At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
drivers/scsi/libata-core.c | 5 +++--
drivers/scsi/libata-scsi.c | 4 ++--
drivers/scsi/scsi_sysfs.c | 2 +-
include/linux/libata.h | 4 ++--
include/scsi/scsi_host.h | 2 +-
5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() responsible for determining whether to take port
or device offline on failure. ata_dev_set_xfermode() and
ata_dev_set_mode() indicate error to the caller instead of disabling
port directly on failure. Also, for consistency, ata_dev_present()
check is done in ata_set_mode() instead of ata_dev_set_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We may or may not disable a device after ata_dev_configure() fails.
Kill 'not supported, ignoring' message in ata_dev_configure() and use
ata_dev_disable() in ata_bus_probe().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements ata_dev_disable() which prints a warning message
and takes @dev offline. Currently, this is done by explicitly
incrementing dev->class with case-by-case warning messages. Giving
user clear indication when libata gives up will be more important as
libata will be doing more retries.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata core is being changed to disallow port/device disable on lower
layers. However, some LLDDs (sata_mv) directly disable port on
command failure. This patch makes ata_exec_internal() check whether a
port got disabled after an internal command. If it is, AC_ERR_SYSTEM
is added to err_mask and the port gets re-enabled.
As internal command failure results in device disable for drivers
which don't implement newer reset/EH callbacks, this change results in
no behavior change for single device per port controllers. For
slave-possible LLDDs which disable port on command failure, (1) such
drivers don't exist currently, (2) issuing command to the other device
of once-disabled port shouldn't result in catastrophe even if such
driver exists. So, this should be enough as a temporary measure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that each ata_device has xfer masks, per-dev limits can be made
per-dev instead of per-port. Make per-dev limits per-dev.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add per-dev pio/mwdma/udma_mask. All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port. This change will also benefit later EH speed down
and hotplug.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On an ATA error response, take the device down instead of
sending another ATA device identify command.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Always clone incoming skbs, allowing other AoE listeners
to exist in the kernel.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a bugfix that follows and depends on the
eight aoe driver patches sent January 19th.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The aoe driver is not compatible with 2.6 kernels older
than 2.6.2.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of making the user wait or do it manually, refresh
device information on its last close by issuing a config
query to the device.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Users were confused by the driver being called "aoe-2.6-$version".
This form looks less like a Linux kernel version number.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the number of AoE packets per device that can be outstanding
at one time, increasing performance.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow the driver to recognize AoE devices that have changed size.
Devices not in use are updated automatically, and devices that are in
use are updated at user request.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Zero the data in new socket buffers to prevent leaking information.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes old-style kernel thread initialization
and changes w1 to use kthread api.
It is based on Christoph Hellwig <hch@lst.de> work.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
You don't know what type a u64 is, hence you cannot print it without a cast.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The w1 netlink socket is created by a hardware specific driver calling
w1_add_master_device, so there is no point in including a module alias
for netlink autoloading in the core.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
W1_DS9490 was renamed to W1_MASTER_DS9490, but the entry in the
dependencies of W1_MASTER_DS9490_BRIDGE was forgotten.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- make needlessly global code static
- declarations for global code belong into header files
- w1.c: #if 0 the unused struct w1_slave_device
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'blktrace' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] Block queue IO tracing support (blktrace) as of 2006-03-23
[PATCH] relay: consolidate sendfile() and read() code
[PATCH] relay: add sendfile() support
[PATCH] relay: migrate from relayfs to a generic relay API
I encountered the problem that the insmod of the acpiphp
fails because of the mis-freeing of the memory.
I tested this patch on my tiger4 box.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the defines TRUE and FALSE and just uses 0 or 1.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
shpchprm_acpi.c and pciehprm_acpi.c are nearly identical. In addition,
there are functions in both these files that are also in acpiphp_glue.c.
This patch will remove duplicate functions from shpchp, pciehp, and
acpiphp and move this functionality to pci_hotplug, as it is not
hardware specific. Get rid of shpchprm* and pciehprm* files since they
are no longer needed. shpchprm_nonacpi.c and pciehprm_nonacpi.c are
identical, as well as shpchprm_legacy.c and can be replaced with a
macro.
