Use more linkmode_* helpers rather than open-coding the bitmap
operations.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in phylink.c:
../drivers/net/phy/phylink.c:595: warning: Function parameter or member 'config' not described in 'phylink_create'
../drivers/net/phy/phylink.c:595: warning: Excess function parameter 'ndev' description in 'phylink_create'
Fixes: 8796c8923d ("phylink: add documentation for kernel APIs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reported-by: Shaul Ben-Mayor <shaulb@marvell.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.
Since commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:
% ip link set up dev eth0
------------[ cut here ]------------
called from state UP
WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
Modules linked in:
CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
NIP: c0227bf0 LR: c0227bf0 CTR: c004d224
REGS: df547720 TRAP: 0700 Not tainted (5.2.0+)
MSR: 00029000 <CE,EE,ME> CR: 24002822 XER: 00000000
GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
NIP [c0227bf0] phy_start+0x74/0xc0
LR [c0227bf0] phy_start+0x74/0xc0
Call Trace:
[df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
[df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
[df547828] [c023cf08] gfar_enet_open+0x364/0x374
[df547898] [c029d870] __dev_open+0xe4/0x140
[df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
[df5478f8] [c029dc28] dev_change_flags+0x20/0x54
[df547918] [c02ae304] do_setlink+0x310/0x818
[df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df547c28] [c02b222c] rtnl_newlink+0x48/0x68
[df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
--- interrupt: c01 at 0xfd4e030
LR = 0xfd4e010
Instruction dump:
813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
---[ end trace d4c095aeaf6ea998 ]---
and
% ip link set down dev eth0
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88
<...>
Call Trace:
[df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
[df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
[df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
[df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
[df581858] [c0225608] phylink_stop+0x7c/0xe4
[df581868] [c023c57c] stop_gfar+0x7c/0x94
[df581888] [c023c5b8] gfar_close+0x24/0x94
[df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
[df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
[df5818f8] [c029dc28] dev_change_flags+0x20/0x54
[df581918] [c02ae304] do_setlink+0x310/0x818
[df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df581c28] [c02b222c] rtnl_newlink+0x48/0x68
[df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df581f38] [c000d1d8] ret_from_syscall+0x0/0x38
<...>
---[ end trace d4c095aeaf6ea999 ]---
SFP modules with the 1000Base-X interface are not affected.
Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.
Fixes: 2179626156 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid reducing the support mask as a result of the interface type
selected for SFP modules, or when setting the link settings through
ethtool - this should only change when the supported link modes of
the hardware combination change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfp-bus code now no longer has any use for the network device
structure, so remove its use.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add attach and detach methods for SFP buses, which will allow us to get
rid of the netdev storage in sfp-bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using GPIO interrupts with a fixed-link GPIO rather than
polling the GPIO every second and invoking the phylink resolution. This
avoids unnecessary calls to mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev used in the phylink ioctl emulation is never used, so let's
remove it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest addition to the PHYLINK infrastructure, we are faced
with a decision on when to print necessary info using the struct
net_device and when with the struct device.
Add a series of macros that encapsulate this decision and replace all
uses of netdev_err&co with phylink_err.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PHYLINK_DEV operation type, the PHYLINK infrastructure can work
without an attached net_device. For printing usecases, instead, a struct
device * should be passed to PHYLINK using the phylink_config structure.
Also, netif_carrier_* calls ar guarded by the presence of a valid
net_device. When using the PHYLINK_DEV operation type, we cannot check
link status using the netif_carrier_ok() API so instead, keep an
internal state of the MAC and call mac_link_{down,up} only when the link
changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that reduces the clutter in phylink_resolve
around calling the .mac_link_up/.mac_link_down driver callbacks. In a
further patch this logic will be extended to emit notifications in case
a net device does not exist.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not update the link interface mode while the link is down to avoid
spurious link interface changes.
Always call mac_config if we have a PHY to propagate the pause mode
settings to the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.
This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().
Fixes: b5bfc21af5 ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide phylink_init_eee() to allow MAC drivers to initialise PHY EEE
from within the ethtool set_eee() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's little point calling mac_config() when the link is down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers have the GPLv2 license text. They then either have
a MODULE_LICENSE() of GPLv2+, or an SPDX tag of GPLv2+.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup with others when there are contradictions.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink has some useful helpers to working with linkmode bitmaps.
Move them to there own header so other code can use them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC drivers to use in their validate callback to deal
with 2500BaseX vs 1000BaseX modes, where the hardware supports both
but it is not possible to automatically select between them.
This helper defaults to 1000BaseX, as that is the 802.3 standard, and
will allow users to select 2500BaseX either by forcing the speed if
AN is disabled, or by changing the advertising mask if AN is enabled.
Disabling AN is not recommended as it is only the speed that we're
interested in controlling, not the duplex or pause mode parameters.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_GPIOLIB is disabled, gpiod_put() becomes a stub that produces a
warning, this helped identify that we could be attempting to release a NULL
pl->link_gpio GPIO descriptor, so guard against that.
