The commit 92adc96f8e ("ALSA: usb-audio: set the interface format
after resume on Dell WD19") introduced the workaround for the broken
setup after the resume specifically on a Dell dock model. However,
the full setup should have been performed after the resume on all
devices, as we can't guarantee the same state. So this patch removes
the conditional check and applies the workaround always.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare_data_urb and retire_data_urb fields of the endpoint object
are set dynamically at PCM trigger start/stop. Those are evaluated in
the endpoint handler, but there can be a race, especially if two
different PCM substreams are handling the same endpoint for the
implicit feedback case. Also, the data_subs field of the endpoint is
set and accessed dynamically, too, which has the same risk.
As a slight improvement for the concurrency, this patch introduces the
function to set the callbacks and the data in a shot with the memory
barrier. In the reader side, it's also fetched with the memory
barrier.
There is still a room of race if prepare and retire callbacks are set
during executing the URB completion. But such an inconsistency may
happen only for the implicit fb source, i.e. it's only about the
capture stream. And luckily, the capture stream never sets the
prepare callback, hence the problem doesn't happen practically.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
start_endpoints() may leave the data endpoint running if an error
happens at starting the sync endpoint. We should stop both streams
properly, instead.
While we're at it, move the debug prints into the endpoint.c that is a
more suitable place.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary patch for the later big change. Just a minor code
refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the active altsetting at changing sample rate seems
unrecommended. The host should deselect the altsetting at first
before that, then select it again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-18-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper function to retrieve the usb_host_interface object from
the given interface and altsetting number pair, which is a commonly
used procedure in the driver code.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-17-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This behavior turned out to be invalid from the USB spec POV and
shouldn't be applied. As it's an optional flag that is set only via
an card control element that must be hardly used, let's drop it
again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-16-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd_usb_endpoint objects are created at first when the
substream is opened and tries to assign the endpoints corresponding to
the matching audioformat. But since basically the all endpoints have
been already parsed and the information have been obtained, we may
create the endpoint objects statically at the init phase. It's easier
to manage for the implicit fb case, for example.
This patch changes the endpoint object management and lets the parser
to create the all endpoint objects.
This change shouldn't bring any functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-15-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The implicit feedback mode initializes both the main data stream and
the sync data stream. When a sync stream was already opened, this
would result in the doubly initialization and might screw up things.
Add the check of already opened sync streams and skip the unnecessary
initialization.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file debug.h contains a simple macro for debug prints, and it's
used only in two places, the format parser and the hw_params rules.
The former actually should print a more informative message instead,
so the only users are the hw_parmas rules.
This patch moves the contents of debug.h into the hw_params rules
local code and remove the unneeded includes. Also, the debug print in
the format parser is replaced with the information print with more
useful information, and the raw printk() call is replaced with
pr_debug().
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several hw_params functions narrows the interval via min/max rule in
the very similar way, so factor out those into a helper function and
use commonly.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, there is no check at the stream open time whether
the endpoint is being already used by others. In the normal
operations, this shouldn't happen, but in the case of the implicit
feedback mode, it's a common problem with the full duplex operation,
because the capture stream is always opened by the playback stream as
an implicit sync source.
Although we recently introduced the check of such a conflict of
parameters at the PCM hw_params time, it doesn't give any hint at the
hw_params itself and just gives the error. This isn't quite
comfortable, and it caused problems on many applications.
This patch attempts to make the parameter handling easier by
introducing the strict hw constraint matching with the counterpart
stream that is being used. That said, when an implicit feedback
playback stream is running before a capture stream is opened, the
capture stream carries the PCM hw-constraint to allow only the same
sample rate, format, periods and period frames as the running playback
stream. If not opened or there is no conflict of endpoints, the
behavior remains as same as before.
Note that this kind of "weak link" should work for most cases, but
this is no concrete solution; e.g. if an application changes the hw
params multiple times while another stream is opened, this would lead
to inconsistencies.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary work for the upcoming hw-constraint change for
the implicit feedback mode.
Currently snd_usb_autoresume() is called at the end of
setup_hwinfo(). It's a bit confusing; because of this implicit
refcount usage, the caller side needs to call snd_usb_autosuspend()
later in the error path although it's not seen inside the function.
Instead, it's clearer to call both snd_usb_autoresume() and suspend()
in the very same function.
