/quWINnWxsFQ613JjdUMUMaD7e9A1aKjYzWrPGt/tSjrFXGCP
tArTupVzc/iOmnEQDKiROI/Nokq44QJ36aTGPM7n08xMtpKmkCXM+9/UosBteB0O
HVI33dmjwz7i55fI53XAWyuZCE+gSEnA4z8spJ9LfXso2W14V+roc+GuL6OyeeTI
pCn/+4niVPb4B0ROZlpyVmdZjbPPcMMEK5o+BSJI68SH6LHZTQh2iVuqYfpSyA==
=uUH5
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc7' into drm-next
Linux 3.10-rc7
The sdvo lvds fix in this -fixes pull
commit c3456fb3e4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jun 10 09:47:58 2013 +0200
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
has a silent functional conflict with
commit 990256aec2
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri May 31 12:17:07 2013 +0000
drm: Add probed modes in probe order
in drm-next. W simply need to add the vbt modes before edid modes, i.e. the
other way round than now.
Conflicts:
drivers/gpu/drm/drm_prime.c
drivers/gpu/drm/i915/intel_sdvo.c
i740fb_init is referenced only in this function. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
drm_get_connector_name now returns a const value, which causes the following
compilation warning:
drivers/gpu/drm/drm_fb_helper.c: In function ‘drm_fb_helper_parse_command_line’:
drivers/gpu/drm/drm_fb_helper.c:127:3: warning: passing argument 1 of ‘fb_get_options’ discards ‘const’ qualifier from pointer target type [enabled by default]
In file included from drivers/gpu/drm/drm_fb_helper.c:35:0:
include/linux/fb.h:627:12: note: expected ‘char *’ but argument is of type ‘const char *’
As fb_get_options uses its name argument as read only, make it const. This
fixes the aforementioned compilation warning.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: trivial@kernel.org
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
There is bug when switch dma of graphic layer and video layer, it
configured opposite bit, fix it.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use dev_pm_ops instead of the legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
copy_to_user() returns the number of bytes remaining to be copied.
put_user() returns -EFAULT on error.
This function ORs a bunch of stuff together and returns jumbled non-zero
values on error. It should return -EFAULT.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI is supposed to skip odd dividers in the clock path when the pixel
clock is higher than 100MHz. The code, however, defines the pixel clock
limit as 1MHz. This causes the driver to skip valid clock dividers,
possibly making the pixel clock to be further away from the requested
one than necessary.
Fix the clock limit to 100MHz.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: NeilBrown <neilb@suse.de>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Streamline it a bit. No functional change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Wang YanQing <udknight@gmail.com>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Acked-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix compiler warnings of data defined but not used by using the
__maybe_unused attribute. The date are only used with certain kconfig
settings.
drivers/video/aty/atyfb_base.c:534:13: warning: 'ram_dram' defined but not used [-Wunused-variable]
drivers/video/aty/atyfb_base.c:535:13: warning: 'ram_resv' defined but not used [-Wunused-variable]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-fbdev@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix build warning when neither of CONFIG_FB_ATY_GX or
CONFIG_FB_ATY_CT is enabled, since ARRAY_SIZE(aty_chips) is 0 in
that case.
drivers/video/aty/atyfb_base.c:437:11: warning: overflow in implicit constant conversion [-Woverflow]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-fbdev@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These symbols are used only in this file.
Make them static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
'dlfb_handle_damage' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pointer variables should be initialized with NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
'info' is a pointer. Use NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enable this driver for all Xilinx platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dynamically detect endianess on IP and use
ioread/iowrite functions instead of powerpc and microblaze
specific out_be32.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move of_address_to_resource() to xilinxfb_assign()
which simplify driver probing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
physaddr will be remove in the next patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Using only PLB name is wrong for a long time because
the same access functions are also used for AXI.
s/PLB/BUS/g
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
out_be32 IO function is not supported by ARM.
It is only available for PPC and Microblaze.
Because this driver can be used on ARM let's
remove out_be32 from function name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DTB is always big-endian that's why it is necessary
to properly convert value (*p).
