Do some minor tidy-up.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we call hisi_sas_softreset_ata_disk() in
hisi_sas_I_T_nexus_reset().
If this fails for open reject reason, there is no reason to fail the IT
nexus reset, so only fail for TMF_RESP_FUNC_FAILED.
Some other strings spilled over multiple lines are reunited.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the function of hisi_sas_init_device(), we added ops->hardreset() to
clear affiliation of STP target port or handle [STP pending] state.
Function hisi_sas_init_device() will be called when a device is found or
during controller reset. At controller reset, we call
hisi_sas_init_device() to re-init the disks, so calling hardreset() is
unnecessary and it also will cause some delay at controller reset.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_init_device(), the log is as follows when error for
hardreset:
hisi_sas_v3_hw 0000:74:02.0: SATA disk hardreset fail: 0xffffffed
Actually if hardreset failed, its return value is negative, so change the
print format from %x to %d.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit efdcad62e7 ("scsi: hisi_sas: Set PHY linkrate when
disconnected"), we use the sas_phy_data.enable flag to track whether the
PHY was enabled or not, so that we know if we should set the PHY negotiated
linkrate at SAS_LINK_RATE_UNKNOWN or SAS_PHY_DISABLED.
However, it is not proper to use sas_phy_data.enable, since it is only set
when libsas attempts to set the PHY disabled/enabled; hence, it may not
even have an initial value.
As a solution to this problem, introduce hisi_sas_phy.enable to track
whether the PHY is enabled or not, so that we can set the negotiated
linkrate properly when the PHY comes down.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there are two scenarioes which may cause PHY state of hardware
(which is 0) is inconsistent with the state held in software:
- Unplug SAS wire before get_phys_state when SAS controller reset, then the
interrupts of phy down are ignored, phy state is 0 before reset, and it
also gets 0 after reset, so phy down doesn't occur even if unplugged SAS
wire;
- For v3 hw later version, it will close bus when 2 bit ECC error occurs.
So if unplug SAS wire at that time, interrupts of phy down also not
occur. So at last it will cause host reset. It also get phy state 0
before and after reset, the same issue occurs.
To solve it, use hisi_sas_phy_down() directly in rescan topology function.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add host reset interface to make it easier for testing the host reset
feature.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.
In commit ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.
We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.
Fixes: ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
If we exchange SAS expander from one SAS controller to other SAS controller
without powering it down, the STP target port will maintain previous
affiliation and reject all subsequent connection requests from other STP
initiator ports with OPEN_REJECT (STP RESOURCES BUSY).
To solve this issue, send HARD RESET to clear the previous affiliation of
STP target port according to SPL (chapter 6.19.4).
We (re-)introduce dev status flag to know if to sleep in NEXUS reset code
or not for remote PHYs. The idea is that if the device is being
initialised, we don't require the delay, and caller would wait for link to
be established, cf. sas_ata_hard_reset().
Co-developed-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$
This patch fixes the driver code to set it properly when the PHY comes
down.
If the PHY had been enabled, then set unknown; otherwise, flag as disabled.
The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.
However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.
As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is internal
to libsas.
I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For internal IO and SMP IO, there is a time-out timer for them. In the
timer handler, it checks whether IO is done according to the flag
task->task_state_lock.
There is an issue which may cause system suspended: internal IO or SMP IO
is sent, but at that time because of hardware exception (such as inject
2Bit ECC error), so IO is not completed and also not timeout. But, at that
time, the SAS controller reset occurs to recover system. It will release
the resource and set the status of IO to be SAS_TASK_STATE_DONE, so when IO
timeout, it will never complete the completion of IO and wait for ever.
[ 729.123632] Call trace:
[ 729.126791] [<ffff00000808655c>] __switch_to+0x94/0xa8
[ 729.133106] [<ffff000008d96e98>] __schedule+0x1e8/0x7fc
[ 729.138975] [<ffff000008d974e0>] schedule+0x34/0x8c
[ 729.144401] [<ffff000008d9b000>] schedule_timeout+0x1d8/0x3cc
[ 729.150690] [<ffff000008d98218>] wait_for_common+0xdc/0x1a0
[ 729.157101] [<ffff000008d98304>] wait_for_completion+0x28/0x34
[ 729.165973] [<ffff000000dcefb4>] hisi_sas_internal_task_abort+0x2a0/0x424 [hisi_sas_test_main]
[ 729.176447] [<ffff000000dd18f4>] hisi_sas_abort_task+0x244/0x2d8 [hisi_sas_test_main]
[ 729.185258] [<ffff000008971714>] sas_eh_handle_sas_errors+0x1c8/0x7b8
[ 729.192391] [<ffff000008972774>] sas_scsi_recover_host+0x130/0x398
[ 729.199237] [<ffff00000894d8a8>] scsi_error_handler+0x148/0x5c0
[ 729.206009] [<ffff0000080f4118>] kthread+0x10c/0x138
[ 729.211563] [<ffff0000080855dc>] ret_from_fork+0x10/0x18
To solve the issue, callback function task_done of those IOs need to be
called when on SAS controller reset.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA
mask value succeeded.
