In order to use a device as interrupt controller, it needs to be marked
with the DT interrupt-controller property. This commit adds rudimentary
documentation about the required standard properties and describes the
most commonly used interrupt specifiers.
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
problems with JFFS2 usage, as the local bus (LPB) doesn't support
unaligned accesses as implemented in the JFFS2 code via memcpy().
By defining "no-unaligned-direct-access", the flash will not be
exposed directly to the MTD users (e.g. JFFS2) any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add OF support for the davinci nand controller.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add lis3lv02d device tree initialization code/API to take pdata from
device node. Also adds device tree init matching table support to
lis3lv02d_i2c driver. If the driver data is passed from device tree, then
this driver picks up platform data from device node through common/generic
lis3lv02d.c driver.
[akpm@linux-foundation.org: fix CONFIG_OF=n build]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds logic to parse lis3 properties from a device tree node and store them
in a freshly allocated lis3lv02d_platform_data.
Note that the actual match tables are left out here. This part should
happen in the drivers that bind to the individual busses (SPI/I2C/PCI).
Also adds some DT bindinds documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Rob Herring <robherring2@gmail.com>
Cc: "AnilKumar, Chimata" <anilkumar@ti.com>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "regulator: deprecate regulator-compatible DT property" deprecated
the use of the regulator-compatible DT property. Update the DT example in
the MAX8907 binding documentation to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit "regulator: deprecate regulator-compatible DT property" deprecated
the use of the regulator-compatible DT property. Update the DT example in
the TPS6586x binding documentation to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit "regulator: deprecate regulator-compatible DT property" deprecated
the use of the regulator-compatible DT property. Update the DT example in
the TPS65217 binding documentation to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the bindings for the TPS6586x regulator were being proposed, I
asserted that DT node naming rules for bus child nodes should also be
applied to nodes inside the TPS6586x regulator node itself. In other
words, that each node providing regulator init data should be named
after the type of object it represented ("regulator") and hence that
some other property was required to indicate which regulator the node
described ("regulator-compatible"). In turn this led to multiple nodes
having the same name, thus requiring node names to use a unit address
to make them unique, thus requiring reg properties within the nodes and
However, subsequent discussion indicates that the rules I was asserting
only applies to standardized bus nodes, and within a device's own node,
the binding can basically do anything sane that it wants.
Hence, this change deprecates the register-compatible property, and
instead uses node names to replace this functionality. This greatly
simplifies the device tree content, making them smaller and more legible.
The code is changed such that old device trees continue to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQVkutAAoJEHm+PkMAQRiGW8sH/36FVQ3zI75QH16AmR++2nMZ
BRJGoxcRFMssrXTYVdkMyzygf8b7MZbNEn1qt2g63MNzGaJucPlw5NVL4GLzR+zr
x/EglLrTEPCD5el9wJ3ls9iC1soudKQTvC2BjcdUjpoSwHrDM/7GKfbOacE54Wqc
C1VHCcg5DWOD7F0RnYT2SQEVCeDODNmcyFdk7Oi4cUicTPJoYWJ9O9MGfBDBok0N
M+dXxa9nvsl7EeEKpBKH9vo4TfXn3Gsj6LCRdedvI15ilZjfo8jdHYbSn7KBfQuZ
JIKRnqkaQ1JfMFt+M/JJZ1b/+Wrd4HLMmmn5oUmrGGIvhpi32nJfi/97+nSy8iU=
=c5gW
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc6' into spi-mxs
Linux 3.6-rc6
Conflicts (overlap between moving code that accesses registers around
and factoring the register access out into a SSP layer):
drivers/mmc/host/mxs-mmc.c
Even with devicetree support, we needed platform data to provide some data,
leading to mixed device tree and platform data. This patch makes it possible to
provide all that information via device tree. Now, the data must be provided
via platform data _or_ device tree completely.