It's only refactoring and no functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of parsing and evaluating the sync endpoint and the implicit
feedback mode at each time the audio stream is opened, let's parse it
once at the probe time, as the all needed information can be obtained
statically from the descriptor or from the quirk.
This patch extends audioformat struct to record the sync endpoint,
interface and altsetting as well as the implicit feedback flag, which
are filled at parsing the streams. Then, set_sync_endpoint() is much
simplified just to follow the already parsed data.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few rooms for improvements wrt the debug prints:
- The EP debug print is shown only at starting, not at stopping
- The EP debug print contains useless object addresses
- Some helpers show the urb and the EP object addresses, too
This patch addresses those shortcomings.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sync EP setup isn't cleared at stopping the stream but expected to
be cleared at the next stream start. This may leave the sync link
setup stale and can spoof wrongly when full duplex streams were
running in the implicit fb sync. Let's initialize them properly at
start and end of the stream.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Factor out the code to obtain snd_usb_endpoint object matching with
the given endpoint. It'll be used in the later patch to add the
implicit feedback hw-constraint.
No functional change by this patch itself.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that many UAC2 devices are with the implicit feedback, but
they couldn't be probed properly because the assumption the driver
takes currently isn't applied: they have the single endpoint for both
data and implicit-fb streams, while we checked only the classical sync
endpoints assigned to the next altsetting in the same interface.
This patch extends the search to match with those typical cases where
the implicit fb stream is found in the next interface number.
While we're at it, slightly refactor the code, not returning 0/-ERROR
but use the standard bool to success/failur, which is more intuitive
in this particular case.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current driver code assumes blindly that all found sample rates for
the same endpoint from the UAC2 and UAC3 descriptors can be used no
matter which altsetting, but actually this was wrong: some devices
accept only limited sample rates in each altsetting. For determining
which altsetting supports which rate, we need to verify each sample rate
and check the validity via UAC2_AS_VAL_ALT_SETTINGS. This control
reports back the available altsettings as a bitmap.
This patch implements the missing piece above, the verification and
reconstructs the sample rate tables based on the result.
An open question is how to deal with the altsettings that ended up
with no valid sample rates after verification. At least, there is a
device that showed this problem although the sample rates did work in
the later usage (see bug link). For now, we accept such an altset as
is, assuming that it's a firmware bug.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1178203
Link: https://lore.kernel.org/r/20201123085347.19667-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM trigger callback is atomic, hence we must not call a function
like usb_set_interface() there. Calling it from there would lead to a
kernel Oops.
Fix it by moving the usb_set_interface() call to set_sync_endpoint().
Also, apply the snd_usb_set_interface_quirk() for consistency, too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, when the device provides the discrete sample rate
tables with unusual sample rates, the driver tries to gather the whole
values from the audioformat entries and create a hw-constraint rule to
restrict with this single rate list. This is rather inefficient and
may overlook the rates that are associated only with the certain
audioformat entries.
This patch improves the hw constraint setup by rewriting the existing
hw_rule_rate(). The discrete sample rates (identified by rate_table
and nr_rates of format entry) are checked in the existing
hw_rule_rate() instead of extra rules; in the case of discrete rates,
the function compares with each rate table entry and calculates the
min/max values from there. For the contiguous rates, the behavior
doesn't change.
Along with it, snd_usb_pcm_check_knot() and snb_usb_substream
rate_list field become superfluous, thus those are dropped.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Given the case that bootloader(such as UEFI)'s FSPI driver might not
handle all interrupts before loading kernel, those legacy interrupts
would assert immidiately once kernel's FSPI driver enable them. Further,
if it was FSPI_INTR_IPCMDDONE, the irq handler nxp_fspi_irq_handler()
would call complete(&f->c) to notify others. However, f->c might not be
initialized yet at that time, then cause kernel panic.
Of cause, we should fix this issue within bootloader. But it would be
better to have this pacth to make dirver more robust (by clearing all
interrupt status bits before enabling interrupts).
Suggested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201123025715.14635-1-ran.wang_1@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For inline web links, no special markup is needed.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If some errors are detected at the same time as the access end
interrupt, the access end interrupt was not cleared. Especially with
DMA, because then the access end interrupt was never enabled and, thus,
never cleared. Clear the interrupt register always when a command error
occurs.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rebase to v5.4]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebase and extension of the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201117131337.35307-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20201117113750.25053-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD IOMMU requires 4k-aligned pages for the event log, the PPR log,
and the completion wait write-back regions. However, when allocating
the pages, they could be part of large mapping (e.g. 2M) page.
