The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct vio_driver::remove() return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea.
Note there are two nominally different implementations for a vio bus:
one in arch/sparc/kernel/vio.c and the other in
arch/powerpc/platforms/pseries/vio.c. This patch only adapts the powerpc
one.
Before this patch for a device that was bound to a driver without a
remove callback vio_cmo_bus_remove(viodev) wasn't called. As the device
core still considers the device unbound after vio_bus_remove() returns
calling this unconditionally is the consistent behaviour which is
implemented here.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mpe: Drop unneeded hvcs_remove() forward declaration, squash in
change from sfr to drop ibmvnic_remove() forward declaration]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210225221834.160083-1-uwe@kleine-koenig.org
When TPM 2.0 trusted keys code was moved to the trusted keys subsystem,
the operations were unwrapped from tpm_try_get_ops() and tpm_put_ops(),
which are used to take temporarily the ownership of the TPM chip. The
ownership is only taken inside tpm_send(), but this is not sufficient,
as in the key load TPM2_CC_LOAD, TPM2_CC_UNSEAL and TPM2_FLUSH_CONTEXT
need to be done as a one single atom.
Take the TPM chip ownership before sending anything with
tpm_try_get_ops() and tpm_put_ops(), and use tpm_transmit_cmd() to send
TPM commands instead of tpm_send(), reverting back to the old behaviour.
Fixes: 2e19e10131 ("KEYS: trusted: Move TPM2 trusted keys code")
Reported-by: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org
Cc: David Howells <dhowells@redhat.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The only usage of ppi_attr_grp is to put its address in an array of
pointers to const struct attribute_group. Make it const to allow the
compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Create sysfs per hash groups with 24 PCR files in them one group,
named pcr-<hash>, for each agile hash of the TPM. The files are
plugged in to a PCR read function which is TPM version agnostic, so
this works also for TPM 1.2 but the hash is only sha1 in that case.
Note: the macros used to create the hashes emit spurious checkpatch
warnings. Do not try to "fix" them as checkpatch recommends, otherwise
they'll break.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Never used since it was added.
Fixes: 9e1b74a63f ("tpm: add support for nonblocking operation")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-integrity@vger.kernel.org
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Philip Tricca <philip.b.tricca@intel.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Add TPM 2.0 compatible I2C interface for chips with cr50 firmware.
The firmware running on the currently supported H1 MCU requires a
special driver to handle its specific protocol, and this makes it
unsuitable to use tpm_tis_core_* and instead it must implement the
underlying TPM protocol similar to the other I2C TPM drivers.
- All 4 bytes of status register must be read/written at once.
- FIFO and burst count is limited to 63 and must be drained by AP.
- Provides an interrupt to indicate when read response data is ready
and when the TPM is finished processing write data.
This driver is based on the existing infineon I2C TPM driver, which
most closely matches the cr50 i2c protocol behavior.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Tested-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The current release locality code seems to be based on the
misunderstanding that the TPM interrupts when a locality is released:
it doesn't, only when the locality is acquired.
Furthermore, there seems to be no point in waiting for the locality to
be released. All it does is penalize the last TPM user. However, if
there's no next TPM user, this is a pointless wait and if there is a
next TPM user, they'll pay the penalty waiting for the new locality
(or possibly not if it's the same as the old locality).
Fix the code by making release_locality as simple write to release
with no waiting for completion.
Cc: stable@ger.kernel.org
Fixes: 33bafe9082 ("tpm_tis: verify locality released before returning from release_locality")
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The TPM TIS specification says the TPM signals the acquisition of locality
when the TMP_ACCESS_REQUEST_USE bit goes to one *and* the
TPM_ACCESS_REQUEST_USE bit goes to zero. Currently we only check the
former not the latter, so check both. Adding the check on
TPM_ACCESS_REQUEST_USE should fix the case where the locality is
re-requested before the TPM has released it. In this case the locality may
get released briefly before it is reacquired, which causes all sorts of
problems. However, with the added check, TPM_ACCESS_REQUEST_USE should
remain 1 until the second request for the locality is granted.
