We normally trust and use the CDC functional descriptors provided by a
number of devices. But some of these will erroneously list the address
reserved for the device end of the link. Attempting to use this on
both the device and host side will naturally not work.
Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:
321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request id=0x4025, seq=64/16384, ttl=64
0000 82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00 .....g.....g..E.
0010 00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a .T..@.@.W.M.U..z
0020 ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00 ....b.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply id=0x4025, seq=64/16384, ttl=55
0000 00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00 .......P......E.
0010 00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10 .T.V..7..v.z..M.
0020 55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00 U...j.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
The bogus address is always the same, and matches the address
suggested by many devices as a default address. It is likely a
hardcoded firmware default.
The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset. A procedure most users are likely to try out before
reporting a bug.
Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit. The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.
This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.
All devices supported by this driver have severely limited
networking capabilities:
- can only transmit IPv4, IPv6 and possibly ARP
- can only support a single host hardware address at any time
- will only do point-to-point communcation with the host
Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits. All we need to
do is to avoid 4 or 6 in the first digit of the mac address. This
workaround ensures this, and fix up the received packets as necessary.
Given the distribution of the bug, it is believed that the source is
the chipset vendor. The devices which are verified to be affected are:
Huawei E392u-12 (Qualcomm MDM9200)
Pantech UML290 (Qualcomm MDM9600)
Novatel USB551L (Qualcomm MDM9600)
Novatel E362 (Qualcomm MDM9600)
It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.
The information about affected devices and versions is likely
incomplete. As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_addr_lock_bh() to acquire the appropriate lock before walking.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_disable_netpoll() is not called upon enslave failure which would
lead to a memory leak. Call slave_disable_netpoll() after err_detach as
that's the first error path after enabling netpoll on that slave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.
v2: update log message and don't move code unnecessarily
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the get_settings ethtool op to the bonding
driver. This was motivated by users who wanted to get the speed of the
bond and compare that against throughput to understand utilization.
The behavior before this patch was added was problematic when computing
line utilization after trying to get link-speed and throughput via SNMP.
Output from ethtool looks like this for a round-robin bond:
Settings for bond0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 11000Mb/s
Duplex: Full
Port: Other
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Link detected: yes
I tested this and verified it works as expected. A test was also done
on a version backported to an older kernel and it worked well there.
v2: Switch to using ethtool_cmd_speed_set to set speed, added check to
SLAVE_IS_OK for each slave in bond, dropped mode-specific calculations
as they were not needed, and set port type to 'Other.'
v3: Fix useless assignment and checkpatch warning.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When mailbox interrupt is disabled PF should be
able to process request from VF. Enable polling
for such cases.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not disable mailbox interrupts while running
loopback test through SR-IOV PF.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for VLAN id configuration per VF using
iproute2 tool.
o VLAN id's 1-4094 are treated as PVID by the PF and
Guest VLAN tagging is not allowed by default.
o PVID is disabled when the VLAN id is set to 0
o Guest VLAN tagging is allowed when the VLAN id is set to 4095.
o Only one Guest VLAN id is supported.
o VLAN id can be changed only when the VF driver is not loaded.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for MAC address and Tx rate configuration
per VF via iproute2 tool.
o Tx rate change is allowed while the guest is running
and the VF driver is loaded.
o MAC address change is allowed only when VF driver
is not loaded.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Implement recovery mechanism for VF to recover from
adapter resets.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o FLR from Hypervisor - When hypervisor issues a VF FLR request,
adapter notifies the parent PF driver of the FLR request for PF
driver to perform any cleanup on behalf of that VF.
o FLR from VF Driver - VF driver may initiate a VF FLR request,
if VF state needs to be cleaned up before a re-initialization.
VF re-initialization during kdump is an example.
o PF driver cleans up all resources allocated on behalf of a VF,
on VF FLR notifications from the adapter or from the VF driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 82xx adapter requires VLAN id in little endian format.
Instead of passing vlan id parameter as __le16, pass the
parameter as u16 and use cpu_to_le16 at appropriate places.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- macvlan: propagate STAG filtering capabilities from underlying device
- ifb: announce STAG tagging support in addition to CTAG tagging support
- veth: announce STAG tagging/stripping support in addition to CTAG support
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
A few stragglers hoping for 3.9, somewhat delayed due to my travels...
On the mac80211 bits, Johannes says:
"Sadly, I have another pull request -- the idle handling fix broke LED
handling in some cases."
and:
"Yet one more!
This fixes a fairly important/annoying bug -- when roaming between
multiple APs of the same network, the system could get stuck thinking it
was connected to the old one while it really wasn't."
On top of that...
Arend sends a brcmfmac patch that removes advertising a feature that
isn't actually fully supported, and a brcmsmac patch that rearranges
code to request firmware at IFF_UP to play more nicely with being
built into the kernel.
Felix gives us a minor ath9k_htc fix to support the newly released
open source firmware, and an ath9k_hw initvals fix to improve device
stability.
Rafał Miłecki provides a fix for an ssb regression that caused a
serious performance problem with b43.
Zefir Kurtisi offers an ath9k fix to change some kmalloc flags to
allow the DFS detector to be called in softirq context.
