This depends on the patch "genirq: irqchip: Add mask to block out invalid irqs"
and masks out reserved bits using the unused interrupt bitfield.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This depends on the patch "genirq: Generic chip: Add linear irq domain support"
and removes the custom IPU irq_chip and irq_domain_ops. Instead, the generic
irq chip implementation is reused.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 8cf1e98114
("drm: Add consistency check for page-flipping") drm_mode_page_flip_ioctl
contains a WARN_ON that triggers if the .page_flip callback didn't update
the crtc->fb pointer to the new framebuffer immediately.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPU can request up to four pixels per access, which gives four
times the bandwidth compared to what the driver currently assumes.
After correcting this, we have to increase safety margins for
bandwidth requirement calculations.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPU has a lot of interrupts. Instead of allocating descs for all
of them, register a linear irq domain and create mappings as needed.
This was listed in the TODO as a prerequisite to move the IPU driver
out of staging.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 15 32-bit registers altogether.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 18 bit is supported as datawidth in device tree it should be
supported in driver. Beside the LDB channel the IPU channel has also
to be configured to use BGR666.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for the LVDS Display Bridge contained
in i.MX5 and i.MX6 SoCs.
Bit mapping, data width, and video timings are configurable
via device tree. Dual-channel mode is supported for a single
high-resolution source.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a MODULE_DEVICE_TABLE annotation so that parallel display module
can be autoloaded based on the device-tree information.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
partial fix of changes from
"staging: drm/imx: Add support for VGA via TVE on i.MX53"
parallel display support / DVI needs the original setting to work
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Rogerio Pimentel <rpimentel.silva@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
partial fix of changes from
"staging: drm/imx: Add support for VGA via TVE on i.MX53"
Have to check for vsync_pin instead of hsync_pin to set Vsync_pol.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Rogerio Pimentel <rpimentel.silva@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
partial fix of changes from
"staging: drm/imx: Add support for VGA via TVE on i.MX53"
Have to call imx_drm_crtc_panel_format_pins in imx_drm_crtc_panel_format
with the correct pins instead of (0, 0) This enables configuration of
correct waveforms for vsync / hsync for parallel display, LDB (i.MX53 and
i.MX6) as well as HDMI and MIPI (i.MX6)
TODO: configure pins via device tree
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the changes here, and we resolve the merge conflict that was
happening in the nvec_kbd.c file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also, slightly changes the behavior to always put the vblank irq,
even if userspace did not request a vblank event. As far as I
can tell, the previous code would leak a vblank irq refcnt if
userspace requested a pageflip without event.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since commit c8801a8 (regulator: core: Mark all get and enable calls as
__must_check) we need to check the value returned by 'regulator_enable()'.
Do this check to get rid of the following build warning:
drivers/staging/imx-drm/imx-tve.c: In function 'imx_tve_probe':
drivers/staging/imx-drm/imx-tve.c:671:19: warning: ignoring return value of 'regulator_enable', declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, I get the following problem when building kernel:
drivers/built-in.o: In function `imx_pd_connector_get_modes':
/linux-2.6/drivers/staging/imx-drm/parallel-display.c:78: undefined reference to `of_get_drm_display_mode'
make: *** [vmlinux] Error 1
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a call to deprecated devm_request_and_ioremap by devm_ioremap_resource.
Found with coccicheck and this semantic patch:
scripts/coccinelle/api/devm_request_and_ioremap.cocci.
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx DRM driver needs a couple of extra Kconfig dependencies
to avoid random build failures:
drivers/staging/imx-drm/ipuv3-crtc.c:448:
undefined reference to `ipu_idmac_put'
drivers/staging/imx-drm/ipuv3-crtc.c:450: undefined reference to
`ipu_dmfc_put' drivers/staging/imx-drm/ipuv3-crtc.c:452:
undefined reference to `ipu_dp_put'
drivers/staging/imx-drm/ipuv3-crtc.c:454: undefined reference to
`ipu_di_put'
drivers/built-in.o: In function `ipu_probe':
:(.text+0x4b4174): undefined reference to `device_reset'
drivers/built-in.o: In function `imx_tve_probe':
drivers/staging/imx-drm/imx-tve.c:648: undefined reference to
`devm_regmap_init_mmio_clk'
drivers/built-in.o: In function
`imx_pd_connector_get_modes':
drivers/staging/imx-drm/parallel-display.c:78: undefined
reference to `of_get_drm_display_mode'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
Support the BGR666 format on the IPUv3 parallel display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Enable anatop, well bisa and RBC for suspend to optimize the power
consumption a little bit
* Clock changes for TVE, LDB, PATA, SRTC support
* Add System Reset Controller (SRC) support for imx5 and imx6
* Add initial imx6dl support based on imx6q code
* Kconfig for cpufreq-cpu0, defconfig updates and few other changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRZ/viAAoJEFBXWFqHsHzOyqUH/2t7CCwlfTVUJYDCeo6PaE9x
41cV5zG6RvX1OfkRUmJ2N2klGn4zhwg6GHsCDQmvs+IODs4E7JeB9M92FAaPng71
NnuuwCQ01iIoaTtkz8z/n3tSet3fYB+xfNCMJoWIyS0edFFkCjOgnqRsA0pHRIOp
G6ey1kU80D0f4+DjAUg1mkIvJrZxbRKDwmwqfDGJzQ4VU7cv70n027YuMKbeMyCC
zdeKmpKSEl9AY+O/zeMrf03zEW+kdZ4eB6cTUFlpzYwPYY9o+XHx0U0535F7/x4+
KObUZ9Qg7liP5WO3ZzkVff5HJqPs6s/q99eOsU4/okF1x0fpq2mSgIHlSw4HpK8=
=TuTx
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc2
From Shawn Guo:
The imx soc changes for 3.10:
* Enable anatop, well bisa and RBC for suspend to optimize the power
consumption a little bit
* Clock changes for TVE, LDB, PATA, SRTC support
* Add System Reset Controller (SRC) support for imx5 and imx6
* Add initial imx6dl support based on imx6q code
* Kconfig for cpufreq-cpu0, defconfig updates and few other changes
* tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6: (275 commits)
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
ARM: i.MX53 Add the cko1, cko2 clock outputs.