Only in case of DMA where a callback specification is necessary (dma_filter()),
platform data is the only option.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
From Jason Cooper:
New drivers:
- pinctrl (dove, kirkwood, mvebu)
- gpio (mvebu)
* 'kirkwood/drivers' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add gpio support in defconfig
arm: mvebu: add DT information for GPIO banks on Armada 370 and XP
arm: mvebu: use GPIO support now that a driver is available
Documentation: add description of DT binding for the gpio-mvebu driver
gpio: introduce gpio-mvebu driver for Marvell SoCs
arm: mvebu: select the pinctrl drivers for Armada 370 and Armada XP platforms
arm: mvebu: split Kconfig options for Armada 370 and XP
ARM: mvebu: adjust Armada XP evaluation board DTS
ARM: mvebu: Add pinctrl support to Armada 370 SoC
ARM: mvebu: Add pinctrl support to Armada XP SoCs
pinctrl: mvebu: add pinctrl driver for Armada XP
pinctrl: mvebu: add pinctrl driver for Armada 370
pinctrl: mvebu: kirkwood pinctrl driver
pinctrl: mvebu: dove pinctrl driver
pinctrl: mvebu: pinctrl driver core
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
New bindings:
- iconnect nand and keys
- mv_cesa
- gpio-fan
* 'kirkwood/dt' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Use devicetree to define DNS-32[05] fan
hwmon: Add devicetree bindings to gpio-fan
Crypto: CESA: Add support for DT based instantiation.
ARM: Kirkwood: Describe iconnect nand in DT.
ARM: Kirkwood: Describe iconnect keys in DT.
Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Kirkwood SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Dove SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a pinctrl driver core for Marvell SoCs plus DT
binding documentation. This core driver will be used by SoC family
specific drivers, i.e. Armada XP, Armada 370, Dove, Kirkwood, aso.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/Kconfig
Allow a gpio-fan to be defined in devicetree, see binding documentation
for details.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on work by Michael Walle and Jason Cooper.
Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/mach-kirkwood/board-dt.c
Add device tree support to C_CAN/D_CAN controller and usage details
are added to device tree documentation. Driver was tested on AM335x
EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
For the of binding doc:
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.
Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
* next/soc: (50 commits)
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
ARM: tegra30: add CPU hotplug support
ARM: tegra: clean up the common assembly macros into sleep.h
ARM: tegra: replace the CPU CAR access code by tegra_cpu_car_ops
ARM: tegra: introduce tegra_cpu_car_ops structures
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: AM33XX: clock: Add dcan clock aliases for device-tree
ARM: OMAP2+: dpll: Add missing soc_is_am33xx() check for common functions
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
ARM: OMAP3+: hwmod: Add AM33XX HWMOD data
ARM: OMAP2+: hwmod: Hook-up am33xx support in omap_hwmod framework
...
Change/remove conflict in arch/arm/mach-ux500/clock.c resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC; enough to boot the system into an initrd with
UART console, interrupt controller, timers, and a stub clock driver.
Also provided is a similarly basic device tree for the Raspberry Pi
Model B board.
This series was written by Simon Arlott, Chris Boot, and Dom Cobley
downstream, with reference to a Broadcom tree, and modified for upstream
and submitted by Stephen Warren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQWnCOAAoJEJuNpwkmVCGcQS8P/01yZOE2QhW/S4ap1voLyRuI
T7wcjla6UXckuz72qnLitJCDHxwDAF6Kgc/anibQfgambqjOAA5YuXBkJlUaBQF1
3u6k8pNJ7cI3R44BznnLN4U8QXw/w5IlUdFu7Y7Xg4xyb1Fdx11QJelYmiPIdXEQ
fFVqO5JQoMWXz7i9fYU/jXHcbINyljgSqhBOM9O1R2W3kayPm3OdmyAXHzmt7rSw
XPta3QlrkI/fCgolI2A9LMhrfaJVRQe59H9b+fP2R9baWs7BnkZywjO8mwipR8eI
d4tRH8cy+Aa/RobLe5DnorxZ9abj3vlSv0kG0qBhcieqXZmGKlum3J4h1cBAvs8p
Cv0Gm7GFxeqCJ3RaLfn1mX2OESmGQ9KH33J3PFQUcNmd82saXz6Kas7YZ5KRlMAI
+TS3n9Er7P2HlpYF/3ckE3aYrN/iHJaZ/2pa2ZiR8KRnRTY3DMTxgvNIaz044zud
gHUbQpttzNV0aiqMDqMvpVqBhUMCVF0LWlhQyewQHHdVSS9XNq1lrfbXPc4k54Fs
Tkz4JT5S1Vhv+iqakwKQvNVpO8XWvj0Z5t5/3IqLpzdYWRp6kQh8giJXhLEQSoVl
38sJ2v6MzNmyx1yggO58Qq+OpelNDowhY0tGcOrSl6uR786gcivw9T2wd8V0iwbw
uMeZ6apUnOseOaKU9mrm
=vqsx
-----END PGP SIGNATURE-----
Merge tag 'rpi-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/soc
ARM: add basic BCM2835 SoC and Raspberry Pi board support
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC; enough to boot the system into an initrd with
UART console, interrupt controller, timers, and a stub clock driver.