Please let me know if there are problems. If these don't make 3.9,
I'll just pull them into wireless-next -- just let me know if you
want to do it that way!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds base support for new i354 devices. Loopback test is
unsupported for this release.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for spoofchk configuration per VF via iproute2 tool.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On EEE-capable devices, query the PHY to determine what the link partner is
advertising.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aligns the multi-line code comments with the desired style for the
networking tree. Also cleaned up whitespace issues found during the
cleanup of code comments (i.e. remove unnecessary blank lines,
use tabs where possible, properly wrap lines and keep strings on a
single line)
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
This patch fixes sparse warnings on function pointers that are not
defined as static.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It turns out that the InterruptThrottleRate module parameter was only
having the effect of locking the ITR at the starting ITR value. This was
because the values stored in rx_itr_setting and tx_itr_setting were being
ignored when configuring the initial itr_val of the q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We only need the adapter pointer in the case of ptp. As such we can pull the
adapter out of the main path and place it inside the if statement to avoid
the temptation of accessing the adapter pointer in the fast path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset. As a result we were not pulling in TCP headers when the DNF
flag was set.
To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes code and comments as identified in the driver.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on original patch from Aurélien Guillaume <footplus@gmail.com>
This patch adds support to turn on I2C, with sfp cage powered.
CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support to read and export SFF-8472/8079 (SFP data)
over i2c, through Ethtool.
v2: Changed implementation to accommodate any offset within SFF module
length boundary.
Reported-by: Aurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 100base-fx SFP and report proper link speed/duplex
via Ethtool.
v2: fix smatch warnings
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add some empty static inlines instead to make
the code more readable.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds software support for WoL for the 82599 SFP+ LOM device,
(ID 0x8976)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 6b923cb718 (bonding: support for IPv6 transmit hashing)
bonding doesn't properly hash traffic in forwarding setups.
Vitaly V. Bursov diagnosed that skb_network_header_len() returned 0 in
this case.
More generally, the transport header might not be in the skb head.
Use pskb_may_pull() & skb_header_pointer() to get it right, and use
proto_ports_offset() in bond_xmit_hash_policy_l34() to get support for
more protocols than TCP and UDP.
Reported-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: John Eaglesham <linux@8192.net>
Tested-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes 2 issues regarding bnx2x's status blocks:
1. ethtool -c caused corruption of status blocks in FW RAM.
2. when using multi-CoS, the configuration of the timeout values of
status blocks is incorrect, harming the coalescing of interrupts
for such CoSs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading after UNDI (e.g., Boot from SAN) the UNDI does not
gracefully yield its resources; The bnx2x driver handles that release
itself.
During the manipulation required to release those resources, it's possible
for the UNDI to try and write to memory regions which are no longer accessible,
causing the PCI bus to prevent further writes from the chip.
This would in turn cause DMAE timeouts later on in the driver, as the driver
will be unable to use the chip's DMA engines.
This patch prevents the chip from actually writing through the PCI bus
in said scenario, thus allowing the release without the unfortunate by-product.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe only.
v2- Dropped the following 2 patches from the series:
ixgbe: Support using build_skb in the case that jumbo frames are disabled
ixgbe: walk pci-e bus to find minimum width
Ben Hutchings found a bug with Alex's patch, so that patch was dropped
permanently. Jacob's "walk PCIe bus" patch is being re-worked for
a more generic solution so that other drivers can benefit.
In the remaining patches...
Alex provides a fix where we were incorrectly checking the entire frag_off
field when we only wanted the fragment offset. Alex also cleans up
the check for PAGE_SIZE, since the default configuration allocates 32K
for all buffers.
Emil provides a change to the calculation of eerd so that it is consistent
between the read and write functions by using | instead of +.
Jacob adds support for displaying PCIe Gen3 link speed, which was
previously missing from the ixgbe driver. He also provides a patch
to clean up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in another patch provided by Jacob.
Jacob modifies the driver to enable certain devices (which have an
internal switch) to read from the physical slot rather than reading
data from the internal switch.
Don provides a couple of fixes (which are more appropriate for net-next),
one of which resolves an issue where ixgbe was only turning on the laser
when the adapter was up which caused issues for those who wanted to
access the MNG firmware while the port was in a down state. The other
fix is for WoL when currently linked at 1G. Lastly Don bumps the driver
version keep the in-kernel driver up to date with the current functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the driver that requires <asm/coldfire.h> and
<asm/mcfsim.h>.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Debug logs were not matching with code functionality.
o Changed dev_info to netdev_err
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver receives a packet with gso size > 0 and when TSO is disabled,
it should be transmitted as a TSO packet to prevent Tx timeout and subsequent
firmware reset.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before conducting loopback test by sending packets, driver should stop transmit
queue and turn off carrier.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver does not check if the administrator has already set a VF
VLAN via the PF driver before setting the new VLAN. This results in
the following scenario:
A) Administrator sets VF <n> to VLAN 100
B) Administrator sets VF <x> to VLAN 100
C) Administrator sets VF <n> to VLAN 200
D) The VF <n> driver continues to be able to receive traffic on VLAN
100 because the VLVFB pool enable bit for that VF was left set
instead of being cleared as it should be.
This fix ensures that the old VLAN filter for VF <n> is first removed
and the pool bit enable for VF <n> is cleared so that it no longer
receives traffic on VLAN 100.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch actually reverts:
igb: Support using build_skb in the case that jumbo frames are disabled
The reason for reverting this patch is that it can lead to data corruption.