This patch also changes acpiphp to use the common hpp code.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch converts drivers/pci to kzalloc usage.
Compile tested with allyes config.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current ACPIPHP driver scans only slots under the top level PCI-to-PCI
bridge. So hotplug PCI slots under the nested PCI-to-PCI bridge would
not be detected. For example, if the system has the ACPI namespace
like below, hotplug slots woule not be detected.
Device (PCI0) { /* Root bridge */
Name (_HID, "PNP0A03")
Device (P2PA) { /* PCI-to-PCI bridge */
Name (_ADR, ...)
Device (P2PB) { /* PCI-to-PCI bridge */
Name (_ADR, ...)
Device (S0F0) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
...
Device (S0F7) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
Device (S1F0) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
...
}
}
}
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When doing a hotplug removal of a PPB, sn_bus_store_sysdata()
needs to be called for the PPB and all of its children.
Acked-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code related to handling bus speed in SHPCHP driver is
unnecessarily complex. This patch cleans up and simplify that.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing 'const' to pci_request_region[s] 'res_name' arg,
since we pass it directly to __request_region(), whose 'name' arg
is also const.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several drivers are starting to grow options to disable MSI. However,
it's often a host chipset issue, not something which individual drivers
should handle. So we add the pci=nomsi kernel parameter to allow the user
to disable MSI modes for systems we haven't added to the quirk list yet.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the scheduled removal of PCI_LEGACY_PROC.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker correctly noted, that in function board_replaced in
drivers/pci/hotplug/cpqphp_ctrl.c, the variable src always has the
value 8, and therefore much code after the
...
if (rc || src) {
...
if (rc)
return rc;
else
return 1;
}
...
can never be called.
This patch removes the unreachable code in this function fixing kernel
Bugzilla #6073.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hotplug slot is under the host bridge,
DEVICE_ACPI_HANDLE(&bus->self->dev) fails since '&bus->self' was not set.
This patch fixes it.
This patch is based on kristen's latest patches.
I tested this patch on my Tiger4.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o This patch removes IDs (for slots management).
o This patch removes the slot register/unregister processes
from the init/exit phases. Instead, adds these processes
in the bridge add/cleanup phases.
o Currently, this change doesn't have any meanings. But
these changes are needed to support p2p bridge(with
hotplug slot)
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove dock station support from ibm_acpi by default. This support has
been put into acpiphp instead. Allow ibm_acpi to continue to provide
docking station support via config option for laptops/docking stations
that are not supported by acpiphp.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These patches add generic dock event handling to acpiphp. If there are
pci devices that need to be inserted/removed after the dock event, the
event notification will be handed down to the normal pci hotplug event
handler in acpiphp so that new bridges/devices can be enumerated.
Because some dock stations do not have pci bridges or pci devices that
need to be inserted after a dock, acpiphp will remain loaded to handle
dock events even if no hotpluggable pci slots are discovered.
You probably need to have the pci=assign-busses kernel parameter enabled
to use these patches, and you may not allow ibm_acpi to handle docking
notifications and use this patch.
This patch incorporates feedback provided by many.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export the acpi_bus_trim function so that the pci hotplug driver can
use it.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we add a new bridge with subordinate busses, we should call make sure
that acpi is notified so that the PRT (if present) can be read and drivers
who have registered on this bus will be notified when it is started.
Also make sure to use the max reserved bus number for the starting the bus
scan.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as659) fixes a might_sleep problem in the PCI core, by moving
a call to pci_dev_put() outside the scope of a spinlock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"In some cases, especially on modern laptops with a lot of PCI and cardbus
bridges, we're unable to assign correct secondary/subordinate bus numbers
to all cardbus bridges due to BIOS limitations unless we are using
"pci=assign-busses" boot option." -- Ivan Kokshaysky (from a patch comment)
Without it, Cardbus cards inserted are never seen by PCI because the parent
PCI-PCI Bridge of the Cardbus bridge will not pass and translate Type 1 PCI
configuration cycles correctly and the system will fail to find and
initialise the PCI devices in the system.
