Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.
These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).
In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.
When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.
There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The 14nm DSI PHY on 8x96 (called PHY v2 downstream) requires a different
set of calculations for computing D-PHY timing params. Create a
timing_calc_v2 func for the newer v2 PHYs.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since DSI PHY has been a separate platform device, it should not
depend on the resources in host to be functional. This change is
to trigger PHY operations in manager, instead of host, so that
host and PHY can be completely separated.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For some new types of DSI PHY, more settings depend on
use cases controlled by DSI manager. This change allows
DSI manager to setup PHY with a use case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host is required to configure more timings calculated
in PHY. By introducing a shared structure, this change allows
more timing information passed from PHY to host.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.
The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host and PHY driver currently expects the DT bindings to provide
custom properties "qcom,dsi-host-index" and "qcom,dsi-phy-index" so that
the driver can identify which DSI instance it is.
The binding isn't acceptable, but the driver still needs to figure out
what its instance id. This is now done by storing the mmio starting
addresses for each DSI instance in every SoC version in the driver. The
driver then identifies the index number by trying to match the stored
address with comparing the resource start address we get from DT.
We don't have compatible strings for DSI PHY on each SoC, but only the
DSI PHY type. We only support one SoC version for each PHY type, so we
get away doing the same thing above for the PHY driver. We can revisit
this when we support two SoCs with the same DSI PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
