The basic problem description is as follows:
Be there 3 switches in a daisy chain topology:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
The CPU will not be able to ping through the user ports of the
bottom-most switch (like for example sw2p0), simply because tag_8021q
was not coded up for this scenario - it has always assumed DSA switch
trees with a single switch.
To add support for the topology above, we must admit that the RX VLAN of
sw2p0 must be added on some ports of switches 0 and 1 as well. This is
in fact a textbook example of thing that can use the cross-chip notifier
framework that DSA has set up in switch.c.
There is only one problem: core DSA (switch.c) is not able right now to
make the connection between a struct dsa_switch *ds and a struct
dsa_8021q_context *ctx. Right now, it is drivers who call into
tag_8021q.c and always provide a struct dsa_8021q_context *ctx pointer,
and tag_8021q.c calls them back with the .tag_8021q_vlan_{add,del}
methods.
But with cross-chip notifiers, it is possible for tag_8021q to call
drivers without drivers having ever asked for anything. A good example
is right above: when sw2p0 wants to set itself up for tag_8021q,
the .tag_8021q_vlan_add method needs to be called for switches 1 and 0,
so that they transport sw2p0's VLANs towards the CPU without dropping
them.
So instead of letting drivers manage the tag_8021q context, add a
tag_8021q_ctx pointer inside of struct dsa_switch, which will be
populated when dsa_tag_8021q_register() returns success.
The patch is fairly long-winded because we are partly reverting commit
5899ee367a ("net: dsa: tag_8021q: add a context structure") which made
the driver-facing tag_8021q API use "ctx" instead of "ds". Now that we
can access "ctx" directly from "ds", this is no longer needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming patches will add tag_8021q related logic to switch.c and
port.c, in order to allow it to make use of cross-chip notifiers.
In addition, a struct dsa_8021q_context *ctx pointer will be added to
struct dsa_switch.
It seems fairly low-reward to #ifdef the *ctx from struct dsa_switch and
to provide shim implementations of the entire tag_8021q.c calling
surface (not even clear what to do about the tag_8021q cross-chip
notifiers to avoid compiling them). The runtime overhead for switches
which don't use tag_8021q is fairly small because all helpers will check
for ds->tag_8021q_ctx being a NULL pointer and stop there.
So let's make it part of dsa_core.o.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of moving tag_8021q to core DSA, move all initialization
and teardown related to tag_8021q which is currently done by drivers in
2 functions called "register" and "unregister". These will gather more
functionality in future patches, which will better justify the chosen
naming scheme.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pe to give the user a string holding the error code instead of just
a number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the tag_8021q code has been taken out of sja1105, which uses
"rc" for its return code variables, whereas the DSA core uses "err".
Change tag_8021q for consistency.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply put, the best-effort VLAN filtering mode relied on VLAN retagging
from a bridge VLAN towards a tag_8021q sub-VLAN in order to be able to
decode the source port in the tagger, but the VLAN retagging
implementation inside the sja1105 chips is not the best and we were
relying on marginal operating conditions.
The most notable limitation of the best-effort VLAN filtering mode is
its incapacity to treat this case properly:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp4 master br0
bridge vlan del dev swp4 vid 1
bridge vlan add dev swp4 vid 1 pvid
When sending an untagged packet through swp2, the expectation is for it
to be forwarded to swp4 as egress-tagged (so it will contain VLAN ID 1
on egress). But the switch will send it as egress-untagged.
There was an attempt to fix this here:
https://patchwork.kernel.org/project/netdevbpf/patch/20210407201452.1703261-2-olteanv@gmail.com/
but it failed miserably because it broke PTP RX timestamping, in a way
that cannot be corrected due to hardware issues related to VLAN
retagging.
So with either PTP broken or pushing VLAN headers on egress for untagged
packets being broken, the sad reality is that the best-effort VLAN
filtering code is broken. Delete it.
Note that this means there will be a temporary loss of functionality in
this driver until it is replaced with something better (network stack
RX/TX capability for "mode 2" as described in
Documentation/networking/dsa/sja1105.rst, the "port under VLAN-aware
bridge" case). We simply cannot keep this code until that driver rework
is done, it is super bloated and tangled with tag_8021q.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was not caught because there is no switch driver which implements
the .port_bridge_join but not .port_bridge_leave method, but it should
nonetheless be fixed, as in certain conditions (driver development) it
might lead to NULL pointer dereference.
Fixes: f66a6a69f9 ("net: dsa: permit cross-chip bridging between all trees in the system")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core has a layered structure, and even though we end up
returning 0 (success) to user space when setting a bonding/team upper
that can't be offloaded, some parts of the framework actually need to
know that we couldn't offload that.
For example, if dsa_switch_lag_join returns 0 as it currently does,
dsa_port_lag_join has no way to tell a successful offload from a
software fallback, and it will call dsa_port_bridge_join afterwards.
Then we'll think we're offloading the bridge master of the LAG, when in
fact we're not even offloading the LAG. In turn, this will make us set
skb->offload_fwd_mark = true, which is incorrect and the bridge doesn't
like it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we join a bridge that already has some local addresses pointing to
itself, we do not get those notifications. Similarly, when we leave that
bridge, we do not get notifications for the deletion of those entries.
The only switchdev notifications we get are those of entries added while
the DSA port is enslaved to the bridge.
This makes use cases such as the following work properly (with the
number of additions and removals properly balanced):
ip link add br0 type bridge
ip link add br1 type bridge
ip link set br0 address 00:01:02:03:04:05
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 up
ip link set swp1 up
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 up
ip link set br1 up
ip link del br1 # 00:01:02:03:04:05 still installed on the CPU port
ip link del br0 # 00:01:02:03:04:05 finally removed from the CPU port
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When
(a) "dev" is a bridge port which the DSA switch tree offloads, but is
otherwise not a dsa slave (such as a LAG netdev), or
(b) "dev" is the bridge net device itself
then strange things happen to the dev_hold/dev_put pair:
dsa_schedule_work() will still be called with a DSA port that offloads
that netdev, but dev_hold() will be called on the non-DSA netdev.
Then the "if" condition in dsa_slave_switchdev_event_work() does not
pass, because "dev" is not a DSA netdev, so dev_put() is not called.
This results in the simple fact that we have a reference counting
mismatch on the "dev" net device.
This can be seen when we add support for host addresses installed on the
bridge net device.
ip link add br1 type bridge
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 master br1
ip link del br1
[ 968.512278] unregister_netdevice: waiting for br1 to become free. Usage count = 5
It seems foolish to do penny pinching and not add the net_device pointer
in the dsa_switchdev_event_work structure, so let's finally do that.
As an added bonus, when we start offloading local entries pointing
towards the bridge, these will now properly appear as 'offloaded' in
'bridge fdb' (this was not possible before, because 'dev' was assumed to
only be a DSA net device):
00:01:02:03:04:05 dev br0 vlan 1 offload master br0 permanent
00:01:02:03:04:05 dev br0 offload master br0 permanent
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge supports a legacy way of adding local (non-forwarded) FDB
entries, which works on an individual port basis:
bridge fdb add dev swp0 00:01:02:03:04:05 master local
As well as a new way, added by Roopa Prabhu in commit 3741873b4f
("bridge: allow adding of fdb entries pointing to the bridge device"):
bridge fdb add dev br0 00:01:02:03:04:05 self local
The two commands are functionally equivalent, except that the first one
produces an entry with fdb->dst == swp0, and the other an entry with
fdb->dst == NULL. The confusing part, though, is that even if fdb->dst
is swp0 for the 'local on port' entry, that destination is not used.
Nonetheless, the idea is that the bridge has reference counting for
local entries, and local entries pointing towards the bridge are still
'as local' as local entries for a port.
The bridge adds the MAC addresses of the interfaces automatically as
FDB entries with is_local=1. For the MAC address of the ports, fdb->dst
will be equal to the port, and for the MAC address of the bridge,
fdb->dst will point towards the bridge (i.e. be NULL). Therefore, if the
MAC address of the bridge is not inherited from either of the physical
ports, then we must explicitly catch local FDB entries emitted towards
the br0, otherwise we'll miss the MAC address of the bridge (and, of
course, any entry with 'bridge add dev br0 ... self local').
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge automatically creates local (not forwarded) fdb entries
pointing towards physical ports with their interface MAC addresses.
For switchdev, the significance of these fdb entries is the exact
opposite of that of non-local entries: instead of sending these frame
outwards, we must send them inwards (towards the host).
NOTE: The bridge's own MAC address is also "local". If that address is
not shared with any port, the bridge's MAC is not be added by this
functionality - but the following commit takes care of that case.
NOTE 2: We mark these addresses as host-filtered regardless of the value
of ds->assisted_learning_on_cpu_port. This is because, as opposed to the
speculative logic done for dynamic address learning on foreign
interfaces, the local FDB entries are rather fixed, so there isn't any
risk of them migrating from one bridge port to another.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is able to install FDB entries towards the CPU port for addresses
which were dynamically learnt by the software bridge on foreign
interfaces that are in the same bridge with a DSA switch interface.
Since this behavior is opportunistic, it is guarded by the
"assisted_learning_on_cpu_port" property which can be enabled by drivers
and is not done automatically (since certain switches may support
address learning of packets coming from the CPU port).
But if those FDB entries added on the foreign interfaces are static
(added by the user) instead of dynamically learnt, currently DSA does
not do anything (and arguably it should).
Because static FDB entries are not supposed to move on their own, there
is no downside in reusing the "assisted_learning_on_cpu_port" logic to
sync static FDB entries to the DSA CPU port unconditionally, even if
assisted_learning_on_cpu_port is not requested by the driver.
For example, this situation:
br0
/ \
swp0 dummy0
$ bridge fdb add 02:00:de:ad:00:01 dev dummy0 vlan 1 master static
Results in DSA adding an entry in the hardware FDB, pointing this
address towards the CPU port.
The same is true for entries added to the bridge itself, e.g:
$ bridge fdb add 02:00:de:ad:00:01 dev br0 vlan 1 self local
(except that right now, DSA still ignores 'local' FDB entries, this will
be changed in a later patch)
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DSA master implements strict address filtering, then the unicast
and multicast addresses kept by the DSA CPU ports should be synchronized
with the address lists of the DSA master.
Note that we want the synchronization of the master's address lists even
if the DSA switch doesn't support unicast/multicast database operations,
on the premises that the packets will be flooded to the CPU in that
case, and we should still instruct the master to receive them. This is
why we do the dev_uc_add() etc first, even if dsa_port_notify() returns
-EOPNOTSUPP. In turn, dev_uc_add() and friends return error only if
memory allocation fails, so it is probably ok to check and propagate
that error code and not just ignore it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same concerns expressed for host MDB entries are valid for host FDBs
just as well:
- in the case of multiple bridges spanning the same switch chip, deleting
a host FDB entry that belongs to one bridge will result in breakage to
the other bridge
- not deleting FDB entries across DSA links means that the switch's
hardware tables will eventually run out, given enough wear&tear
So do the same thing and introduce reference counting for CPU ports and
DSA links using the same data structures as we have for MDB entries.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA treats some bridge FDB entries by trapping them to the CPU port.
Currently, the only class of such entries are FDB addresses learnt by
the software bridge on a foreign interface. However there are many more
to be added:
- FDB entries with the is_local flag (for termination) added by the
bridge on the user ports (typically containing the MAC address of the
bridge port)
- FDB entries pointing towards the bridge net device (for termination).
Typically these contain the MAC address of the bridge net device.
- Static FDB entries installed on a foreign interface that is in the
same bridge with a DSA user port.
The reason why a separate cross-chip notifier for host FDBs is justified
compared to normal FDBs is the same as in the case of host MDBs: the
cross-chip notifier matching function in switch.c should avoid
installing these entries on routing ports that route towards the
targeted switch, but not towards the CPU. This is required in order to
have proper support for H-like multi-chip topologies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since the cross-chip notifiers were introduced, the design was
meant to be simplistic and just get the job done without worrying too
much about dangling resources left behind.
For example, somebody installs an MDB entry on sw0p0 in this daisy chain
topology. It gets installed using ds->ops->port_mdb_add() on sw0p0,
sw1p4 and sw2p4.
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Then the same person deletes that MDB entry. The cross-chip notifier for
deletion only matches sw0p0:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
Why?
Because the DSA links are 'trunk' ports, if we just go ahead and delete
the MDB from sw1p4 and sw2p4 directly, we might delete those multicast
entries when they are still needed. Just consider the fact that somebody
does:
- add a multicast MAC address towards sw0p0 [ via the cross-chip
notifiers it gets installed on the DSA links too ]
- add the same multicast MAC address towards sw0p1 (another port of that
same switch)
- delete the same multicast MAC address from sw0p0.
At this point, if we deleted the MAC address from the DSA links, it
would be flooded, even though there is still an entry on switch 0 which
needs it not to.
So that is why deletions only match the targeted source port and nothing
on DSA links. Of course, dangling resources means that the hardware
tables will eventually run out given enough additions/removals, but hey,
at least it's simple.
But there is a bigger concern which needs to be addressed, and that is
our support for SWITCHDEV_OBJ_ID_HOST_MDB. DSA simply translates such an
object into a dsa_port_host_mdb_add() which ends up as ds->ops->port_mdb_add()
on the upstream port, and a similar thing happens on deletion:
dsa_port_host_mdb_del() will trigger ds->ops->port_mdb_del() on the
upstream port.
When there are 2 VLAN-unaware bridges spanning the same switch (which is
a use case DSA proudly supports), each bridge will install its own
SWITCHDEV_OBJ_ID_HOST_MDB entries. But upon deletion, DSA goes ahead and
emits a DSA_NOTIFIER_MDB_DEL for dp->cpu_dp, which is shared between the
user ports enslaved to br0 and the user ports enslaved to br1. Not good.
The host-trapped multicast addresses installed by br1 will be deleted
when any state changes in br0 (IGMP timers expire, or ports leave, etc).
