Correct the power limit setting for SMU V11 asics.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable power source switch on Sienna Cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct pipe offset calculation in is_pipe_enabled function,
it should be done in queues.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After refactor our amdgpu_dm_atomic_commit, this function only invoke
drm_atomic_helper_commit. For this reason, this commit drops
amdgpu_dm_atomic_commit and add drm_atomic_helper_commit directly in the
atomic_commit hook.
v2: squash in warning fix (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The text output should not be more than a page, so only print the first
32 page table entries.
If we need all of them we can still look into the binary trace.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Macronix MX35LF1G24AD(/2G24AD/4G24AD) are 3V, 1G/2G/4Gbit serial
SLC NAND flash device (without on-die ECC).
Validated by read, erase, read back, write, read back on Xilinx Zynq
PicoZed FPGA board which included Macronix SPI Host(drivers/spi/spi-mxic.c)
& S/W BCH ecc(drivers/mtd/nand/ecc-sw-bch.c) with bug fixing patch
(mtd: nand: ecc-bch: Fix the size of calc_buf/code_buf of the BCH).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1607570529-22341-3-git-send-email-ycllin@mxic.com.tw
This driver supports Rockchip NFC (NAND Flash Controller) found on RK3308,
RK2928, RKPX30, RV1108 and other SOCs. The driver has been tested using
8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to use
the BBT(bad block table).
Suggested-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201210002134.5686-3-yifeng.zhao@rock-chips.com
Set the GPMI CTRL1 GANGED_RDYBUSY bit so driver can sense the R/B signal
from all CS.
For the NAND chip MT29F64G08AFAAAWP, only the first chip detected
without the patch.
[ 3.764118] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770613] nand: Micron MT29F64G08AFAAAWP
[ 3.774752] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.786421] Bad block table found at page 524160, version 0x01
[ 3.792730] Bad block table found at page 524032, version 0x01
After applying the patch
[ 3.764445] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770941] nand: Micron MT29F64G08AFAAAWP
[ 3.775080] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.784390] nand: 2 chips detected
[ 3.790900] Bad block table found at page 524160, version 0x01
[ 3.796776] Bad block table found at page 1048448, version 0x01
Signed-off-by: Han Xu <han.xu@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-2-han.xu@nxp.com
SDX55 uses QPIC version 2.0.0 IP for the NAND controller support.
In this version, DEV_CMD_* registers are moved to operational state,
hence CPU access in BAM mode is restricted. So, skip accessing these
registers and also use a different config for reading ONFI parameters.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126085705.48399-3-manivannan.sadhasivam@linaro.org
Call clk_disable_unprepare(nfc->phase_rx) if the clk_set_rate() function
fails to avoid a resource leak.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/X8ikVCnUsfTpffFB@mwanda
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126030946.2058-1-festevam@gmail.com
This patch adds the new IP of Nand Flash Controller(NFC) support
on Intel's Lightning Mountain(LGM) SoC.
DMA is used for burst data transfer operation, also DMA HW supports
aligned 32bit memory address and aligned data access by default.
DMA burst of 8 supported. Data register used to support the read/write
operation from/to device.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110012333.18647-3-vadivel.muruganx.ramuthevar@linux.intel.com
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, it will result in reference leak in
the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover,
this device cannot enter the idle state and always stay busy or
other non-idle state later. So we fixed it through adding
pm_runtime_put_noidle.
Fixes: 5bc6bb603b ("mtd: rawnand: gpmi: Fix suspend/resume problem")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
Driver requires different amount of clocks for different SoCs. Describe
these requirements properly to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dt.yaml: nand-controller@33002000: clock-names:1: 'gpmi_apb' was expected
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201029162021.80839-1-krzk@kernel.org
If an error happens in mtd_device_parse_register or mtd_device_register,
memory allocated for struct platram_info is leaked.
Make platram_probe() call platram_remove() on all error paths
after struct platram_info allocation to correctly free resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Baskov Evgeiny <baskov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113160537.899-1-baskov@ispras.ru
struct mtd_info has a flag oops_panic_write which is set when the write
operation is issued via the panic_write() callback. That allows controller
drivers to distinguish the panic write from a regular write.
Replace the open coded 'in_interrupt() | oops_in_progress' checks with a
check for that flag. in_interrupt() is an unrealiable indicator anyway as
it covers all sorts of atomic contexts not only hard and soft interrupt
service routines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-mtd@lists.infradead.org
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113141422.2214771-1-bigeasy@linutronix.de
While working a bit on this driver I dropped the platform includes and
commented a few lines just to verify the correctness of my changes. It
appeared the following:
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_waitrdy’:
drivers/mtd/nand/raw/au1550nd.c:130:3: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
usleep_range(10, 100);
^~~~~~~~~~~~
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_exec_instr’:
drivers/mtd/nand/raw/au1550nd.c:188:3: error: implicit declaration of function ‘ndelay’ [-Werror=implicit-function-declaration]
ndelay(instr->delay_ns);
^~~~~~
I think the delay.h header should be included in this file and not
come from one of its platform includes, so let's add it here.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113124021.32675-1-miquel.raynal@bootlin.com
The NAND ECC core is included in the generic NAND core when it is
compiled in.