The following flow was pointed out by Ben Hutchings:
1. skb is forwarded to another device
2. Packet headers are modified and it's put into a queue
3. Second packet is received into the other half of this page
4. Page cannot be reused, so is DMA-unmapped
5. The DMA mapping was non-coherent, so unmap copies or invalidates
cache
The headers added in step 2 get trashed in step 5.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another ID for a 7000 series device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the stations are being restored because of unassoc
RXON, the LQ cmd may not have been initialized because it
is initialized only after association.
Sending zeroed LQ_CMD makes the fw unhappy: it raises
SYSASSERT_2078.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[move zero_lq and make static const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make power management in MVM driver enabled by default and
remove using the power_save module parameter. Rely only on
the power_scheme parameter to decide if power management
should be used.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can check buf against NULL instead of having additional bool
variable.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If on iwl_dump_nic_event_log() error occurs before that function
initialize buf, we process uninitiated pointer in
iwl_dbgfs_log_event_read() and can hit "BUG at mm/slub.c:3409"
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=951241
Cc: stable@vger.kernel.org
Reported-by: ian.odette@eprize.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bump the version number reflect the corresponding functionality in the
out of tree driver.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We reset during the shutdown path which will reset AUTOC register. This
would change LMS to 10G. If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work. For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were only turning the laser on when the adapter was up. This
causes issues for those who wanted to access the MNG FW while the
port was in a down state. This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver to enable certain devices, which have an internal
switch, to read data from the physical slot rather than reading data from the
internal switch. The internal switch will always report the same PCI width and
speed, which is not useful compared to knowing the width and speed of the slot
the physical card is plugged into.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in a follow on patch that needs to convert
between the link_status PCIe config values into ixgbe's internal enum
representations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers. Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset. As a result we were not pulling in TCP headers when the DNF
flag was set.
To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove warning introduced by commit 418fc57 ("usbnet: cdc-ether: apply
usbnet_link_change"):
CHECK .../drivers/net/usb/cdc_ether.c
.../drivers/net/usb/cdc_ether.c:409:46: warning: incorrect type in argument 2 (different base types)
.../drivers/net/usb/cdc_ether.c:409:46: expected bool [unsigned] [usertype] <noident>
.../drivers/net/usb/cdc_ether.c:409:46: got restricted __le16 [usertype] wValue
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commit 319ecf121e
("qlcnic: 83xx sysfs routines") introduced regression
for beaconing test while refactoring 82xx code. This patch is to
revert code to fix beaconing test for 82xx adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7b7a2bbb69 (atl1: Remove unneeded PM_OPS definitions) removed the
definition of atl1_suspend for the !CONFIG_PM_SLEEP case.
So only call atl1_suspend() when CONFIG_PM_SLEEP is defined and fix the
following build error from randconfig:
drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_shutdown':
drivers/net/ethernet/atheros/atlx/atl1.c:2888:2: error: implicit declaration of function 'atl1_suspend' [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A link-down isn't properly saved in the FEC state, so we wouldn't restart the
FEC after a repeated link-up.
Regression was introduced with commit
d97e7497 "net: fec: restart the FEC when PHY speed changes"
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention was to test against the constant, not the size of
the constant.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. It consists of a patch by
Oliver Hartkopp. In this patch he cleans up the sja1000 header file by
using a common prefix for all sja1000 defines.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.
Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we can't _up() after changing the MTU, report the actual error instead
of -ENOMEM. It can be really misleading cause pch_gbe is usually used in
scenarios where the memory amount is really small, and thus hiding the
real cause.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.
v4: generalize struct vxlan_dev, "gaddr" is replaced with vxlan_rdst.
"GROUP" attribute is replaced with "REMOTE".
they are based by David Stevens's comments.
v3: move a new attribute REMOTE into the last of an enum list
based by Stephen Hemminger's comments.
v2: use a new attribute REMOTE instead of GROUP based by
Cong Wang's comments.
Signed-off-by: Atzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the work has been scheduled from interrupt, and not been
cancelled when the driver is unloaded, which doesn't remove
the work item from the global workqueue. call the
cancel_work_sync when the driver is removed (rmmod'ed).
Cc: Sriram <srk@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Vinay Hegde <vinay.hegde@ti.com>
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.
With irq_type configuration set to 0 the original behavior is
preserverd.
Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Conflicts:
drivers/net/ieee802154/at86rf230.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Cc: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently in low power (LP) mode FW moved from active to power save mode
after TX/RX completion faster than in balanced power mode (BPS).
Change AM-to-PSM transition time so that it will be the same as for BPS.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
first_antenna is supposed to return the first antenna as a
0-based bitmap: ANT_A is BIT(0), ANT_B is BIT(1), etc...
Since ffs is 1 based (ffs(BIT(0)) = 1), then we had an
off-by-one bug:
BIT(ffs(ANT_A)) = BIT(ffs(BIT(0))) = BIT(1) = ANT_B.
So what we really want is:
BIT(ffs(ANT_A) - 1) = BIT(ffs(BIT(0)) - 1) = BIT(0) = ANT_A.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chain noise is done in the firmware and Bluetooth Coexistence
is implemented now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a follow up patch to:
f901b6b can: sja1000: fix define conflict on SH
That patch fixed a define conflict between the SH architecture and the sja1000
driver, by addind a prefix to one macro only. This patch consistently renames
the prefix of the SJA1000 controller registers from "REG_" to "SJA1000_".