To avoid this, we could of course go the route of the zero-sum game and
delete the DSA_NOTIFIER_MDB_DEL call for dp->cpu_dp. But the better
design is to just admit that on shared ports like DSA links and CPU
ports, we should be reference counting calls, even if this consumes some
dynamic memory which DSA has traditionally avoided. On the flip side,
the hardware tables of switches are limited in size, so it would be good
if the OS managed them properly instead of having them eventually
overflow.
To address the memory usage concern, we only apply the refcounting of
MDB entries on ports that are really shared (CPU ports and DSA links)
and not on user ports. In a typical single-switch setup, this means only
the CPU port (and the host MDB entries are not that many, really).
The name of the newly introduced data structures (dsa_mac_addr) is
chosen in such a way that will be reusable for host FDB entries (next
patch).
With this change, we can finally have the same matching logic for the
MDB additions and deletions, as well as for their host-trapped variants.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit abd49535c3 ("net: dsa: execute dsa_switch_mdb_add only for
routing port in cross-chip topologies") does a surprisingly good job
even for the SWITCHDEV_OBJ_ID_HOST_MDB use case, where DSA simply
translates a switchdev object received on dp into a cross-chip notifier
for dp->cpu_dp.
To visualize how that works, imagine the daisy chain topology below and
consider a SWITCHDEV_OBJ_ID_HOST_MDB object emitted on sw2p0. How does
the cross-chip notifier know to match on all the right ports (sw0p4, the
dedicated CPU port, sw1p4, an upstream DSA link, and sw2p4, another
upstream DSA link)?
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
The answer is simple: the dedicated CPU port of sw2p0 is sw0p4, and
dsa_routing_port returns the upstream port for all switches.
That is fine, but there are other topologies where this does not work as
well. There are trees with "H" topologies in the wild, where there are 2
or more switches with DSA links between them, but every switch has its
dedicated CPU port. For these topologies, it seems stupid for the neighbor
switches to install an MDB entry on the routing port, since these
multicast addresses are fundamentally different than the usual ones we
support (and that is the justification for this patch, to introduce the
concept of a termination plane multicast MAC address, as opposed to a
forwarding plane multicast MAC address).
For example, when a SWITCHDEV_OBJ_ID_HOST_MDB would get added to sw0p0,
without this patch, it would get treated as a regular port MDB on sw0p2
and it would match on the ports below (including the sw1p3 routing port).
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ x ] [ ] [ ] [ ]
With the patch, the host MDB notifier on sw0p0 matches only on the local
switch, which is what we want for a termination plane address.
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ ] [ ] [ ] [ ]
Name this new matching function "dsa_switch_host_address_match" since we
will be reusing it soon for host FDB entries as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add reference counting for FDB entries in cross-chip
topologies, and in order for that to have any chance of working and not
be unbalanced (leading to entries which are never deleted), we need to
ensure that higher layers are sane, because if they aren't, it's garbage
in, garbage out.
For example, if we add a bridge FDB entry twice, the bridge properly
errors out:
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
RTNETLINK answers: File exists
However, the same thing cannot be said about the bridge bypass
operations:
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ echo $?
0
But one 'bridge fdb del' is enough to remove the entry, no matter how
many times it was added.
The bridge bypass operations are impossible to maintain in these
circumstances and lack of support for reference counting the cross-chip
notifiers is holding us back from making further progress, so just drop
support for them. The only way left for users to install static bridge
FDB entries is the proper one, using the "master static" flags.
With this change, rtnl_fdb_add() falls back to calling
ndo_dflt_fdb_add() which uses the duplicate-exclusive variant of
dev_uc_add(): dev_uc_add_excl(). Because DSA does not (yet) declare
IFF_UNICAST_FLT, this results in us going to promiscuous mode:
$ bridge fdb add dev swp0 00:01:02:03:04:05
[ 28.206743] device swp0 entered promiscuous mode
$ bridge fdb add dev swp0 00:01:02:03:04:05
RTNETLINK answers: File exists
So even if it does not completely fail, there is at least some indication
that it is behaving differently from before, and closer to user space
expectations, I would argue (the lack of a "local|static" specifier
defaults to "local", or "host-only", so dev_uc_add() is a reasonable
default implementation). If the generic implementation of .ndo_fdb_add
provided by Vlad Yasevich is a proof of anything, it only proves that
the implementation provided by DSA was always wrong, by not looking at
"ndm->ndm_state & NUD_NOARP" (the "static" flag which means that the FDB
entry points outwards) and "ndm->ndm_state & NUD_PERMANENT" (the "local"
flag which means that the FDB entry points towards the host). It all
used to mean the same thing to DSA.
Update the documentation so that the users are not confused about what's
going on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch port leaves a bonding interface that is under a
bridge, there might be dangling switchdev objects on that port left
behind, because the bridge is not aware that its lower interface (the
bond) changed state in any way.
Call the bridge replay helpers with adding=false before changing
dp->bridge_dev to NULL, because we need to simulate to
dsa_slave_port_obj_del() that these notifications were emitted by the
bridge.
We add this hook to the NETDEV_PRECHANGEUPPER event handler, because
we are calling into switchdev (and the __switchdev_handle_port_obj_del
fanout helpers expect the upper/lower adjacency lists to still be valid)
and PRECHANGEUPPER is the last moment in time when they still are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to add more logic to the DSA NETDEV_PRECHANGEUPPER event
handler, more exactly we need to request an unsync of switchdev objects.
In order to fit more code, refactor the existing logic into a helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switchdev port leaves a LAG that is a bridge port, the switchdev
objects and port attributes offloaded to that port are not removed:
ip link add br0 type bridge
ip link add bond0 type bond mode 802.3ad
ip link set swp0 master bond0
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 nomaster
VLAN 100 will remain installed on swp0 despite it going into standalone
mode, because as far as the bridge is concerned, nothing ever happened
to its bridge port.
Let's extend the bridge vlan, fdb and mdb replay functions to take a
'bool adding' argument, and make DSA and ocelot call the replay
functions with 'adding' as false from the switchdev unsync path, for the
switch port that leaves the bridge.
Note that this patch in itself does not salvage anything, because in the
current pull mode of operation, DSA still needs to call the replay
helpers with adding=false. This will be done in another patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a slight inconvenience in the switchdev replay helpers added
recently, and this is when:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 master bond0
ip link set swp1 master bond0
Since the underlying driver (currently only DSA) asks for a replay of
VLANs when swp0 and swp1 join the LAG because it is bridged, what will
happen is that DSA will try to react twice on the VLAN event for swp0.
This is not really a huge problem right now, because most drivers accept
duplicates since the bridge itself does, but it will become a problem
when we add support for replaying switchdev object deletions.
Let's fix this by adding a blank void *ctx in the replay helpers, which
will be passed on by the bridge in the switchdev notifications. If the
context is NULL, everything is the same as before. But if the context is
populated with a valid pointer, the underlying switchdev driver
(currently DSA) can use the pointer to 'see through' the bridge port
(which in the example above is bond0) and 'know' that the event is only
for a particular physical port offloading that bridge port, and not for
all of them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the driver asks for a replay of a certain type of
event (port object or attribute) for a bridge port that is a LAG, it may
do so because this port has just joined the LAG.
But there might already be other switchdev ports in that LAG, and it is
preferable that those preexisting switchdev ports do not act upon the
replayed event.
The solution is to add a context to switchdev events, which is NULL most
of the time (when the bridge layer initiates the call) but which can be
set to a value controlled by the switchdev driver when a replay is
requested. The driver can then check the context to figure out if all
ports within the LAG should act upon the switchdev event, or just the
ones that match the context.
We have to modify all switchdev_handle_* helper functions as well as the
prototypes in the drivers that use these helpers too, because these
helpers hide the underlying struct switchdev_notifier_info from us and
there is no way to retrieve the context otherwise.
The context structure will be populated and used in later patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MRP hardware assist being supported only by the ocelot switch
family, which by design does not support cross-chip bridging, the
current match functions are at best a guess and have not been confirmed
in any way to do anything relevant in a multi-switch topology.
Drop the code and make the notifiers match only on the targeted switch
port.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_change_mtu() calls dsa_port_mtu_change() twice:
- it sends a cross-chip notifier with the MTU of the CPU port which is
used to update the DSA links.
- it sends one targeted MTU notifier which is supposed to only match the
user port on which we are changing the MTU. The "propagate_upstream"
variable is used here to bypass the cross-chip notifier system from
switch.c
But due to a mistake, the second, targeted notifier matches not only on
the user port, but also on the DSA link which is a member of the same
switch, if that exists.
And because the DSA links of the entire dst were programmed in a
previous round to the largest_mtu via a "propagate_upstream == true"
notification, then the dsa_port_mtu_change(propagate_upstream == false)
call that is immediately upcoming will break the MTU on the one DSA link
which is chip-wise local to the dp whose MTU is changing right now.
Example given this daisy chain topology:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
ip link set sw0p1 mtu 9000
ip link set sw1p1 mtu 9000 # at this stage, sw0p1 and sw1p1 can talk
# to one another using jumbo frames
ip link set sw0p2 mtu 1500 # this programs the sw0p3 DSA link first to
# the largest_mtu of 9000, then reprograms it to
# 1500 with the "propagate_upstream == false"
# notifier, breaking communication between
# sw0p1 and sw1p1
To escape from this situation, make the targeted match really match on a
single port - the user port, and rename the "propagate_upstream"
variable to "targeted_match" to clarify the intention and avoid future
issues.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a cross-chip topology like this:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
and we issue the following commands:
1. ip link set sw0p1 mtu 1700
2. ip link set sw1p1 mtu 1600
we notice the following happening:
Command 1. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 0, of 1700. This matches
sw0p0, sw0p3 and sw1p4 (all CPU ports and DSA links).
Then, it emits a targeted MTU notifier for the user port (sw0p1), again
with MTU 1700 (this doesn't matter).
Command 2. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 1, of 1600. This matches
the same group of ports as above, and decreases the MTU for the CPU port
and the DSA links from 1700 to 1600.
As a result, the sw0p1 user port can no longer communicate with its CPU
port at MTU 1700.
To address this, we should calculate the largest_mtu across all switches
that may share a CPU port, and only emit MTU notifiers with that value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the notifier for adding a multicast MAC address matches on
the targeted port and on all DSA links in the system, be they upstream
or downstream links.
This leads to a considerable amount of useless traffic.
Consider this daisy chain topology, and a MDB add notifier emitted on
sw0p0. It matches on sw0p0, sw0p3, sw1p3 and sw2p4.
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ x ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
But switch 0 has no reason to send the multicast traffic for that MAC
address on sw0p3, which is how it reaches switches 1 and 2. Those
switches don't expect, according to the user configuration, to receive
this multicast address from switch 1, and they will drop it anyway,
because the only valid destination is the port they received it on.
They only need to configure themselves to deliver that multicast address
_towards_ switch 1, where the MDB entry is installed.
Similarly, switch 1 should not send this multicast traffic towards
sw1p3, because that is how it reaches switch 2.
With this change, the heat map for this MDB notifier changes as follows:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Now the mdb notifier behaves the same as the fdb notifier.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between dsa_is_user_port and dsa_port_is_user is that the
former needs to look up the list of ports of the DSA switch tree in
order to find the struct dsa_port, while the latter directly receives it
as an argument.
dsa_is_user_port is already in widespread use and has its place, so
there isn't any chance of converting all callers to a single form.
But being able to do:
dsa_port_is_user(dp)
instead of
dsa_is_user_port(dp->ds, dp->index)
is much more efficient too, especially when the "dp" comes from an
iterator over the DSA switch tree - this reduces the complexity from
quadratic to linear.
Move these helpers from dsa2.c to include/net/dsa.h so that others can
use them too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cross-chip notifiers work by comparing each ds->index against the
info->sw_index value from the notifier. The ds->index is retrieved from
the device tree dsa,member property.
If a single tree cross-chip topology does not declare unique switch IDs,
this will result in hard-to-debug issues/voodoo effects such as the
cross-chip notifier for one switch port also matching the port with the
same number from another switch.
Check in dsa_switch_parse_member_of() whether the DSA switch tree
contains a DSA switch with the index we're preparing to add, before
actually adding it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current get_phy_flags() is only processed when we connect to a PHY
via a designed phy-handle property via phylink_of_phy_connect(), but if
we fallback on the internal MDIO bus created by a switch and take the
dsa_slave_phy_connect() path then we would not be processing that flag
and using it at PHY connection time.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamping procedure for SJA1105 is a bit unconventional
because the transmit procedure itself is unconventional.
Control packets (and therefore PTP as well) are transmitted to a
specific port in SJA1105 using "management routes" which must be written
over SPI to the switch. These are one-shot rules that match by
destination MAC address on traffic coming from the CPU port, and select
the precise destination port for that packet. So to transmit a packet
from NET_TX softirq context, we actually need to defer to a process
context so that we can perform that SPI write before we send the packet.
The DSA master dev_queue_xmit() runs in process context, and we poll
until the switch confirms it took the TX timestamp, then we annotate the
skb clone with that TX timestamp. This is why the sja1105 driver does
not need an skb queue for TX timestamping.
But the SJA1110 is a bit (not much!) more conventional, and you can
request 2-step TX timestamping through the DSA header, as well as give
the switch a cookie (timestamp ID) which it will give back to you when
it has the timestamp. So now we do need a queue for keeping the skb
clones until their TX timestamps become available.
The interesting part is that the metadata frames from SJA1105 haven't
disappeared completely. On SJA1105 they were used as follow-ups which
contained RX timestamps, but on SJA1110 they are actually TX completion
packets, which contain a variable (up to 32) array of timestamps.
Why an array? Because:
- not only is the TX timestamp on the egress port being communicated,
but also the RX timestamp on the CPU port. Nice, but we don't care
about that, so we ignore it.
- because a packet could be multicast to multiple egress ports, each
port takes its own timestamp, and the TX completion packet contains
the individual timestamps on each port.