Cc: stable@ger.kernel.org
Fixes: 27084efee0 ("[PATCH] tpm: driver for next generation TPM chips")
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Mimic the pre-existing ACPI and Device Tree event log behavior by not
creating the binary_bios_measurements file when the EFI TPM event log is
empty.
This fixes the following NULL pointer dereference that can occur when
reading /sys/kernel/security/tpm0/binary_bios_measurements after the
kernel received an empty event log from the firmware:
BUG: kernel NULL pointer dereference, address: 000000000000002c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 3932 Comm: fwupdtpmevlog Not tainted 5.9.0-00003-g629990edad62 #17
Hardware name: LENOVO 20LCS03L00/20LCS03L00, BIOS N27ET38W (1.24 ) 11/28/2019
RIP: 0010:tpm2_bios_measurements_start+0x3a/0x550
Code: 54 53 48 83 ec 68 48 8b 57 70 48 8b 1e 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 48 8b 82 c0 06 00 00 48 8b 8a c8 06 00 00 <44> 8b 60 1c 48 89 4d a0 4c 89 e2 49 83 c4 20 48 83 fb 00 75 2a 49
RSP: 0018:ffffa9c901203db0 EFLAGS: 00010246
RAX: 0000000000000010 RBX: 0000000000000000 RCX: 0000000000000010
RDX: ffff8ba1eb99c000 RSI: ffff8ba1e4ce8280 RDI: ffff8ba1e4ce8258
RBP: ffffa9c901203e40 R08: ffffa9c901203dd8 R09: ffff8ba1ec443300
R10: ffffa9c901203e50 R11: 0000000000000000 R12: ffff8ba1e4ce8280
R13: ffffa9c901203ef0 R14: ffffa9c901203ef0 R15: ffff8ba1e4ce8258
FS: 00007f6595460880(0000) GS:ffff8ba1ef880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000002c CR3: 00000007d8d18003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? __kmalloc_node+0x113/0x320
? kvmalloc_node+0x31/0x80
seq_read+0x94/0x420
vfs_read+0xa7/0x190
ksys_read+0xa7/0xe0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In this situation, the bios_event_log pointer in the tpm_bios_log struct
was not NULL but was equal to the ZERO_SIZE_PTR (0x10) value. This was
due to the following kmemdup() in tpm_read_log_efi():
int tpm_read_log_efi(struct tpm_chip *chip)
{
...
/* malloc EventLog space */
log->bios_event_log = kmemdup(log_tbl->log, log_size, GFP_KERNEL);
if (!log->bios_event_log) {
ret = -ENOMEM;
goto out;
}
...
}
When log_size is zero, due to an empty event log from firmware,
ZERO_SIZE_PTR is returned from kmemdup(). Upon a read of the
binary_bios_measurements file, the tpm2_bios_measurements_start()
function does not perform a ZERO_OR_NULL_PTR() check on the
bios_event_log pointer before dereferencing it.
Rather than add a ZERO_OR_NULL_PTR() check in functions that make use of
the bios_event_log pointer, simply avoid creating the
binary_bios_measurements_file as is done in other event log retrieval
backends.
Explicitly ignore all of the events in the final event log when the main
event log is empty. The list of events in the final event log cannot be
accurately parsed without referring to the first event in the main event
log (the event log header) so the final event log is useless in such a
situation.
