Steinar reported reallocations of skb->head with IPv6, leading to
a warning in skb_try_coalesce()
It turns out iwl3945 has several problems :
1) skb->truesize is underestimated.
We really consume PAGE_SIZE bytes for a fragment,
not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Stewart <pstew@google.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd9c46408f.
With "iwl{4965,3495): workaround for firmware frame tx rejection"
patches we can enable IEEE80211_HW_REPORTS_TX_ACK_STATUS again.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add functions that will stop/wake all queues. Make them safe
regarding multiple calls and when some ac are stopped/woke
independently.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to return a negative error code in the il3945_hw_set_hw_params() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix build error for il_pm_ops if CONFIG_PM is set
but CONFIG_PM_SLEEP is not set.
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined!
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EXPORT_SYMBOL and inline directives are contradictory to each other.
The patch fixes this inconsistency.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 and the Intel drivers all define crypto
constants, move them to ieee80211.h instead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jake reported that since commit 1672c0e319
"mac80211: start auth/assoc timeout on frame status", he is unable to
connect to his AP, which is configured to use passive channel.
After switch to passive channel 4965 firmware drops any TX packet until
it receives beacon. Before commit 1672c0e3 we waited on channel and
retransmit packet after 200ms, that makes we receive beacon on the
meantime and association process succeed. New mac80211 behaviour cause
that any ASSOC frame fail immediately on iwl4965 and we can not
associate.
This patch restore old mac80211 behaviour for iwl4965, by removing
IEEE80211_HW_REPORTS_TX_ACK_STATUS feature. This feature will be
added again to iwl4965 driver, when different, more complex
workaround for this firmware issue, will be added to the driver.
Cc: stable@vger.kernel.org # 3.9
Bisected-by: Jake Edge <jake@lwn.net>
Reported-and-tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
il4965_rs_initialize_lq checks to see if sta is null, however, before that
check il4965_rs_use_green dereferences sta when intializing use_green.
Avoid a potential null pointer dereference error by only calling
il4965_rs_use_green after we are sure sta is not null.
Smatch analysis:
drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn:
variable dereferenced before check 'sta' (see line 2155)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/net/wireless/iwlegacy/common.c:4894:1: warning: 'il_pci_suspend' defined but not used [-Wunused-function]
drivers/net/wireless/iwlegacy/common.c:4912:1: warning: 'il_pci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull to get the thermal netlink multicast group name fix, otherwise
the assertion added in net-next to netlink to detect that kind of bug
makes systems unbootable for some folks.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions and tables static. Make ops table
Mark 3945 ops as read_mostly.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the sequence number arithmetic code from mac80211 to
ieee80211.h so others can use it. Also rename the functions
from _seq to _sn, they operate on the sequence number, not
the sequence_control field.
Also move macros to convert the sequence control to/from
the sequence number value from various drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch check output of pci_map_single() calls. I missed them on
my previous patch "iwlegacy: check for dma mapping errors", which
fixed only pci_map_page() calls.
To handle remaining possible dma mappings errors, we need to rearrange
ilXXXX_tx_skb() and il_enqueue_hcmd() functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed-up drivers/net/wireless/iwlwifi/mvm/mac80211.c to change change
IEEE80211_HW_NEED_DTIM_PERIOD to IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
as requested by Johannes Berg. -- JWL
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on "iwlwifi: report A-MPDU status".
(12bf6f45d1)
Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.
To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.
Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix:
drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’:
drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but
not used [-Wunused-but-set-variable]
seen when building allmodconfig on x86_64 with W=1 by removing the unused
variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on "iwlwifi: fix antenna bitmask".
(362b0563b2)
Like the new iwlagn devices, the old 4965N device only
supports a maximum of three antennas. Hence only three
bits are used, the fourth bit is likely the A-MPDU
indicator.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete successive tests to the same location. This looks like simple code
duplication.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