Different software ECC engines drivers will select the NAND ECC core
and thus also have a dependency on the NAND core. Using a "depends on"
between the two leads to possible cases (not real cases, but created
by robots) where one is still unselected because of the "select does
not verifies depends on" game:
WARNING: unmet direct dependencies detected for MTD_NAND_ECC
Depends on [n]: MTD [=m] && MTD_NAND_CORE [=n]
Selected by [m]:
- MTD_NAND_ECC_SW_HAMMING [=y] && MTD [=m]
- MTD_NAND_ECC_SW_BCH [=y] && MTD [=m]
Fix this by using a select instead.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/linux-mtd/20201113123945.32592-1-miquel.raynal@bootlin.com
Moving files around produced the following warnings:
Error: Cannot open file drivers/mtd/nand/raw/nand_ecc.c
Error: Cannot open file drivers/mtd/nand/raw/nand_ecc.c
Fix one by just dropping the reference because it is not relevant, the
other by using a better noun instead of a file name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123831.32429-1-miquel.raynal@bootlin.com
i.MX is a devicetree-only platform now and the existing platform data
support in this driver was only useful for old non-devicetree platforms.
Get rid of the platform data support since it is no longer used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110121908.19400-1-festevam@gmail.com
of_find_device_by_node() already takes a reference to the device, and
ingenic_ecc_release() will drop the reference. So, the get_device() in
ingenic_ecc_get() is redundand.
Fixes: 15de8c6efd0e("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201031105439.2304211-1-yukuai3@huawei.com
This code has been written in 2008 and is fine, but in order to keep
robots happy, I think it's time to change a little bit this code just
to clarify the different possible values of eccsize_mult. Indeed, this
variable may only take the value 1 or 2 because step_size, in the case
of the software Hamming ECC engine may only be 256 or 512. Depending
on the value of eccsize_mult, an extra rp17 variable is set, or not
and triggers the following warning:
smatch warnings:
ecc_sw_hamming_calculate() error: uninitialized symbol 'rp17'.
As highlighted by Dan Carpenter, if the only possible values for
eccsize_mult are 1 and 2, then the code is fine, but "it's hard to
tell just from looking".
So instead of shifting step_size, let's use a ternary condition to
assign to eccsize_mult the only two possible values and clarify the
driver's logic.
Now that the situation is clarified for humans, ensure rp17 is
initialized to 0 to keep compilers and robots silent as well.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201030172333.28390-1-miquel.raynal@bootlin.com
This patch enables NAND MDMA (MBUS DMA) mode for
the Allwinner SoCs A23/A33/H3.
The DMA transfer method gets sets now to MBUS DMA as default for
the sun8i-a23-nand-controller (till now DMA transfer was executed
via the shared DMA engine).
The main advantage is more bandwidth for the users of the shared DMA
engine and also that the MBUS DMA setup requires less configuration
effort. For example you don't need to define a dedicated DMA channel
in the device-tree any more.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Manuel Dipolt <manuel.dipolt@robart.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/154840787.280672.1602517282173.JavaMail.zimbra@robart.cc
After each codeword NAND_FLASH_STATUS is read for possible operational
failures. But there is no DMA sync for CPU operation before reading it
and this leads to incorrect or older copy of DMA buffer in reg_read_buf.
This patch adds the DMA sync on reg_read_buf for CPU before reading it.
Fixes: 5bc36b2bf6 ("mtd: rawnand: qcom: check for operation errors in case of raw read")
Cc: stable@vger.kernel.org
Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1602230872-25616-1-git-send-email-ipkumar@codeaurora.org
Even if this is not supposed to happen, there is no reason to fail the
probe if it was explicitly requested to use no ECC engine at all (for
instance, during development). This condition is met by just
commenting out the error on the OOB free bytes count after the
assignation of an ECC engine if none was provided (any other situation
would error out much earlier anyway).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-5-miquel.raynal@bootlin.com
Now that all the logic is available in the NAND core, let's use it
from the SPI-NAND core. Right now there is no functional change as the
default ECC engine for SPI-NANDs is set to 'on-die', but user can now
use software correction if they want to by just setting the right
properties in the DT.
Also note that the OOB layout handling is removed from the SPI-NAND
core as each ECC engine is supposed to handle it by it's own; users
should not be aware of that.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-4-miquel.raynal@bootlin.com
This property does not describe very well its purpose: it describes
the ECC engine type. Deprecate it in favor of nand-ecc-engine which
points to either the NAND part itself in case of on-die ECC, or to the
parent node in case of an integrated ECC engine in the NAND controller
(previously referred as "hardware") or to another node in case of an
external controller. Other "modes" (none/software) are achieved with
the new nand-use-soft-ecc-engine and nand-no-ecc-engine properties.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-3-miquel.raynal@bootlin.com
Add the logic in the NAND core to find the right ECC engine depending
on the NAND chip requirements and the user desires. Right now, the
choice may be made between (more will come):
* software Hamming
* software BCH
* on-die (SPI-NAND devices only)
Once the ECC engine has been found, the ECC engine must be
configured.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-2-miquel.raynal@bootlin.com
The SPI-NAND layer default is on-die ECC because until now it was the
only one supported. New SPI-NAND chip flavors might use something else
as ECC engine provider but this will always be the default if the user
does not choose explicitly something else.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-6-miquel.raynal@bootlin.com
Make use of the existing functions taken from the SPI-NAND core to
instantiate an on-die ECC engine specific to the SPI-NAND core. The
next step will be to tweak the core to use this object instead of
calling the helpers directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-4-miquel.raynal@bootlin.com