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Team drivers attempts to sync addresses to each of the port
devices; however, the current api doesn't really perform the sync
for any device after the first one. Switch to using the new api
that will actually sync the addresses to all ports.
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual EMAC slave VLAN id must be got from slave node instead of cpsw node as
VLAN id for each slave will be different.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Original-idea-by: <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx() was using a static tx queue number causing crashes as
soon as a little bit of traffic was sent via the interface, because
it is normally expected that the same queue should be used as in
dev_queue_xmit().
As suggested by Ben Hutchings, let's use skb_get_queue_mapping() to
get the proper Tx queue number, and use alloc_etherdev_mqs() instead
of alloc_etherdev_mq() to create the queues.
Both my Mirabox and my OpenBlocks AX3 used to crash without this patch
and don't anymore with it. The issue appeared in 3.8 but became more
visible after the fix allowing GSO to be enabled.
Original work was done by Dmitri Epshtein and Thomas Petazzoni. I
just adapted it to take care of Ben's comments.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Dmitri Epshtein <dima@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast and broadcast packets may have RTCF_LOCAL set in rt_flags
and therefore will be sent out bypassing encapsulation. This breaks
delivery of packets sent to the vxlan multicast group.
Disabling encapsulation bypass for multicasts and broadcasts fixes the
issue.
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Tested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Tested-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently "bridge fdb show dev vxlan0" lists loopback address as
"1.0.0.127". Using htonl(INADDR_LOOPBACK) rather than passing it
directly to vxlan_snoop fixes the problem.
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary macros that duplicate generic
kernel functions.
When a struct net_device is available:
Convert printks to netdev_<level>
Convert netif_msg_<foo> and ugeth_<level> to netif_<level>
Add pr_fmt. Standardize on newlines at end of format.
Remove some duplicated newlines from output.
Coalesce formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging style.
Convert pr_<level> to netdev_<level> when a struct net_device is
available. Add pr_fmt and neaten other formats too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging message style.
Convert the printks where a struct net_device is available to
netdev_<level>. Convert the other printks to pr_<level> and
add pr_fmt where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when booting a mx6 device we get the following on boot:
registered PHC device on eth%d
Fix it by printing the network device name only after it gets registered, so
that the following can be read now:
fec 2188000.ethernet eth0: registered PHC device 0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvmdio driver uses the phylib API, so it should select the PHYLIB
symbol, otherwise, a build with mvmdio (but without mvneta) fails to
build with undefined symbols such as mdiobus_unregister, mdiobus_free,
etc.
The mvneta driver does not use the phylib API directly, so it does not
need to select PHYLIB. It already selects the mvmdio driver anyway.
Historically, this problem is due to the fact that the PHY handling
was originally part of mvneta, and was later moved to a separate
driver, without updating the Kconfig select statements
accordingly. And since there was no functional reason to use mvmdio
without mvneta, this case was not tested.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale Vybrid platform implentments MAC-ENET core
providing compatibility with half- or full-duplex
10/100 Mbit/s Ethernet LANs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not implement this in b43, but use bcma_pmu_spuravoid_pllupdate().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pretty much everywhere that uses a trace definition
header that's not in include/trace/events/ uses the
make system for the include path rather than putting
it into the sources, so do that in ath5k as well.
This came up during backporting work (where this is
required), but since all other drivers do it this
way upstream it seemed applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came up during my backporting work but it seems
perfectly appropriate for the kernel as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With recent support for GRO, there is no need to keep both LRO and
GRO. This patch therefore removes the deprecated inet_lro support
from mv643xx_eth. This is work is based on an experimental patch
provided by Eric Dumazet and Willy Tarreau.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Based-on-patch-by: Eric Dumazet <eric.dumazet@gmail.com>
Based-on-patch-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes following warning:
drivers/net/vxlan.c:406:6: warning: symbol 'vxlan_fdb_free' was not declared. Should it be static?
drivers/net/vxlan.c:1111:37: warning: Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
[ Bug added in linux-3.8 , commit 4008e97f86
("tuntap: fix ambigious multiqueue API") ]
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use skb_partial_csum_set() to simplify the codes.
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver should use return value of __vlan_put_tag with appropriate
NULL-check instead of old skb pointer.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value can be obtained from the struct brcmf_if object pointer
and it is used only twice.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the function by brcmf_fws_mac_desc_closed(). The new function
is used in the transmit path and in the dequeue worker.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing the ifidx and lookup the ifp inside the
function brcmf_fws_find_mac_desc() simply pass the ifp as
parameter.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_fws_find_mac_desc() determines the descriptor
associated with a sk_buff for firmware-signalling. It needs the
interface type to do that. For this a helper function is added in
wl_cfg80211.c.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for platform specific data for SDIO
fullmac devices. Currently OOB interrupts are configured by Kconfig
BRCMFMAC_SDIO_OOB but that is now determined dynamically by checking
availibility of platform data.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added sdio device id to list of supported devices. 43143 is a new
802.11n single stream device.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4335 is an a/b/g/n/ac WiFi chip that supports up to 80MHz channel. This patch
adds support for this chip through SDIO interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set device in a manner that SDIO I/O card reset
will lead to WLAN backplane and PMU state reset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer WiFi chip use ARM CR4 core to achieve higher performance. Add necessary
code for host driver in order to support CR4 core.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adopting the new d11 interface for 11ac fullmac chip support.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11 core interface is upgraded with 11ac support. Add channel spec support
code to brcmutil.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enter/exit download state routine is going to diverge with new ARM core
introduced. Move corresponding code to sdio_chip.c for new ARM core support.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For fullmac chips host driver can access to dongle RAM through SDIO function 1.