Reference: PCI-PCI Bridges: PCI Configuration Cycles and PCI Bus Numbering:
http://www.science.unitn.it/~fiorella/guidelinux/tlk/node72.html
The reason for this is that:
``All PCI busses located behind a PCI-PCI bridge must reside between the
secondary bus number and the subordinate bus number (inclusive).''
"pci=assign-busses" makes pcibios_assign_all_busses return 1 and this
turns on PCI renumbering during PCI probing.
Alan suggested to use DMI automatically set assign-busses on problem systems.
The only question for me was where to put it. I put it directly before
scanning PCI bus into pcibios_scan_root() because it's called from legacy,
acpi and numa and so it can be one place for all systems and configurations
which may need it.
AMD64 Laptops are also affected and fixed by assign-busses, and the code is
also incuded from arch/x86_64/pci/ that place will also work for x86_64
kernels, I only ifdef'-ed the x86-only Laptop in this example.
Affected and known or assumed to be fixed with it are (found by googling):
* ASUS Z71V and L3s
* Samsung X20
* Compaq R3140us and all Compaq R3000 series laptops with TI1620 Controller,
also Compaq R4000 series (from a kernel.org bugreport)
* HP zv5000z (AMD64 3700+, known that fixup_parent_subordinate_busnr fixes it)
* HP zv5200z
* IBM ThinkPad 240
* An IBM ThinkPad (1.8 GHz Pentium M) debugged by Pavel Machek
gives the correspondig message which detects the possible problem.
* MSI S260 / Medion SIM 2100 MD 95600
The patch also expands the "try pci=assign-busses" warning so testers will
help us to update the DMI table.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use "unsigned long" when dealing with PCI resources.
The BAR Indicator Register (BIR) can be a 64-bit value
or the resource could be a 64-bit host physical address.
Enables ib_mthca and cciss drivers to use MSI-X on ia64 HW.
Problem showed up now because of new system firmware on one platform.
Symptom will either be memory corruption or MCA.
Second part of this patch deals with "useless" code.
We walk through the steps to find the phys_addr and then
don't use the result. I suspect the intent was to zero
out the respective MSI-X entry but I'm not sure at the moment.
Delete the code inside the #if 0/#endif if it's really
not needed.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out AMD 8131 quirk only affects MSI for devices behind the 8131 bridge.
Handle this by adding a flags field in pci_bus, inherited from parent to child.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller
and MC97 modem controller are deactivated when a second PCI soundcard
is present. This patch enables them.
Signed-off-by: Bauke Jan Douma <bjdouma@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I attach a trivial patch for 2.6.15.4 that unhides SMBus controller
on an HP Compaq nx6110 notebook.
Signed-off-by: Tomasz Koprowski <tomek@koprowski.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The extra compatability code is not necessary. Any code still using
the old shutdown method will trigger the warning in driver_register()
instead.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't care about the confliction between
hotplug operation via sysfs and hotplug operation via attention
button. So if those ware conflicted, slot could be an unexpected
state.
This patch changes SHPCHP driver to handle slot state properly. With
this patch, slot events are handled according to the current slot
state as shown at the Table below.
Table. Slot States and Event Handling
=========================================================================
Slot State Event and Action
=========================================================================
STATIC - Go to POWERON state if user initiates
(Slot enabled, insertion request via sysfs
Slot disabled) - Go to POWEROFF state if user initiates removal
request via sysfs
- Go to BLINKINGON state if user presses
attention button when the slot is disabled
- Go to BLINKINGOFF state if user presses
attention button when the slot is enabled
The event handler of SHPCHP driver is unnecessarily very complex. In
addition, current event handler can only a fixed number of events at
the same time, and some of events would be lost if several number of
events happened at the same time.
This patch simplify the event handler by using 'work queue', and it
also fix the above-mentioned issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wait_for_ctrl_irq() function in SHPCHP driver is no longer needed.
This patch removes that. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unused 'pci_bus' member from controller structure.