It is automatically done in of_property_read_u32().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Booting a 64-vcpu KVM guest, with CONFIG_PREEMPT_VOLUNTARY,
can result in a soft lockup:
BUG: soft lockup - CPU#41 stuck for 67s! [setfont:1505]
RIP: 0010:[<ffffffff812c48da>]
[<ffffffff812c48da>] vgacon_do_font_op.clone.0+0x1ba/0x550
This is due to the 8192 (cmapsz) IO operations taking longer than expected
due to lock contention in QEMU.
Add conditional resched points in between writes allowing other tasks to
execute.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some drivers can be built on more platforms than they run on. This is
a burden for users and distributors who package a kernel. They have to
manually deselect some (for them useless) drivers when updating their
configs via oldconfig. And yet, sometimes it is even impossible to
disable the drivers without patching the kernel.
Introduce a new config option COMPILE_TEST and make all those drivers
to depend on the platform they run on, or on the COMPILE_TEST option.
Now, when users/distributors choose COMPILE_TEST=n they will not have
the drivers in their allmodconfig setups, but developers still can
compile-test them with COMPILE_TEST=y.
Now the drivers where we use this new option:
* PTP_1588_CLOCK_PCH: The PCH EG20T is only compatible with Intel Atom
processors so it should depend on x86.
* FB_GEODE: Geode is 32-bit only so only enable it for X86_32.
* USB_CHIPIDEA_IMX: The OF_DEVICE dependency will be met on powerpc
systems -- which do not actually support the hardware via that
method.
* INTEL_MID_PTI: It is specific to the Penwell type of Intel Atom
device.
[v2]
* remove EXPERT dependency
[gregkh - remove chipidea portion, as it's incorrect, and also doesn't
apply to my driver-core tree]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-geode@lists.infradead.org
Cc: linux-fbdev@vger.kernel.org
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: "Keller, Jacob E" <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current Makefile rules to build font support are messy and buggy.
Replace them by Kconfig rules:
- Introduce CONFIG_FONT_SUPPORT, which controls the building of all font
code,
- Select CONFIG_FONT_SUPPORT for all drivers that use fonts,
- Select CONFIG_FONT_8x16 for all drivers that default to the VGA8x16
font,
- Drop the bogus console dependency for CONFIG_VIDEO_VIVI,
- Always process drivers/video/console/Makefile, as some drivers need
fonts even if CONFIG_VT is not set.
This fixes (if CONFIG_SOLO6X10=y and there are no built-in console
drivers):
drivers/built-in.o: In function `solo_osd_print':
drivers/staging/media/solo6x10/solo6x10-enc.c:144: undefined reference to `.find_font'
This fixes (if CONFIG_VT=n):
drivers/built-in.o: In function `vivi_init':
vivi.c:(.init.text+0x1a3da): undefined reference to `find_font'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> [original part]
Acked-by: Randy Dunlap <rdunlap@infradead.org> [drivers/video/Makefile]
This reverts commit 8c090cfbf9.
CONFIG_FONTS is not about enabling font support, but about enabling
manual selection of built-in fonts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add TPO TD043MTEA1 panel driver which uses the new DSS device model
and DSS ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Add Sony ACX565AKM panel driver which uses the new DSS device model and
DSS ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Add DSI Command Mode panel driver which uses the new DSS device model
and DSS ops. This driver only supports a very basic set of features
which should be common to all DSI command mode panels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add simple DPI Panel driver which uses the new DSS device model and DSS
ops. A "simple" panel means one that does not require any special setup.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add TPD12S015 HDMI ESD protection and level shifter encoder driver which
uses the new DSS device model and DSS ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using DSI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using HDMI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using analog TV functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using SDI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using DPI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new display bus type for DVI. This is not used by omapdss driver
itself, but is used by external encoder chips that output DVI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In the future will have arbitrarily long video pipeline chains, instead
of the current two-entities-per-pipeline model.
This patch changes the affected get/find style functions so that they
properly go through the video pipeline chain, for example when getting
the overlay manager connected to a given display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to allow multiple display block in a video pipeline, we need to
give the drivers way to register themselves. For now we have
the omapdss_register_display() which is used to register panels, and
dss_register_output() which is used to register DSS encoders.
