A clock specifier is required for i.MX I2C and is
provided in all DTS implementations. Add this to the
list of required properties in the binding.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.
The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the big staging driver tree update for 3.20-rc1. Lots of little
things in here, adding up to lots of overall cleanups. The IIO driver
updates are also in here as they cross the staging tree boundry a lot.
I2O has moved into staging as well, as a plan to drop it from the tree
eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtVQACgkQMUfUDdst+yk4mACgshYZ1fOQDoPR+BXd+QD1HXfh
GosAoICXkSjDQjwVo13W6QHIVMsUezY+
=4jHr
-----END PGP SIGNATURE-----
Merge tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging drivers patches from Greg KH:
"Here's the big staging driver tree update for 3.20-rc1.
Lots of little things in here, adding up to lots of overall cleanups.
The IIO driver updates are also in here as they cross the staging tree
boundry a lot. I2O has moved into staging as well, as a plan to drop
it from the tree eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a
while"
* tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (740 commits)
staging: lustre: lustre: libcfs: define symbols as static
staging: rtl8712: Do coding style cleanup
staging: lustre: make obd_updatemax_lock static
staging: rtl8188eu: core: switch with redundant cases
staging: rtl8188eu: odm: conditional setting with no effect
staging: rtl8188eu: odm: condition with no effect
staging: ft1000: fix braces warning
staging: sm7xxfb: fix remaining CamelCase
staging: sm7xxfb: fix CamelCase
staging: rtl8723au: multiple condition with no effect - if identical to else
staging: sm7xxfb: make smtc_scr_info static
staging/lustre/mdc: Initialize req in mdc_enqueue for !it case
staging/lustre/clio: Do not allow group locks with gid 0
staging/lustre/llite: don't add to page cache upon failure
staging/lustre/llite: Add exception entry check after radix_tree
staging/lustre/libcfs: protect kkuc_groups from write access
staging/lustre/fld: refer to MDT0 for fld lookup in some cases
staging/lustre/llite: Solve a race to access lli_has_smd in read case
staging/lustre/ptlrpc: hold rq_lock when modify rq_flags
staging/lustre/lnet: portal spreading rotor should be unsigned
...
This patch adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3
RTC/Calendar module w/ I2C interface.
This support includes RTC time reading and setting, Alarm (1 minute
accuracy) reading and setting, and battery low detection. The device also
supports frequency adjustment and two timers but those features are
currently not implemented in this driver. Due to alarm accuracy
limitation (and current lack of timer support in the driver), UIE mode is
not supported.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- DT unittests for I2C probing and overlays from Pantelis Antoniou
- Remove DT unittest dependency on OF_DYNAMIC from Gaurav Minocha
- Add Tegra compatible strings missing for newer parts from Paul
Walmsley
- Various vendor prefix additions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU3CJVAAoJEMhvYp4jgsXieMgIAKlpr8gcMq/ORRRbVJ9jrL64
A0gPZZEBBVJ0BX7b6mvz15/6Zt70naoE23tMgaCQpR620ox9xFshmwhzHct9npiQ
KRode+9QhFRvA3Pc5LXhfD+bnyJ3Z4pWPrbY6sDDL9txqolpUhU4fz8Y3InwN5YB
GSD6NG3UKDmrTOvkR1j2WrCIkSeXYAEKtnuQlN/+eZXM6kzZYDcdskHv6o18mf4b
Ys6mwkfJdN3UZVQE8ZxUSi3wdC9U7mErNOZuc2rgL9Qb+q0RHtgE2GTI2Zxw0Sj1
BlCO1Fs0sYhOunZIazLJht7cenGbBMf+ed2DB4VLNiEmPhavqdv9wjNt9jOjh5k=
=Aviy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree changes from Rob Herring:
- DT unittests for I2C probing and overlays from Pantelis Antoniou
- Remove DT unittest dependency on OF_DYNAMIC from Gaurav Minocha
- Add Tegra compatible strings missing for newer parts from Paul
Walmsley
- Various vendor prefix additions
* tag 'devicetree-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Add vendor prefix for OmniVision Technologies
of: Use ovti for Omnivision
of: Add vendor prefix for Truly Semiconductors Limited
of: Add vendor prefix for Himax Technologies Inc.
of/fdt: fix sparse warning
of: unitest: Add I2C overlay unit tests.
