This is no longer needed as the device specific wake-up event
can now be specified with interrupts-extended property where
the second interrupt is the pinctrl-single register, such as
the UART3 RX pin.
Note that twl4030_omap3.dtsi needs to set WAKEUPENABLE for
off-idle to properly trigger the PMIC scripts. And GPIO pins
still need to set WAKEUPENABLE for wake-up events.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compared to legacy booting, we don't have wake-up events enabled
for device tree based booting. This means that if deeper idle
states are enabled, the device won't wake up to UART events and
seems like it has hung.
Let's fix that by adding the wake-up interrupt. Note that we
don't need to set the PIN_OFF_WAKEUPENABLE any longer, that's
handled by the wake-up interrupt when the serial driver does
request_irq on it.
Tested with the following on omap3-overo-summit that has the
ES2.1 omap:
#!/bin/bash
uarts=$(find /sys/class/tty/ttyO*/device/power/ -type d)
for uart in $uarts; do
echo 3000 > $uart/autosuspend_delay_ms
done
uarts=$(find /sys/class/tty/ttyO*/power/ -type d)
for uart in $uarts; do
echo enabled > $uart/wakeup
echo auto > $uart/control
done
echo 1 > /sys/kernel/debug/pm_debug/enable_off_mode
# grep -i uart /proc/interrupts
90: 1085 INTC 74 OMAP UART2
338: 5 pinctrl 366 OMAP UART2
# grep ^core_pwrdm /sys/kernel/debug/pm_debug/count
core_pwrdm (ON),OFF:1654,RET:131,INA:39,ON:1825...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that we can now use the CONFIG_GENERIC_CPUFREQ_CPU0,
so let's only enable that. Let's use CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND
as suggested by Nishant.
And also let's enable thermal as explained by Nishant Menon:
Many TI SoCs using Highest frequency is not really too nice of an idea for
long periods of time. And not everything is upstream to support things
optimially - example avs class 0, 1.5 ABB consolidation with cpufreq etc..
We definitely need thermal enabled as well for device safety needs.
[tony@atomide.com: updated per Nishant's suggestions]
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.
Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cc824534d4 ("ARM: OMAP2+: hwmod: Rearm wake-up interrupts
for DT when MUSB is idled") fixed issues with hung UART wake-up
events by calling _reconfigure_io_chain() when MUSB is connected
or disconnected.
As pointed out by Paul Walmsley, we may need to also call
_reconfigure_io_chain() in other cases, so it should be a separate
flag. Let's add HWMOD_RECONFIG_IO_CHAIN as suggested by Paul.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This switches the SAMA5D3 to use the new atmel,sama5d3-pinctrl id that was
added with the drive strength options patch.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: second compatible string kept as at91sam9x5]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SSC integrate in at91sam9g20 support frame sync length
extension, so switch compatible string to support this feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SSC integrate in at91sam9rl support frame sync length
extension, so switch compatible string to support this feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
We set the DMA configuration on USARTs in the SoC DT in (ARM: at91: sama5d3:
add usart dma configurations). As the audio must work with DMA channels, we
reserve some dma channels for audio, or else audio won't work.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: move to the sama5d3xmb.dtsi to cover all board variants]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
do_unexp_fiq() has never been called by any code in the last 10 years,
it's about time it was removed!
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces a new default FIQ handler that is structured in a
similar way to the existing ARM exception handler and result in the FIQ
being handled by C code running on the SVC stack (despite this code run
in the FIQ handler is subject to severe limitations with respect to
locking making normal interaction with the kernel impossible).
This default handler allows concepts that on x86 would be handled using
NMIs to be realized on ARM.
Credit:
This patch is a near complete re-write of a patch originally
provided by Anton Vorontsov. Today only a couple of small fragments
survive, however without Anton's work to build from this patch would
not exist. Thanks also to Russell King for spoonfeeding me a variety
of fixes during the review cycle.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds i2c pinctrl DT node for IFC6410 board. It also adds
necessary DT support for i2c eeprom which is present on IFC6410.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add support for i2c controller on the DB8074 board. It also adds necessary
DT support for i2c eeprom which is present on DB8074 board.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add a very minimalistic BCM63138 Device Tree include file which
describes the BCM63138 SoC with only the basic set of required
peripherals:
- Cortex A9 CPUs
- ARM GIC
- ARM SCU
- PL310 Level-2 cache controller
- ARM TWD & Global timers
- ARM TWD watchdog
- legacy MIPS bus (UBUS)
- BCM6345-style UARTs (disabled by default)
Since the PL310 L2 cache controller does not come out of reset with
correct default values, we need to override the 'cache-sets' and
'cache-size' properties to get its geometry right.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom BCM63xx DSL SoCs have a different UART implementation for which
we need specially crafted low-level debug assembly code to support. Add
support for this using the standard definitions provided in
include/linux/serial_bcm63xx.h (shared with their MIPS counterparts).