This is unconventional because switches typically have a timestamping
FIFO and raise an interrupt, but this one doesn't. So the tagger needs
to detect and parse meta frames, and call into the main switch driver,
which pairs the timestamps with the skbs in the TX timestamping queue
which are waiting for one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has improved a few things compared to SJA1105:
- To send a control packet from the host port with SJA1105, one needed
to program a one-shot "management route" over SPI. This is no longer
true with SJA1110, you can actually send "in-band control extensions"
in the packets sent by DSA, these are in fact DSA tags which contain
the destination port and switch ID.
- When receiving a control packet from the switch with SJA1105, the
source port and switch ID were written in bytes 3 and 4 of the
destination MAC address of the frame (which was a very poor shot at a
DSA header). If the control packet also had an RX timestamp, that
timestamp was sent in an actual follow-up packet, so there were
reordering concerns on multi-core/multi-queue DSA masters, where the
metadata frame with the RX timestamp might get processed before the
actual packet to which that timestamp belonged (there is no way to
pair a packet to its timestamp other than the order in which they were
received). On SJA1110, this is no longer true, control packets have
the source port, switch ID and timestamp all in the DSA tags.
- Timestamps from the switch were partial: to get a 64-bit timestamp as
required by PTP stacks, one would need to take the partial 24-bit or
32-bit timestamp from the packet, then read the current PTP time very
quickly, and then patch in the high bits of the current PTP time into
the captured partial timestamp, to reconstruct what the full 64-bit
timestamp must have been. That is awful because packet processing is
done in NAPI context, but reading the current PTP time is done over
SPI and therefore needs sleepable context.
But it also aggravated a few things:
- Not only is there a DSA header in SJA1110, but there is a DSA trailer
in fact, too. So DSA needs to be extended to support taggers which
have both a header and a trailer. Very unconventional - my understanding
is that the trailer exists because the timestamps couldn't be prepared
in time for putting them in the header area.
- Like SJA1105, not all packets sent to the CPU have the DSA tag added
to them, only control packets do:
* the ones which match the destination MAC filters/traps in
MAC_FLTRES1 and MAC_FLTRES0
* the ones which match FDB entries which have TRAP or TAKETS bits set
So we could in theory hack something up to request the switch to take
timestamps for all packets that reach the CPU, and those would be
DSA-tagged and contain the source port / switch ID by virtue of the
fact that there needs to be a timestamp trailer provided. BUT:
- The SJA1110 does not parse its own DSA tags in a way that is useful
for routing in cross-chip topologies, a la Marvell. And the sja1105
driver already supports cross-chip bridging from the SJA1105 days.
It does that by automatically setting up the DSA links as VLAN trunks
which contain all the necessary tag_8021q RX VLANs that must be
communicated between the switches that span the same bridge. So when
using tag_8021q on sja1105, it is possible to have 2 switches with
ports sw0p0, sw0p1, sw1p0, sw1p1, and 2 VLAN-unaware bridges br0 and
br1, and br0 can take sw0p0 and sw1p0, and br1 can take sw0p1 and
sw1p1, and forwarding will happen according to the expected rules of
the Linux bridge.
We like that, and we don't want that to go away, so as a matter of
fact, the SJA1110 tagger still needs to support tag_8021q.
So the sja1110 tagger is a hybrid between tag_8021q for data packets,
and the native hardware support for control packets.
On RX, packets have a 13-byte trailer if they contain an RX timestamp.
That trailer is padded in such a way that its byte 8 (the start of the
"residence time" field - not parsed by Linux because we don't care) is
aligned on a 16 byte boundary. So the padding has a variable length
between 0 and 15 bytes. The DSA header contains the offset of the
beginning of the padding relative to the beginning of the frame (and the
end of the padding is obviously the end of the packet minus 13 bytes,
the length of the trailer). So we discard it.
Packets which don't have a trailer contain the source port and switch ID
information in the header (they are "trap-to-host" packets). Packets
which have a trailer contain the source port and switch ID in the trailer.
On TX, the destination port mask and switch ID is always in the trailer,
so we always need to say in the header that a trailer is present.
The header needs a custom EtherType and this was chosen as 0xdadc, after
0xdada which is for Marvell and 0xdadb which is for VLANs in
VLAN-unaware mode on SJA1105 (and SJA1110 in fact too).
Because we use tag_8021q in concert with the native tagging protocol,
control packets will have 2 DSA tags.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105, RX timestamps for packets sent to the CPU are transmitted in
separate follow-up packets (metadata frames). These contain partial
timestamps (24 or 32 bits) which are kept in SJA1105_SKB_CB(skb)->meta_tstamp.
Thankfully, SJA1110 improved that, and the RX timestamps are now
transmitted in-band with the actual packet, in the timestamp trailer.
The RX timestamps are now full-width 64 bits.
Because we process the RX DSA tags in the rcv() method in the tagger,
but we would like to preserve the DSA code structure in that we populate
the skb timestamp in the port_rxtstamp() call which only happens later,
the implication is that we must somehow pass the 64-bit timestamp from
the rcv() method all the way to port_rxtstamp(). We can use the skb->cb
for that.
Rename the meta_tstamp from struct sja1105_skb_cb from "meta_tstamp" to
"tstamp", and increase its size to 64 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The added value of this function is that it can deal with both the case
where the VLAN header is in the skb head, as well as in the offload field.
This is something I was not able to do using other functions in the
network stack.
Since both ocelot-8021q and sja1105 need to do the same stuff, let's
make it a common service provided by tag_8021q.
This is done as refactoring for the new SJA1110 tagger, which partly
uses tag_8021q as well (just like SJA1105), and will be the third caller.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes no sense and is not needed, it is probably a debugging
leftover.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some really really weird switches just couldn't decide whether to use a
normal or a tail tagger, so they just did both.
This creates problems for DSA, because we only have the concept of an
'overhead' which can be applied to the headroom or to the tailroom of
the skb (like for example during the central TX reallocation procedure),
depending on the value of bool tail_tag, but not to both.
We need to generalize DSA to cater for these odd switches by
transforming the 'overhead / tail_tag' pair into 'needed_headroom /
needed_tailroom'.
The DSA master's MTU is increased to account for both.
The flow dissector code is modified such that it only calls the DSA
adjustment callback if the tagger has a non-zero header length.
Taggers are trivially modified to declare either needed_headroom or
needed_tailroom, based on the tail_tag value that they currently
declare.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using sub-VLANs in the range of 1-7, the resulting value from:
rx_vid = dsa_8021q_rx_vid_subvlan(ds, port, subvlan);
is wrong according to the description from tag_8021q.c:
| 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+-----------+-----+-----------------+-----------+-----------------------+
| DIR | SVL | SWITCH_ID | SUBVLAN | PORT |
+-----------+-----+-----------------+-----------+-----------------------+
For example, when ds->index == 0, port == 3 and subvlan == 1,
dsa_8021q_rx_vid_subvlan() returns 1027, same as it returns for
subvlan == 0, but it should have returned 1043.
This is because the low portion of the subvlan bits are not masked
properly when writing into the 12-bit VLAN value. They are masked into
bits 4:3, but they should be masked into bits 5:4.
Fixes: 3eaae1d05f ("net: dsa: tag_8021q: support up to 8 VLANs per port using sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA implements a bunch of 'standardized' ethtool statistics counters,
namely tx_packets, tx_bytes, rx_packets, rx_bytes. So whatever the
hardware driver returns in .get_sset_count(), we need to add 4 to that.
That is ok, except that .get_sset_count() can return a negative error
code, for example:
b53_get_sset_count
-> phy_ethtool_get_sset_count
-> return -EIO
-EIO is -5, and with 4 added to it, it becomes -1, aka -EPERM. One can
imagine that certain error codes may even become positive, although
based on code inspection I did not see instances of that.
Check the error code first, if it is negative return it as-is.
Based on a similar patch for dsa_master_get_strings from Dan Carpenter:
https://patchwork.kernel.org/project/netdevbpf/patch/YJaSe3RPgn7gKxZv@mwanda/
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ds->ops->get_sset_count() fails then it "count" is a negative error
code such as -EOPNOTSUPP. Because "i" is an unsigned int, the negative
error code is type promoted to a very high value and the loop will
corrupt memory until the system crashes.
Fix this by checking for error codes and changing the type of "i" to
just int.
Fixes: badf3ada60 ("net: dsa: Provide CPU port statistics to master netdev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case ethernet driver is enabled and INET is disabled, selftest will
fail to build.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 3e1e58d64c ("net: add generic selftest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210428130947.29649-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a waste to clone skb directly in dsa_skb_tx_timestamp().
For one-step timestamping, a clone was not needed. For any failure of
port_txtstamp (this may usually happen), the skb clone had to be freed.
So this patch moves skb cloning for tx timestamp out of dsa core, and
let drivers clone skb in port_txtstamp if they really need.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ptp_classify_raw out of dsa core driver for handling tx
timestamp request. Let device drivers do this if they want.
Not all drivers want to limit tx timestamping for only PTP
packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx timestamp request in core driver at very beginning of
dsa_skb_tx_timestamp(), so that most skbs not requiring tx
timestamp just return. And drop such checking in device drivers.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with patch:
a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
drivers without "port_bridge_flags" callback will fail to join the bridge.
Looking at the code, -EOPNOTSUPP seems to be the proper return value,
which makes at least microchip and atheros switches work again.
Fixes: 5961d6a12c ("net: dsa: inherit the actual bridge port flags at join time")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some combinations of tag protocols and Ethernet controllers are
incompatible, and it is hard for the driver to keep track of these.
Therefore, allow the device tree author (typically the board vendor)
to inform the driver of this fact by selecting an alternate protocol
that is known to work.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously DSA ports were also included, on the assumption that the
protocol used by the CPU port had to the matched throughout the entire
tree.
As there is not yet any consumer in need of this, drop the call.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of generic selftest should be able to work with probably all ethernet
controllers. The DSA switches are not exception, so enable it by default at
least for DSA.
This patch was tested with SJA1105 and AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in bugfix commit 6ab4c3117a ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If PHY is not available on DSA port (described at devicetree but absent or
failed to detect) then kernel prints warning after 3700 secs:
[ 3707.948771] ------------[ cut here ]------------
[ 3707.948784] Type was not set for devlink port.
[ 3707.948894] WARNING: CPU: 1 PID: 17 at net/core/devlink.c:8097 0xc083f9d8
We should unregister the devlink port as a user port and
re-register it as an unused port before executing "continue" in case of
dsa_port_setup error.
Fixes: 86f8b1c01a ("net: dsa: Do not make user port errors fatal")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify "Apparantly" to "Apparently" in net/dsa/tag_rtl4_a.c..
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is aware of switches with global VLAN filtering since the blamed
commit, but it makes a bad decision when multiple bridges are spanning
the same switch:
ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br0
ip link set swp4 master br1
ip link set swp5 master br1
ip link set swp5 nomaster
ip link set swp4 nomaster
[138665.939930] sja1105 spi0.1: port 3: dsa_core: VLAN filtering is a global setting
[138665.947514] DSA: failed to notify DSA_NOTIFIER_BRIDGE_LEAVE
When all ports leave br1, DSA blindly attempts to disable VLAN filtering
on the switch, ignoring the fact that br0 still exists and is VLAN-aware
too. It fails while doing that.
This patch checks whether any port exists at all and is under a
VLAN-aware bridge.
Fixes: d371b7c92d ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa infrastructure provides a well-defined hierarchy of devices,
pass up the call to set up the flow block to the master device. From the
software dataplane, the netfilter infrastructure uses the dsa slave
devices to refer to the input and output device for the given skbuff.
Similarly, the flowtable definition in the ruleset refers to the dsa
slave port devices.
This patch adds the glue code to call ndo_setup_tc with TC_SETUP_FT
with the master device via the dsa slave devices.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .ndo_fill_forward_path for dsa slave port devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we join an already-created bridge port, such as a bond master
interface, then we can miss the initial switchdev notifications emitted
by the bridge for this port, while it wasn't offloaded by anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently assumes that the bridge port starts off with this
constellation of bridge port flags:
- learning on
- unicast flooding on
- multicast flooding on
- broadcast flooding on
just by virtue of code copy-pasta from the bridge layer (new_nbp).
This was a simple enough strategy thus far, because the 'bridge join'
moment always coincided with the 'bridge port creation' moment.
But with sandwiched interfaces, such as:
br0
|
bond0
|
swp0
it may happen that the user has had time to change the bridge port flags
of bond0 before enslaving swp0 to it. In that case, swp0 will falsely
assume that the bridge port flags are those determined by new_nbp, when
in fact this can happen:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set bond0 type bridge_slave learning off
ip link set swp0 master br0
Now swp0 has learning enabled, bond0 has learning disabled. Not nice.
Fix this by "dumpster diving" through the actual bridge port flags with
br_port_flag_is_set, at bridge join time.
We use this opportunity to split dsa_port_change_brport_flags into two
distinct functions called dsa_port_inherit_brport_flags and
dsa_port_clear_brport_flags, now that the implementation for the two
cases is no longer similar. This patch also creates two functions called
dsa_port_switchdev_sync and dsa_port_switchdev_unsync which collect what
we have so far, even if that's asymmetrical. More is going to be added
in the next patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a pretty noisy change that was broken out of the larger change
for replaying switchdev attributes and objects at bridge join time,
which is when these extack objects are actually used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA can properly detect and offload this sequence of operations:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set swp0 master bond0
ip link set bond0 master br0
But not this one:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
Actually the second one is more complicated, due to the elapsed time
between the enslavement of bond0 and the offloading of it via swp0, a
lot of things could have happened to the bond0 bridge port in terms of
switchdev objects (host MDBs, VLANs, altered STP state etc). So this is
a bit of a can of worms, and making sure that the DSA port's state is in
sync with this already existing bridge port is handled in the next
patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a temporary variable to hold the return value from
dsa_tag_driver_get() instead of assigning it to dst->tag_ops. Leaving
an error value in dst->tag_ops can result in deferencing an invalid
pointer when a deferred switch configuration happens later.