Fixes: 58cc1e4faf ("tpm: parse TPM event logs based on EFI table")
Link: https://lore.kernel.org/linux-integrity/E1FDCCCB-CA51-4AEE-AC83-9CDE995EAE52@canonical.com/
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Reported-by: Mimi Zohar <zohar@linux.ibm.com>
Cc: Thiébaud Weksteen <tweek@google.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
There is a misconfiguration in the bios of the gpio pin used for the
interrupt in the T490s. When interrupts are enabled in the tpm_tis
driver code this results in an interrupt storm. This was initially
reported when we attempted to enable the interrupt code in the tpm_tis
driver, which previously wasn't setting a flag to enable it. Due to
the reports of the interrupt storm that code was reverted and we went back
to polling instead of using interrupts. Now that we know the T490s problem
is a firmware issue, add code to check if the system is a T490s and
disable interrupts if that is the case. This will allow us to enable
interrupts for everyone else. If the user has a fixed bios they can
force the enabling of interrupts with tpm_tis.interrupts=1 on the
kernel command line.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Some TIS based TPMs can return 0xff to status reads if the locality
hasn't been properly requested. Detect this condition by checking the
bits that the TIS spec specifies must return zero are clear and return
zero in that case. Also drop a warning so the problem can be
identified in the calling path and fixed (usually a missing
try_get_ops()).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
When fitted, the SynQuacer platform exposes its SPI TPM via a MMIO
window that is backed by the SPI command sequencer in the SPI bus
controller. This arrangement has the limitation that only byte size
accesses are supported, and so we'll need to provide a separate module
that take this into account.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
In case a TPM2 is attached, search for a TPM2 ACPI table when trying
to get the event log from ACPI. If one is found, use it to get the
start and length of the log area. This allows non-UEFI systems, such
as SeaBIOS, to pass an event log when using a TPM2.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org
Reported-by: Stefan Berger <stefanb@linux.ibm.com>
Fixes: 745b361e98 ("tpm: infrastructure for TPM spaces")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Probes drivers on the OP-TEE bus in two steps. First for drivers which
do not depend on tee-supplicant. After tee-supplicant has been started
probe the devices which do depend on tee-supplicant.
Also introduces driver which uses an OP-TEE based fTPM Trusted
Application depends on tee-supplicant NV RAM implementation based on
RPMB secure storage.
-----BEGIN PGP SIGNATURE-----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=PDtV
-----END PGP SIGNATURE-----
Merge tag 'optee-bus-for-v5.9' of git://git.linaro.org/people/jens.wiklander/linux-tee into arm/drivers
Enable multi-stage OP-TEE bus enumeration
Probes drivers on the OP-TEE bus in two steps. First for drivers which
do not depend on tee-supplicant. After tee-supplicant has been started
probe the devices which do depend on tee-supplicant.
Also introduces driver which uses an OP-TEE based fTPM Trusted
Application depends on tee-supplicant NV RAM implementation based on
RPMB secure storage.
* tag 'optee-bus-for-v5.9' of git://git.linaro.org/people/jens.wiklander/linux-tee:
tpm_ftpm_tee: register driver on TEE bus
optee: enable support for multi-stage bus enumeration
optee: use uuid for sysfs driver entry
Link: https://lore.kernel.org/r/20200710085230.GA1312913@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OP-TEE based fTPM Trusted Application depends on tee-supplicant to
provide NV RAM implementation based on RPMB secure storage. So this
dependency can be resolved via TEE bus where we only invoke fTPM
driver probe once fTPM device is registered on the bus which is only
true after the tee-supplicant is up and running. Additionally, TEE bus
provides auto device enumeration.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Suggested-by: Sumit Garg <sumit.garg@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Removing IFX0102 from tpm_tis was not a right move because both tpm_tis
and tpm_infineon use the same device ID. Revert the commit and add a
remark about a bug caused by commit 93e1b7d42e ("[PATCH] tpm: add HID
module parameter").
Fixes: e918e57041 ("tpm_tis: Remove the HID IFX0102")
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acer C720 running Linux v5.3 reports this in klog:
tpm_tis: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis tpm_tis: Could not get TPM timeouts and durations
tpm_tis 00:08: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis 00:08: Could not get TPM timeouts and durations
ima: No TPM chip found, activating TPM-bypass!
tpm_inf_pnp 00:08: Found TPM with ID IFX0102
% git --no-pager grep IFX0102 drivers/char/tpm
drivers/char/tpm/tpm_infineon.c: {"IFX0102", 0},
drivers/char/tpm/tpm_tis.c: {"IFX0102", 0}, /* Infineon */
Obviously IFX0102 was added to the HID table for the TCG TIS driver by
mistake.