This causes #PF due to the SNP RMP hardware enforces the check based
on the page level for these data structures.
So, fix by calling set_memory_4k() on the allocated pages.
Fixes: c69d89aff3 ("iommu/amd: Use 4K page for completion wait write-back semaphore")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Link: https://lore.kernel.org/r/20201105145832.3065-1-suravee.suthikulpanit@amd.com
Signed-off-by: Will Deacon <will@kernel.org>
advance_transaction() is using in_interrupt() to distinguish between
an invocation from the interrupt handler and an invocation from
another part of the stack.
This looks misleading because chains like
acpi_update_all_gpes() -> acpi_ev_gpe_detect() ->
acpi_ev_detect_gpe() -> acpi_ec_gpe_handler()
should probably also behave as if they were called from an interrupt
handler.
Replace in_interrupt() usage with a function parameter.
Set this parameter to `true' if invoked from an interrupt handler
(acpi_ec_gpe_handler() and acpi_ec_irq_handler()) and `false'
otherwise.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit d0511b5496.
After some time it was noticed that the Tegra186 among others
were experiencing problems when making this into a module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix incorrect netdev reference count in xsk_bind operation. Incorrect
reference count of the device appears when a user calls bind with the
XDP_ZEROCOPY flag on an interface which does not support zero-copy.
In such a case, an error is returned but the reference count is not
decreased. This change fixes the fault, by decreasing the reference count
in case of such an error.
The problem being corrected appeared in '162c820ed896' for the first time,
and the code was moved to new file location over the time with commit
'c2d3d6a47462'. This specific patch applies to all version starting
from 'c2d3d6a47462'. The same solution should be applied but on different
file (net/xdp/xdp_umem.c) and function (xdp_umem_assign_dev) for versions
from '162c820ed896' to 'c2d3d6a47462' excluded.
Fixes: 162c820ed8 ("xdp: hold device for umem regardless of zero-copy mode")
Signed-off-by: Marek Majtyka <marekx.majtyka@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20201120151443.105903-1-marekx.majtyka@intel.com
Pull SCMI cpufreq driver fix for 5.10-rc6 from Viresh Kumar:
"This fixes a build issues with SCMI cpufreq driver in the
!CONFIG_COMMON_CLK case."
* 'cpufreq/arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Fix build for !CONFIG_COMMON_CLK
Add OBDA0623 ACPI HID to the acpi_device_id table. This HID is used
for the RTL8723BS Bluetooth part on the Acer Switch 10E SW3-016.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1665610
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f4 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix following warnings caused by mismatch between
function parameters and function comments.
drivers/acpi/arm64/iort.c:55: warning: Function parameter or member 'iort_node' not described in 'iort_set_fwnode'
drivers/acpi/arm64/iort.c:55: warning: Excess function parameter 'node' description in 'iort_set_fwnode'
drivers/acpi/arm64/iort.c:682: warning: Function parameter or member 'id' not described in 'iort_get_device_domain'
drivers/acpi/arm64/iort.c:682: warning: Function parameter or member 'bus_token' not described in 'iort_get_device_domain'
drivers/acpi/arm64/iort.c:682: warning: Excess function parameter 'req_id' description in 'iort_get_device_domain'
drivers/acpi/arm64/iort.c:1142: warning: Function parameter or member 'dma_size' not described in 'iort_dma_setup'
drivers/acpi/arm64/iort.c:1142: warning: Excess function parameter 'size' description in 'iort_dma_setup'
drivers/acpi/arm64/iort.c:1534: warning: Function parameter or member 'ops' not described in 'iort_add_platform_device'
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20201014093139.1580-1-shiju.jose@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Implement the previously removed getcpu vdso syscall by using the
TOD programmable field to pass the cpu number to user space.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Verify on exit to user space that always
- the primary ASCE (cr1) is set to kernel ASCE
- the secondary ASCE (cr7) is set to user ASCE
If this is not the case: panic since something went terribly wrong.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Create a region 3 page table which contains only invalid entries, and
use that via "s390_invalid_asce" instead of the kernel ASCE whenever
there is either
- no user address space available, e.g. during early startup
- as an intermediate ASCE when address spaces are switched
This makes sure that user space accesses in such situations are
guaranteed to fail.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove set_fs support from s390. With doing this rework address space
handling and simplify it. As a result address spaces are now setup
like this:
CPU running in | %cr1 ASCE | %cr7 ASCE | %cr13 ASCE
----------------------------|-----------|-----------|-----------
user space | user | user | kernel
kernel, normal execution | kernel | user | kernel
kernel, kvm guest execution | gmap | user | kernel
To achieve this the getcpu vdso syscall is removed in order to avoid
secondary address mode and a separate vdso address space in for user
space. The getcpu vdso syscall will be implemented differently with a
subsequent patch.