Fixes: 357f203bb3 ("net: dsa: keep a copy of the tagging protocol in the DSA switch tree")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove CONFIG_HAVE_NET_DSA.
CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Currently, all drivers has explicit 'depends on NET_DSA', so this is
no more needed.
2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones.
- dropped !S390 dependency which was introduced to be sure NET_DSA
can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years
ago and the PHY library itself doesn't depend on !S390 since
commit 870a2b5e4f ("phylib: remove !S390 dependeny from Kconfig");
- INET dependency is kept to be sure we can select NET_SWITCHDEV;
- NETDEVICES dependency is kept to be sure we can select PHYLINK.
3. DSA drivers menu now depends on NET_DSA.
Instead on 'depends on NET_DSA' on every single driver, the entire
menu now depends on it. This eliminates a lot of duplicated lines
from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can
be only m or n).
This also has a nice side effect that there's no more empty menu on
configurations without DSA.
4. Kbuild will now descend into 'drivers/net/dsa' only when
CONFIG_NET_DSA is y or m.
This is safe since no objects inside this folder can be built without
DSA core, as well as when CONFIG_NET_DSA=m, no objects can be
built-in.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for a driver to be able to query a bridge for information
about itself, e.g. reading out port flags, it has to use a netdev that
is known to the bridge. In the simple case, that is just the netdev
representing the port, e.g. swp0 or swp1 in this example:
br0
/ \
swp0 swp1
But in the case of an offloaded lag, this will be the bond or team
interface, e.g. bond0 in this example:
br0
/
bond0
/ \
swp0 swp1
Add a helper that hides some of this complexity from the
drivers. Then, redefine dsa_port_offloads_bridge_port using the helper
to avoid double accounting of the set of possible offloaded uppers.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for legacy Broadcom tags, which are similar to DSA_TAG_PROTO_BRCM.
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when extracting frames from CPU the cpuq is not used anymore so
remove it.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support port MDB and bridge flag operations.
As the hardware can manage multicast forwarding itself, offload_fwd_mark
can be unconditionally set to true.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias reports that after the blamed patch, VLAN objects being added to
a bridge device are being added to all slave ports instead (swp2, swp3).
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br0
bridge vlan add dev br0 vid 100 self
This is because the fix was too broad: we made dsa_port_offloads_netdev
say "yes, I offload the br0 bridge" for all slave ports, but we didn't
add the checks whether the switchdev object was in fact meant for the
physical port or for the bridge itself. So we are reacting on events in
a way in which we shouldn't.
The reason why the fix was too broad is because the question itself,
"does this DSA port offload this netdev", was too broad in the first
place. The solution is to disambiguate the question and separate it into
two different functions, one to be called for each switchdev attribute /
object that has an orig_dev == net_bridge (dsa_port_offloads_bridge),
and the other for orig_dev == net_bridge_port (*_offloads_bridge_port).
In the case of VLAN objects on the bridge interface, this solves the
problem because we know that VLAN objects are per bridge port and not
per bridge. And when orig_dev is equal to the net_bridge, we offload it
as a bridge, but not as a bridge port; that's how we are able to skip
reacting on those events. Note that this is compatible with future plans
to have explicit offloading of VLAN objects on the bridge interface as a
bridge port (in DSA, this signifies that we should add that VLAN towards
the CPU port).
Fixes: 99b8202b17 ("net: dsa: fix SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING getting ignored")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A different TPID bit is used for 802.1ad VLAN frames.
Reported-by: Ilario Gelmetti <iochesonome@gmail.com>
Fixes: f0af34317f ("net: dsa: mediatek: combine MediaTek tag with VLAN tag")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86dd9868b8 has several issues, but was accepted too soon
before anyone could take a look.
- Double free. dsa_slave_xmit() will free the skb if the xmit function
returns NULL, but the skb is already freed by eth_skb_pad(). Use
__skb_put_padto() to avoid that.
- Unnecessary allocation. It has been done by DSA core since commit
a3b0b64797.
- A u16 pointer points to skb data. It should be __be16 for network
byte order.
- Typo in comments. "numer" -> "number".
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ocelot driver code is in a library, the dsa tag
code cannot be built-in:
ld.lld: error: undefined symbol: ocelot_can_inject
>>> referenced by tag_ocelot_8021q.c
>>> dsa/tag_ocelot_8021q.o:(ocelot_xmit) in archive net/built-in.a
ld.lld: error: undefined symbol: ocelot_port_inject_frame
>>> referenced by tag_ocelot_8021q.c
>>> dsa/tag_ocelot_8021q.o:(ocelot_xmit) in archive net/built-in.a
Building the tag support only really makes sense for compile-testing
when the driver is available, so add a Kconfig dependency that prevents
the broken configuration while allowing COMPILE_TEST alternative when
MSCC_OCELOT_SWITCH_LIB is disabled entirely. This case is handled
through the #ifdef check in include/soc/mscc/ocelot.h.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210225143910.3964364-2-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The core DSA framework uses hsr_is_master() which would not resolve to a
valid symbol if HSR is built-into the kernel and DSA is a module.
Fixes: 18596f504a ("net: dsa: add support for offloading HSR")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210220051222.15672-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support also transmitting frames using the custom "8899 A"
4 byte tag.
Qingfang came up with the solution: we need to pad the
ethernet frame to 60 bytes using eth_skb_pad(), then the
switch will happily accept frames with custom tags.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: efd7fe68f0 ("net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement functions 'port_mrp_add', 'port_mrp_del',
'port_mrp_add_ring_role' and 'port_mrp_del_ring_role' to call the mrp
functions from ocelot.
Also all MRP frames that arrive to CPU on queue number OCELOT_MRP_CPUQ
will be forward by the SW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading MRP in HW. Currently implement the switchdev
calls 'SWITCHDEV_OBJ_ID_MRP', 'SWITCHDEV_OBJ_ID_RING_ROLE_MRP',
to allow to create MRP instances and to set the role of these instances.
Add DSA_NOTIFIER_MRP_ADD/DEL and DSA_NOTIFIER_MRP_ADD/DEL_RING_ROLE
which calls to .port_mrp_add/del and .port_mrp_add/del_ring_role in the
DSA driver for the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch is confused by the fact that a 32-bit BIT(port) macro is passed
as argument to the ocelot_ifh_set_dest function and warns:
ocelot_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
seville_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
The destination port mask is copied into a 12-bit field of the packet,
starting at bit offset 67 and ending at 56.
So this DSA tagging protocol supports at most 12 bits, which is clearly
less than 32. Attempting to send to a port number > 12 will cause the
packing() call to truncate way before there will be 32-bit truncation
due to type promotion of the BIT(port) argument towards u64.
Therefore, smatch's fears that BIT(port) will do the wrong thing and
cause unexpected truncation for "port" values >= 32 are unfounded.
Nonetheless, let's silence the warning by explicitly passing an u64
value to ocelot_ifh_set_dest, such that the compiler does not need to do
a questionable type promotion.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the tag_8021q tagger is software-defined, it has no means by
itself for retrieving hardware timestamps of PTP event messages.
Because we do want to support PTP on ocelot even with tag_8021q, we need
to use the CPU port module for that. The RX timestamp is present in the
Extraction Frame Header. And because we can't use NPI mode which redirects
the CPU queues to an "external CPU" (meaning the ARM CPU running Linux),
then we need to poll the CPU port module through the MMIO registers to
retrieve TX and RX timestamps.
Sadly, on NXP LS1028A, the Felix switch was integrated into the SoC
without wiring the extraction IRQ line to the ARM GIC. So, if we want to
be notified of any PTP packets received on the CPU port module, we have
a problem.
There is a possible workaround, which is to use the Ethernet CPU port as
a notification channel that packets are available on the CPU port module
as well. When a PTP packet is received by the DSA tagger (without timestamp,
of course), we go to the CPU extraction queues, poll for it there, then
we drop the original Ethernet packet and masquerade the packet retrieved
over MMIO (plus the timestamp) as the original when we inject it up the
stack.
Create a quirk in struct felix is selected by the Felix driver (but not
by Seville, since that doesn't support PTP at all). We want to do this
such that the workaround is minimally invasive for future switches that
don't require this workaround.
The only traffic for which we need timestamps is PTP traffic, so add a
redirection rule to the CPU port module for this. Currently we only have
the need for PTP over L2, so redirection rules for UDP ports 319 and 320
are TBD for now.
Note that for the workaround of matching of PTP-over-Ethernet-port with
PTP-over-MMIO queues to work properly, both channels need to be
absolutely lossless. There are two parts to achieving that:
- We keep flow control enabled on the tag_8021q CPU port
- We put the DSA master interface in promiscuous mode, so it will never
drop a PTP frame (for the profiles we are interested in, these are
sent to the multicast MAC addresses of 01-80-c2-00-00-0e and
01-1b-19-00-00-00).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce5
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one place where we cannot avoid accessing driver data, and that
is 2-step PTP TX timestamping, since the switch wants us to provide a
timestamp request ID through the injection header, which naturally must
come from a sequence number kept by the driver (it is generated by the
.port_txtstamp method prior to the tagger's xmit).
However, since other drivers like dsa_loop do not claim PTP support
anyway, the DSA_SKB_CB(skb)->clone will always be NULL anyway, so if we
move all PTP-related dereferences of struct ocelot and struct ocelot_port
into a separate function, we can effectively ensure that this is dead
code when the ocelot tagger is attached to non-ocelot switches, and the
stateful portion of the tagger is more self-contained.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taggers should be written to do something valid irrespective of the
switch driver that they are attached to. This is even more true now,
because since the introduction of the .change_tag_protocol method, a
certain tagger is not necessarily strictly associated with a driver any
longer, and I would like to be able to test all taggers with dsa_loop in
the future.
In the case of ocelot, it needs to move the classified VLAN from the DSA
tag into the skb if the port is VLAN-aware. We can allow it to do that
by looking at the dp->vlan_filtering property, no need to invoke
structures which are specific to ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.
One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.
Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.
Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it. If it does, there
will need to be a dedicated .port_set_mrouter anyway.
So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.
The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:
behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)
so there was no reason to entangle them in the first place.
Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a DSA switch port operating in standalone mode, address learning
doesn't make much sense since that is a bridge function. In fact,
address learning even breaks setups such as this one:
+---------------------------------------------+
| |
| +-------------------+ |
| | br0 | send receive |
| +--------+-+--------+ +--------+ +--------+ |
| | | | | | | | | |
| | swp0 | | swp1 | | swp2 | | swp3 | |
| | | | | | | | | |
+-+--------+-+--------+-+--------+-+--------+-+
| ^ | ^
| | | |
| +-----------+ |
| |
+--------------------------------+
because if the switch has a single FDB (can offload a single bridge)
then source address learning on swp3 can "steal" the source MAC address
of swp2 from br0's FDB, because learning frames coming from swp2 will be
done twice: first on the swp1 ingress port, second on the swp3 ingress
port. So the hardware FDB will become out of sync with the software
bridge, and when swp2 tries to send one more packet towards swp1, the
ASIC will attempt to short-circuit the forwarding path and send it
directly to swp3 (since that's the last port it learned that address on),
which it obviously can't, because swp3 operates in standalone mode.
So DSA drivers operating in standalone mode should still configure a
list of bridge port flags even when they are standalone. Currently DSA
attempts to call dsa_port_bridge_flags with 0, which disables egress
flooding of unknown unicast and multicast, something which doesn't make
much sense. For the switches that implement .port_egress_floods - b53
and mv88e6xxx, it probably doesn't matter too much either, since they
can possibly inject traffic from the CPU into a standalone port,
regardless of MAC DA, even if egress flooding is turned off for that
port, but certainly not all DSA switches can do that - sja1105, for
example, can't. So it makes sense to use a better common default there,
such as "flood everything".
It should also be noted that what DSA calls "dsa_port_bridge_flags()"
is a degenerate name for just calling .port_egress_floods(), since
nothing else is implemented - not learning, in particular. But disabling
address learning, something that this driver is also coding up for, will
be supported by individual drivers once .port_egress_floods is replaced
with a more generic .port_bridge_flags.
Previous attempts to code up this logic have been in the common bridge
layer, but as pointed out by Ido Schimmel, there are corner cases that
are missed when doing that:
https://patchwork.kernel.org/project/netdevbpf/patch/20210209151936.97382-5-olteanv@gmail.com/
So, at least for now, let's leave DSA in charge of setting port flags
before and after the bridge join and leave.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add offloading for HSR/PRP (IEC 62439-3) tag insertion, tag removal
forwarding and duplication supported by the xrs7000 series switches.
Only HSR v1 and PRP v1 are supported by the xrs7000 series switches (HSR
v0 is not).
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding on DSA switches.
Add DSA_NOTIFIER_HSR_JOIN and DSA_NOTIFIER_HSR_LEAVE which trigger calls
to .port_hsr_join and .port_hsr_leave in the DSA driver for the switch.
The DSA switch driver should then set netdev feature flags for the
HSR/PRP operation that it offloads.
NETIF_F_HW_HSR_TAG_INS
NETIF_F_HW_HSR_TAG_RM
NETIF_F_HW_HSR_FWD
NETIF_F_HW_HSR_DUP
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given the following topology, and focusing only on Box A:
Box A
+----------------------------------+
| Board 1 br0 |
| +---------+ |
| / \ |
| | | |
| | bond0 |
| | +-----+ |
|192.168.1.1 | / \ |
| eno0 swp0 swp1 swp2 |
+---|--------|-------|-------|-----+
| | | |
+--------+ | |
Cable | |
Cable| |Cable
Cable | |
+--------+ | |
| | | |
+---|--------|-------|-------|-----+
| eno0 swp0 swp1 swp2 |
|192.168.1.2 | \ / |
| | +-----+ |
| | bond0 |
| | | |
| \ / |
| +---------+ |
| Board 2 br0 |
+----------------------------------+
Box B
The assisted_learning_on_cpu_port logic will see that swp0 is bridged
with a "foreign interface" (bond0) and will therefore install all
addresses learnt by the software bridge towards bond0 (including the
address of eno0 on Box B) as static addresses towards the CPU port.