Also provided is a similarly basic device tree for the Raspberry Pi
Model B board.
This series was written by Simon Arlott, Chris Boot, and Dom Cobley
downstream, with reference to a Broadcom tree, and modified for upstream
and submitted by Stephen Warren.
* tag 'rpi-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
From Kukjin Kim:
Here is G-Scaler DT for supporting EXYNOS5 SoCs.
* 'next/dt-gscaler' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
From Kukjin Kim:
This branch is for supporting pinctrl for Samsung EXYNOS. Now this can
support EXYNOS4210 and other EXYNOS SoCs such as EXYNOS4X12 will be
supported next time.
* 'next/pinctrl-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
gpio: exynos4: skip gpiolib registration if pinctrl driver is used
pinctrl: add exynos4210 specific extensions for samsung pinctrl driver
pinctrl: add samsung pinctrl and gpiolib driver
From Kukjin Kim:
Since there are many changes for gpio-samsung in my tree, this has been
included in my tree with Linus' agreement.
* 'next/gpio-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
gpio: samsung: add devicetree init for s3c24xx arches
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fzT6
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
Here we document the AB8500 Audio CODEC in the existing MFD AB8500 document.
CC: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the required documentation for the new Device Tree
bindings pertaining to the MSP CPU-side DAI Driver.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the required documentation for the new Device Tree
bindings pertaining to the MOP500 Audio Machine driver.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of having to duplicate the description of the properties needed
for interrupt support, reference the new standard document.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
[Minor spelling correction]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Timer peripheral provides four 32-bit timer channels and a
single 64-bit free running counter. Each channel has an output compare
register, which is compared against the 32 least significant bits of the
free running counter values, and generates an interrupt.
Timer 3 is used as the Linux timer.
The BCM2835 also contains an SP804-based timer module. However, it
apparently has significant differences from the standard SP804 IP block,
and Broadcom's documentation recommends using the system timer instead.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved to drivers/clocksource/. This looks like the desired location for
such code now.
* Added DT binding docs.
* Moved struct sys_timer bcm2835_timer into time.c to encapsulate it more.
* Simplified bcm2835_time_init() to find one matching node and operate on
it, rather than looping over all matching nodes. This seems more
consistent with other clocksource code.
* Simplified bcm2835_time_init() using of_iomap().
* Renamed struct bcm2835_timer.index to match_mask to better represent its
purpose.
* s/printk(PR_INFO/pr_info(/
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
the size of the hwirq space, and pass the total size of the hwirq space
to irq_domain_add_linear(), rather than just the number of valid hwirqs;
the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
rather than nesting it inside a /axi node. Hence, changed the reg value
since /axi had a ranges property. This seems simpler to me, but I'm not
sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
removing the need to patch include/linux/irqdomain.h or
kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC.
http://www.broadcom.com/products/BCM2835http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Note that the documentation in the latter .pdf assumes the MMU setup
that's used on the "VideoCore" companion processor, and does not document
physical peripheral addresses. Subtract 0x5e000000 to obtain the physical
addresses. This is accounted for by the ranges property in the /soc node
in the device tree.
The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a
minimal device tree for this board; enough to see some very early kernel
boot messages through earlyprintk. However, this patch does not yet
provide a useful booting system.
http://www.raspberrypi.org/.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split from 3-4 months ago, and significantly stripped down and
modified since.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add needed platform data structure and code to be able to load
the GPO child of twl6040.
Update the devicetree binding documentation at the same time.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "maxim,system-power-controller" to indicate whether the
PMIC is in charge of controlling the system power. If this is set, the
driver will provide the pm_power_off() function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This commit adds a driver for the Avionic Design N-bit GPIO expander.