This patch have no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> On Mon, Feb 13, 2006 at 05:13:21PM -0800, David S. Miller wrote:
> >
> > In drivers/pci/probe.c:pci_scan_bridge(), if this is not the first
> > pass (pass != 0) we don't restore the PCI_BRIDGE_CONTROL_REGISTER and
> > thus leave PCI_BRIDGE_CTL_MASTER_ABORT off:
> >
> > int __devinit pci_scan_bridge(struct pci_bus *bus, struct pci_dev * dev, int max, int pass)
> > {
> > ...
> > /* Disable MasterAbortMode during probing to avoid reporting
> > of bus errors (in some architectures) */
> > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &bctl);
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> > bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
> > ...
> > if ((buses & 0xffff00) && !pcibios_assign_all_busses() && !is_cardbus) {
> > unsigned int cmax, busnr;
> > /*
> > * Bus already configured by firmware, process it in the first
> > * pass and just note the configuration.
> > */
> > if (pass)
> > return max;
> > ...
> > }
> >
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, bctl);
> > ...
> >
> > This doesn't seem intentional.
Agreed, looks like an accident. The patch [1] originally came from Kip
Walker (Broadcom back then) between 2.6.0-test3 and 2.6.0-test4. As I
recall it was supposed to fix an issue with with PCI aborts being
signalled by the PCI bridge of the Broadcom BCM1250 family of SOCs when
probing behind pci_scan_bridge. It is undeseriable to disable
PCI_BRIDGE_CTL_MASTER_ABORT in pci_{read,write)_config_* and the
behaviour wasn't considered a bug in need of a workaround, so this was
put in probe.c.
I don't have an affected system at hand, so can't really test but I
propose something like the below patch.
[1] http://www.linux-mips.org/git?p=linux.git;a=commit;h=599457e0cb702a31a3247ea6a5d9c6c99c4cf195
[PCI] Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver has a bug in its interrupt handler which cause
"IRQ #: nobody cared" oops. This problem can be reproduced easily by
the following operation.
# cd /sys/bus/pci/slots/<slot#>
# while true; do echo 1 > attention ; done &
The reason is that when command complete interrupt is raised, current
SHPCHP driver's interrupt handler returns IRQ_NONE regardless of if
the interrupt is handled or not.
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves slot name area into struct slot.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unnecessary 'magic' member from struct slot of
SHPCHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces kmalloc() and memset() pair with kzalloc() and
cleans up the arg of sizeof() in SHPCHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up pcihp_skelton.c as follows.
o Move slot name area into struct slot.
o Replace kmalloc with kzalloc and clean up the arg of sizeof()
o Fix the wrong use of get_*_status() functions.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver might cause system panic because of lack of
serialization. It can be reproduced very easily by the following
operation.
# cd /sys/bus/pci/slots/<slot#>
# while true; do echo 0 > power ; echo 1 > power ; done &
# while true; do echo 0 > power ; echo 1 > power ; done &
This patch fixes this issue by changing shpchp to get appropreate
semaphore for hot-plug operation.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups codes that check the command status. For this, it
introduces a new semaphore "cmd_sem" for each controller.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups some codes in shpchp_core.c. This patch has no
functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups init_slots() function of SHPCHP driver based on
pcihp_skelton.c. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested with allyesconfig.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IBM Dock II cardbus bridges require some extra configuration
before Yenta is loaded in order to setup the Interrupts to be
routed properly.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After you find the maximum value of the subordinate buses below the child
bus, you must fix the parent's subordinate bus number again, otherwise
it may be too small.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the semantics of this call to return the max reserved
bus number instead of just the max assigned bus number.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up: move assignments outside of if() statements.
AFAICT, no functional change. Easier to read/understand.
Depends on "[PATCH 1/3] msi vector targeting abstractions"
by Mark Maule <maule@sgi.com>.
I expect one hunk to fail if applied against 2.6.15.
This is essentially Joe Perches' patch.
I've cleaned up the one instance added by Mark's patch.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add required locking around idr_ routines, retry the idr_pre_get/idr_get_new
pair properly, and sprinkle in some likely/unlikely for good measure.