But that's not what we want - bond0 is not really a "foreign interface"
but one we can offload including L2 forwarding from/towards it. So we
need to refine our logic for assisted learning such that, whenever we
see an address learnt on a non-DSA interface, we search through the tree
for any port that offloads that non-DSA interface.
Some confusion might arise as to why we search through the whole tree
instead of just the local switch returned by dsa_slave_dev_lower_find.
Or a different angle of the same confusion: why does
dsa_slave_dev_lower_find(br_dev) return a single dp that's under br_dev
instead of the whole list of bridged DSA ports?
To answer the second question, it should be enough to install the static
FDB entry on the CPU port of a single switch in the tree, because
dsa_port_fdb_add uses DSA_NOTIFIER_FDB_ADD which ensures that all other
switches in the tree get notified of that address, and add the entry
themselves using dsa_towards_port().
This should help understand the answer to the first question: the port
returned by dsa_slave_dev_lower_find may not be on the same switch as
the ports that offload the LAG. Nonetheless, if the driver implements
.crosschip_lag_join and .crosschip_bridge_join as mv88e6xxx does, there
still isn't any reason for trapping addresses learnt on the remote LAG
towards the CPU, and we should prevent that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is not fixing any actual bug that I know of, but having a DSA
interface that is up even when its lower (master) interface is down is
one of those things that just do not sound right.
Yes, DSA checks if the master is up before actually bringing the
user interface up, but nobody prevents bringing the master interface
down immediately afterwards... Then the user ports would attempt
dev_queue_xmit on an interface that is down, and wonder what's wrong.
This patch prevents that from happening. NETDEV_GOING_DOWN is the
notification emitted _before_ the master actually goes down, and we are
protected by the rtnl_mutex, so all is well.
For those of you reading this because you were doing switch testing
such as latency measurements for autonomously forwarded traffic, and you
needed a controlled environment with no extra packets sent by the
network stack, this patch breaks that, because now the user ports go
down too, which may shut down the PHY etc. But please don't do it like
that, just do instead:
tc qdisc add dev eno2 clsact
tc filter add dev eno2 egress flower action drop
Tested with two cascaded DSA switches:
$ ip link set eno2 down
sja1105 spi2.0 sw0p2: Link is Down
mscc_felix 0000:00:00.5 swp0: Link is Down
fsl_enetc 0000:00:00.2 eno2: Link is Down
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA wants the master interface to be open before the user port is due to
historical reasons. The promiscuity of interfaces that are down used to
have issues, as referenced Lennert Buytenhek in commit df02c6ff2e
("dsa: fix master interface allmulti/promisc handling").
The bugfix mentioned there, commit b6c40d68ff ("net: only invoke
dev->change_rx_flags when device is UP"), was basically a "don't do
that" approach to working around the promiscuity while down issue.
Further work done by Vlad Yasevich in commit d2615bf450 ("net: core:
Always propagate flag changes to interfaces") has resolved the
underlying issue, and it is strictly up to the DSA and 8021q drivers
now, it is no longer mandated by the networking core that the master
interface must be up when changing its promiscuity.
From DSA's point of view, deciding to error out in dsa_slave_open
because the master isn't up is
(a) a bad user experience and
(b) knocking at an open door.
Even if there still was an issue with promiscuity while down, DSA could
still just open the master and avoid it.
Doing it this way has the additional benefit that user space can now
remove DSA-specific workarounds, like systemd-networkd with BindCarrier:
https://github.com/systemd/systemd/issues/7478
And we can finally remove one of the 2 bullets in the "Common pitfalls
using DSA setups" chapter.
Tested with two cascaded DSA switches:
$ ip link set sw0p2 up
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 1Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp0: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off
8021q: adding VLAN 0 to HW filter on device swp0
sja1105 spi2.0 sw0p2: configuring for phy/rgmii-id link mode
IPv6: ADDRCONF(NETDEV_CHANGE): eno2: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since teardown is supposed to undo the effects of the setup method, it
should be called in the error path for dsa_switch_setup, not just in
dsa_switch_teardown.
Fixes: 5e3f847a02 ("net: dsa: Add teardown callback for drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210204163351.2929670-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bridge emits VLAN filtering events and quite a few others via
switchdev with orig_dev = br->dev. After the blamed commit, these events
started getting ignored.
The point of the patch was to not offload switchdev objects for ports
that didn't go through dsa_port_bridge_join, because the configuration
is unsupported:
- ports that offload a bonding/team interface go through
dsa_port_bridge_join when that bonding/team interface is later bridged
with another switch port or LAG
- ports that don't offload LAG don't get notified of the bridge that is
on top of that LAG.
Sadly, a check is missing, which is that the orig_dev is equal to the
bridge device. This check is compatible with the original intention,
because ports that don't offload bridging because they use a software
LAG don't have dp->bridge_dev set.
On a semi-related note, we should not offload switchdev objects or
populate dp->bridge_dev if the driver doesn't implement .port_bridge_join
either. However there is no regression associated with that, so it can
be done separately.
Fixes: 5696c8aedf ("net: dsa: Don't offload port attributes on standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20210202233109.1591466-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are use cases for which the existing tagger, based on the NPI
(Node Processor Interface) functionality, is insufficient.
Namely:
- Frames injected through the NPI port bypass the frame analyzer, so no
source address learning is performed, no TSN stream classification,
etc.
- Flow control is not functional over an NPI port (PAUSE frames are
encapsulated in the same Extraction Frame Header as all other frames)
- There can be at most one NPI port configured for an Ocelot switch. But
in NXP LS1028A and T1040 there are two Ethernet CPU ports. The non-NPI
port is currently either disabled, or operated as a plain user port
(albeit an internally-facing one). Having the ability to configure the
two CPU ports symmetrically could pave the way for e.g. creating a LAG
between them, to increase bandwidth seamlessly for the system.
So there is a desire to have an alternative to the NPI mode. This change
keeps the default tagger for the Seville and Felix switches as "ocelot",
but it can be changed via the following device attribute:
echo ocelot-8021q > /sys/class/<dsa-master>/dsa/tagging
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently DSA exposes the following sysfs:
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
which is a read-only device attribute, introduced in the kernel as
commit 98cdb48071 ("net: dsa: Expose tagging protocol to user-space"),
and used by libpcap since its commit 993db3800d7d ("Add support for DSA
link-layer types").
It would be nice if we could extend this device attribute by making it
writable:
$ echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
This is useful with DSA switches that can make use of more than one
tagging protocol. It may be useful in dsa_loop in the future too, to
perform offline testing of various taggers, or for changing between dsa
and edsa on Marvell switches, if that is desirable.
In terms of implementation, drivers can support this feature by
implementing .change_tag_protocol, which should always leave the switch
in a consistent state: either with the new protocol if things went well,
or with the old one if something failed. Teardown of the old protocol,
if necessary, must be handled by the driver.
Some things remain as before:
- The .get_tag_protocol is currently only called at probe time, to load
the initial tagging protocol driver. Nonetheless, new drivers should
report the tagging protocol in current use now.
- The driver should manage by itself the initial setup of tagging
protocol, no later than the .setup() method, as well as destroying
resources used by the last tagger in use, no earlier than the
.teardown() method.
For multi-switch DSA trees, error handling is a bit more complicated,
since e.g. the 5th out of 7 switches may fail to change the tag
protocol. When that happens, a revert to the original tag protocol is
attempted, but that may fail too, leaving the tree in an inconsistent
state despite each individual switch implementing .change_tag_protocol
transactionally. Since the intersection between drivers that implement
.change_tag_protocol and drivers that support D in DSA is currently the
empty set, the possibility for this error to happen is ignored for now.
Testing:
$ insmod mscc_felix.ko
[ 79.549784] mscc_felix 0000:00:00.5: Adding to iommu group 14
[ 79.565712] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
$ insmod tag_ocelot.ko
$ rmmod mscc_felix.ko
$ insmod mscc_felix.ko
[ 97.261724] libphy: VSC9959 internal MDIO bus: probed
[ 97.267363] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0
[ 97.274998] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1
[ 97.282561] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2
[ 97.289700] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3
[ 97.599163] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.862034] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.950731] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[ 97.964278] 8021q: adding VLAN 0 to HW filter on device swp0
[ 98.146161] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.238649] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[ 98.251845] 8021q: adding VLAN 0 to HW filter on device swp1
[ 98.433916] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.485542] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[ 98.503584] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 98.527948] device eno2 entered promiscuous mode
[ 98.544755] DSA: tree 0 setup
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=2.337 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.754 ms
^C
- 10.0.0.1 ping statistics -
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.754/1.545/2.337 ms
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
$ cat ./test_ocelot_8021q.sh
#!/bin/bash
ip link set swp0 down
ip link set swp1 down
ip link set swp2 down
ip link set swp3 down
ip link set swp5 down
ip link set eno2 down
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
ip link set eno2 up
ip link set swp0 up
ip link set swp1 up
ip link set swp2 up
ip link set swp3 up
ip link set swp5 up
$ ./test_ocelot_8021q.sh
./test_ocelot_8021q.sh: line 9: echo: write error: Protocol not available
$ rmmod tag_ocelot.ko
rmmod: can't unload module 'tag_ocelot': Resource temporarily unavailable
$ insmod tag_ocelot_8021q.ko
$ ./test_ocelot_8021q.sh
$ cat /sys/class/net/eno2/dsa/tagging
ocelot-8021q
$ rmmod tag_ocelot.ko
$ rmmod tag_ocelot_8021q.ko
rmmod: can't unload module 'tag_ocelot_8021q': Resource temporarily unavailable
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=0.953 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.787 ms
64 bytes from 10.0.0.1: seq=2 ttl=64 time=0.771 ms
$ rmmod mscc_felix.ko
[ 645.544426] mscc_felix 0000:00:00.5: Link is Down
[ 645.838608] DSA: tree 0 torn down
$ rmmod tag_ocelot_8021q.ko
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cascading DSA switches can be done multiple ways. There is the brute
force approach / tag stacking, where one upstream switch, located
between leaf switches and the host Ethernet controller, will just
happily transport the DSA header of those leaf switches as payload.
For this kind of setups, DSA works without any special kind of treatment
compared to a single switch - they just aren't aware of each other.
Then there's the approach where the upstream switch understands the tags
it transports from its leaves below, as it doesn't push a tag of its own,
but it routes based on the source port & switch id information present
in that tag (as opposed to DMAC & VID) and it strips the tag when
egressing a front-facing port. Currently only Marvell implements the
latter, and Marvell DSA trees contain only Marvell switches.
So it is safe to say that DSA trees already have a single tag protocol
shared by all switches, and in fact this is what makes the switches able
to understand each other. This fact is also implied by the fact that
currently, the tagging protocol is reported as part of a sysfs installed
on the DSA master and not per port, so it must be the same for all the
ports connected to that DSA master regardless of the switch that they
belong to.
It's time to make this official and enforce it (yes, this also means we
won't have any "switch understands tag to some extent but is not able to
speak it" hardware oddities that we'll support in the future).
This is needed due to the imminent introduction of the dsa_switch_ops::
change_tag_protocol driver API. When that is introduced, we'll have
to notify switches of the tagging protocol that they're configured to
use. Currently the tag_ops structure pointer is held only for CPU ports.
But there are switches which don't have CPU ports and nonetheless still
need to be configured. These would be Marvell leaf switches whose
upstream port is just a DSA link. How do we inform these of their
tagging protocol setup/deletion?
One answer to the above would be: iterate through the DSA switch tree's
ports once, list the CPU ports, get their tag_ops, then iterate again
now that we have it, and notify everybody of that tag_ops. But what to
do if conflicts appear between one cpu_dp->tag_ops and another? There's
no escaping the fact that conflict resolution needs to be done, so we
can be upfront about it.
Ease our work and just keep the master copy of the tag_ops inside the
struct dsa_switch_tree. Reference counting is now moved to be per-tree
too, instead of per-CPU port.
There are many places in the data path that access master->dsa_ptr->tag_ops
and we would introduce unnecessary performance penalty going through yet
another indirection, so keep those right where they are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existence of dsa_broadcast has generated some confusion in the past:
https://www.mail-archive.com/netdev@vger.kernel.org/msg365042.html
So let's document the existing dsa_port_notify and dsa_broadcast
functions and explain when each of them should be used.
Also, in fact, the in-between function has always been there but was
lacking a name, and is the main reason for this patch: dsa_tree_notify.
Refactor dsa_broadcast to use it.
This patch also moves dsa_broadcast (a top-level function) to dsa2.c,
where it really belonged in the first place, but had no companion so it
stood with dsa_port_notify.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sja1105 implementation can be blind about this, but the felix driver
doesn't do exactly what it's being told, so it needs to know whether it
is a TX or an RX VLAN, so it can install the appropriate type of TCAM
rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switches that care about QoS might have hardware support for reserving
buffer pools for individual ports or traffic classes, and configuring
their sizes and thresholds. Through devlink-sb (shared buffers), this is
all configurable, as well as their occupancy being viewable.
Add the plumbing in DSA for these operations.
Individual drivers still need to call devlink_sb_register() with the
shared buffers they want to expose. A helper was not created in DSA for
this purpose (unlike, say, dsa_devlink_params_register), since in my
opinion it does not bring any benefit over plainly calling
devlink_sb_register() directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 54a0ed0df4 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for Arrow SpeedChips XRS700x single byte tag trailer. This
is modeled on tag_trailer.c which works in a similar way.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packets ingressing on a LAG that egress on the CPU port, which are not
classified as management, will have a FORWARD tag that does not
contain the normal source device/port tuple. Instead the trunk bit
will be set, and the port field holds the LAG id.
Since the exact source port information is not available in the tag,
frames are injected directly on the LAG interface and thus do never
pass through any DSA port interface on ingress.
Management frames (TO_CPU) are not affected and will pass through the
DSA port interface as usual.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Monitor the following events and notify the driver when:
- A DSA port joins/leaves a LAG.