Documentation: DT: document compatible string existence requirement
Documentation: DT bindings: add nvidia, tegra132-denver compatible string
Documentation: DT bindings: add more Tegra chip compatible strings
of: EXPORT_SYMBOL_GPL of_property_read_u64_array
of: Fix brace position for struct of_device_id definition
of/unittest: Remove obsolete code
dt-bindings: use isil prefix for Intersil in vendor-prefixes.txt
Add AD Holdings Plc. to vendor-prefixes.
dt-bindings: Add Silicon Mitus vendor prefix
Removes OF_UNITTEST dependency on OF_DYNAMIC config symbol
pinctrl: fix up device tree bindings
DT: Vendors: Add Everspin
doc: add bindings document for altera fpga manager
drivers: of: Export of_reserved_mem_device_{init,release}
Allow bus clock specification as a common clock handle. This makes this
controller easier to use in a setup based on common clock framework.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clock-frequency property is meant to control the bus frequency for i2c bus
drivers, but it was incorrectly used to specify i2c controller input clock
frequency.
Introduce new attribute, opencores,ip-clock-frequency, that specifies i2c
controller clock frequency and make clock-frequency attribute compatible
with other i2c drivers. Maintain backwards compatibility in case
opencores,ip-clock-frequency attribute is missing.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Align compatible strings for several IP blocks present on Tegra chips
with the latest doctrine from the DT maintainers:
http://marc.info/?l=devicetree&m=142255654213019&w=2
The primary objective here is to avoid checkpatch warnings, per:
http://marc.info/?l=linux-tegra&m=142201349727836&w=2
DT binding text files have been updated for the following IP blocks:
- PCIe
- SOR
- SoC timers
- AHB "gizmo"
- APB_MISC
- pinmux control
- UART
- PWM
- I2C
- SPI
- RTC
- PMC
- eFuse
- AHCI
- HDA
- XUSB_PADCTRL
- SDHCI
- SOC_THERM
- AHUB
- I2S
- EHCI
- USB PHY
N.B. The nvidia,tegra20-timer compatible string is removed from the
nvidia,tegra30-timer.txt documentation file because it's already
mentioned in the nvidia,tegra20-timer.txt documentation file.
This second version takes into account the following requests from
Rob Herring <robherring2@gmail.com>:
- Per-IP block patches have been combined into a single patch
- Explicit documentation about which compatible strings are actually
matched by the driver has been removed. In its place is implicit
documentation that loosely follows Rob's prescribed format:
"Must contain '"nvidia,<chip>-pcie", "nvidia,tegra20-pcie"' where
<chip> is tegra30, tegra132, ..." [...] "You should attempt to
document known values of <chip> if you use it"
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dylan Reid <dgreid@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-i2c@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-pwm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
CM3232 is an advanced ambient light sensor with I2C protocol interface.
The I2C slave address is internally hardwired as 0x10 (7-bit). Writing
to configure register is byte mode, but reading ALS register requests to
use word mode for 16-bit resolution.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CLK_S_ICN_REG_0 hasn't existed for a while now. This was renamed
over a few commits, then finally removed in commit 5aa02b9 (ARM:
STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock).
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c-mux-idle-disconnect device tree property to PCA954x mux driver. The new
property forces the multiplexer to disconnect child buses in idle state. This is
used, for example, when there are several multiplexers on the same bus and the
devices on the underlying buses might have same I2C addresses.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[wsa: added a newline]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes I2C trivial-devices.txt DT documentation file to
reference isil (NASDAQ symbol and the most used prefix inside the
kernel) for Intersil.
It reverts 7c75c1d5e7 ("dt-bindings: Document deprecated device
vendor name to fix related warning").
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Rockchip I2C the controller drops SDA low slightly too soon to meet
the "repeated start" requirements.
>From my own experimentation over a number of rates:
- controller appears to drop SDA at .875x (7/8) programmed clk high.
- controller appears to keep SCL high for 2x programmed clk high.
The first rule isn't enough to meet tSU;STA requirements in
Standard-mode on the system I tested on. The second rule is probably
enough to meet tHD;STA requirements in nearly all cases (especially
after accounting for the first), but it doesn't hurt to account for it
anyway just in case.
Even though the repeated start requirement only need to be accounted
for during a small part of the transfer, we'll adjust the timings for
the whole transfer to meet it. I believe that adjusting the timings
in just the right place to switch things up for repeated start would
require several extra interrupts and that doesn't seem terribly worth
it.