Introduce brcmf_sdio_ramrw and place it at bcmsdh.c with other interface
functions.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save & restore is an advanced power saving feature,
supported only on selected devices.
SR operation is almost completely transparent to the driver.
Support for it is hardware and firmware dependent.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware parsing of Control Wrapper Frames needs to be disabled, as
it has been causing spurious decryption error reports. The initvals for
other chips have been updated to disable it, but AR9580 was left out for
some reason.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To get correct endianes on little endian cpus (like arm) while reading device
tree properties, this patch replaces of_get_property() with
of_property_read_u32(). While there use of_property_read_bool() for the
handling of the boolean "nxp,no-comparator-bypass" property.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit:
1c6c695 genirq: Reject bogus threaded irq requests
threaded irqs must provide a primary handler or set the IRQF_ONESHOT flag.
Since the mcp251x driver doesn't make use of a primary handler set the
IRQF_ONESHOT flag.
Cc: linux-stable <stable@vger.kernel.org> # >= v3.5
Reported-by: Mylene Josserand <Mylene.Josserand@navocap.com>
Tested-by: Mylene Josserand <Mylene.Josserand@navocap.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Convert use of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
This was found with coccinelle.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support to mv643xx_eth by making it invoke
napi_gro_receive instead of netif_receive_skb.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan_features was zero which prevents vlan GSO packets to be transmitted to
userspace. This is suboptimal so enable this by initialize vlan_features for
tuntap.
Netperf shows better performance of guest receiving since vlan TSO works for
tuntap:
before:
netperf -H 192.168.5.4
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.4 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.01 2786.67
after:
netperf -H 192.168.5.4
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.4 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 8085.49
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's nothing that prevent passing the device features of virtio_net to its
vlan device. So this patch simply passes those to vlan device to benefit from
advanced features.
Netperf shows better sending performance for vlan device since TSO can work on
vlan now.
before:
netperf -H 192.168.5.2
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.2 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 4162.35
after:
netperf -H 192.168.5.2
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.2 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 9365.42
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves shared private data kzalloc to managed devm_kzalloc and
cleans now unneccessary kfree and error handling.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an optional shared block clock to avoid lockups on
clock gated controllers. Besides the new clock, clock handling for
existing clocks is cleaned up and moved to devm_clk_get. Device
tree binding documentation is updated for the new clocks property.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting MTU in SRIOV mode add ETH, VLAN and FCS header length
to the maximum MTU obtained from QUERY_DEV_CAP.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different steering modes are global to the device, with DMFS
being introduced after SRIOV was merged. Hence, SRIOV guests running
legacy / older Linux kernels or non-Linux drivers may provide
B0 steering directives when the hypervisor is using DMFS and fail.
Under B0 only L2 steering rules are allowed, hence B0 is a subset of DMFS.
Use this fact to enable such legacy guests to run by modifying the SRIOV
B0 steering wrapper to translate guest B0 directives to DMFS ones when
the device uses DMFS. The translated B0 rule has to be kept in the
resource tracker as a B0 object to allow for lookup in case of detach.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DesignWare MAC is synthesised with MMC RX IPC Counter, an unmanaged
and unacknowledged interrupt is generated after some time of operation.
This patch masks the undesired interrupts.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While enslaving a new device and after IFF_BONDING flag is set, in case
of failure it is not stripped from the device's priv_flags while
cleaning up, which could lead to other problems.
Cleaning at err_close because the flag is set after dev_open().
v2: no change
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 471cb5a33d ("bonding: remove
usage of dev->master") a bug was introduced which causes a NULL pointer
dereference. If a bond device is in mode 6 (ALB) and a slave is added
it will dereference a NULL pointer in bond_slave_netdev_event().
This is because in bond_enslave we have bond_alb_init_slave() which
changes the MAC address of the slave and causes a NETDEV_CHANGEADDR.
Then we have in bond_slave_netdev_event():
struct slave *slave = bond_slave_get_rtnl(slave_dev);
struct bonding *bond = slave->bond;
bond_slave_get_rtnl() dereferences slave_dev->rx_handler_data which at
that time is NULL since netdev_rx_handler_register() is called later.
This is fixed by checking if slave is NULL before dereferencing it.
v2: Comment style changed.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link change is detected via the interrupt pipe, and bulk
pipes are responsible for transfering packets, so it is reasonable
to stop bulk transfer after link is reported as off.
Two adavantages may be obtained with stopping bulk transfer
after link becomes off:
- USB bus bandwidth is saved(USB bus is shared bus except for
USB3.0), for example, lots of 'IN' token packets and 'NYET'
handshake packets is transfered on 2.0 bus.
- probabaly power might be saved for usb host controller since
cancelling bulk transfer may disable the asynchronous schedule of
host controller.