Fixes: 93e1b7d42e ("[PATCH] tpm: add HID module parameter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203877
Cc: stable@vger.kernel.org
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Reported-by: Ferry Toth: <ferry.toth@elsinga.info>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
On a Chromebook I'm working on I noticed a big (~1 second) delay
during bootup where nothing was happening. Right around this big
delay there were messages about the TPM:
[ 2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2
[ 3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ...
I put a few printouts in and saw that tpm_tis_spi_init() (specifically
tpm_chip_register() in that function) was taking the lion's share of
this time, though ~115 ms of the time was in cr50_print_fw_version().
Let's make a one-line change to prefer async probe for tpm_tis_spi.
There's no reason we need to block other drivers from probing while we
load.
NOTES:
* It's possible that other hardware runs through the init sequence
faster than Cr50 and this isn't such a big problem for them.
However, even if they are faster they are still doing _some_
transfers over a SPI bus so this should benefit everyone even if to
a lesser extent.
* It's possible that there are extra delays in the code that could be
optimized out. I didn't dig since once I enabled async probe they
no longer impacted me.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued,
which will need the use of the internal command/response buffer. But,
we're issuing this *before* we've waited to make sure that buffer is
allocated.
This can result in intermittent failures to probe if the hypervisor / TPM
implementation doesn't respond quickly enough. I find it fails almost
every time with an 8 vcpu guest under KVM with software emulated TPM.
To fix it, just move the tpm2_get_cc_attrs_tlb() call after the
existing code to wait for initialization, which will ensure the buffer
is allocated.
Fixes: 18b3670d79 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Trivial fix, the spelling of "drescription" is incorrect
in function comment.
Fix this.
Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Found by smatch:
drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn:
variable dereferenced before check 'chip->ops' (see line 979)
'chip->ops' is assigned in the beginning of function
in tpmm_chip_alloc->tpm_chip_alloc
and is used before first possible goto to error path.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
During flow control we are just reading from the TPM, yet our spi_xfer
has the tx_buf and rx_buf both non-NULL which means we're requesting a
full duplex transfer.
SPI is always somewhat of a full duplex protocol anyway and in theory
the other side shouldn't really be looking at what we're sending it
during flow control, but it's still a bit ugly to be sending some
"random" data when we shouldn't.
The default tpm_tis_spi_flow_control() tries to address this by
setting 'phy->iobuf[0] = 0'. This partially avoids the problem of
sending "random" data, but since our tx_buf and rx_buf both point to
the same place I believe there is the potential of us sending the
TPM's previous byte back to it if we hit the retry loop.
Another flow control implementation, cr50_spi_flow_control(), doesn't
address this at all.
Let's clean this up and just make the tx_buf NULL before we call
flow_control(). Not only does this ensure that we're not sending any
"random" bytes but it also possibly could make the SPI controller
behave in a slightly more optimal way.
NOTE: no actual observed problems are fixed by this patch--it's was
just made based on code inspection.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
It has been reported that some TIS based TPMs are giving unexpected
errors when using the O_NONBLOCK path of the TPM device. The problem
is that some TPMs don't like it when you get and then relinquish a
locality (as the tpm_try_get_ops()/tpm_put_ops() pair does) without
sending a command. This currently happens all the time in the
O_NONBLOCK write path. Fix this by moving the tpm_try_get_ops()
further down the code to after the O_NONBLOCK determination is made.