With this change and worst case rise/fall times, I see 100kHz i2c
going to ~85kHz. With slightly optimized rise/fall (800ns / 50ns) I
see i2c going to ~89kHz. Fast-mode isn't affected much because
tSU;STA is shorter relative to tHD;STA there.
As part of this change we needed to account for the SDA falling time.
The specification indicates that this should be the same, but we'll
follow Designware's lead and add a binding. Note that we deviate from
Designware and assign the default SDA falling time to be the same as
the SCL falling time, which is incredibly likely.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: rebased to i2c/for-next]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The number of clock cycles to be written into the CLKDIV register
that determines the I2C clk high phase includes the rise time.
So to meet the timing requirements defined in the I2C specification
which defines the minimal time SCL has to be high, the rise time
has to taken into account. The same applies to the low phase with
falling time.
In my test on RK3288-Pink2 board, which is not an upstream board yet,
if external pull-up resistor is 4.7K, rise_ns is about 700ns.
So the measured high_ns is about 3900ns, which is less than 4000ns
(the minimum high_ns in I2C specification for Standard-mode).
To fix this bug min_low_ns should include fall time and min_high_ns
should include rise time.
This patch merged the patch from chromium project which can get the
rise and fall times for signals from the device tree. This allows us
to more accurately calculate timings. see:
https://chromium-review.googlesource.com/#/c/232774/
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
[wsa: fixed a typo in the docs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The highlight is the series that reworks the idle management on powernv, which
allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!" problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he asked that we
take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of the audit
maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a sysfs file,
so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for smt-enabled, and
the patch to add __force to get_user() so we can use bitwise types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUk+oCAAoJEFHr6jzI4aWADBAP/i/CJ+cu6o4mzNDdfs8bnxqn
RGZCSV+SrkTZPcoLbLiM9iaqq34ORVIn7hwkhkTz2/koluMVfTsqtVulMoFf+hVd
GTVt81MjMFzA3hM3bXEV58KRT79+64K54dLCe0F7OaD6f4AikKR4LLz/PY0EBMiZ
2h13uQlfglaMeYTsaD9eeUpIIKs7+PwsNqUknmN9We07WWfxWqnRpiTR4TYTMXx4
3lQPvCnnHokwDqjuKgwiqDVSaCfCl8laS1i+BPk0G0aRV1AnPDvR3MhgVb2IpNxX
Joxy2D1HSawwDhqHOsId8dkGZXOM4vzo+Y658qnC1XfThqE0MhA+kCfa5/b6xlOR
K7nDO5A41B6nXB3mMOQh/szTXSIa8KJRTR3ibbJJrMdF6F0TN0JLLQNUcmM4j/5D
vvgZEzvFNZhWX98ktlQLde2E4ClWJg6mWESCGSgJeVjIXaxe/6GneIa8vLKm5QMu
OoykNsASMDGqddYMGoYeX/mSsvjPjK0PDO2q19sPbkP8xpyDLx6J8xo+5hO4l8xc
0Cdb38ECfeno+w5oKAnjidHnz0KYBsuYFLeS+rV0b8sUSWAzfdEjSn2AVIQ8gLOv
IOCAqwZ5tL9EcUs+AKru5EHtBEV+2XB54xPRxfdFS/k+vYRE7MpS3ipxveIynN2l
eRxf9hsSO7ASNDd0b3ID
=GXdK
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In (6468276 i2c: designware: make SCL and SDA falling time
configurable) new device tree properties were added for setting the
falling time of SDA and SCL. The device tree bindings doc had a typo
in it: it forgot the "-ns" suffix for both properies in the prose of
the bindings.
I assume this is a typo because:
* The source code includes the "-ns"
* The example in the bindings includes the "-ns".
Fix the typo.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Fixes: 6468276b22 ("i2c: designware: make SCL and SDA falling time configurable")
Acked-by: Romain Baeriswyl <romain.baeriswyl@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.
CC: Rob Herring <robh+dt@kernel.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: devicetree@vger.kernel.org
CC: linux-doc@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch documents the device isl29028 with its vendor-prefix. Undocumented deprecated vendor-prefix
found by checkpatch also documented for compatibility reasons.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add dma support for i2c. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
DMA is optional, even DMA request unsuccessfully, i2c can also work well.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address is still handled using the old state
machine, it is sending the actual data that is done via DMA. This is
least intrusive and allows us to work with the message buffers directly
instead of preparing a custom buffer which involves copying the data
around.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed an uninitialized var problem]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Explicitly list the various SoC-specific compatible properties.
