Booting 3.8-rc6 on omap4 panda results in the following error
[ 0.444427] omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 0.445770] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz
[ 0.473937] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 0.474670] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz
[ 0.474822] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 0.476379] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz
[ 0.477294] omap_i2c 48350000.i2c: did not get pins for i2c error: -19
[ 0.477996] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz
[ 0.483398] Switching to clocksource 32k_counter
This happens because omap4 panda dts file is not adapted to use i2c through
pinctrl framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap4460 panda with 3.8-rc6 kernel.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reported-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting 3.8-rc6 on omap 5430evm results in the following error
omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
This happens because omap5 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap5430 evm with 3.8-rc6 kernel.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the needed sections to enable audio support on Overo.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting 3.8-rc6 on omap 4430sdp results in the following error
omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
This happens because omap4 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap4430 sdp with 3.8-rc6 kernel.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Convert the on-board LED connected to the TWL4030 (LEDB) to use
pwm-leds.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Section to describe the backlight for the LCD panels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Sections to describe the pwm-leds in the system.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
We have proper driver stack to handle the pmu_stat LED which is connected
PWMB of twl4030.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Enable support for the PWMs and LED as PWM drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Enable support for the PWMs and LEDs as PWM drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a new address space/memory resource to d_can device tree node. D_CAN
RAM initialization is achieved through RAMINIT register which is part of
AM33XX control module address space. D_CAN RAM init or de-init should be
done by writing instance corresponding value to control module register.
Till we have a separate control module driver to write to control module,
d_can driver will handle the register writes to control module by itself.
So a new address space to represent this control module register is added
to d_can driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add d_can instances to aliases node to get the D_CAN instance number
from the driver. To initialize D_CAN message RAM, corresponding instance
number is required.
To initialize instance 0 message RAM then 0x1 should be written and for
instance 1 message RAM, 0x2 should be written to control module register.
With device-tree framework ip instance number is "-1" by default for all
instances. To get device id/instance number then modules should be added
to DT "aliases" node. of_alias_get_id() gives the device id number based
on number of alias nodes present in "aliases node".
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
This is a follow-up to Javier Martinez effort adding initial
device tree support to IGEP technology devices [1].
It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards.
[1] http://www.spinics.net/lists/linux-omap/msg83409.html
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ISEE IGEP COM Module is an TI OMAP3 SoC computer on module.
This patch adds an initial device tree support to boot an
IGEP COM Module from the MMC/SD.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[b-cousson@ti.com: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ISEE IGEPv2 is an TI OMAP3 SoC based embedded board.
This patch adds an initial device tree support to boot
an IGEPv2 from the MMC/SD.
Currently is working everything that is supported by DT
on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio).
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for USB host
pins.
CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Get rid of managing the PHY clock as it will be done by the PHY driver.
For that to work we create a clock alias that links the PHY clock name
to the PHY device name.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This helper allows board support code to add the PHY's
VCC and RESET regulators which are GPIO controlled as well
as the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3_noncore_dpll_set_rate() attempts an enable of bypass clk as well
as ref clk for every .set_rate attempt on a noncore DPLL, regardless of
whether the .set_rate results in the DPLL being locked or put in bypass.
Early at boot, while some of these DPLLs are programmed and locked
(using .set_rate for the DPLL), this causes an ordering issue.
For instance, on OMAP5, the USB DPLL derives its bypass clk from ABE DPLL.
If a .set_rate of USB DPLL which programmes the M,N and locks it is called
before the one for ABE, the enable of USB bypass clk (derived from ABE DPLL)
then attempts to lock the ABE DPLL and fails as the M,N values for ABE
are yet to be programmed.
To get rid of this ordering needs, enable bypass clk for a DPLL as part
of its .set_rate only when its being put in bypass, and only enable the
ref clk when its locked.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_pwrdm_save_clkdm_state_and_activate() tried to test one of its
unsigned arguments to determine whether it was less than zero. Fix by
moving the error test to the caller.
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod
framework. Just get rid of it, so we have one less flag to
worry about.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
WDT1 module can take one of the below clocks as input functional
clock -
- On-Chip 32K RC Osc [default/reset]
- 32K from PRCM
The On-Chip 32K RC Osc clock is not an accurate clock-source as per
the design/spec, so as a result, for example, timer which supposed
to get expired @60Sec, but will expire somewhere ~@40Sec, which is
not expected by any use-case.
The solution here is to switch the input clock-source to PRCM
generated 32K clock-source during boot-time itself.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn
makes sure that sysc idle bit-fields are configured to valid state on
enable/disable callbacks.