- A LAG, made up of DSA ports, joins/leaves a bridge.
- A DSA port in a LAG is enabled/disabled (enabled meaning
"distributing" in 802.3ad LACP terms).
When a LAG joins a bridge, the DSA subsystem will treat that as each
individual port joining the bridge. The driver may look at the port's
LAG device pointer to see if it is associated with any LAG, if that is
required. This is analogue to how switchdev events are replicated out
to all lower devices when reaching e.g. a LAG.
Drivers can optionally request that DSA maintain a linear mapping from
a LAG ID to the corresponding netdev by setting ds->num_lag_ids to the
desired size.
In the event that the hardware is not capable of offloading a
particular LAG for any reason (the typical case being use of exotic
modes like broadcast), DSA will take a hands-off approach, allowing
the LAG to be formed as a pure software construct. This is reported
back through the extended ACK, but is otherwise transparent to the
user.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a situation where a standalone port is indirectly attached to a
bridge (e.g. via a LAG) which is not offloaded, do not offload any
port attributes either. The port should behave as a standard NIC.
Previously, on mv88e6xxx, this meant that in the following setup:
br0
/
team0
/ \
swp0 swp1
If vlan filtering was enabled on br0, swp0's and swp1's QMode was set
to "secure". This caused all untagged packets to be dropped, as their
default VID (0) was not loaded into the VTU.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian reported a use-after-free bug in devlink_nl_port_fill found with
KASAN:
(devlink_nl_port_fill)
(devlink_port_notify)
(devlink_port_unregister)
(dsa_switch_teardown.part.3)
(dsa_tree_teardown_switches)
(dsa_unregister_switch)
(bcm_sf2_sw_remove)
(platform_remove)
(device_release_driver_internal)
(device_links_unbind_consumers)
(device_release_driver_internal)
(device_driver_detach)
(unbind_store)
Allocated by task 31:
alloc_netdev_mqs+0x5c/0x50c
dsa_slave_create+0x110/0x9c8
dsa_register_switch+0xdb0/0x13a4
b53_switch_register+0x47c/0x6dc
bcm_sf2_sw_probe+0xaa4/0xc98
platform_probe+0x90/0xf4
really_probe+0x184/0x728
driver_probe_device+0xa4/0x278
__device_attach_driver+0xe8/0x148
bus_for_each_drv+0x108/0x158
Freed by task 249:
free_netdev+0x170/0x194
dsa_slave_destroy+0xac/0xb0
dsa_port_teardown.part.2+0xa0/0xb4
dsa_tree_teardown_switches+0x50/0xc4
dsa_unregister_switch+0x124/0x250
bcm_sf2_sw_remove+0x98/0x13c
platform_remove+0x44/0x5c
device_release_driver_internal+0x150/0x254
device_links_unbind_consumers+0xf8/0x12c
device_release_driver_internal+0x84/0x254
device_driver_detach+0x30/0x34
unbind_store+0x90/0x134
What happens is that devlink_port_unregister emits a netlink
DEVLINK_CMD_PORT_DEL message which associates the devlink port that is
getting unregistered with the ifindex of its corresponding net_device.
Only trouble is, the net_device has already been unregistered.
It looks like we can stub out the search for a corresponding net_device
if we clear the devlink_port's type. This looks like a bit of a hack,
but also seems to be the reason why the devlink_port_type_clear function
exists in the first place.
Fixes: 3122433eb5 ("net: dsa: Register devlink ports before calling DSA driver setup()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian fainelli <f.fainelli@gmail.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210112004831.3778323-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the following happens when a DSA master driver unbinds while
there are DSA switches attached to it:
$ echo 0000:00:00.5 > /sys/bus/pci/drivers/mscc_felix/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 392 at net/core/dev.c:9507
Call trace:
rollback_registered_many+0x5fc/0x688
unregister_netdevice_queue+0x98/0x120
dsa_slave_destroy+0x4c/0x88
dsa_port_teardown.part.16+0x78/0xb0
dsa_tree_teardown_switches+0x58/0xc0
dsa_unregister_switch+0x104/0x1b8
felix_pci_remove+0x24/0x48
pci_device_remove+0x48/0xf0
device_release_driver_internal+0x118/0x1e8
device_driver_detach+0x28/0x38
unbind_store+0xd0/0x100
Located at the above location is this WARN_ON:
/* Notifier chain MUST detach us all upper devices. */
WARN_ON(netdev_has_any_upper_dev(dev));
Other stacked interfaces, like VLAN, do indeed listen for
NETDEV_UNREGISTER on the real_dev and also unregister themselves at that
time, which is clearly the behavior that rollback_registered_many
expects. But DSA interfaces are not VLAN. They have backing hardware
(platform devices, PCI devices, MDIO, SPI etc) which have a life cycle
of their own and we can't just trigger an unregister from the DSA
framework when we receive a netdev notifier that the master unregisters.
Luckily, there is something we can do, and that is to inform the driver
core that we have a runtime dependency to the DSA master interface's
device, and create a device link where that is the supplier and we are
the consumer. Having this device link will make the DSA switch unbind
before the DSA master unbinds, which is enough to avoid the WARN_ON from
rollback_registered_many.
Note that even before the blamed commit, DSA did nothing intelligent
when the master interface got unregistered either. See the discussion
here:
https://lore.kernel.org/netdev/20200505210253.20311-1-f.fainelli@gmail.com/
But this time, at least the WARN_ON is loud enough that the
upper_dev_link commit can be blamed.
The advantage with this approach vs dev_hold(master) in the attached
link is that the latter is not meant for long term reference counting.
With dev_hold, the only thing that will happen is that when the user
attempts an unbind of the DSA master, netdev_wait_allrefs will keep
waiting and waiting, due to DSA keeping the refcount forever. DSA would
not access freed memory corresponding to the master interface, but the
unbind would still result in a freeze. Whereas with device links,
graceful teardown is ensured. It even works with cascaded DSA trees.
$ echo 0000:00:00.2 > /sys/bus/pci/drivers/fsl_enetc/unbind
[ 1818.797546] device swp0 left promiscuous mode
[ 1819.301112] sja1105 spi2.0: Link is Down
[ 1819.307981] DSA: tree 1 torn down
[ 1819.312408] device eno2 left promiscuous mode
[ 1819.656803] mscc_felix 0000:00:00.5: Link is Down
[ 1819.667194] DSA: tree 0 torn down
[ 1819.711557] fsl_enetc 0000:00:00.2 eno2: Link is Down
This approach allows us to keep the DSA framework absolutely unchanged,
and the driver core will just know to unbind us first when the master
goes away - as opposed to the large (and probably impossible) rework
required if attempting to listen for NETDEV_UNREGISTER.
As per the documentation at Documentation/driver-api/device_link.rst,
specifying the DL_FLAG_AUTOREMOVE_CONSUMER flag causes the device link
to be automatically purged when the consumer fails to probe or later
unbinds. So we don't need to keep the consumer_link variable in struct
dsa_switch.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210111230943.3701806-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all port object notifiers were converted to be non-transactional,
we can remove the comments that say otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.
So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.
It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For many drivers, the .port_mdb_prepare callback was not a good opportunity
to avoid any error condition, and they would suppress errors found during
the actual commit phase.
Where a logical separation between the prepare and the commit phase
existed, the function that used to implement the .port_mdb_prepare
callback still exists, but now it is called directly from .port_mdb_add,
which was modified to return an int code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Wallei <linus.walleij@linaro.org> # RTL8366
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the shim introduced in DSA for offloading the bridge ageing time
from switchdev, by first checking whether the ageing time is within the
range limits requested by the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port objects were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
object notifier structures, and converts drivers to not look at this
member.
Where driver conversion is trivial (like in the case of the Marvell
Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is
done in this patch.
Where driver conversion needs more attention (DSA, Mellanox Spectrum),
the conversion is left for subsequent patches and here we only fake the
prepare/commit phases at a lower level, just not in the switchdev
notifier itself.
Where the code has a natural structure that is best left alone as a
preparation and a commit phase (as in the case of the Ocelot switch),
that structure is left in place, just made to not depend upon the
switchdev transactional model.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef78
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b935 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1a ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc2
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduced in commit 37b8da1a3c ("net: dsa: Move FDB add/del
implementation inside DSA") in net/dsa/legacy.c, these functions were
moved again to slave.c as part of commit 2a93c1a365 ("net: dsa: Allow
compiling out legacy support"), before actually deleting net/dsa/slave.c
in 93e86b3bc8 ("net: dsa: Remove legacy probing support"). Along with
that movement there should have been a deletion of the prototypes from
dsa_priv.h, they are not useful.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210108233054.1222278-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This effectively reverts commit 60724d4bae ("net: dsa: Add support for
DSA specific notifiers"). The reason is that since commit 2f1e8ea726
("net: dsa: link interfaces with the DSA master to get rid of lockdep
warnings"), it appears that there is a generic way to achieve the same
purpose. The only user thus far, the Broadcom SYSTEMPORT driver, was
converted to use the generic notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using the NETDEV_CHANGEUPPER notifications, drivers can be aware when
they are enslaved to e.g. a bridge by calling netif_is_bridge_master().
Export this helper from DSA to get the equivalent functionality of
determining whether the upper interface of a CHANGEUPPER notifier is a
DSA switch interface or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is a bit strange to see something as specific as Broadcom SYSTEMPORT
bits in the main DSA include file. Move these away into a separate
header, and have the tagger and the SYSTEMPORT driver include them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some DSA switches (and not only) cannot learn source MAC addresses from
packets injected from the CPU. They only perform hardware address
learning from inbound traffic.
This can be problematic when we have a bridge spanning some DSA switch
ports and some non-DSA ports (which we'll call "foreign interfaces" from
DSA's perspective).
There are 2 classes of problems created by the lack of learning on
CPU-injected traffic:
- excessive flooding, due to the fact that DSA treats those addresses as
unknown
- the risk of stale routes, which can lead to temporary packet loss
To illustrate the second class, consider the following situation, which
is common in production equipment (wireless access points, where there
is a WLAN interface and an Ethernet switch, and these form a single
bridging domain).
AP 1:
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
| ^ ^
| | |
| | |
| Client A Client B
|
|
|
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
AP 2
- br0 of AP 1 will know that Clients A and B are reachable via wlan0
- the hardware fdb of a DSA switch driver today is not kept in sync with
the software entries on other bridge ports, so it will not know that
clients A and B are reachable via the CPU port UNLESS the hardware
switch itself performs SA learning from traffic injected from the CPU.
Nonetheless, a substantial number of switches don't.
- the hardware fdb of the DSA switch on AP 2 may autonomously learn that
Client A and B are reachable through swp0. Therefore, the software br0
of AP 2 also may or may not learn this. In the example we're
illustrating, some Ethernet traffic has been going on, and br0 from AP
2 has indeed learnt that it can reach Client B through swp0.
One of the wireless clients, say Client B, disconnects from AP 1 and
roams to AP 2. The topology now looks like this:
AP 1:
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
| ^
| |
| Client A
|
|
| Client B
| |
| v
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
AP 2
- br0 of AP 1 still knows that Client A is reachable via wlan0 (no change)
- br0 of AP 1 will (possibly) know that Client B has left wlan0. There
are cases where it might never find out though. Either way, DSA today
does not process that notification in any way.
- the hardware FDB of the DSA switch on AP 1 may learn autonomously that
Client B can be reached via swp0, if it receives any packet with
Client 1's source MAC address over Ethernet.
- the hardware FDB of the DSA switch on AP 2 still thinks that Client B
can be reached via swp0. It does not know that it has roamed to wlan0,
because it doesn't perform SA learning from the CPU port.
Now Client A contacts Client B.
AP 1 routes the packet fine towards swp0 and delivers it on the Ethernet
segment.
AP 2 sees a frame on swp0 and its fdb says that the destination is swp0.
Hairpinning is disabled => drop.
This problem comes from the fact that these switches have a 'blind spot'
for addresses coming from software bridging. The generic solution is not
to assume that hardware learning can be enabled somehow, but to listen
to more bridge learning events. It turns out that the bridge driver does
learn in software from all inbound frames, in __br_handle_local_finish.
A proper SWITCHDEV_FDB_ADD_TO_DEVICE notification is emitted for the
addresses serviced by the bridge on 'foreign' interfaces. The software
bridge also does the right thing on migration, by notifying that the old
entry is deleted, so that does not need to be special-cased in DSA. When
it is deleted, we just need to delete our static FDB entry towards the
CPU too, and wait.
The problem is that DSA currently only cares about SWITCHDEV_FDB_ADD_TO_DEVICE
events received on its own interfaces, such as static FDB entries.
Luckily we can change that, and DSA can listen to all switchdev FDB
add/del events in the system and figure out if those events were emitted
by a bridge that spans at least one of DSA's own ports. In case that is
true, DSA will also offload that address towards its own CPU port, in
the eventuality that there might be bridge clients attached to the DSA
switch who want to talk to the station connected to the foreign
interface.
In terms of implementation, we need to keep the fdb_info->added_by_user
check for the case where the switchdev event was targeted directly at a
DSA switch port. But we don't need to look at that flag for snooped
events. So the check is currently too late, we need to move it earlier.
This also simplifies the code a bit, since we avoid uselessly allocating
and freeing switchdev_work.
We could probably do some improvements in the future. For example,
multi-bridge support is rudimentary at the moment. If there are two
bridges spanning a DSA switch's ports, and both of them need to service
the same MAC address, then what will happen is that the migration of one
of those stations will trigger the deletion of the FDB entry from the
CPU port while it is still used by other bridge. That could be improved
with reference counting but is left for another time.
This behavior needs to be enabled at driver level by setting
ds->assisted_learning_on_cpu_port = true. This is because we don't want
to inflict a potential performance penalty (accesses through
MDIO/I2C/SPI are expensive) to hardware that really doesn't need it
because address learning on the CPU port works there.