[mkp: fixed commit message]
Fixes: e4db40e7a1 ("scsi: hisi_sas: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do some very minor tidy-up, for things like needlessly initing variable and
not leaving whitespace before quote endings.
Originally-from: Xiang Chen <chenxiang66@hisilicon.com>
Originally-from: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For auto-control irq affinity mode, choose the dq to deliver IO according
to the current CPU.
Then it decreases the performance regression that fio and CQ interrupts are
processed on different node.
For user control irq affinity mode, keep it as before.
To realize it, also need to distinguish the usage of dq lock and sas_dev
lock.
We mark as experimental due to ongoing discussion on managed MSI IRQ
during hotplug:
https://marc.info/?l=linux-scsi&m=154876335707751&w=2
We're almost at the point where we can expose multiple queues to the upper
layer for SCSI MQ, but we need to sort out the per-HBA tags performance
issue.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To support queue mapped to a CPU, it needs to be ensured that issuing an
internal abort is safe, in that it is guaranteed that an internal abort is
processed for a single IO or a device after all the relevant command(s)
which it is attempting to abort have been processed by the controller.
Currently we only deliver commands for any device on a single queue to
solve this problem, as we know that commands issued on the same queue will
be processed in order, and we will not have a scenario where the internal
abort is racing against a command(s) which it is trying to abort.
To enqueue commands on queue mapped to a CPU, choosing a queue for an
command is based on the associated queue for the current CPU, so this is
not safe for internal abort since it would definitely not be guaranteed
that commands for the command devices are issued on the same queue.
To solve this issue, we take a bludgeoning approach, and issue a separate
internal abort on any queue(s) relevant to the command or device, in that
we will be guaranteed that at least one of these internal aborts will be
received last in the controller.
So, for aborting a single command, we can just force the internal abort to
be issued on the same queue as the command which we are trying to abort.
For aborting all commands associated with a device, we issue a separate
internal abort on all relevant queues. Issuing multiple internal aborts in
this fashion would have not side affect.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add an interface to manually trigger a debugfs dump.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for DIX to v3 hw driver.
For this, we build upon support for DIF, most significantly is adding new
DMA map and unmap paths.
Some pre-existing macro precedence issues are also tidied. They were
detected by checkpatch --strict.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This call must have been missed when I reworked the debugfs feature for
upstreaming, so add it back.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse detected some problems in the driver, so tidy them up.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some sizes we allocate for debugfs structure are incorrect, so fix them.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hot-plugging SAS wire of direct hard disk backplane may cause disk lost. We
have done this test with several types of SATA disk from different venders,
and only two models from Seagate has this problem, ST4000NM0035-1V4107 and
ST3000VM002-1ET166.
The root cause is that the disk doesn't send D2H frame after OOB finished.
SAS controller will issue phyup interrupt only when D2H frame is received,
otherwise, will be waiting there all the time.
When this issue happen, we can find the disk again with link reset. To fix
this issue, we setup an timer after OOB finished. If the PHY is not up in
20s, do link reset. Notes: the 20s is an experience value.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS controller cannot support a programmed minimum linkrate of > 1.5G
(it will always negotiate to 1.5G at least), so just reject it.
This solves a strange situation where the PHY negotiated linkrate may be
less than the programmed minimum linkrate.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_alloc(), parameter shost is not used, so remove it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When issing a hardreset to a SATA device when running IO, it is possible
that abnormal CQs of the device are returned. Then enter error handler, it
doesn't enter function hisi_sas_abort_task() as there is no timeout IO, and
it doesn't set device as HISI_SAS_DEV_EH. So when hardreset by libata
later, it actually doesn't issue hardreset as there is a check to judge
whether device is in error.