(Lack of idr locking didn't hurt when all callers were I2C clients, as the
i2c-core serialized for us anyway. Now that we have non I2C hwmon drivers,
this is truly necessary.)
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"register" is a reserved keyword so using it as a parameter name
can confuse some compilers, most notably ICC.
The patch below just renames all occurences to reg which fits the actual
function declarations.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several media/video and sound drivers include i2c-dev.h while they
don't need it at all. Clean it up.
This header file is really only needed by i2c-dev.c and
compat_ioctl.c, other drivers should never need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds I2C_CLASS_HWMON to the ixp4xx bus driver.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Broadcom HT-1000 south bridge's PCI ID to i2c-piix driver. Note
that at least on Supermicro H8SSL it uses non-standard SMBHSTCFG = 3
and standard values like 0 or 9 causes hangup.
Signed-off-by: Martin Devera <devik@cdi.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop a redundant mutex in driver i2c-ali1535. The struct i2c_adapter
includes a mutex for the same purpose, operated by i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop unused rogue i2c driver ID and nonsensical i2c class.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly set the name member of the i2c_adapter structure of the ite
i2c adapter driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the i2c-frodo bus driver. It isn't referenced by the build
system, and depends on code which was never included in 2.6 kernels.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop holding the core_lists mutex when we don't actually need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop resetting the chip on load by default, so as to preserve the BIOS
initializations. Same was done in the w83627hf driver some times ago
for the same reasons.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamic sysfs callbacks and array of attributes to reduce the
w83627ehf driver size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Intel Pentium M series to the hwmon-vid driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Winbond W83687THF chip to the w83627hf hardware
monitoring driver. This new chip is almost similar to the already
supported W83627THF chip, except for VID and a few other minor
changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the new f71805f hardware monitoring driver to use mutexes
instead of semaphores.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
convert drivers/hwmon/*.c semaphore use to mutexes.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
all affected hwmon drivers were build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup after the semaphores to mutexes conversions in the i2c
subsystem.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Speed up i2c_smbus_write_block_data and i2c_smbus_read_i2c_block_data
a bit by using memcpy instead of an explicit loop.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop 3 useless macros in the w83792d hardware monitoring driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use arrays of attributes in the w83792d driver.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Yuan Mu <ymu@winbond.com.tw>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
scx200_acb is only useful on a few Geode-based systems, and won't
compile on non-x86 systems due to the lack of asm/msr.h, as reported
by Andrew Morton. Thus, we should make that driver depend on X86.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
scx200_acb: Fix and speed up the poll loop
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
scx200_acb: remove use of lock_kernel()
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below converts a few i2c semaphores to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the f71805f driver to use arrays of attributes. This shrinks the
compiled module from 12.0 kB to 9.6 kB. We certainly should do the same
for as many hardware monitoring drivers as possible.
This, together with a nice chip design by Fintek, makes this driver
very small, both in terms of number of lines of code and memory
consumption.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert individual sensors to sensor-attr arrays by each sensor type,
and initialize them in loops instead of long blocks of individual calls.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't need to keep track of available buffers, it is simpler
to just compute the value (ala e1000). Don't need tes on link up
because should always have available buffers then.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't free transmit buffers until the whole set of transmit descriptors
has been marked as done. Otherwise, we risk freeing a skb before the
whole transmit is done.