This patch makes dss_register_output() public (with the name of
omapdss_register_output), which can be used to register also external
encoders. The distinction between register_output and register_display
is that a "display" is an entity at the end of the videopipeline, and
"output" is something inside the pipeline.
The registration and naming will be made saner in the future, but the
current names and functions are kept to minimize changes during the dss
device model transition.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Disable overlay via ovl->disable() interface, which will
properly set flags in cache and GO bits for managers.
This allows overlay user to re-enable it on next frame,
thus recovering from FIFO underflows.
Signed-off-by: Sergey Kibrik <sergiikibrik@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It's not necessary to free memory allocated with devm_kzalloc
in a remove function and using kfree leads to a double free.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC needs to know the clock rate for DIGIT (i.e. TV) channel, and this
clock is provided by either VENC or HDMI modules. Currently DISPC will
call a function in VENC/HDMI, asking what the clock rate is. This means
we have a fixed dependency from DISPC to both VENC and HDMI.
To have a more generic approach, and in particular to allow adding OMAP5
HDMI driver, we need to remove this dependency. This patch makes
VENC/HDMI inform DISPC when the their clock changes, thus reversing the
dependency and removing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hpd_gpio is no longer used by the OMAP4 HDMI IP driver, and we can thus
remove the unnecessary code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TRM tells to set PHY to TXON only after getting LINK_CONNECT, and to
set PHY to OFF or LDOON after getting LINK_DISCONNECT, in order to avoid
damage to the PHY.
We don't currently do it quite like that. Instead of using the HDMI
interrupts, we use HPD signal. This works, but is not actually quite
correct, as HPD comes at a different time than LINK_CONNECT and
LINK_DISCONNECT interrupts. Also, the HPD GPIO is a property of the TPD
level shifter, not HDMI IP, so handling the GPIO in the HDMI driver is
wrong.
This patch implements the PHY power handling correctly, using the
interrupts.
There is a corner case that causes some additional difficulties: we may
get both LINK_CONNECT and LINK_DISCONNECT interrupts at the same time.
This is handled in the code by retrying: turning off the PHY, clearing
the interrupt status, and re-enabling the PHY. This causes a new
LINK_CONNECT interrupt to happen if a cable is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb returns EPROBE_DEFER if no displays have been probed at
the time omapfb is probed. However, sometimes some of the displays have
been probed at that time, but not all. We can't return EPROBE_DEFER in
that case, because then one missing driver would cause omapfb to defer
always, preventing any display from working.
However, if the user has defined a default display, we can presume that
the driver for that display is eventually loaded. Thus, this patch
changes omapfb to return EPROBE_DEFER in case default display is not
found.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that omap_dss_output has been combined into omap_dss_device, we can
add ref counting for the relevant output functions also.
This patch adds omap_dss_get_device() calls to the various find_output()
style functions. This, of course, means that the users of those
find_output functions need to do a omap_dss_put_device() after use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_get_device() should be called for omap_dss_device before it is
used to increase its refcount. Currently we only increase the refcount
for the underlying device.
This patch adds managing the ref count to the underlying module also,
which contains the ops for the omap_dss_device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have omap_dss_device, which represents an external display
device, sometimes an external encoder, sometimes a panel. Then we have
omap_dss_output, which represents DSS's output encoder.
In the future with new display device model, we construct a video
pipeline from the display blocks. To accomplish this, all the blocks
need to be presented by the same entity.
Thus, this patch combines omap_dss_output into omap_dss_device. Some of
the fields in omap_dss_output are already found in omap_dss_device, but
some are not. This means we'll have DSS output specific fields in
omap_dss_device, which is not very nice. However, it is easier to just
keep those output specific fields there for now, and after transition to
new display device model is made, they can be cleaned up easier than
could be done now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_start_device() and omap_dss_stop_device(), called by the
DSS output drivers, are old relics. They originally did something
totally else, but nowadays they increase the module ref count for panels
that are enabled.
This model is quite broken: the panel modules may be used even before
they are enabled. For example, configuring the panel requires calls to
functions located in the panel modules.
In the following patches we try to improve the ref count management for
the modules and display devices. The first step, however, is to remove
the omap_dss_start/stop_device() totally.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