The kernel accesses user space always via secondary address space.
This happens in different ways:
- with mvcos in home space mode and directly read/write to secondary
address space
- with mvcs/mvcp in primary space mode and copy from primary space to
secondary space or vice versa
- with e.g. cs in secondary space mode and access secondary space
Switching translation modes happens with sacf before and after
instructions which access user space, like before.
Lazy handling of control register reloading is removed in the hope to
make everything simpler, but at the cost of making kernel entry and
exit a bit slower. That is: on kernel entry the primary asce is always
changed to contain the kernel asce, and on kernel exit the primary
asce is changed again so it contains the user asce.
In kernel mode there is only one exception to the primary asce: when
kvm guests are executed the primary asce contains the gmap asce (which
describes the guest address space). The primary asce is reset to
kernel asce whenever kvm guest execution is interrupted, so that this
doesn't has to be taken into account for any user space accesses.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Adding <asm/exception.h> brought in <asm/kprobes.h> which uses
<asm/probes.h>, which uses 'pstate_check_t' so the latter needs to
#include <asm/insn.h> for this typedef.
Fixes this build error:
In file included from arch/arm64/include/asm/kprobes.h:24,
from arch/arm64/include/asm/exception.h:11,
from arch/arm64/kernel/fpsimd.c:35:
arch/arm64/include/asm/probes.h:16:2: error: unknown type name 'pstate_check_t'
16 | pstate_check_t *pstate_cc;
Fixes: c6b90d5cf6 ("arm64/fpsimd: Fix missing-prototypes in fpsimd.c")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/20201123044510.9942-1-rdunlap@infradead.org
Signed-off-by: Will Deacon <will@kernel.org>
We need to disable interrupts in load_fpu_regs(). Otherwise an
interrupt might come in after the registers are loaded, but before
CIF_FPU is cleared in load_fpu_regs(). When the interrupt returns,
CIF_FPU will be cleared and the registers will never be restored.
The entry.S code usually saves the interrupt state in __SF_EMPTY on the
stack when disabling/restoring interrupts. sie64a however saves the pointer
to the sie control block in __SF_SIE_CONTROL, which references the same
location. This is non-obvious to the reader. To avoid thrashing the sie
control block pointer in load_fpu_regs(), move the __SIE_* offsets eight
bytes after __SF_EMPTY on the stack.
Cc: <stable@vger.kernel.org> # 5.8
Fixes: 0b0ed657fe ("s390: remove critical section cleanup from entry.S")
Reported-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Merge swiotlb updates from Konrad, as we depend on the updated function
prototype for swiotlb_tbl_map_single(), which dropped the 'tbl_dma_addr'
argument in -rc4.
* 'stable/for-linus-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: remove the tbl_dma_addr argument to swiotlb_tbl_map_single
swiotlb: fix "x86: Don't panic if can not alloc buffer for swiotlb"
Commit c604abc3f6 ("vmlinux.lds.h: Split ELF_DETAILS from STABS_DEBUG")
after should add a missing ELF_DETAILS, at the same time, the .comment
section has been included in the ELF_DETAILS.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Link: https://lore.kernel.org/r/1605852494-23515-1-git-send-email-tangyouling@loongson.cn
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is still some missing hardware support that affects all models,
such as sound chip and localtalk support. However, many models are well
supported, including the Quadra 800 emulated by QEMU. Missing hardware
support is mostly documented at the web site, so add the URL.
Cc: Joshua Thompson <funaho@jurai.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Link: https://lore.kernel.org/r/bb327f05f8fb61eeb332cc2ba4e8335570976474.1605847196.git.fthain@telegraphics.com.au
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
