Read-modify-write sequence is already protected by regmap, so no
additional locks need. This patch remove such locks from mc13xxx
regulator driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
The nodes of regulators should be retrieved from parent device.
Bug was be introduced by commit (regulator: mc13xxx: Fix NULL
pointer error in non-DT mode) in conjuction with (mfd: Revert
"mfd: Always assign of_node in mfd_add_device()").
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a check to avoid NULL pointer dereference error when
booted in non-DT mode. While at it also remove the additional
of_node_get which is no longer needed for of_get_child_by_name
and fix the node pointer.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a warning about incorrect regulators instead of
printing the names of non-information message about the wrong amount.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
of_find_node_by_name() returns a node pointer with refcount incremented, use
of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against from parameter,
thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Imagine a situation where a device tree has a few regulators in an
appropriate node:
regulators {
sw1 {
..
};
vvideo {
..
};
:
vfake {
..
};
vtypo {
..
};
};
In the above example, the node name "vfake" is an attempt to match a
regulator name inside the driver which just so happens to not exist. The
node name "vtypo" represents an accidental typographical error in a
regulator name which may have been introduced to a device tree.
In these cases, the number of regulators the mc13892 driver thinks it has
does not match the number of regulators it parsed and registered. Since
it will go over this array based on this number, it will actually
re-register regulator "0" (which happens to be SW1) over and over
again until it reaches the number, resulting in messages on the kernel
log such as these:
SW1: at 1100 mV
VVIDEO: at 2775mV
:
SW1: at 1100 mV
SW1: at 1100 mV
.. up to that number of "mismatched" regulators. Nobody using DT can/will
consume these regulators, so it should not be possible for it to cause any
real regulator problems or driver breakages, but it is an easy thing to
miss in a kernel log and is an immediate indication of a problem with the
device tree authoring.
This patch effectively sanity checks the number of counted children of
the regulators node vs. the number that actually matched driver names,
and sets the appropriate num_regulators value. It also gives a little
warning for device tree authors that they MAY have screwed something up,
such that this patch does not hide the device tree authoring problem.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If .is_enabled callback is not implemented, regulator core assumes that the
regulator is always on. Thus we don't need mc13xxx_sw_regulator_is_enabled
function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The voltage range checking should be to ensure mc13xxx_regulators[id].voltages[0]
falls with min_uV and max_uV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert mc13892_sw_regulator_ops and mc13xxx_regulator_ops to set_voltage_sel.
mc13xxx_get_best_voltage_index function is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since mc13xxx-regulator-core.c and the actual drivers can get built
into seperate modules, you have to export the DT support symbols
"mc13xxx_get_num_regulators_dt" and "mc13xxx_parse_regulators_dt"
otherwise the allmodconfig build fails on sparc64.
[Updated the subject; the same thing was previously reported and fixed
in -next but for some reason nobody noticed for some considerable time
after the issue was introduced -- broonie]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It adds device tree probe support for mc13892-regulator driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Another group of drivers that are taking advantage of the implicit
presence of module.h -- and will break when we pull the carpet out
from under them during a cleanup. Fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We use val as array index,
thus the valid value rangae for val should be 0 .. n_voltages-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The variable 'val' is a 'unsigned int', so it can never be less than zero.
This fact makes the "val < 0" part of the test done in BUG_ON() in
mc13xxx_regulator_get_voltage() rather pointles since it can never have
any effect.
This patch removes the pointless test.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since the MFD core for this device and the regulator drivers for these
devices can be built modular we should also support modular build of
the shared code for the regulator drivers, otherwise we try to link
built in code against modular code with unfortunate results.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
