The I2C2 pins are already used and the following errors are seen:
imx27-pinctrl 10015000.iomuxc: pin MX27_PAD_I2C2_SDA already requested by 10012000.i2c; cannot claim for 1001d000.i2c
imx27-pinctrl 10015000.iomuxc: pin-69 (1001d000.i2c) status -22
imx27-pinctrl 10015000.iomuxc: could not request pin 69 (MX27_PAD_I2C2_SDA) from group i2c2grp on device 10015000.iomuxc
imx-i2c 1001d000.i2c: Error applying setting, reverse things back
imx-i2c: probe of 1001d000.i2c failed with error -22
Fix it by adding the correct I2C1 IOMUX entries for the pinctrl_i2c1 group.
Cc: <stable@vger.kernel.org>
Fixes: 61664d0b43 ("ARM: dts: imx27 phyCARD-S pinctrl")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AM5 IDK boards have TC358778 DPI-to-DSI bridge. Two different DSI panel
models are used with the AM5 IDKs, and these panels are added with DT
overlays. The AM5 IDKs can also be used without any panel.
Add TC358778 data to the am57xx-idk-common.dtsi, but set the status to
disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard.org BeagleBone AI is an open source hardware single
board computer based on the Texas Instruments AM5729 SoC featuring
dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital
signal processor (DSP), quad-core embedded vision engine (EVE),
Arm Cortex-M4 processors, dual programmable realtime unit
industrial control subsystems and more. The board features 1GB
DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash,
1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion
headers.
For more information, refer to:
https://beaglebone.ai
This patch introduces the BeagleBone AI device tree.
Note that the device use the "ti,tpd12s016" component which is
software compatible with "ti,tpd12s015". Thus we only use the
latter driver.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Even though commit cfb5d65f25 ("ARM: dts: dra7: Add bus_dma_limit
for L3 bus") added bus_dma_limit for L3 bus, the PCIe controller
gets incorrect value of bus_dma_limit.
Fix it by adding empty dma-ranges property to axi@0 and axi@1
(parent device tree node of PCIe controller).
Cc: stable@kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcbb63b802 ("ARM: dts: dra7: Separate AM57 dtsi files"),
the m_can node was inherited from dra76x.dtsi but the IP is not
connected on the idk board. Disable the node to reflect this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boot regression fix for N950/N9
We need to tag RNG as disabled for N950/N9 as it blocked by the secure
mode. We have a similar change done for N900, but I missed adding it
for N950/N9 with the recent RNG changes.
* tag 'omap-for-v5.6/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: OMAP3: disable RNG on N950/N9
Link: https://lore.kernel.org/r/pull-1585340588-558327@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Linux Automation MC-1 is a SBC built around the Octavo Systems
OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and
a PMIC. The board has eMMC and a SD slot for storage and GbE
for both connectivity and power.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
While all sleep pinctrl group labels now follow a fixed naming scheme,
node _names_ for these groups don't:
- Some use ${dev}-[0-9], where the suffix is the normal group suffix + 1
- Some use ${dev}-sleep-[0-9], where suffix is the normal group suffix
- The <dc node uses ${dev}-[a-z]-[0-9], where the letter matches the
phandle and the number suffix is the normal group's suffix + 1
For uniformity, standardize on using ${dev}-[0-9]+ for all normal
pinctrl groups and ${dev}-sleep-[0-9]+ for all sleep pinctrl groups.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Some labels follow the *_sleep_pins_* naming scheme, but some also use
*_pins_sleep_*. Because most labels use the former and for uniformity
with variants like sdmmc1_b4_pins_a and sdmmc1_dir_pins_a, adopt the
*_sleep_pins_* scheme throughout.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
With the cell sizes specified in the SoC DTSIs in a previous commit,
individual boards no longer need to specify them, thus drop them.
No functional change.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The cell count for address and size is defined by the binding and not
something a board would change. Avoid each board adding this
boilerplate by having the cell size specification in the SoC DTSI.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In the original stm32mp157c.dtsi, the GPU was disabled as some SoC
variants lacked a GPU. We now have separate a dtsi for each SoC
variant and variants without a GPU lack the node altogether.
As we need no board support for using the GPU, enable it by default
and while at it remove the now redundant status = "okay" in existing
board device trees.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
Since its inception the module was meant to be disabled by default, but
the original commit failed to add the relevant property.
Fixes: 4aba4cf820 ("ARM: dts: bcm2835: Add the DSI module nodes and clocks")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Y Soft yapp4 platform supports up to two Ethernet ports.
The Ursa board though has only one Ethernet port populated and that is
the port@2. Since the introduction of this platform into mainline a wrong
port was deleted and the Ethernet could never work. Fix this by deleting
the correct port node.
Fixes: 87489ec3a7 ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Introduce dtsi with overlay configuration for enabling UHS-I
for Colibri iMX6S/DL V1.1x re-design.
2. Introduce new dts for the Colibri iMX6S/DL V1.1x
on Colibri Evaluation Carrier Board V3.x. However, disable 1.8V for
the Colibri Evaluation Board since this carrier board has 3.3V pull-ups on.
3. Provide proper configuration for VGEN3, which allows that rail to
be automatically switched to 1.8 volts for proper UHS-I operation mode.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu-core is supposed to list its supply separately, add
supply for cpu1.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7 uses cpufreq-dt driver which requires the CPU supply name to be
either "cpu0-supply" or "cpu-supply", correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The H3 and H5 SoCs contain a message box that can be used to send
messages and interrupts back and forth between the ARM application CPUs
and the ARISC coprocessor. Add a device tree node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The A83T SoC contains a message box that can be used to send messages
and interrupts back and forth between the ARM application CPUs and the
ARISC coprocessor. Add a device tree node for it.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
OPP table value is get from orangepi lichee linux-3.4
kernel driver.
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is new version of A20-OLinuXino-LIME with eMMC storage. The
card routing is the same as in A20-OLinuXino-LIME2-eMMC, so this
is basically copy/paste.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit
0698fac4ac ("efi/arm: Clean EFI stub exit code from cache instead of avoiding it")
introduced a PC-relative reference to 'call_cache_fn' into
efi_enter_kernel(), which lives way at the end of head.S. In some cases,
the ARM version of the ADR instruction does not have sufficient range,
resulting in a build error:
arch/arm/boot/compressed/head.S:1453: Error: invalid constant (fffffffffffffbe4) after fixup
ARM defines an alternative with a wider range, called ADRL, but this does
not exist for Thumb-2. At the same time, the ADR instruction in Thumb-2
has a wider range, and so it does not suffer from the same issue.
So let's switch to ADRL for ARM builds, and keep the ADR for Thumb-2 builds.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200409130434.6736-6-ardb@kernel.org
This patch is to be squashed into 55c7c06210 ("ARM: dts: bcm283x: Fix
vc4's firmware bus DMA limitations") as it turned out to be faulty
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- First patch updates RPi4's expgpio's GPIO labels, adding the SD power rail.
- Second patch adds a fixed regulator that controls the SD power and
hooks it up with emmc2.
- Third patch rolls back to the firmware based power driver as the MMIO
version is unstable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