Reported-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Right now, the following would happen for a switch driver that does not
implement .port_fdb_add or .port_fdb_del.
dsa_slave_switchdev_event returns NOTIFY_OK and schedules:
-> dsa_slave_switchdev_event_work
-> dsa_port_fdb_add
-> dsa_port_notify(DSA_NOTIFIER_FDB_ADD)
-> dsa_switch_fdb_add
-> if (!ds->ops->port_fdb_add) return -EOPNOTSUPP;
-> an error is printed with dev_dbg, and
dsa_fdb_offload_notify(switchdev_work) is not called.
We can avoid scheduling the worker for nothing and say NOTIFY_DONE.
Because we don't call dsa_fdb_offload_notify, the static FDB entry will
remain just in the software bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We'll need to start listening to SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE
events even for interfaces where dsa_slave_dev_check returns false, so
we need that check inside the switch-case statement for SWITCHDEV_FDB_*.
This movement also avoids a useless allocation / free of switchdev_work
on the untreated "default event" case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently DSA doesn't add FDB entries on the CPU port, because it only
does so through switchdev, which is associated with a net_device, and
there are none of those for the CPU port.
But actually FDB addresses on the CPU port have some use cases of their
own, if the switchdev operations are initiated from within the DSA
layer. There is just one problem with the existing code: it passes a
structure in dsa_switchdev_event_work which was retrieved directly from
switchdev, so it contains a net_device. We need to generalize the
contents to something that covers the CPU port as well: the "ds, port"
tuple is fine for that.
Note that the new procedure for notifying the successful FDB offload is
inspired from the rocker model.
Also, nothing was being done if added_by_user was false. Let's check for
that a lot earlier, and don't actually bother to schedule the worker
for nothing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dev_close() call was added in commit c9eb3e0f87 ("net: dsa: Add
support for learning FDB through notification") "to indicate inconsistent
situation" when we could not delete an FDB entry from the port.
bridge fdb del d8:58:d7:00:ca:6d dev swp0 self master
It is a bit drastic and at the same time not helpful if the above fails
to only print with netdev_dbg log level, but on the other hand to bring
the interface down.
So increase the verbosity of the error message, and drop dev_close().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looking for an -EINVAL all over the dsa code could take hours for
inexperienced DSA users.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210106090915.21439-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These warnings become somewhat more informative when they include the
MTU value that could not be set and not just the errno.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201205133944.10182-1-rasmus.villemoes@prevas.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unused and add needed includes. No functional change.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If dsa_switch_ops::port_txtstamp() returns false, clone will be freed
immediately. Shouldn't store a pointer to freed memory.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201119110906.25558-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use a consistent style of one-line/multi-line comments throughout the
file.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethertype DSA encodes exactly the same information in the DSA tag as
the non-ethertype variety. So refactor out the common parts and reuse
them for both protocols.
This is ensures tag parsing and generation is always consistent across
all mv88e6xxx chips.
While we are at it, explicitly deal with all possible CPU codes on
receive, making sure to set offload_fwd_mark as appropriate.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When receiving an IGMP/MLD frame with a TO_CPU tag, the switch has not
performed any forwarding of it. This means that we should not set the
offload_fwd_mark on the skb, in case a software bridge wants it
forwarded.
This is a port of:
1ed9ec9b08 ("dsa: Allow forwarding of redirected IGMP traffic")
Which corrected the issue for chips using EDSA tags, but not for those
using regular DSA tags.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of dsa_slave_priv for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switches rely on unique pvids to ensure port separation in
standalone mode, because they don't have a port forwarding matrix
configurable in hardware. So, setups like a group of 2 uppers with the
same VLAN, swp0.100 and swp1.100, will cause traffic tagged with VLAN
100 to be autonomously forwarded between these switch ports, in spite
of there being no bridge between swp0 and swp1.
These drivers need to prevent this from happening. They need to have
VLAN filtering enabled in standalone mode (so they'll drop frames tagged
with unknown VLANs) and they can only accept an 8021q upper on a port as
long as it isn't installed on any other port too. So give them the
chance to veto bad user requests.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Kurt: Pass info instead of ptr]
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Hirschmann Hellcreek TSN switches have a special tagging protocol for frames
exchanged between the CPU port and the master interface. The format is a one
byte trailer indicating the destination or origin port.
It's quite similar to the Micrel KSZ tagging. That's why the implementation is
based on that code.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: Per Forlin <per.forlin@axis.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
This one is interesting, the DSA tag is 8 bytes on RX and 4 bytes on TX.
Because DSA is unaware of asymmetrical tag lengths, the overhead/needed
headroom is declared as 8 bytes and therefore 4 bytes larger than it
needs to be. If this becomes a problem, and the GSWIP driver can't be
converted to a uniform header length, we might need to make DSA aware of
separate RX/TX overhead values.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Similar to the EtherType DSA tagger, the old Marvell tagger can
transform an 802.1Q header if present into a DSA tag, so there is no
headroom required in that case. But we are ensuring that it exists,
regardless (practically speaking, the headroom must be 4 bytes larger
than it needs to be).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Note that the VLAN code path needs a smaller extra headroom than the
regular EtherType DSA path. That isn't a problem, because this tagger
declares the larger tag length (8 bytes vs 4) as the protocol overhead,
so we are covered in both cases.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: John Crispin <john@phrozen.org>
Cc: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The caller (dsa_slave_xmit) guarantees that the frame length is at least
ETH_ZLEN and that enough memory for tail tagging is available.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The caller (dsa_slave_xmit) guarantees that the frame length is at least
ETH_ZLEN and that enough memory for tail tagging is available.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the moment, taggers are left with the task of ensuring that the skb
headers are writable (which they aren't, if the frames were cloned for
TX timestamping, for flooding by the bridge, etc), and that there is
enough space in the skb data area for the DSA tag to be pushed.
Moreover, the life of tail taggers is even harder, because they need to
ensure that short frames have enough padding, a problem that normal
taggers don't have.
The principle of the DSA framework is that everything except for the
most intimate hardware specifics (like in this case, the actual packing
of the DSA tag bits) should be done inside the core, to avoid having
code paths that are very rarely tested.
So provide a TX reallocation procedure that should cover the known needs
of DSA today.
Note that this patch also gives the network stack a good hint about the
headroom/tailroom it's going to need. Up till now it wasn't doing that.
So the reallocation procedure should really be there only for the
exceptional cases, and for cloned packets which need to be unshared.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Christian Eggers <ceggers@arri.de> # For tail taggers only
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Fixes: 7a6ffe764b ("net: dsa: point out the tail taggers")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201016171603.10587-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplify the code by using new function dev_fetch_sw_netstats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/b6047017-8226-6b7e-a3cd-064e69fdfa27@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the Extraction Frame Header contains a valid classified VLAN, use
that instead of the VLAN header present in the packet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink port regions, via simple
wrappers.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers want to create regions on devlink ports as well as the
devlink device instance, in order to export registers and other tables
per port. To keep all this code together in the drivers, have the
devlink ports registered early, so the setup() method can setup both
device and port devlink regions.
v3:
Remove dp->setup
Move common code out of switch statement.
Fix wrong goto
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a port is unused, still create a devlink port for it, but set the
flavour to unused. This allows us to attach devlink regions to the
port, etc.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are guaranteed that dsa_untag_bridge_pvid() is called after
eth_type_trans() we can utilize __vlan_find_dev_deep_rcu() which will
take care of finding an 802.1Q upper on top of a bridge master.
A common use case, prior to 12a1526d067 ("net: dsa: untag the bridge
pvid from rx skbs") was to configure a bridge 802.1Q upper like this:
ip link add name br0 type bridge vlan_filtering 0
ip link add link br0 name br0.1 type vlan id 1
in order to pop the default_pvid VLAN tag.
With this change we restore that behavior while still allowing the DSA
receive path to automatically pop the VLAN tag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that dsa_untag_bridge_pvid() is called after eth_type_trans() we are
guaranteed that skb->protocol will be set to a correct value, thus
allowing us to avoid calling vlan_eth_hdr().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.
This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 is a bit of a special snowflake, in that not all frames are
transmitted/received in the same way. L2 link-local frames are received
with the source port/switch ID information put in the destination MAC
address. For the rest, a tag_8021q header is used. So only the latter
frames displace the rest of the headers and need to use the generic flow
dissector procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: John Crispin <john@phrozen.org>
Cc: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 Broadcom tags in use, one places the DSA tag before the
Ethernet destination MAC address, and the other before the EtherType.
Nonetheless, both displace the rest of the headers, so this tagger can
use the generic flow dissector procedure which accounts for that.
The ASCII art drawing is a good reference though, so keep it but move it
somewhere else.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Tell that to the DSA core, since this makes a difference for the flow
dissector. Most switches break the parsing of frame headers, but these
ones don't, so no flow dissector adjustment needs to be done for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no tagger that returns anything other than zero, so just change
the return type appropriately.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PTP is broken when ports are in standalone mode (the tagger
keeps printing this message):
sja1105 spi0.1: Expected meta frame, is 01-80-c2-00-00-0e in the DSA master multicast filter?
Sure, one might say "simply add 01-80-c2-00-00-0e to the master's RX
filter" but things become more complicated because:
- Actually all frames in the 01-80-c2-xx-xx-xx and 01-1b-19-xx-xx-xx
range are trapped to the CPU automatically
- The switch mangles bytes 3 and 4 of the MAC address via the incl_srcpt
("include source port [in the DMAC]") option, which is how source port
and switch id identification is done for link-local traffic on RX. But
this means that an address installed to the RX filter would, at the
end of the day, not correspond to the final address seen by the DSA
master.
Assume RX filtering lists on DSA masters are typically too small to
include all necessary addresses for PTP to work properly on sja1105, and
just request promiscuous mode unconditionally.
Just an example:
Assuming the following addresses are trapped to the CPU:
01-80-c2-00-00-00 to 01-80-c2-00-00-ff
01-1b-19-00-00-00 to 01-1b-19-00-00-ff
These are 512 addresses.
Now let's say this is a board with 3 switches, and 4 ports per switch.
The 512 addresses become 6144 addresses that must be managed by the DSA
master's RX filtering lists.
This may be refined in the future, but for now, it is simply not worth
it to add the additional addresses to the master's RX filter, so simply
request it to become promiscuous as soon as the driver probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA assumes that taggers don't mess with the destination MAC
address of the frames on RX. That is not always the case. Some DSA
headers are placed before the Ethernet header (ocelot), and others
simply mangle random bytes from the destination MAC address (sja1105
with its incl_srcpt option).
Currently the DSA master goes to promiscuous mode automatically when the
slave devices go too (such as when enslaved to a bridge), but in
standalone mode this is a problem that needs to be dealt with.
So give drivers the possibility to signal that their tagging protocol
will get randomly dropped otherwise, and let DSA deal with fixing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the B53 driver to support VLANs while not filtering. This
requires us to enable VLAN globally within the switch upon driver
initial configuration (dev->vlan_enabled).
We also need to remove the code that dealt with PVID re-configuration in
b53_vlan_filtering() since that function worked under the assumption
that it would only be called to make a bridge VLAN filtering, or not
filtering, and we would attempt to move the port's PVID accordingly.
Now that VLANs are programmed all the time, even in the case of a
non-VLAN filtering bridge, we would be programming a default_pvid for
the bridged switch ports.
We need the DSA receive path to pop the VLAN tag if it is the bridge's
default_pvid because the CPU port is always programmed tagged in the
programmed VLANs. In order to do so we utilize the
dsa_untag_bridge_pvid() helper introduced in the commit before within
net/dsa/tag_brcm.c.
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge untags VLANs present in its VLAN groups in
__allowed_ingress() only when VLAN filtering is enabled.
But when a skb is seen on the RX path as tagged with the bridge's pvid,
and that bridge has vlan_filtering=0, and there isn't any 8021q upper
with that VLAN either, then we have a problem. The bridge will not untag
it (since it is supposed to remain VLAN-unaware), and pvid-tagged
communication will be broken.
There are 2 situations where we can end up like that:
1. When installing a pvid in egress-tagged mode, like this:
ip link add dev br0 type bridge vlan_filtering 0
ip link set swp0 master br0
bridge vlan del dev swp0 vid 1
bridge vlan add dev swp0 vid 1 pvid
This happens because DSA configures the VLAN membership of the CPU port
using the same flags as swp0 (in this case "pvid and not untagged"), in
an attempt to copy the frame as-is from ingress to the CPU.
However, in this case, the packet may arrive untagged on ingress, it
will be pvid-tagged by the ingress port, and will be sent as
egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN
tag where there was none to speak of on ingress.
When vlan_filtering is 1, this is not a problem, as stated in the first
paragraph, because __allowed_ingress() will pop it. But currently, when
vlan_filtering is 0 and we have such a VLAN configuration, we need an
8021q upper (br0.1) to be able to ping over that VLAN, which is not
symmetrical with the vlan_filtering=1 case, and therefore, confusing for
users.
Basically what DSA attempts to do is simply an approximation: try to
copy the skb with (or without) the same VLAN all the way up to the CPU.
But DSA drivers treat CPU port VLAN membership in various ways (which is
a good segue into situation 2). And some of those drivers simply tell
the CPU port to copy the frame unmodified, which is the golden standard
when it comes to VLAN processing (therefore, any driver which can
configure the hardware to do that, should do that, and discard the VLAN
flags requested by DSA on the CPU port).
2. Some DSA drivers always configure the CPU port as egress-tagged, in
an attempt to recover the classified VLAN from the skb. These drivers
cannot work at all with untagged traffic when bridged in
vlan_filtering=0 mode. And they can't go for the easy "just keep the
pvid as egress-untagged towards the CPU" route, because each front port
can have its own pvid, and that might require conflicting VLAN
membership settings on the CPU port (swp1 is pvid for VID 1 and
egress-tagged for VID 2; swp2 is egress-taggeed for VID 1 and pvid for
VID 2; with this simplistic approach, the CPU port, which is really a
separate hardware entity and has its own VLAN membership settings, would
end up being egress-untagged in both VID 1 and VID 2, therefore losing
the VLAN tags of ingress traffic).