With this patch, when link becomes off, about ~10% performance
boost can be found on bulk transfer of anther usb device which
is attached to same bus with the usbnet device, see below
test on next-20130410:
- read from usb mass storage(Sandisk Extreme USB 3.0) on pandaboard
with below command after unplugging ethernet cable:
dd if=/dev/sda iflag=direct of=/dev/null bs=1M count=800
- without the patch
1, 838860800 bytes (839 MB) copied, 36.2216 s, 23.2 MB/s
2, 838860800 bytes (839 MB) copied, 35.8368 s, 23.4 MB/s
3, 838860800 bytes (839 MB) copied, 35.823 s, 23.4 MB/s
4, 838860800 bytes (839 MB) copied, 35.937 s, 23.3 MB/s
5, 838860800 bytes (839 MB) copied, 35.7365 s, 23.5 MB/s
average: 23.6MB/s
- with the patch
1, 838860800 bytes (839 MB) copied, 32.3817 s, 25.9 MB/s
2, 838860800 bytes (839 MB) copied, 31.7389 s, 26.4 MB/s
3, 838860800 bytes (839 MB) copied, 32.438 s, 25.9 MB/s
4, 838860800 bytes (839 MB) copied, 32.5492 s, 25.8 MB/s
5, 838860800 bytes (839 MB) copied, 31.6178 s, 26.5 MB/s
average: 26.1MB/s
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the introduced usbnet_link_change to handle link change.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the introduced usbnet_link_change() to handle
link change.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't implement link_reset() callback, so it needn't
to send link reset event.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the API of usbnet_link_change, so that
usbnet can handle link change centrally, which may help to
implement killing traffic URBs for saving USB bus bandwidth
and host controller power.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cnic module is responsible for initializing various bnx2x structs
via callbacks provided by the bnx2x module.
One such struct is the queue object for the FCoE queue.
If a device is working in AFEX mode and its configuration allows FCoE yet
the cnic module is not loaded, it's very likely a null pointer dereference
will occur, as the bnx2x will erroneously access the FCoE's queue object.
Prevent said access until cnic properly registers itself.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly register our mac80211_hwsim_driver, attach it to the platform bus.
Bind newly created hwsim devices to that driver, so that our wlan devices get
a proper "driver" sysfs attribute.
This makes mac80211_hwsim interfaces work with NetworkManager.
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
[fix an old and a new message to not be line-broken,
also fix the driver_register error path]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is better to use kstrto* instead of simple_strtoul. In this case it
applies a bit stricter rules for input as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In routine _rtl8188e_read_power_value_fromprom(), there are loops initializing
index_cck_base and index_bw40_base from the PROM. As the result of a typo, the
second loop is ended one element too soon.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inside one FIFO slot queue, EDMA chipsets have the same link pointer
re-read race condition as older chipsets, so the same buffer holding
logic needs to be used in order to avoid use-after-free bugs.
Unlike on older chips, it can be skipped for the end of the queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If AR_CRCErr, AR_PHYErr, AR_DecryptCRCErr or AR_MichaelErr is indicated
in the rx status word, but AR_RxFrameOK is also set, the descriptor
contents are typically invalid. This can show up as a warning about
invalid MCS rates in a frame. Even with those checks in place, a
descriptor with invalid MCS rates can still sometimes make it through to
the driver (mostly on older hardware like AR91xx).
Detect such errors in the last descriptor of a frame and discard the
whole frame if present.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the comment in ath_get_next_rx_buf indicates, if a descriptor with
the done bit set follows one with the done bit cleared, both descriptors
should be discarded, however the driver is not doing that yet.
To fix this, use the rs->rs_more flag as an indicator that the following
frame should be discarded. This also helps with the split buffer case:
if the first part of the frame is discarded, the following parts need to
be discarded as well, since they contain no valid header or usable data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of leaving the buffer without skb and breaking out of the loop
(which could leak the rx buffer), use the common error path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Banks 0-3,7 are neither modified at run time, nor SREV dependent.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All users are converted to use the rt2x00mmio_*
functions so remove the now unused defines.
The patch contain no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions in the rt2x00mmio module has been
moved from the rt2x00pci module. Each function
uses the rt2x00pci prefix which is a bit confusing.
Use the r2x000mmio prefix for each function to make
it consistent with the module name.
The renamed functions are used by several modules,
and updating the names in all of them would result
in a big patch. In order to keep the patch simple,
add compatibility defines for the old function
names. This allows to update the names in each
module separately. After each module is updated,
the defines can be removed.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And make use of it in b43. This fixes a regression introduced with
49d55cef5b
b43: N-PHY: implement spurious tone avoidance
This commit made BCM4322 use only MCS 0 on channel 13, which of course
resulted in performance drop (down to 0.7Mb/s).
Reported-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using bool can make code more readable.
Convert uses and tests of int to bool.
This also makes a comparison of tg3->link_up
(itself bool) a bool comparison instead of int.
Reorder stack variable declarations to make
bool fit declaration holes where appropriate.
$ size drivers/net/ethernet/broadcom/tg3.o*
text data bss dec hex filename
169958 27249 58896 256103 3e867 drivers/net/ethernet/broadcom/tg3.o.new
169968 27249 58896 256113 3e871 drivers/net/ethernet/broadcom/tg3.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When LFA is enabled, we don't reset the phy. But EEE settings changes
don't take effect until the phy is reset. Add a phy reset when we detect
a changed EEE setting.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally on driver load, we set the default settings for speed and flow
control. However, if the default setting is not compatible with the current link
state, we would autonegotiate and cause a link flap. To avoid this, we
pull the current advertised settings into the config.