Fixes: daab3349ad ("net: phy: phylink: Release link GPIO")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed link with a link GPIO, we need to poll that GPIO to
determine link state changes. This is consistent with what fixed_phy.c does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO provider for the link GPIO line might require the use of the
_cansleep() API, utilize that. This is safe to do since we run in workqueue
context.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in comments and error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of working on MII time stamping infrastructure, I was trying
to figure out how netdev->phydev gets assigned, and I stumbled across
this. Ever since the new phylink code came in, the field is assigned
twice.
The function, phylink_connect_phy(), calls
phy_attach_direct()
phylink_bringup_phy()
and phy_attach_direct() sets
dev->phydev = phydev;
but phylink_bringup_phy() then sets the same field again:
pl->netdev->phydev = phy;
Similarly, the function, phylink_of_phy_connect(), calls
of_phy_attach()
phy_attach_direct()
phylink_bringup_phy()
The removal code is also duplicated:
phylink_disconnect_phy()
pl->netdev->phydev = NULL;
phy_disconnect()
phy_detach()
phydev->attached_dev->phydev = NULL;
This patch removes the redundant assignments, restricting manipulation
of the netdev.phydev field to phy_attach_direct() and phy_detach().
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Negotiate the interface format with the MAC rather than requiring it to
be a fixed type specified solely by the SFP module. This allows modules
that can work with several different interface signalling formats to
select a format compatible with the MAC - for example, a Fiber module
supporing Gigabit ethernet and faster connected to a Gigabit only MAC
needs to select the 1000BASE-X mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'mode' is actually constant through phylink_sfp_module_insert(), so
remove it and replace it with the enumerated constant.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we disable the netdev carrier, we fail to report in the kernel
log that the link went down. Fix this.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we mark AN as enabled at boot time, rather than leaving
it disabled. This is noticable if your SFP module is fiber, and
it supports faster speeds than 1G with 2.5G support in place.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the ethtool settings, ensure that the validated PHY
interface mode is propagated to the current link settings, so that
2500BaseX can be selected.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attaching more than one PHY to phylink is bad news, as we store a
pointer to the PHY in a single location. Error out if more than one
PHY is attempted to be attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ASSERT_RTNL() rather than WARN_ON(!lockdep_rtnl_is_held()) which
stops working when lockdep fires, and we end up with lots of warnings.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike the various of_* routines to fetch properties, fwnode_* routines can
have an early check against a NULL fwnode_handle reference which makes them
return -EINVAL (see fwnode_call_int_op), thus making it virtually impossible to
differentiate what type of error is going on.
Have an early check in phylink_register_sfp() so we can keep proceeding with
the initialization, there is not much we can do without a valid fwnode_handle
except return early and treat this similarly to -ENOENT.
Fixes: 8fa7b9b6af ("phylink: convert to fwnode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to what PHYLIB already does, make sure that
PHY_INTERFACE_MODE_MOCA is reported as PORT_BNC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_get_fixed_state() currently consults an optional "link_gpio"
GPIO descriptor, expand this mechanism to allow specifying a custom
callback. This is necessary to support out of band link notifcation
(e.g: from an interrupt within a MMIO register).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some subsystems like DSA may be trying to connect to a PHY through OF first,
and then attempt a connect using a local MDIO bus, remove the error message:
"unable to find PHY node" so we can let MAC drivers whether to print it or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may not always be able to resolve a correct phy_interface_t value before
actually connecting to the PHY device, when that happens, just have
phylink_connect_phy() utilize what the PHY device/driver provided.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let subsystems like DSA fully utilize PHYLINK, we need to be able
to communicate phy_device::flags from of_phy_{connect,attach} even when using
PHYLINK APIs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phylink to fwnode, switching phylink_create() from taking a
device_node to taking a fwnode_handle. This will allow other firmware
systems to take advantage of sfp/phylink support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert sfp-bus to use fwnode rather than device_node internally, so
we can support more than just device tree firmware.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add kernel-doc documentation for phylink kernel APIs, and link it into
the networking kapi documentation under "Network device support".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restart 802.3z negotiation when the net device is brought up to ensure
that the link partner has our current link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_init_eee() serves no purpose, remove it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for handling the faster 2.5G and 10G link modes when used
with SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the handling of SGMII and 802.3z is now the same, combine the
MLO_AN_xxx constants into a single MLO_AN_INBAND, and use the PHY
interface mode to distinguish between Cisco SGMII and 802.3z.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code handling SGMII and 802.3z is essentially the same, except that
we assume 802.3z has no PHY. Re-organise the code such that these cases
are merged, and exclude 802.3z mode from having a PHY attached. This
results in the same link handling behaviour as before.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use phy_interface_mode_is_8023z() helper to identify the
interface modes that use 802.3z negotiation. Use it in phylink's
phylink_mac_an_restart().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we tell the MAC to take the link down when phylink_stop()
is called, and that this completes prior to phylink_stop() returns.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/phy/phylink.c:570:6: warning:
symbol 'phylink_phy_change' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform a number of stylistic changes to phylink.c, sfp.c and sfp-bus.c:
- align with netdev-style comments
- align function arguments to the opening parenthesis
- remove blank lines
- fixup a few lines over 80 columns
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ret" isn't necessarily initialized here.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in-band autonegotation support for 10GBase-KR mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading module EEPROMs through phylink.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