This allows checkpatch to validate DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
BQ32000 have "trickle chargers". Introduce a device tree binding for
specifying the trickle charger configuration for that.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jason Cooper <jason@lakedameon.net>
Cc: Matti Vaittinen <matti.vaittinen@nsn.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some DS13XX devices have "trickle chargers". Introduce a device tree
binding for the resistor and diode configuration for enabling trickle
charger.
Signed-off-by: Matti Vaittinen <matti.vaittinen@nsn.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HSI2C module on Exynos7 differs in the transfer status
bits. Transfer status bits were moved to INT_ENABLE and
INT_STATUS registers
This patch adds support for the HSI2C module on Exynos7.
1. Implementes a "hw" field in the variant struct to distinguish
the hardware.
2. Updates the dt-new compatible in dt-binding documenation
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull i2c updates from Wolfram Sang:
"Highlights:
- class based instantiation finally dropped for most embedded drivers
bringing boot up performance gains
- removed two drivers (one outdated, one a duplicate)
- ACPI has now operation region support (thanks to Lan Tianyu)
- the i2c-stub driver got overhauled and gained new features to
become more useful when writing i2c client drivers (thanks to
Guenter Roeck and Jean Delvare)
The rest is driver bugfixes, added bindings/ids, cleanups..."
* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: mpc: delete unneeded test before of_node_put
i2c: rk3x: fix interrupt handling issue
i2c: imx: Fix format warning for dev_dbg
i2c: qup: disable clks and return instead of just returning error
i2c: exynos5: always enable HSI2C
i2c: designware: add new bindings
i2c: gpio: Drop dead code in i2c_gpio_remove
i2c: pca954x: put the mux to disconnected state after resume
i2c: st: Update i2c timings
drivers/i2c/busses: use correct type for dma_map/unmap
i2c: i2c-st: Use %pa to print 'resource_size_t' type
i2c: s3c2410: resume the I2C controller earlier
i2c: stub: Avoid an array overrun on I2C block transfers
i2c: i801: Add device ID for Intel Wildcat Point PCH
i2c: i801: Fix the alignment of the device table
i2c: stub: Add support for banked register ranges
i2c: stub: Remember the number of emulated chips
i2c: stub: Add support for SMBus block commands
i2c: efm32: correct namespacing of location property
i2c: exynos5: remove extra line and fix an assignment
...
Heiko Schocher provided a driver for TI TMP103.
Kamil Debski provided a driver for pwm-controlled fans.
Neelesh Gupta provided a driver for power, fan rpm, voltage and temperature
reporting on powerpc/powernv systems.
Scott Kanowitz provided a driver supporting Lattice's POWR1220 power manager IC.
Richard Zhu provided a pmbus front-end driver for TPS40422.
Frans Klaver added support for TMP112 to the lm75 driver.
Johannes Pointner added support for EPCOS B57330V2103 to the ntc_thermistor
driver.
Guenter Roeck added support for TMP441 and TMP442 to the tmp421 driver.
Axel Lin converted several drivers to the new hwmon API (36 of them, if I
counted correctly), and cleaned up many of the drivers along the way.
There are also a number of patches fixing bugs discovered while testing
Axel's changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9j+M
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Notable changes:
- Heiko Schocher provided a driver for TI TMP103.
- Kamil Debski provided a driver for pwm-controlled fans.
- Neelesh Gupta provided a driver for power, fan rpm, voltage and
temperature reporting on powerpc/powernv systems.
- Scott Kanowitz provided a driver supporting Lattice's POWR1220
power manager IC.
- Richard Zhu provided a pmbus front-end driver for TPS40422.
- Frans Klaver added support for TMP112 to the lm75 driver.
- Johannes Pointner added support for EPCOS B57330V2103 to the
ntc_thermistor driver.
- Guenter Roeck added support for TMP441 and TMP442 to the tmp421
driver.
- Axel Lin converted several drivers to the new hwmon API (36 of
them, if I counted correctly), and cleaned up many of the drivers
along the way.