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds basic support for the Broadcom BCM63138 DSL SoC which is
using a dual-core Cortex A9 system. Add the very minimum required code
boot Linux on this SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable both PCIe ports, one of which is connected to an onboard ethernet
chip, whereas the other goes to a miniPCIe slot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, fixed PCIe supply property names in DT]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the PCIe controller device tree node and hook up the PCIe PHY from
the XUSB pad controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a Q8 format 7 inch tablet with an Allwinner A13 SoC.
It has 512MB DRAM, 4GB NAND flash, an accelerometer, camera,
RTL8188-based WiFi, and micro SD slot for external storage.
It is likely made by a subsidiary of Hanns.G (Hannstar).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most if not all boards we've seen have a fixed 5V regulator, which is
the main power supply and/or fixed output of the PMIC.
Add this one to the common regulators DTSI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The corresponding bug in pm-sh7372.c was fixed in commit
70fe7b2467 ("ARM: shmobile: Do not access sh7372 A4S domain
internals directly").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We are getting "PRM: I/O chain clock line assertion timed out" errors
on early omaps for device tree based booting. This is because we are
unconditionally calling reconfigure_io_chain while legacy booting
has omap3_has_io_chain_ctrl() checks in place in omap_hwmod.c.
For device tree based booting, we are calling reconfigure_io_chain
unconditionally from pinctrl framework. So we need to add a check for
omap3_has_io_chain_ctrl() to avoid the errors for trying to access
a register that does not exist.
For es3.0, the documentation in "4.11.2 Device Off-Mode Configuration"
just mentions PM_WKEN_WKUP[8] bit. For es3.1, there's a new chapter in
documentation for "4.11.2.2 I/O Wake-Up Mechanism" that describes the
PM_WKEN_WKUP[16] ST_IO_CHAIN bit. So PM_WKEN_WKUP[16] bit did not get
added until in es3.1 probaly to fix issues with flakey wake-up events.
We are doing proper checks for ST_IO_CHAIN already in id.c and with
omap3_has_io_chain_ctrl(). For more information, see also commit
b02b917211 ("ARM: OMAP3: PM: fix I/O wakeup and I/O chain clock
control detection").
Let's fix the issue by selecting the right function during init for
reconfigure_io_chain depending on the omap revision. For es3.0 and
earlier we need to just toggle EN_IO. By doing this, we can move the
check for omap3_has_io_chain_ctrl() from omap_hwmod.c to the init code
in prm_3xxx.c. And then we can unconditionally call reconfigure_io_chain.
Thanks to Paul Walmsley and Nishanth Menon for help with debugging the
issue.
Fixes: 30a69ef785 ("ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just move the code over as it has no dependencies
on arch/arm/ anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP INTC irqchip driver will be moved under
drivers/irqchip/ soon but we still have a dependency
with mach-omap2 when it comes to idle functions.
In order to make it easy to share those function
prototypes with OMAP PM code, we introduce this new
header.
To avoid modifying several board-files and some of
the PM-related code, we just include the new header
from common.h which was already included by all
users of IRQ-related PM code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By moving i2c devices to DT we can clean up
i2c_board_info and fix a problem with moving
INTC to irq domain where IRQs can be renumbered
on each boot.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a copy'n'paste error making the rk3188 emmc pinctrl nodes reference
the pcfg_pull_default setting that is not available on rk3188.
Reported-by: Naoki FUKAUMI <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The host and otg regulator pinctrl settings got swapped, making the host
reference the otg pinctrl and the other way round. The actual pins are
correct (gpio0-3 for host and gpio2-31 for otg).
Reported-by: Naoki FUKAUMI <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
remove all the board files soon, we can remove this one without problem.
If you use this board, please use a DT-enabled at91sam9g20 kernel with
at91-foxg20.dts.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Sergio Tanzilli <tanzilli@acmesystems.it>
This defconfig already enables DEBUG_LL and by default DEBUG_LL_UART_NONE
will be selected (but due to some back compability magic I'd like to
remove is not actually honoured). DEBUG_LL_UART_PL01X is a much saner
default.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This defconfig already enables DEBUG_LL and by default DEBUG_LL_UART_NONE
will be selected (but due to some back compability magic I'd like to
remove is not actually honoured). DEBUG_LL_UART_PL01X is a much saner
default.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Clark reports a sleeping while atomic bug when using perf.
