This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters. These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions). New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define. This patch corrects that so the
correct bit is checked on igp PHY types.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID and related support for 82583 mac.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Radheka Godse <radheka.godse@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses an issue where we did not restart auto-negotiation on
serdes links when the link partner was disabled and re-enabled. It includes
reworking the serdes link detect mechanism to be a state machine for
82571 and 82572 parts only.
Signed-off-by: dave graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a hardware errata in some revisions of the 82574 that needs
to be worked around in the driver by setting a register bit at init.
If this bit is not set A0 versions of the 82574 can generate
tx hangs.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this. To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split. New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables ECC correction for the packet buffer on all 82571
silicon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new part has the same feature set as previous parts with the addition
of MSI-X support.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for new LOM devices on the latest generation ICHx platforms.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.
This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).
To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several stats registers are completely unused and we just waste pci
bus time reading them. We also omit using the high 32 bits of the GORC/
GOTC counters. We can just read clear them and only read the low registers.
Mii-tool can also break es2lan if it executes a MII PHY register
ioctl while the device is in autonegotiation. Unfortunately it seems
that several applications and installations still perform this ioctl
call periodically and especially in this crucial startup time. We
can fool the ioctl by providing fail safe information that mimics
the "down" link state and only perform the dangerous PHY reads once
after link comes up to fill in the real values. As long as link
stays up the information will not change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With multiple queues coming into the code these base control
registers need to be made into arrays.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reorganization moves the PHY status into a separate
struct. Flow Control setup is moved into this struct as well
and frame size away from here into the adapter struct where its
inly use is.
The post-link-up code is now a separate function and moved out
of the watchdog function itself. This allows us to track the
es2lan restart issue a bit easier.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename this function to be consistent with function naming (verb first)
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adjusting the comment blocks here to be code-style compliant. no
code changes.
Changed some copyright dates to 2008.
Indentation fixes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A small bug crawled in the -DDEBUG enabled code. Fix this to
properly call the backreference device name.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