The expander provides a variable number of GPIO pins with interrupt
support.
Changes in v2:
- allow building the driver as a module
- assign of_node unconditionally
- use linear mapping IRQ domain
- properly cleanup IRQ domain
- add OF device table and annotate device tables
- emulate rising and falling edge triggers
- increase #gpio-cells to 2
- drop support for !OF
- use IS_ENABLED to conditionalize DEBUG_FS code
Changes in v3:
- make IRQ support runtime configurable (interrupt-controller property)
- drop interrupt-controller and #interrupt-cells from DT binding
- add inline to_adnp() function to wrap container_of() macro
- consistently use adnp as name for struct adnp variables
- remove irq_mask_cur and rename irq_mask to irq_enable
- fix a subtle deadlock in adnp_gpio_direction_output()
- remove dynamic allocations from debugfs code
- rename regs to num_regs to avoid confusion
- annotate non-trivial code with comments
- don't acquire mutex in adnp_gpio_get()
- assume NO_IRQ == 0
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is initial device tree support for the ARM Integrator family,
we create a very basic device tree, #ifdef out the non-DT machines
when compiling for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds Device Tree probing support to the Versatile FPGA
IRQ controller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add regmap based syscon driver.
This is usually used for access misc bits in registers which does not belong
to a specific module, for example, IMX IOMUXC GPR and ANATOP.
With this driver, client can use generic regmap API to access registers
which are registered into syscon.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Converted to regmap-irq.
* Allowed probing from device tree.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> #v3
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UyqO
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
(The shortlog makes no sense here since it contains mostly the dependent
cleanups that are part of the preceding branches).
Signed-off-by: Olof Johansson <olof@lixom.net>
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6+9B
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull in a dependent branch from Mark Brown's regulator tree for the tegra/cleanup branch.
* depends/tps6589x-dt:
regulator: tps6586x: add support for SYS rail
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=KXPz
-----END PGP SIGNATURE-----
Merge tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/dt
From David Brown:
These patches migrate both the 8660 and 8960 targets on msm to be
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
By Stephen Boyd
via David Brown
* tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Remove non-DT targets from 8960
ARM: msm: Add DT support for 8960
ARM: msm: Move io mapping prototypes to common.h
ARM: msm: Rename board-msm8x60 to signify its DT only status
ARM: msm: Make 8660 a DT only target
ARM: msm: Move 8660 to DT timer
ARM: msm: Add DT support to msm_timer
ARM: msm: Allow timer.c to compile on multiple targets
ARM: msm: Don't touch GIC registers outside of GIC code
ARM: msm: Add msm8660-surf.dts to Makefile.boot
ARM: msm: Add handle_irq handler for 8660 DT machine
Resolved trivial context conflict in arch/arm/mach-msm/io.c and a
remove/change conflict in arch/arm/mach-msm/board-msm8x60.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
This pulls in the staging tree fixes in 3.6-rc6 into our branch to resolve the
merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GLSh
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparseirq-for-v3.7' into devel-dt
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
Conflicts:
arch/arm/mach-omap2/omap4-common.c
drivers/gpio/gpio-twl4030.c
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
IFM O2D cameras use special sensor bus interface glue-logic to
connect camera sensors to mpc5200 LocalPlus bus. Add device tree
bindings documentation for it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support to setup the MSM timer via information obtained from
the devicetree.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[davidb@codeaurora.org: Remove leading zeros]
Signed-off-by: David Brown <davidb@codeaurora.org>
With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It replaces the clk_register_clkdev in imx6q clock driver with DT
lookup. It depends on Mike's clk-3.7 branch.
When it gets merged together with imx-dt-3.7, there is a trivial
conflict on arch/arm/boot/dts/imx6q.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQTyFwAAoJEFBXWFqHsHzOcXkH/1a2RX8pUMsYHS5efpGaRUjJ
7PKKbAuMuGAgqdRDv1t2dcXuUv3zJgY/sdrivD9iwMqVSsQDW9MrdKyvBXg9m5UL
rg1Uc8r6mJlHSljimN8hoHp4PGFF7DCVls5y+3jsk/I2tWK+S/w00iP/aOFgkJNc
9Bg0ZhofKGOGpYK5joaBYAqvVM7F92gjpX+PytNEkJHGRKxCEsTRq4DRR3+r3uqs
GuoHOflYMEmviKYaZ/I14rwUJWFF4vIxuFC4vT88erpj3Fs0y7XkEWJiKU/2ma6M
w86qOUI6nU0iW5AILu3IvjSEvh2h/ZZ+5y3lVvzghcKK2QP4d4bEWnC745NRVSI=
=pxVx
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
It replaces the clk_register_clkdev in imx6q clock driver with DT
lookup. It depends on Mike's clk-3.7 branch.