This changes the transmit completion handling from incremental to a
two pass algorithm. First pass scans and records the start of the last
done descriptor, second cleans up until that point.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the error case we call skge_rx_reuse twice. This is harmless
but unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver was using dev_alloc_skb which reserves space for the
Ethernet header. This unnecessary and it should just use alloc_skb,
also by using GFP_KERNEL during startup it won't run into problems when
a user asks for a huge ring size or mtu and potentially drains the
reserved atomic pool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver aligns the header on the initial receive buffers, but
but doesn't on followon receive buffer allocations.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unicast packets are shown as multicast, real multicast packets are missing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker (CID: 659, 660) spotted this resource leak on
PCI probe error path. Free private data structure if pci_enable_device()
fails.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 58) spotted this duplicated idx != 0
validation for unicast keys in prism2_ioctl_siwencodeext().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 452, 453, 454, 455, 456) spotted this
unlikely read overrun of CIS buffer. Abort if CISTPL_CONFIG or
CISTPL_MANFID would not fit in buffer.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 930) spotted this double free on error path
(allocation failure). Do not free these here since generic error path
will take care of this.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 273) spotted this inconsequent NULL checking
(unconditionally dereferencing directly after checking for NULL
isn't a good idea). Return immediately to avoid this.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 59) noted that the call to prism2_hw_reset()
was dead code. Move prism2_hw_reset() call to a place where it is
actually executed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Observed problems when multiple processes request scans and subsequently
scan results. This causes a scan result request to hit card registers
before the scan is complete, returning an incomplete scan list and
possibly making the card very angry. Instead, cache the results of a
wireless scan and serve result requests from the cache, rather than
hitting the hardware for them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number 2312 was used all over the place to refer to the card's
default MTU. Make it a #define and use that everywhere rather than the
number.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the specific device that driver messages are about.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without the attached, the kernel complains about my BIOS' PNP tables. It
was ACKed before, but never merged:
http://marc.theaimsgroup.com/?l=linux-kernel&m=110237794007900&w=2
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes all occurances of _INLINE_ in the kernel.
With the exception of tty_flip.h, I've simply removed the inline's since
gcc should know best which functions to be inlined.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change driver to use kzalloc rather than kmalloc+memset
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert from semaphore to mutex.
Untested as I have no access to a floppy drive at the moment.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert to use mutex from a semaphore
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since early 2.4.x all cdrom drivers implement the block_device methods
themselves, so they can handle additional ioctls directly instead of going
through the cdrom layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a small helper for each ioctl to cut down cdrom_ioctl to a readable
size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is unsafe to suspend devices if the hardware is controlled by X. Add an
extra check to prevent this from happening.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all the Zoran (ZR36050/ZR36060) drivers to use i2c_master_send instead
of i2c_transfer when possible. This simplifies the code by a few lines in
each driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop support for the ENCODER_DUMP command in the adv7175 driver. ENCODER_DUMP
was never actually defined as far as I can see, so the code was ifdef'd out,
and I suspect it was never used, not even once, as it includes an obvious
array overrun.
The register values of this specific chip can be dumped in a generic way using
the i2c-dev driver and the "i2cdump" user-space tool if it is ever really
needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop the adv7175 register cache, as it is only written to and never read back
from. This saves 128 bytes of memory and slightly speeds up the register
writes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a (probably harmless) array overrun in the DECODER_DUMP command of the
saa7110 driver. No big deal as this command is not used anywhere anyway.
Also reformat the dump so that it displays nicely.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bt856 driver has a register cache much larger than needed. We really only
write to 3 registers, so a 32-byte cache is a bit too much. We can be just as
efficient with a 6-byte cache. We could even do with a 3-byte cache, but at
the cost of additional arithmetics arguably not worth the spared 3 bytes.
Also, 4 of the 6 other members of the bt856 data structure were not used
anywhere, so we can as well drop them for an additional 16 bytes of memory
spared.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When grabbing composite video with Iomega Buz, the stock driver will
prevent grabbing from the same input twice in a row, forcing the user to
switch inputs before anything useful can be grabbed again. It is caused by
some optimization code in the input selection parts, and triggered by the
saa7111_command() executing cmd 0. The attached patch will remedy this by
disabling cmd 0 altogether; a fix that has no found negative effects on the
rest of the code. In fact, saa7110.c does the exact same thing.
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanups to the zr36057 initialization:
* Drop intermediate local variables.
* Single error path.
Also drop a needless cast on kfree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Explicitely state the number of registers the SAA7111 has, and use that
defined value where relevant. This should prevent any future array overrun
like the one I just fixed in the saa7110 driver.
