Renesas ARM DT updates for v5.10 (take two)
- PCIe endpoint support for the RZ/G2H SoC,
- SATA support for the HopeRun HiHope RZ/G2H board,
- Increase support (CAN, LED, SPI NOR, VIN, VSP) for the RZ/G1H SoC on
the iWave Qseven board (G21D), and its camera add-on board,
- Initial support for the R-Car V3U SoC on the Falcon CPU and BreakOut
boards,
- HDMI display and sound support for the R-Car M3-W+ SoC on the
Salvator-XS board,
- Digital Radio Interface (DRIF) support for the R-Car E3 SoC,
- Minor fixes and cleanups.
* tag 'renesas-arm-dt-for-v5.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (24 commits)
arm64: dts: renesas: r8a774c0: Fix MSIOF1 DMA channels
arm64: dts: renesas: r8a77990: Fix MSIOF1 DMA channels
arm64: dts: renesas: r8a77990: Add DRIF support
ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add can0 support to camera DB
ARM: dts: r8a7742: Add VSP support
arm64: dts: renesas: Drop superfluous pin configuration containers
arm64: dts: renesas: r8a77961: salvator-xs: Add HDMI Sound support
arm64: dts: renesas: r8a77961: salvator-xs: Add HDMI Display support
arm64: dts: renesas: r8a77961: Add HDMI device nodes
arm64: dts: renesas: r8a77961: Add DU device nodes
arm64: dts: renesas: r8a77961: Add VSP device nodes
arm64: dts: renesas: r8a77961: Add FCP device nodes
arm64: dts: renesas: Fix pin controller node names
ARM: dts: renesas: Fix pin controller node names
arm64: dts: renesas: Add Renesas Falcon boards support
arm64: dts: renesas: Add Renesas R8A779A0 SoC support
ARM: dts: r8a7742-iwg21d-q7: Enable SD2 LED indication
ARM: dts: r8a7742-iwg21d-q7: Add can1 support to carrier board
ARM: dts: r8a7742-iwg21d-q7: Add SPI NOR support
ARM: dts: r8a7742: Add VIN DT nodes
...
Link: https://lore.kernel.org/r/20200918124800.15555-2-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
The Synopsys DesignWare APB GPIO controller driver does not parse
reg-io-width and dtschema does not allow it so drop it to fix dtschema
warnings like:
arch/arm/boot/dts/picoxcell-pc7302-pc3x2.dt.yaml: gpio@20000:
'reg-io-width' does not match any of the regexes: '^gpio-(port|controller)@[0-9a-f]+$', 'pinctrl-[0-9]+'
Link: https://lore.kernel.org/r/20200917164909.22490-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Ux500 DTS updates for the v5.10 kernel cycle:
- Add the s6e63m0 display to the Golden device
- Add the KTD253 backlight to the Skomer device
- Update the LP5521 LED DTS entries for binding changes
* tag 'ux500-dts-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ste-href: Add reg property to the LP5521 channel nodes
ARM: dts: ux500-skomer: Add KTD253 backlight
ARM: dts: ux500-golden: Add S6E63M0 DSI display
Link: https://lore.kernel.org/r/CACRpkda=-cgFjN7K2vBU5x4uSYrohrZSbjqMnSFb3Qe2Az1W5g@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: DT: Hisilicon ARM32 SoCs DT updates for 5.10
- Update the SP804 nodes to have the correct clocks and
clock names for the hi3620 SoC
- Update the SP805 nodes to have the correct clocks and
clock names for the hix5hd2 SoC
* tag 'hisi-arm32-dt-for-5.10' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: Fix SP805 clocks
ARM: dts: hisilicon: Fix SP804 users
Link: https://lore.kernel.org/r/5F617209.90003@hisilicon.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct the property for reset GPIOs of the GPIO expander.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PCA9539 GPIO expander requires GPIO controller properties to operate
properly.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All am437x boards have been converted to use new driver, so drop legacy
cpsw dt node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch all am437x boards to use new cpsw switch driver. Those boards
have or 2 Ext. port wired and configured in dual_mac mode by default, or
only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT node for the new cpsw switchdev based driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "eMMC high-speed DDR mode (3.3V I/O)" at 50MHz is supported on
the eMMC-interface of the lxa-mc1. Set it in the device tree to
benefit from the speed improvement.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Previously the FIFO on the stm32h743 usart was not utilized, because
the stm32f7 compatible configures it without FIFO support.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The stm32 spi driver tries to determine the fifo size of spi devices
dynamically. However, if the spi was already configured by the bootloader
the fifo size check can become an endless loop, because the driver
expects the spi to be in its initial "after device reset" state. The
driver does already support resetting the spi device at probe, thus this
patch adds only the required device tree properties
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
the desired phase shift between clock- and data-signal, now trigger a
kernel warning when used in rgmii-id mode:
*-skew-ps values should be used only with phy-mode = "rgmii"
This is because commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY") now configures own timings when
phy-mode = "rgmii-id". Device trees wanting to set their own delays
should use phy-mode "rgmii" instead as the warning prescribes.
The "standard" timings now used with "rgmii-id" work fine on this
board, so drop the explicit timings in the device tree and thereby
silence the warning.
Fixes: 666b5ca85c ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using the native SPI chipselect on i.MX6 is known to be problematic.
Doing it on a imx6q-sabresd causes the SPI NOR probe to fail:
[ 5.388704] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00
Use the GPIO chipselect to avoid such problem.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for imx6q-logicpd.dtb so that it can be built by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is standard practice to have a specific board compatible string, so
pass "logicpd,imx6q-logicpd".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix. While
touching the hogs, fix indentation (spaces -> tabs).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SMB347 is a battery charger controller which is found on the Nexus 7
device.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default parent for all MMCs is PLLP, which is running at 408 MHz on
Tegra30 and 50 MHz clock can't be derived from PLLP. The maximum SDIO
clock rate is 50 MHz, but this rate isn't achievable using PLLP.
Let's switch the WiFi MMC clock parent to PLLC in order to get true 50
MHz. This patch doesn't fix any problems, it's just a minor improvement.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default parent for all MMCs is PLLP, which is running at 216 MHz on
Tegra20 and 50 MHz clock can't be derived from PLLP. The maximum SDIO
clock rate is 50 MHz, but this rate isn't achievable using PLLP.
Let's switch the WiFi MMC clock parent to PLLC in order to get true 50
MHz. This patch doesn't fix any problems, it's just a minor improvement.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously 50MHz clock rate didn't work because of the wrong PINCTRL
configuration used for SDIO pins. Now the PINCTRL config is corrected
and the MMC clock rate could be bumped safely to 50MHz, increasing WiFi
TX throughput by 20 Mbit/s and allowing to hit the maximum 40 Mbit/s.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