* tag 'imx-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: replace clk_register_clkdev with clock DT lookup
Resolved context add/remove conflict in arch/arm/boot/dts/imx6q.dtsi
It replaces clk_register_clkdev in mxs clock driver with DT lookup.
The series depends on pull request mxs-dt-3.7 and Mike's clk branch
below.
git://git.linaro.org/people/mturquette/linux.git clk-3.7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQTvyZAAoJEFBXWFqHsHzO3kEIAKsT3i7vdriXVAityIMiC1el
pVDR2qVq0q7+MhCIO/wXWbjJBHK+vEiMY2sKWCD4jVfLCa751mwENAdf1h1/+NNZ
+W6uzRaMt3w4FGryn4/xXt4eVgZNNZba9NxE73tVSanK9oJilPwBLCCkwbZLFbjk
SughytSMml1uO8Z3mEG0DDmrCnwb1KsILasVLazTGA1gpQ02c+6ASPa8s0App6/2
DLkIOn6D3022LzQiIungxUc4wLBojylex/GCAPubyhX3pXyjlzUElp4G3AFex8KM
tMnuXBfpi1dLkgYPn+rkM8m48dCY821LxFT9OA3AfpzqVpRWU6Kcq60vNzUDnt0=
=scyJ
-----END PGP SIGNATURE-----
Merge tag 'mxs-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
It replaces clk_register_clkdev in mxs clock driver with DT lookup.
* tag 'mxs-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6:
clk: mxs: replace imx23 clk_register_clkdev with clock DT lookup
clk: mxs: replace imx28 clk_register_clkdev with clock DT lookup
SPEAr platforms now support DT and so must convert all drivers to support DT.
This patch adds DT probing support for Arasan Compact Flash controller and
updates its documentation too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.
Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
closer for being just a regular device driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A43b
-----END PGP SIGNATURE-----
mergetag object cf3a6ec2c0
type commit
tag cleanup-omap-tags-for-v3.7
tagger Tony Lindgren <tony@atomide.com> 1347323254 -0700
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=utuw
-----END PGP SIGNATURE-----
Merge tags 'omap-devel-gpmc-fixed-for-v3.7' and 'cleanup-omap-tags-for-v3.7' into cleanup-sparseirq
Changes for GPMC (General Purpose Memory Controller) that take it
closer for being just a regular device driver.
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
Freescale's Integrated Flash controller (IFC) may have one or two
interrupts. In case of single interrupt line, it will cover all IFC
interrupts.
Update this information in IFC device tree bindings
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i.MX usb controllers share non-core registers, which may include
SoC specific controls. We turn it into a usbmisc device and usbmisc
driver set operations needed by ci13xxx_imx driver.
For example, Sabrelite board has bad over-current design, we can
usbmisc to disable over-current detection.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the same time remove platform based support. No user for
this driver has made it into mainline so far, so all we break
is out of tree stuff.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
add of support for the davinci i2c driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[wsa: fix indentation in the binding description]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.
We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.
Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.
All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UHPu
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: musb: patches for v3.7 merge window
Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.
We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.
Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.
All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/qVp
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: xceiv: patches for v3.7 merge window
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It really becomes an maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx6q client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx23 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx28 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the Tobi/Overo board to the list of supported platforms.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
It adds a generic cpufreq driver for CPU0 frequency management based on
clk, regulator, OPP and device tree support. It can support both
uniprocessor (UP) and those symmetric multiprocessor (SMP) systems which
share clock and voltage across all CPUs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
With a lot of devices booting from device tree nowadays, it requires
that OPP table can be initialized from device tree. The patch adds
a helper function of_init_opp_table together with a binding doc for
that purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