This patch also saves 8 bytes of memory as a side effect, as the register
cache was larger than needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the i2c block write mode of the saa7114 driver. A previous code change
accidentally commented out a local variable increment, which should have been
kept, causing the register writes over the I2C bus to never be batched,
replacing any attempted block write by slower, individual write transactions.
Also drop the commented out code, as it only adds to confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is version 20 of the Wireless Extensions. This is the
completion of the RtNetlink work I started early 2004, it enables the
full Wireless Extension API over RtNetlink.
Few comments on the patch :
o totally driver transparent, no change in drivers needed.
o iwevent were already RtNetlink based since they were created
(around 2.5.7). This adds all the regular SET and GET requests over
RtNetlink, using the exact same mechanism and data format as iwevents.
o This is a Kconfig option, as currently most people have no
need for it. Surprisingly, patch is actually small and well
encapsulated.
o Tested on SMP, attention as been paid to make it 64 bits clean.
o Code do probably too many checks and could be further
optimised, but better safe than sorry.
o RtNetlink based version of the Wireless Tools available on
my web page for people inclined to try out this stuff.
I would also like to thank Alexey Kuznetsov for his helpful
suggestions to make this patch better.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for new chip 5755 which is very similar to 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the tx producer and consumer fields in separate cache lines in
the device structure, similar to the VJ net channel queue structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine two small (56 byte and 320 byte) pci consistent memory
allocations into one allocation. Jeff Garzik suggested to store
the combined size in the bp structure for later use when freeing
the memory.
Use kzalloc() instead of kmalloc() + memset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some link-related problems by doing a coalesce_now after link
change interrupt to flush out the transient link status.
To facilitate this, the host coalesce cmd register value is cached in
the device structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sata_uli was storing PCI config addresses in a variable intended for
port addresses, a variable soon to become void __iomem *.
Update the driver to store the SCR address, found in PCI config space,
in the driver-private data area.
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
All callers of macio_register_driver() either ignore the return value or
return it as the return value of a module_init() function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Nobody uses the return value of of_register_driver() anyway.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/macintosh/via-pmu.c:164: warning: `sleep_in_progress' defined but not used
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the use of i2c headers in macintosh drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now powerpc uses the generic RTC stuff we should not enable the old RTC.
Doing so will result in hangs at boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerbook_sleep_grackle is only called inside via-pmu, from pmu_ioctl()
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
this fixes coverity bug #912, where skb is freed first,
and dereferenced a few lines later with skb->len.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router".
From: Ursula Braun <braunu@de.ibm.com>
when setting route6 attribute back to no_router qeth does not
issue an IP ASSIST command to reset router value to no_router.
Once primary_router is set device stays in this mode.
Issue an IP ASSIST command when no_router is set in route6.
Device will be reset and thus will not longer run as a primary
router.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 5 -----
1 files changed, 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 3/6] s390: qeth driver cleanups
From: Ursula Braun <braunu@de.ibm.com>
- code analyzing tool BEAM has found some unreachable
and unnecessary statements and also conditions
which are always true.
- removed some useless MII code since OSA card will never
allow to set such values.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 49 ++++---------------------------------------------
qeth_proc.c | 18 +++++++++---------
qeth_sys.c | 2 +-
3 files changed, 14 insertions(+), 55 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add a secondary TSB for hugepage mappings.
[SPARC]: Respect vm_page_prot in io_remap_page_range().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Bump driver version and reldate.
[TG3]: Skip phy power down on some devices
[TG3]: Fix SRAM access during tg3_init_one()
[X25]: dte facilities 32 64 ioctl conversion
[X25]: allow ITU-T DTE facilities for x25
[X25]: fix kernel error message 64 bit kernel
[X25]: ioctl conversion 32 bit user to 64 bit kernel
[NET]: socket timestamp 32 bit handler for 64 bit kernel
[NET]: allow 32 bit socket ioctl in 64 bit kernel
[BLUETOOTH]: Return negative error constant
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace. This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.
Move over to the preferred way, that is, using compound pages instead. This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure. However, that is not what happens. The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap(). Cache_reap()
is run every few seconds independently of memory pressure.