So the only thing we can do is to create a helper function for resolving
the problematic case (that is, a function which untags the bridge pvid
when that is in vlan_filtering=0 mode), which taggers in need should
call. It isn't called from the generic DSA receive path because there
are drivers that fall neither in the first nor second category.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether there is any hwaccel VLAN tag on RX, and if there is,
treat it as the tag_8021q header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole purpose of tag_8021q is to send VLAN-tagged traffic to the
CPU, from which the driver can decode the source port and switch id.
Currently this only works if the VLAN filtering on the master is
disabled. Change that by explicitly adding code to tag_8021q.c to add
the VLANs corresponding to the tags to the filter of the master
interface.
Because we now need to call vlan_vid_add, then we also need to hold the
RTNL mutex. Propagate that requirement to the callers of dsa_8021q_setup
and modify the existing call sites as appropriate. Note that one call
path, sja1105_best_effort_vlan_filtering_set -> sja1105_vlan_filtering
-> sja1105_setup_8021q_tagging, was already holding this lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most DSA switch tags shift the EtherType to the right, causing the
master to not parse the VLAN as VLAN.
However, not all switches do that (example: tail tags, tag_8021q etc),
and if the DSA master has "rx-vlan-filter: on" in ethtool -k, then we
have a problem.
Therefore, we could populate the VLAN table of the master, just in case
(for some switches it will not make a difference), so that network I/O
can work even with a VLAN filtering master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge has VLAN awareness disabled there isn't any duplication
of functionality, since the bridge does not process VLAN. Don't deny
adding 8021q uppers to DSA switch ports in that case. The switch is
supposed to simply pass traffic leaving the VLAN tag as-is, and the
stack will happily strip the VLAN tag for all 8021q uppers that exist.
We need to ensure that there are no 8021q uppers when the user attempts
to enable bridge vlan_filtering.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic beats me a little bit. The comment that "bridge skips
-EOPNOTSUPP, so skip the prepare phase" was introduced in commit
fb2dabad69 ("net: dsa: support VLAN filtering switchdev attr").
I'm not sure:
(a) ok, the bridge skips -EOPNOTSUPP, but, so what, where are we
returning -EOPNOTSUPP?
(b) even if we are, and I'm just not seeing it, what is the causality
relationship between the bridge skipping -EOPNOTSUPP and DSA
skipping the prepare phase, and just returning zero?
One thing is certain beyond doubt though, and that is that DSA currently
refuses VLAN filtering from the "commit" phase instead of "prepare", and
that this is not a good thing:
ip link add br0 type bridge
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br1
[ 3790.379389] 001: sja1105 spi0.1: VLAN filtering is a global setting
[ 3790.379399] 001: ------------[ cut here ]------------
[ 3790.379403] 001: WARNING: CPU: 1 PID: 515 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 3790.379420] 001: swp3: Commit of attribute (id=6) failed.
[ 3790.379533] 001: [<c11ff588>] (switchdev_port_attr_set_now) from [<c11b62e4>] (nbp_vlan_init+0x84/0x148)
[ 3790.379544] 001: [<c11b62e4>] (nbp_vlan_init) from [<c11a2ff0>] (br_add_if+0x514/0x670)
[ 3790.379554] 001: [<c11a2ff0>] (br_add_if) from [<c1031b5c>] (do_setlink+0x38c/0xab0)
[ 3790.379565] 001: [<c1031b5c>] (do_setlink) from [<c1036fe8>] (__rtnl_newlink+0x44c/0x748)
[ 3790.379573] 001: [<c1036fe8>] (__rtnl_newlink) from [<c1037328>] (rtnl_newlink+0x44/0x60)
[ 3790.379580] 001: [<c1037328>] (rtnl_newlink) from [<c10315fc>] (rtnetlink_rcv_msg+0x124/0x2f8)
[ 3790.379590] 001: [<c10315fc>] (rtnetlink_rcv_msg) from [<c10926b8>] (netlink_rcv_skb+0xb8/0x110)
[ 3790.379806] 001: ---[ end trace 0000000000000002 ]---
[ 3790.379819] 001: sja1105 spi0.1 swp3: failed to initialize vlan filtering on this port
So move the current logic that may fail (except ds->ops->port_vlan_filtering,
that is way harder) into the prepare stage of the switchdev transaction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is checking for the following order of operations, and makes sure
to deny that configuration:
ip link add link swp2 name swp2.100 type vlan id 100
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan add dev swp2 vid 100
Instead of using vlan_for_each(), which looks at the VLAN filters
installed with vlan_vid_add(), just track the 8021q uppers. This has the
advantage of freeing up the vlan_vid_add() call for actual VLAN
filtering.
There is another change in this patch. The check is moved in slave.c,
from switch.c. I don't think it makes sense to have this 8021q upper
check for each switch port that gets notified of that VLAN addition
(these include DSA links and CPU ports, we know those can't have 8021q
uppers because they don't have a net_device registered for them), so
just do it in slave.c, for that one slave interface.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA tries to prevent having a VLAN added by a bridge and by an 802.1Q
upper at the same time. It does that by checking the VID in
.ndo_vlan_rx_add_vid(), since that's something that the 8021q module
calls, via vlan_vid_add(). When a VLAN matches in both subsystems, this
check returns -EBUSY.
However the vlan_vid_add() function isn't specific to the 8021q module
in any way at all. It is simply the kernel's way to tell an interface to
add a VLAN to its RX filter and not drop that VLAN. So there's no reason
to return -EBUSY when somebody tries to call vlan_vid_add() for a VLAN
that was installed by the bridge. The proper behavior is to accept that
configuration.
So what's wrong is how DSA checks that it has an 8021q upper. It should
look at the actual uppers for that, not just assume that the 8021q
module was somewhere in the call stack of .ndo_vlan_rx_add_vid().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll be adding a new check in the PRECHANGEUPPER notifier, where we'll
need to check some VLAN uppers. It is hard to do that when there is
already a function named dsa_slave_upper_vlan_check. So rename this one.
Not to mention that this function probably shouldn't have started with
"dsa_slave_" in the first place, since the struct net_device argument
isn't a DSA slave, but an 8021q upper of one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There doesn't seem to be any strong technical reason for doing it this
way, but we'll be adding more checks for invalid upper device
configurations, and it will be easier to have them all grouped under
PRECHANGEUPPER.
Tested that it still works:
ip link set br0 type bridge vlan_filtering 1
ip link add link swp2 name swp2.100 type vlan id 100
ip link set swp2.100 master br0
[ 20.321312] br0: port 5(swp2.100) entered blocking state
[ 20.326711] br0: port 5(swp2.100) entered disabled state
Error: dsa_core: Cannot enslave VLAN device into VLAN aware bridge.
[ 20.346549] br0: port 5(swp2.100) entered blocking state
[ 20.351957] br0: port 5(swp2.100) entered disabled state
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the DSA drivers to implement the devlink call to get info info,
e.g. driver name, firmware version, ASIC ID, etc.
v2:
Combine declaration and the assignment on a single line.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink regions, via simple wrappers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given a devlink instance, return the dsa switch it is associated to.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 314f76d7a6.
Citing that commit message, the call graph was:
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Now that tag_8021q has its own ops structure, it no longer relies on
dsa_port_vid_add, and therefore on the dsa_switch_ops to install its
VLANs.
So dsa_port_vid_add now only has one single caller. So we can simplify
the call graph to what it was before, aka:
dsa_slave_vlan_rx_add_vid dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on another tag_8021q driver implementation, some things
became apparent:
- It is not mandatory for a DSA driver to offload the tag_8021q VLANs by
using the VLAN table per se. For example, it can add custom TCAM rules
that simply encapsulate RX traffic, and redirect & decapsulate rules
for TX traffic. For such a driver, it makes no sense to receive the
tag_8021q configuration through the same callback as it receives the
VLAN configuration from the bridge and the 8021q modules.
- Currently, sja1105 (the only tag_8021q user) sets a
priv->expect_dsa_8021q variable to distinguish between the bridge
calling, and tag_8021q calling. That can be improved, to say the
least.
- The crosschip bridging operations are, in fact, stateful already. The
list of crosschip_links must be kept by the caller and passed to the
relevant tag_8021q functions.
So it would be nice if the tag_8021q configuration was more
self-contained. This patch attempts to do that.
Create a struct dsa_8021q_context which encapsulates a struct
dsa_switch, and has 2 function pointers for adding and deleting a VLAN.
These will replace the previous channel to the driver, which was through
the .port_vlan_add and .port_vlan_del callbacks of dsa_switch_ops.
Also put the list of crosschip_links into this dsa_8021q_context.
Drivers that don't support cross-chip bridging can simply omit to
initialize this list, as long as they dont call any cross-chip function.
The sja1105_vlan_add and sja1105_vlan_del functions are refactored into
a smaller sja1105_vlan_add_one, which now has 2 entry points:
- sja1105_vlan_add, from struct dsa_switch_ops
- sja1105_dsa_8021q_vlan_add, from the tag_8021q ops
But even this change is fairly trivial. It just reflects the fact that
for sja1105, the VLANs from these 2 channels end up in the same hardware
table. However that is not necessarily true in the general sense (and
that's the reason for making this change).
The rest of the patch is mostly plain refactoring of "ds" -> "ctx". The
dsa_8021q_context structure needs to be propagated because adding a VLAN
is now done through the ops function pointers inside of it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in calling dsa_port_setup_8021q_tagging for each
individual port. Additionally, it will become more difficult to do that
when we'll have a context structure to tag_8021q (next patch). So
refactor this now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 845e0ebb44 ("net: change addr_list_lock back to static
key"), cascaded DSA setups (DSA switch port as DSA master for another
DSA switch port) are emitting this lockdep warning:
============================================
WARNING: possible recursive locking detected
5.8.0-rc1-00133-g923e4b5032dd-dirty #208 Not tainted
--------------------------------------------
dhcpcd/323 is trying to acquire lock:
ffff000066dd4268 (&dsa_master_addr_list_lock_key/1){+...}-{2:2}, at: dev_mc_sync+0x44/0x90
but task is already holding lock:
ffff00006608c268 (&dsa_master_addr_list_lock_key/1){+...}-{2:2}, at: dev_mc_sync+0x44/0x90
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dsa_master_addr_list_lock_key/1);
lock(&dsa_master_addr_list_lock_key/1);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by dhcpcd/323:
#0: ffffdbd1381dda18 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x24/0x30
#1: ffff00006614b268 (_xmit_ETHER){+...}-{2:2}, at: dev_set_rx_mode+0x28/0x48
#2: ffff00006608c268 (&dsa_master_addr_list_lock_key/1){+...}-{2:2}, at: dev_mc_sync+0x44/0x90
stack backtrace:
Call trace:
dump_backtrace+0x0/0x1e0
show_stack+0x20/0x30
dump_stack+0xec/0x158
__lock_acquire+0xca0/0x2398
lock_acquire+0xe8/0x440
_raw_spin_lock_nested+0x64/0x90
dev_mc_sync+0x44/0x90
dsa_slave_set_rx_mode+0x34/0x50
__dev_set_rx_mode+0x60/0xa0
dev_mc_sync+0x84/0x90
dsa_slave_set_rx_mode+0x34/0x50
__dev_set_rx_mode+0x60/0xa0
dev_set_rx_mode+0x30/0x48
__dev_open+0x10c/0x180
__dev_change_flags+0x170/0x1c8
dev_change_flags+0x2c/0x70
devinet_ioctl+0x774/0x878
inet_ioctl+0x348/0x3b0
sock_do_ioctl+0x50/0x310
sock_ioctl+0x1f8/0x580
ksys_ioctl+0xb0/0xf0
__arm64_sys_ioctl+0x28/0x38
el0_svc_common.constprop.0+0x7c/0x180
do_el0_svc+0x2c/0x98
el0_sync_handler+0x9c/0x1b8
el0_sync+0x158/0x180
Since DSA never made use of the netdev API for describing links between
upper devices and lower devices, the dev->lower_level value of a DSA
switch interface would be 1, which would warn when it is a DSA master.
We can use netdev_upper_dev_link() to describe the relationship between
a DSA slave and a DSA master. To be precise, a DSA "slave" (switch port)
is an "upper" to a DSA "master" (host port). The relationship is "many
uppers to one lower", like in the case of VLAN. So, for that reason, we
use the same function as VLAN uses.
There might be a chance that somebody will try to take hold of this
interface and use it immediately after register_netdev() and before
netdev_upper_dev_link(). To avoid that, we do the registration and
linkage while holding the RTNL, and we use the RTNL-locked cousin of
register_netdev(), which is register_netdevice().
Since this warning was not there when lockdep was using dynamic keys for
addr_list_lock, we are blaming the lockdep patch itself. The network
stack _has_ been using static lockdep keys before, and it _is_ likely
that stacked DSA setups have been triggering these lockdep warnings
since forever, however I can't test very old kernels on this particular
stacked DSA setup, to ensure I'm not in fact introducing regressions.
Fixes: 845e0ebb44 ("net: change addr_list_lock back to static key")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 72579e14a1 ("net: dsa: don't fail to probe if we couldn't set
the MTU") changed, for some reason, the "err && err != -EOPNOTSUPP"
check into a simple "err". This causes the MTU warning to be printed
even for drivers that don't have the MTU operations implemented.
Fix that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
slave_dev->name is only populated at this stage if it was specified
through a label in the device tree. However that is not mandatory.
When it isn't, the error message looks like this:
[ 5.037057] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
[ 5.044672] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
[ 5.052275] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
[ 5.059877] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
which is especially confusing since the error gets printed on behalf of
the DSA master (fsl_enetc in this case).
Printing an error message that contains a valid reference to the DSA
port's name is difficult at this point in the initialization stage, so
at least we should print some info that is more reliable, even if less
user-friendly. That may be the driver name and the hardware port index.
After this change, the error is printed as:
[ 6.051587] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 0
[ 6.061192] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 1
[ 6.070765] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 2
[ 6.080324] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 3
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