There are also a number of patches fixing bugs discovered while
testing Axel's changes"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (88 commits)
hwmon: (g762) Use of_property_read_u32 at appropriate place
hwmon: (sis5595) Prevent overflow problem when writing large limits
hwmon: (gpio-fan) Prevent overflow problem when writing large limits
hwmon: (ibmpowernv) Use of_property_read_u32 at appropriate place
hwmon: (lm85) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Avoid forward declaration
hwmon: (lm78) Convert to devm_hwmon_device_register_with_groups
hwmon: (max6697) Use of_property_read_bool at appropriate places
hwmon: (pwm-fan) Make SENSORS_PWM_FAN depend on OF
hwmon: (pwm-fan) Remove duplicate dev_set_drvdata call
hwmon: (nct6775) Remove num_attr_groups from struct nct6775_data
hwmon: (nct6775) Update module description and Kconfig for NCT6106D and NCT6791D
hwmon: (adt7411) Convert to devm_hwmon_device_register_with_groups
hwmon: (g762) Convert to hwmon_device_register_with_groups
hwmon: (emc2103) Convert to devm_hwmon_device_register_with_groups
hwmon: (smsc47m1) Avoid forward declaration
hwmon: (smsc47m192) Convert to devm_hwmon_device_register_with_groups
hwmon: (smsc47m192) Avoid forward declaration
hwmon: (max1668) Make max1668_addr_list array const
hwmon: (max6639) Make normal_i2c array const
...
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Olof Johansson pointed out that usually the company name is picked as
namespace prefix to specific properties. So expect "energymicro,location"
but fall back to the previously introduced name "efm32,location".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the mma8452 to be described in the device tree.
Since no device specific binding attributes exist the trivial
I2C binding is sufficient to describe the compatible string.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
P2WI (Push/Pull 2 Wire Interface) is an SMBus like bus used to communicate
with some PMICs (like the AXP221).
Document P2WI DT bindings which are pretty much the same as the one defined
for the marvell's mv64xxx controller.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following updates for 3.16:
- major cleanups to the rcar and sh_mobile drivers
- removal of nuc900 driver which had a compile error for years
- usual bunch of driver updates, bugfixes and cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: pca954x: Fix compilation without CONFIG_GPIOLIB
i2c: mux: pca954x: Use the descriptor-based GPIO API
i2c: mpc: insert DR read in i2c_fixup()
i2c: bfin: turn to Resource-managed API in probe function
i2c: Make of_device_id array const
i2c: remove unnecessary OOM messages
i2c: designware-pci: Add Haswell PCI IDs
i2c: designware: Add runtime PM hooks
i2c: designware: Disable device on system suspend
i2c: nuc900: remove driver
i2c: imx: update i2c clock divider for each transaction
i2c: imx: fix the i2c bus hang issue when do repeat restart
i2c: rcar: update copyright and license information
i2c: rcar: janitorial cleanup after refactoring
i2c: rcar: reuse status bits as enable bits
i2c: rcar: remove spinlock
i2c: rcar: refactor status bit handling
i2c: rcar: refactor setting up msg
i2c: rcar: check bus free before first message
i2c: rcar: refactor irq state machine
...
On ARM Chromebooks we have a few devices that are accessed by both the
AP (the main "Application Processor") and the EC (the Embedded
Controller). These are:
* The battery (sbs-battery).
* The power management unit tps65090.
On the original Samsung ARM Chromebook these devices were on an I2C
bus that was shared between the AP and the EC and arbitrated using
some extranal GPIOs (see i2c-arb-gpio-challenge).
The original arbitration scheme worked well enough but had some
downsides:
* It was nonstandard (not using standard I2C multimaster)
* It only worked if the EC-AP communication was I2C
* It was relatively hard to debug problems (hard to tell if i2c issues
were caused by the EC, the AP, or some device on the bus).
On the HP Chromebook 11 the design was changed to:
* The AP/EC comms were still i2c, but the battery/tps65090 were no
longer on the bus used for AP/EC communication. The battery was
exposed to the AP through a limited i2c tunnel and tps65090 was
exposed to the AP through a custom Linux driver.
On the Samsung ARM Chromebook 2 the scheme is changed yet again, now:
* The AP/EC comms are now using SPI for faster speeds.
* The EC's i2c bus is exposed to the AP through a full i2c tunnel.
The upstream "tegra124-venice2" uses the same scheme as the Samsung
ARM Chromebook 2, though it has a different set of components on the
other side of the bus.
This driver supports the scheme used by the Samsung ARM Chromebook 2.
Future patches to this driver could add support for the battery tunnel
on the HP Chromebook 11 (and perhaps could even be used to access
tps65090 on the HP Chromebook 11 instead of using a special driver,
but I haven't researched that enough).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