For this situation, actually need to hardreset the device to recover.
So remove the check of sas_dev status in hisi_sas_I_T_nexus_reset().
Before we add the check to avoid the endless loop of reset for
directly-attached SATA device at probe time, actually we flutter it for
it, so it is not necessary to add the check now.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Send primitive NOTIFY to SSP situation only, or it causes underflow issue
when sending IO. Also rename hisi_sas_hw.sl_notify() to hisi_sas_hw.
sl_notify_ssp().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates debugfs file for ITCT and adds file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse can detect some type casting issues in the debugfs code, so fix it
up.
Also a missing static qualifier is added to hisi_sas_debugfs_to_reg_name().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for IOST and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for DQ and add file operations
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for CQ and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for port register and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for global register and add file
operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch takes snapshot for global regs, port regs, CQ, DQ, IOST, ITCT.
Add code for snapshot trig and generate dump directory.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allocates snapshot memory for global reg, port regs, CQ, DQ,
IOST, ITCT.
When we fail to allocate memory for some registers, we free the memory
and set hisi_sas_debugfs_enable as 0 to stop loading debugfs from running.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates root directory at hisi_sas_init() and generates device
directory when we probe device driver.
And we remove the root directory at hisi_sas_exit(), but recursively
delete device directory when we remove device driver.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sht->sg_tablesize is set in the driver, and it will be assigned to
shost->sg_tablesize in SCSI mid-layer. So it is not necessary to assign
shost->sg_table one more time in the driver.
In addition to the change, change each scsi_host_template.sg_tablesize
to HISI_SAS_SGE_PAGE_CNT instead of SG_ALL.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate the codes related to dma_map/unmap in hisi_sas_task_prep() to
reduce complexity, with a view to add DIF/DIX support.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patchset fixes some warnings detected by the sparse tool, like these:
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: got restricted __le16 [usertype] <noident>
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: got restricted __le16 [usertype] <noident>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_task_prep(), we check asd_sas_port, but in function
hisi_sas_task_exec(), we already refer to asd_sas_port by using function
dev_to_hisi_hba() implicitly. So to avoid this possible invalid
dereference, relocate the check to function hisi_sas_task_prep().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently all the three HBA (v1/v2/v3 HW) share the same host attributes.
To support each HBA having separate attributes in future, create per-HBA
attributes.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a NULL pointer dereference in case *slot* happens to be NULL at
lines 1053 and 1878:
struct hisi_sas_cq *cq =
&hisi_hba->cq[slot->dlvry_queue];
Notice that *slot* is being NULL checked at lines 1057 and 1881:
if (slot), which implies it may be NULL.
Fix this by placing the declaration and definition of variable cq, which
contains the pointer dereference slot->dlvry_queue, after slot has been
properly NULL checked.
Addresses-Coverity-ID: 1474515 ("Dereference before null check")
Addresses-Coverity-ID: 1474520 ("Dereference before null check")
Fixes: 584f53fe5f ("scsi: hisi_sas: Fix the race between IO completion and timeout for SMP/internal IO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use the IPTT defined in LLDD to identify IOs. Actually for
IOs which are from the block layer, they have tags to identify them. So
for those IOs, use tag of the block layer directly, and for IOs which is
not from the block layer (such as internal IOs from libsas/LLDD), reserve
96 IPTTs for them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SMP/internal IO times out, we will possibly free the task immediately.
However if the IO actually completes at the same time, the IO completion
may refer to task which has been freed.
So to solve the issue, flush the tasklet to finish IO completion before
free'ing slot/task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In evaluating hisi_hba, the sas_port may be NULL, so for safety relocate
the the check to value possible NULL deference.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At directly attached situation, if the user modifies the sysfs interface
of maximum_linkrate and minimum_linkrate to renegotiate the linkrate
between SAS controller and target, the value of both files mentioned
above should have change to user setting after renegotiate is over, but
it remains unchanged.
To fix this bug, maximum_linkrate and minimum_linkrate will be directly
fed back to relevant sas_phy structure.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Acked-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In task start delivery function, we need to add a memory barrier to prevent
re-ordering of reading memory by hardware. Because the slot data is set in
task prepare function and it could be running in another CPU.
This patch adds an memory barrier after s->ready is read in the task start
delivery function, and uses WRITE_ONCE() in the places where s->ready is
set to ensure that the compiler does not re-order.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