Could we remove the whole thing? Its only used by three slabs anyways and
I cannot find a reason for having this option.
There is an additional problem with SLAB_NO_REAP. If set then the recovery
of objects from alien caches is switched off. Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk. (Strangely __cache_shrink does not
check for SLAB_NO_REAP)
Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away, define
dcdbas_driver and implement ->probe() and ->remove() functions so manual
binding and unbinding will work with this driver.
Also switch to using attribute_group when creating sysfs attributes and
make sure to check and handle errors; explicitely remove attributes when
detaching driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mv64x600_wdt: convert to the new platform device interface Do not use
platform_device_register_simple() as it is going away.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch does the following for v441xx seris drivers:
- stop using platform_device_register_simple() as it is going away
- mark ->probe() and ->remove() methods as __devinit and __devexit
respectively
- initialize "owner" field in driver structure so there is a link
from /sys/modules to the driver
- mark *_init() and *_exit() functions as __init and __exit
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the serial_txx9 driver.
* More strict check in verify_port. Cleanup.
* Do not insert a char caused previous overrun.
* Fix some spin_locks.
* Do not call uart_add_one_port for absent ports.
Also, this patch removes a BROKEN tag from Kconfig. This driver has been
marked as BROKEN by removal of uart_register_port, but it has been solved
already on Sep 2005.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that handles bios that span table target boundaries by breaking
them up into smaller bios will not split an individual struct bio_vec into
more than two pieces. Sometimes more than that are required.
This patch adds a loop to break the second piece up into as many pieces as
are necessary.
Cc: "Abhishek Gupta" <abhishekgupt@gmail.com>
Cc: Dan Smith <danms@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The console cursor can be called in atomic context. Change memory
allocation to use the GFP_ATOMIC flag in i810fb_cursor().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.
Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."
I fixed this by adding a check for zero. While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The first performs the simplex clearing relevant to some chipsets that
report simplex by default but can in fact do more if poked. The second
is used to strip DMA modes from a PCI control with no BAR4 allocation.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses a number of weird behaviours observed
for the sata_mv driver, by fixing an "off by one" bug in processing
of the EDMA response queue.
Basically, sata_mv was looking in the wrong place for
command results, and this produced a lot of unpredictable behaviour.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Encapsulate some of ata_scsi_slave_config so that parts
can be reused in future SAS patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch (and description) by Douglas Gilbert, with minor fixes
and API updates from me.
Changelog:
- make existing libata VPD device identification page (0x83)
supply the ATA serial number in the libata "vendor
specific" designator (from Chris Paulson-Ellis)
- add a "t10 vendor id based" designator as defined in
SAT rev 08 (section 10.3.4.2.3) that supplies ATA
model and serial numbers
- make the libata VPD page 0x83 more extensible (for
adding more designators in the future).
- rename EVPD to VPD in various places. Enable Vital
Product Data (EVPD) is a bit in the INQUIRY cdb.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64-SGI] SN2-XP reduce kmalloc wrapper inlining
[IA64] MCA: remove obsolete ifdef
[IA64] MCA: update MCA comm field for user space tasks
[IA64] MCA: print messages in MCA handler
[IA64-SGI] - Eliminate SN pio_phys_xxx macros. Move to assembly
[IA64] use icc defined constant
[IA64] add __builtin_trap definition for icc build
[IA64] clean up asm/intel_intrin.h
[IA64] map ia64_hint definition to intel compiler intrinsic
[IA64] hooks to wait for mmio writes to drain when migrating processes
[IA64-SGI] driver bugfixes and hardware workarounds for CE1.0 asic
[IA64-SGI] Handle SC env. powerdown events
[IA64] Delete MCA/INIT sigdelayed code
[IA64-SGI] sem2mutex ioc4.c
[IA64] implement ia64 specific mutex primitives
[IA64] Fix UP build with BSP removal support.
[IA64] support for cpu0 removal
This reverts commit 08f1d0b99f
The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated
all the way to this tree, so the Makefile change escaped too soon.
Build breakage noticed by Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