With the recent submitted patch from Santosh Shilimkar,
"ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc"
(commit: 4a98c2d89), it is required to add sysconf
information to each valid hwmod entry, else device will not be
come out from idle state properly and leads to below kernel
crash -
[2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at
0xf9e35034
[2.198325] Internal error: : 1028 [#1] SMP ARM
[2.203101] Modules linked in:
[2.206334] CPU: 0 Not tainted (3.9.0-rc3-00059-gd114294#1)
[2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60
[2.218090] LR is at omap_wdt_probe+0x184/0x1fc
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email address.
He submitted the patch earlier, but nobody felt responsible to pick
it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that
leads to unbootable kernels on all other machines and that needs
to depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F6UW
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add the lost dependency check for DEBUG_IMX_UART_PORT back
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRR/5HAAoJEFBXWFqHsHzOQxsH/2vXHYV3ds9HeBzb9UPIQEo5
dXKdUiSz/Sh/5gdm43swUOHr8nl3Wm0hqErGM1acyEBUcG9zDIJUMF5UX59tXCKs
uEFp/TufyDK1VCMwdkUrPZG9WNXnYZuAkAWv6plGZk+ZhHFYAUQccOH9TN8JE11E
IgmO2NTt9gG83dMF/jxsLQBGE0YcPWzdR34Uyfl4TUwq8w+MTUalWKpajn5pKkQ2
4rvqNRaXevlVRzKxYH5/Xpd0VeFZH1eK/wbWEQfc1jBXlGv52Fz3OTJWSOCi2z+y
FQ9DwShaHfHbhwJmM8pgWyHzUsd4iPuPxpsbtAIuM9yhOQkxxDLAshjCSjpJByI=
=lu20
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9-3' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 3:
- Add the lost dependency check for DEBUG_IMX_UART_PORT back
* tag 'imx-fixes-3.9-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull networking fixes from David Miller:
1) Fix ARM BPF JIT handling of negative 'k' values, from Chen Gang.
2) Insufficient space reserved for bridge netlink values, fix from
Stephen Hemminger.
3) Some dst_neigh_lookup*() callers don't interpret error pointer
correctly, fix from Zhouyi Zhou.
4) Fix transport match in SCTP active_path loops, from Xugeng Zhang.
5) Fix qeth driver handling of multi-order SKB frags, from Frank
Blaschka.
6) fec driver is missing napi_disable() call, resulting in crashes on
unload, from Georg Hofmann.
7) Don't try to handle PMTU events on a listening socket, fix from Eric
Dumazet.
8) Fix timestamp location calculations in IP option processing, from
David Ward.
9) FIB_TABLE_HASHSZ setting is not controlled by the correct kconfig
tests, from Denis V Lunev.
10) Fix TX descriptor push handling in SFC driver, from Ben Hutchings.
11) Fix isdn/hisax and tulip/de4x5 kconfig dependencies, from Arnd
Bergmann.
12) bnx2x statistics don't handle 4GB rollover correctly, fix from
Maciej Żenczykowski.
13) Openvswitch bug fixes for vport del/new error reporting, missing
genlmsg_end() call in netlink processing, and mis-parsing of
LLC/SNAP ethernet types. From Rich Lane.
14) SKB pfmemalloc state should only be propagated from the head page of
a compound page, fix from Pavel Emelyanov.
15) Fix link handling in tg3 driver for 5715 chips when autonegotation
is disabled. From Nithin Sujir.
16) Fix inverted test of cpdma_check_free_tx_desc return value in
davinci_emac driver, from Mugunthan V N.
17) vlan_depth is incorrectly calculated in skb_network_protocol(), from
Li RongQing.
18) Fix probing of Gobi 1K devices in qmi_wwan driver, and fix NCM
device mode backwards compat in cdc_ncm driver. From Bjørn Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
tcp: dont handle MTU reduction on LISTEN socket
bnx2x: fix occasional statistics off-by-4GB error
vhost/net: fix heads usage of ubuf_info
bridge: Add support for setting BR_ROOT_BLOCK flag.
bnx2x: add missing napi deletion in error path
drivers: net: ethernet: ti: davinci_emac: fix usage of cpdma_check_free_tx_desc()
ethernet/tulip: DE4x5 needs VIRT_TO_BUS
isdn: hisax: netjet requires VIRT_TO_BUS
net: cdc_ncm, cdc_mbim: allow user to prefer NCM for backwards compatibility
rtnetlink: Mask the rta_type when range checking
Revert "ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally"
Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug
smsc75xx: configuration help incorrectly mentions smsc95xx
net: fec: fix missing napi_disable call
net: fec: restart the FEC when PHY speed changes
skb: Propagate pfmemalloc on skb from head page only
...
While adding i.MX DEBUG_LL selection, commit f8c95fe (ARM: imx: support
DEBUG_LL uart port selection for all i.MX SoCs) leaves Kconfig symbol
DEBUG_IMX_UART_PORT there without any dependency check. This results in
that everyone gets the symbol in their config, which is someting
undesirable. Add "depends on ARCH_MXC" for the symbol to prevent that.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