This is safe because the priv->buffer_mutex still protects the priv
state being modified.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206275
Fixes: d23d124843 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Mario Limonciello <Mario.Limonciello@dell.com>
Tested-by: Alex Guzman <alex@guzman.io>
Cc: stable@vger.kernel.org
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
Also, the following issue shows up due to the flexible-array member
having incomplete type[4]:
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_bios_measurements_start’:
drivers/char/tpm/eventlog/tpm2.c:54:46: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
54 | size = sizeof(struct tcg_pcr_event) - sizeof(event_header->event)
| ^
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_bios_measurements_next’:
drivers/char/tpm/eventlog/tpm2.c:102:10: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
102 | sizeof(event_header->event) + event_header->event_size;
| ^
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_binary_bios_measurements_show’:
drivers/char/tpm/eventlog/tpm2.c:140:10: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
140 | sizeof(event_header->event) + event_header->event_size;
| ^
scripts/Makefile.build:266: recipe for target 'drivers/char/tpm/eventlog/tpm2.o' failed
make[3]: *** [drivers/char/tpm/eventlog/tpm2.o] Error 1
As mentioned above: "Flexible array members have incomplete type, and
so the sizeof operator may not be applied. As a quirk of the original
implementation of zero-length arrays, sizeof evaluates to zero."[1] As
in "sizeof(event_header->event) always evaluated to 0, so removing it
has no effect".
Lastly, make use of the struct_size() helper to deal with the
flexible array member and its host structure.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
[4] https://github.com/KSPP/linux/issues/43
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There is export_uuid() function which exports uuid_t to the u8 array.
Use it instead of open coding variant.
This allows to hide the uuid_t internals.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Call disable_interrupts() if we have to revert to polling in order not to
unnecessarily reserve the IRQ for the life-cycle of the driver.
Cc: stable@vger.kernel.org # 4.5.x
Reported-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e3837e74a0 ("tpm_tis: Refactor the interrupt setup")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
For the algorithm that does not match the bank, a positive
value EINVAL is returned here. I think this is a typo error.
It is necessary to return an error value.
Cc: stable@vger.kernel.org # 5.4.x
Fixes: 9f75c82246 ("KEYS: trusted: correctly initialize digests and fix locking issue")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_ibmvtpm_send() can fail during PowerVM Live Partition Mobility resume
with an H_CLOSED return from ibmvtpm_send_crq(). The PAPR says, 'The
"partner partition suspended" transport event disables the associated CRQ
such that any H_SEND_CRQ hcall() to the associated CRQ returns H_Closed
until the CRQ has been explicitly enabled using the H_ENABLE_CRQ hcall.'
This patch adds a check in tpm_ibmvtpm_send() for an H_CLOSED return from
ibmvtpm_send_crq() and in that case calls tpm_ibmvtpm_resume() and
retries the ibmvtpm_send_crq() once.
Cc: stable@vger.kernel.org # 3.7.x
Fixes: 132f762947 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Reported-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Tested-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch fixes the following problem when the ibmvtpm driver
is built as a module:
ERROR: modpost: "tpm2_get_cc_attrs_tbl" [drivers/char/tpm/tpm_ibmvtpm.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:94: __modpost] Error 1
make: *** [Makefile:1298: modules] Error 2
Fixes: 18b3670d79 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Commit 9255782f70 ("sysfs: Wrap __compat_only_sysfs_link_entry_to_kobj
function to change the symlink name") made this function a wrapper
around a new non-underscored function, which is a bit odd. The normal
naming convention is the other way around: the underscored function is
the wrappee, and the non-underscored function is the wrapper.
There's only one single user (well, two call-sites in that user) of the
more limited double underscore version of this function, so just remove
the oddly named wrapper entirely and just add the extra NULL argument to
the user.
I considered just doing that in the merge, but that tends to make
history really hard to read.
Link: https://lore.kernel.org/lkml/CAHk-=wgkkmNV5tMzQDmPAQuNJBuMcry--Jb+h8H1o4RA3kF7QQ@mail.gmail.com/
Cc: Sourabh Jain <sourabhjain@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support TPM2 in the IBM vTPM driver. The hypervisor tells us what
version of TPM is connected through the vio_device_id.
In case a TPM2 device is found, we set the TPM_CHIP_FLAG_TPM2 flag
and get the command codes attributes table. The driver does
not need the timeouts and durations, though.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.
This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.
Fixes: 132f762947 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
A vTPM 2.0 is identified by 'IBM,vtpm20' in the 'compatible' node in
the device tree. Handle it in the same way as 'IBM,vtpm'.