staging: drm/imx: Use SRC to reset IPU
ARM i.MX6q: Add GPU, VPU, IPU, and OpenVG resets to System Reset Controller (SRC)
ARM: imx: do not use regmap_read for ANADIG_DIGPROG
ARM i.MX6q: set the LDB serial clock parent to the video PLL
ARM i.MX6q: Add audio/video PLL post dividers for i.MX6q rev 1.1
ARM i.MX6q: fix ldb di divider and selector clocks
ARM i.MX53: fix ldb di divider and selector clocks
ARM i.MX: Add imx_clk_divider_flags and imx_clk_mux_flags
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Trivial change/change conflict in arch/arm/mach-imx/mach-imx6q.c resolved.
Request the System Reset Controller to reset the IPU if
specified via device tree phandle.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
One of the main things to do to the driver is to support
the common display famework (CDF) to hit mainline. As this will
make some changes to the devicetree bindings necessary it makes
sense to do it before we move out of staging.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver adds support for the Television Encoder integrated
on i.MX53 SoCs (TVEv2).
Currently only the VGA output mode is supported, which only uses
the TVDAC to generate RGB levels. HSYNC and VSYNC signals are
routed directly from the IPU signal generator pins through IOMUXC.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add WRG and WCLK opcodes to the display controller microcode,
and allow multi instruction codes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds display interface timings for the Television Encoder
connected to IPU DI1 on i.MX53 and adds some configuration
glue code to select which IPU signal generators / pins are to
be used for HSYNC/VSYNC signals.
The default configuration is pin2/pin3 for hsync/vsync. The
VGA connector on i.MX53-QSB uses pin7/pin8, and the analog
part of the DVI-I connector on MBa53 connects to pin4/pin6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
24-bit GBR order is needed on the display interface connected
to the Television Encoder (TVEv2) on i.MX53.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for parsing of the DT display-timings prop
to IPU KMS driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions have been introduced by commit 10a8c383 (irq: introduce
entry and exit functions for chained handlers) in asm/mach/irq.h. This
patch moves them to linux/irqchip/chained_irq.h so that generic irqchip
drivers do not rely on architecture specific header files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
The objects allocated by devm_* APIs are managed by devres and are freed
when the device is detached. There is no need to use kfree() explicitly.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the bootloader already enabled the display, the interrupt handler
will be called as soon as it is registered. If the CRTC is not already
added at this time, the call to imx_drm_handle_vblank will result in
a NULL pointer dereference.
The patch fixes a kernel panic [1], which has been on linux-next since
Jan 8 [2].
[1] http://thread.gmane.org/gmane.linux.ports.arm.kernel/218858
[2] http://thread.gmane.org/gmane.linux.ports.arm.kernel/208192
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when ipuv3 is probed we have:
imx-ipuv3 40000000.ipu: DI0 base: 0x5e040000 remapped to a08aa000
imx-ipuv3 40000000.ipu: DI1 base: 0x5e048000 remapped to a08ac000
imx-ipuv3 40000000.ipu: IPUv3EX probed
The DI base address and the remapped address are more interesting for debug
purposes, so mark this message as dev_dbg instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning when building with W=1 option:
drivers/staging/imx-drm/ipu-v3/ipu-common.c: In function 'ipu_remove':
drivers/staging/imx-drm/ipu-v3/ipu-common.c:1145:19: warning: variable 'res' set but not used [-Wunused-but-set-variable]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kfree(imx_drm_encoder) is already being called at the label
'err_register'.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipu_reset() can fail with a timeout. Check the return value and act
appropriately.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