BUG: sleeping function called from invalid context at ../kernel/locking/mutex.c:583
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
------------[ cut here ]------------
WARNING: CPU: 2 PID: 4828 at ../kernel/locking/mutex.c:479 mutex_lock_nested+0x3a0/0x3e8()
DEBUG_LOCKS_WARN_ON(in_interrupt())
Modules linked in:
CPU: 2 PID: 4828 Comm: Xorg.bin Tainted: G W 3.17.0-rc3-00234-gd535c45-dirty #819
[<c0216690>] (unwind_backtrace) from [<c0212174>] (show_stack+0x10/0x14)
[<c0212174>] (show_stack) from [<c0867cc0>] (dump_stack+0x98/0xb8)
[<c0867cc0>] (dump_stack) from [<c02492a4>] (warn_slowpath_common+0x70/0x8c)
[<c02492a4>] (warn_slowpath_common) from [<c02492f0>] (warn_slowpath_fmt+0x30/0x40)
[<c02492f0>] (warn_slowpath_fmt) from [<c086a3f8>] (mutex_lock_nested+0x3a0/0x3e8)
[<c086a3f8>] (mutex_lock_nested) from [<c0294d08>] (irq_find_host+0x20/0x9c)
[<c0294d08>] (irq_find_host) from [<c0769d50>] (of_irq_get+0x28/0x48)
[<c0769d50>] (of_irq_get) from [<c057d104>] (platform_get_irq+0x1c/0x8c)
[<c057d104>] (platform_get_irq) from [<c021a06c>] (cpu_pmu_enable_percpu_irq+0x14/0x38)
[<c021a06c>] (cpu_pmu_enable_percpu_irq) from [<c02b1634>] (flush_smp_call_function_queue+0x88/0x178)
[<c02b1634>] (flush_smp_call_function_queue) from [<c0214dc0>] (handle_IPI+0x88/0x160)
[<c0214dc0>] (handle_IPI) from [<c0208930>] (gic_handle_irq+0x64/0x68)
[<c0208930>] (gic_handle_irq) from [<c0212d04>] (__irq_svc+0x44/0x5c)
Exception stack(0xe63ddea0 to 0xe63ddee8)
dea0: 00000001 00000001 00000000 c2f3b200 c16db380 c032d4a0 e63ddf40 60010013
dec0: 00000000 001fbfd4 00000100 00000000 00000001 e63ddee8 c0284770 c02a2e30
dee0: 20010013 ffffffff
[<c0212d04>] (__irq_svc) from [<c02a2e30>] (ktime_get_ts64+0x1c8/0x200)
[<c02a2e30>] (ktime_get_ts64) from [<c032d4a0>] (poll_select_set_timeout+0x60/0xa8)
[<c032d4a0>] (poll_select_set_timeout) from [<c032df64>] (SyS_select+0xa8/0x118)
[<c032df64>] (SyS_select) from [<c020e8e0>] (ret_fast_syscall+0x0/0x48)
---[ end trace 0bb583b46342da6f ]---
INFO: lockdep is turned off.
We don't really need to get the platform irq again when we're
enabling or disabling the per-cpu irq. Furthermore, we don't
really need to set and clear bits in the active_irqs bitmask
because that's only used in the non-percpu irq case to figure out
when the last CPU PMU has been disabled. Just pass the irq
directly to the enable/disable functions to clean all this up.
This should be slightly more efficient and also fix the
scheduling while atomic bug.
Fixes: bbd6455937 "ARM: perf: support percpu irqs for the CPU PMU"
Reported-by: Rob Clark <robdclark@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked. TPIDRURO in
particular needs careful treatment. Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.
Similarly, TEEHBR needs to be cleared during exec as well. Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs. Just
setting the register directly is sufficient.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previous commits that dealt with get_user for 64bit type missed to
export proper functions, so if get_user macro with particular target/value
types are used by kernel module modpost would produce 'undefined!' error.
Solution is to export all required functions.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AUX setting has no effect that's why remove it.
Warning log:
L2C: platform provided aux values match the hardware, so
have no effect. Please remove them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Match the naming pattern of all other SMP ops and rename
zynq_platform_cpu_die --> zynq_cpu_die.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The hotplug code contains only a single function, which is an SMP
function. Move that to platsmp.c where all other SMP runctions reside.
That allows removing hotplug.c and declaring the cpu_die function
static.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Avoid races and add synchronisation between the arch specific
kill and die routines.
The same synchronisation issue was fixed on IMX platform
by this commit:
"ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill"
(sha1: 2f3edfd7e2)
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As there is no Power management unit on this board, it is not possible to power
down a core, just WFI is allowed. There is no point to invalidate the cache and
exit coherency.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DDR controller can detect idle periods and leverage low power
features clock stop. When new requests occur, the DDRC resumes
normal operation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