A second scenario is if a user changes the speed/duplex/fc settings when
the interface is down. In this case we must not pull the settings from
the phy and overwrite user settings. We avoid that by checking the
USER_CONFIGURED flag.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch and the following two patches add support for link flap avoidance
by maintaining the link on power down. This feature is required for
management capable devices to have the management connection
uninterrupted on driver reload, reboot and interface up/down.
The other pros of this feature are
- It speeds up boot up time by several seconds as DHCP addresses can be
acquired faster.
- It avoids lengthy Spanning Tree delay.
On powerup the hardware brings up the phy with default settings. If the
link is not up, the management software configures the phy to gigabit
and starts autonegotiate. Subsequently, as long as the link is up, the
driver and management refrain from resetting and/or changing any
configuration that the link depends on.
The LNK_FLAP_AVOID setting is an NVRAM user configurable bit and is
disabled by default. If this setting is enabled, we skip powering down
the phy and resetting it.
A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
support for gigabit link speed when device is on auxiliary power.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor for use in the next patch that adds sgmii phy support.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user executes certain ethtool commands such as -s, -A, -G, -L,
-r a phy reset or autonegotiate is performed which results in management
traffic being interrupted.
Add a warning in these cases.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unnecessarily resets the phy when we use ethtool to
change the ring parameters or flow control settings. Remove the phy
reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting. If flow control does not match, a relink is not necessary as
flow control is not a PHY setting. Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving unhandled notifications is most certainly not an error
and should not be logged as one. Knowing that the device sends
notifications we don't handle is useful for developers, but there
is very little a user can do about this. The message is therefore
just annoying noise to most users with devices sending unhandled
notifications like e.g. USB_CDC_NOTIFY_RESPONSE_AVAILABLE
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to prefetch, in the stmmac_rx, the whole
dma_erx descriptor in case of using the extended descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recently many new supports have been added in the stmmac driver w/o taking care
about where each new field had to be placed inside the private structure for
guaranteeing the best cache usage.
This is what I wanted in the beginning, so this patch reorganizes all the fields
in order to keep adjacent fields for cache effect.
I have also tried to optimize them by using pahole.
V2: do not abuse with ____cacheline_aligned_in_smp and keep fields that
potentially could stay in the same cache-line for better usage in SMP systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch reviews/improves and adds some fixes in the code doc.
Also kernel-doc passes w/o any warnings.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the pcs mode support for SGMII. Even though
SGMII does auto-negotiation with phy, it needs stmmac_init_phy and
stmmac_mdio_register function for initializing phy.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell mdio driver uses internal registers that can be clock gated on
some SoCs. This patch just adds optional clock handling, to allow to pass
and enable the corresponding clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the bonding module is unloading, it is considered that after
rtnl_link_unregister all bond devices are destroyed but since no
synchronization mechanism exists, a new bond device can be created
via bonding_masters before unregister_pernet_subsys which would
lead to multiple problems (e.g. NULL pointer dereference, wrong RIP,
list corruption).
This patch fixes the issue by removing any bond devices left in the
netns after bonding_masters is removed from sysfs.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4de79c737b.
This patch introduces a new bug which causes access to freed memory.
In bond_uninit: list_del(&bond->bond_list);
bond_list is linked in bond_net's dev_list which is freed by
unregister_pernet_subsys.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In brcmf_rx_frames() the call to brcmf_fweh_process_skb() could
change the ifidx using information in the event data. This is
only different to the BDC ifidx for IF ADD event. However, the
creation of the new interface is deferred to event worker so
it does not exist. After brcmf_fweh_process_skb() it is only
used to set statistics.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_p2p_notify_action_frame_rx() the wireless_dev
is needed to pass the action frame to cfg80211. The wireless_dev
is held in brcmf_cfg80211_vif object. Use that instead of the
ieee80211_ptr in net_device as P2P_DEVICE interface does not have
a net_device associated with it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The probe requests received on P2P_DEVICE interface were not sent
to wpa_supplicant, which makes the device not discoverable by peers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware sends a IF event to notify the host driver that the
P2P_DEVICE interface has been created. Wait for the event before
returning the related wireless_dev.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current driver code creates a P2P_DEVICE through a module
parameter. This device has a dummy netdevice which is not how this
interface type is intended. This patch add proper support for the
P2P_DEVICE interface type. This requires a wpa_supplicant with such
support as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
escan functionality is also required for P2P device operations so it
is better not to rely on struct netdevice instances.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove use of struct netdevice as parameter to brcmf_set_mpc() as it
will not always be available, ie. there will be non-netdevice interfaces.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the introduction of the P2P_DEVICE interface type an instance of
struct wireless_dev does not always have a netdev assigned to it. Better
use container_of() construct to obtain internal structure and go from
there.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In fweh module the event handler was only called if the
struct brcmf_if instance had a non-null netdev associated.
This restriction is no longer valid for P2P_DEVICE type
of interface. This patch removes that restriction.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According specification the IF event has an additional field indicating
the role or type of the interface for which this event is sent.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firware shared data structure is backward compatible for fields
we are interested in.