The vTPM 2.0's log is written in little endian format so that for this
aspect we can rely on existing code.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In a recent change to the SPI subsystem [1], a new 'delay' struct was added
to replace the 'delay_usecs'. This change replaces the current
'delay_usecs' with 'delay' for this driver.
The 'spi_transfer_delay_exec()' function [in the SPI framework] makes sure
that both 'delay_usecs' & 'delay' are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
For /sys/kernel/security/tpm0/binary_bios_measurements:
1) read after lseek beyound end of file generates whole last line.
2) read after lseek to middle of last line generates
expected end of last line and unexpected whole last line once again.
Cc: stable@vger.kernel.org # 4.19.x
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
In case of /sys/kernel/security/tpm0/ascii_bios_measurements
and binary_bios_measurements:
1) read after lseek beyound end of file generates whole last line.
2) read after lseek to middle of last line generates
expected end of last line and unexpected whole last line once again.
Cc: stable@vger.kernel.org # 4.19.x
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If a TPM is in disabled state, it's reasonable for it to have an empty
log. Bailing out of probe in this case means that the PPI interface
isn't available, so there's no way to then enable the TPM from the OS.
In general it seems reasonable to ignore log errors - they shouldn't
interfere with any other TPM functionality.
Signed-off-by: Matthew Garrett <matthewgarrett@google.com>
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
chip->allocated_banks, an array of tpm_bank_info structures, contains the
list of TPM algorithm IDs of allocated PCR banks. It also contains the
corresponding ID of the crypto subsystem, so that users of the TPM driver
can calculate a digest for a PCR extend operation.
However, if there is no mapping between TPM algorithm ID and crypto ID, the
crypto_id field of tpm_bank_info remains set to zero (the array is
allocated and initialized with kcalloc() in tpm2_get_pcr_allocation()).
Zero should not be used as value for unknown mappings, as it is a valid
crypto ID (HASH_ALGO_MD4).
Thus, initialize crypto_id to HASH_ALGO__LAST.
Cc: stable@vger.kernel.org # 5.1.x
Fixes: 879b589210 ("tpm: retrieve digest size of unknown algorithms with PCR read")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Revert tpm_tis_spi_mod.ko back to tpm_tis_spi.ko as the rename could
break user space scripts. This can be achieved by renaming tpm_tis_spi.c
as tpm_tis_spi_main.c. Then tpm_tis_spi-y can be used inside the
makefile.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org # 5.5.x
Fixes: 797c0113c9 ("tpm: tpm_tis_spi: Support cr50 devices")
Reported-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Easily determining what TCG version a tpm device implements
has been a pain point for userspace for a long time, so
add a sysfs file to report the TCG major version of a tpm device.
Also add an entry to Documentation/ABI/stable/sysfs-class-tpm
describing the new file.
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-integrity@vger.kernel.org
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The priv->response_length can hold the size of an response or an negative
error code, and the tpm_common_read() needs to handle both cases correctly.
Changed the type of response_length to signed and accounted for negative
value in tpm_common_read().
Cc: stable@vger.kernel.org
Fixes: d23d124843 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There has been a bunch of reports (one from kernel bugzilla linked)
reporting that when this commit is applied it causes on some machines
boot freezes.
Unfortunately hardware where this commit causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's fix was supposed to fix.
Fixes: 21df4a8b60 ("tpm_tis: reserve chip for duration of tpm_tis_core_init")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There has been a bunch of reports (one from kernel bugzilla linked)
reporting that when this commit is applied it causes on some machines
boot freezes.
Unfortunately hardware where this commit causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's fix was supposed to fix.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Fixes: 1ea32c83c6 ("tpm_tis_core: Set TPM_CHIP_FLAG_IRQ before probing for interrupts")
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Revert a commit, which was included in Linux v5.5-rc3 because it did not
properly fix the issues it was supposed to fix.
Fixes: 21df4a8b60 ("tpm_tis: reserve chip for duration of tpm_tis_core_init")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