Allow reading of shared data in case of version mismatch.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware console output can be read also when there was
no trap indication.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware can request the host driver for packets, by sending
either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive.
This patch adds handling of these primitives.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reported by Hante. Needs to be squashed in commit 187fbcec.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not locking ra_list when dequeuing packets creates race conditions.
When adding a packet 'tx_pkts_queued' is modified before setting
highest_priority_queue. If in-between the main loop starts, it will
see a packet queued (tx_pkts_queued > 0) but will not find it, since
max prio is not set yet. Depending on the scheduling, the thread
trying to add the packet could complete and restore the situation.
But this is not something to rely on.
Another race condition exists, if a new packet, exceeding current
max prio is added. If concurrently a packet is dequeued, the newly
set max prio will be overwritten with the value of the dequeued
packet. This can occur, because selecting a packet and modifying
the max prio is not atomic. The result in an infinite loop unless,
a new packet is added that has at least the priority of the hidden
packet.
Same applies to bss_prio_tbl. Forward iteration is no proper
lock-free technique and provides no protection from calls to
list_del. Although BSS are currently not added/removed dynamically,
this must not be the case in the future. Hence always hold proper
locks when accessing those lists.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using NO_PKT_PRIO_TID and tx_pkts_queued to check for an empty
state, can lead to a contradictory state, resulting in an
infinite loop. Currently queueing and dequeuing of packets is
not synchronized, and can happen concurrently. While tx_pkts_queued
is incremented when adding a packet, max prio is set to NO_PKT when
the WMM list is empty. If a packet is added right after the check
for empty, but before setting max prio to NO_PKT, that packet is
trapped and creates an infinite loop.
Because of the new packet, tx_pkts_queued is at least 1, indicating
wmm lists are not empty. Opposing that max prio is NO_PKT, which
means "skip this wmm queue, it has no packets". The infinite loop
results, because the main loop checks the wmm lists for not empty
via tx_pkts_queued, but for dequeing it uses max_prio to see if it
can skip current list. This will never end, unless a new packet is
added which will restore max prio to the level of the trapped packet.
The solution here is to rely on tx_pkts_queued solely for checking
wmm queue to be empty, and drop the NO_PKT define. It does not
address the locking issue.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ra_list_spinlock is used to protect struct mwifiex_wmm_desc and
embedded structures such as ra_list. tid_tbl_lock while more fine
grained, is not used but in one function. That function is not
called reentrantly. To protect ra_list from concurrent modification
ra_list_spinlock must be held.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
adapter->bss_prio_tbl list has already been checked in outer loop.
The inner loop works with priv_tmp->wmm.tid_tbl_ptr list. Also the
lock taken, gives hint that this is likely a copy-paste error.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An allyesconfig build of rtl8188ee yields the following duplicate entry points:
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `.rtl92c_phy_ap_calibrate':
(.text+0x21d14): multiple definition of `.rtl92c_phy_ap_calibrate'
drivers/net/wireless/rtlwifi/rtl8192c/built-in.o:(.text+0xb1e8): first defined here
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `rtl_hal_pwrseqcmdparsing':
(.opd+0xed0): multiple definition of `rtl_hal_pwrseqcmdparsing'
One of the routines is not used and can be deleted, the other is renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building rtl8188ee yields warnings such as the following:
x86_64-linux-gcc: warning: drivers/net/wireless/rtlwifi: linker input file unused because linking not done
The only potential cause is an extraneous space in the make file.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are the remaining knobs in ath9k to support DFS:
* mark AR9280 and AR9580 as DFS tested
* synchronize DFS regulatory domain to reg notifyer
* set required RX filter flags for radar detection
* process radar PHY errors at DFS detector
* notify DFS master on radar detection
DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps testing DFS without radar generating
equipment and is required for certification.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should make the warning messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cmd_pending is increased in mwifiex_wait_queue_complete() and
decreased in mwifiex_complete_cmd() currently.
If there are two or more commands in the cmd_pending_q the main
worker thread will pick up next command from cmd_pending_q
automatically after finishing current command. As a result
mwifiex_wait_queue_complete() will not be called because
the command is alreay completed. This leads to a negative
number in cmd_pending count.
Fix it by increasing cmd_pending when a cmd is queued into
cmd_pending_q and decreasing when that cmd is recycled. For scan
commands we don't perform inc/dec operations until it's moved
from scan_pending_q to cmd_pending_q. This covers both
synchronous and asynchronous commands.
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware is requested from user-space. To assure the request
is handled it is recommended to do the request upon IFF_UP. For
a mac80211 driver the .start() callback can be considered the
equivalent.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For v3.9 kernel the P2P functionality was merged, but it does
not fully support the P2P_DEVICE interface type. This patch
removes advertising that support.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the firmware has been open sourced, the minor version has been
bumped to 1.4 and the API/ABI will stay compatible across further 1.x
releases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that the reason why the dev features were ignored was because
they were enabled after registeration.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the VM_PKT_COMP message can arrive later than RNDIS completion
message, which will free the packet memory. This may cause panic due to access
to freed memory in netvsc_send_completion().
This patch fixes this problem by removing rndis_filter_send_request_completion()
from the code path. The function was a no-op.
Reported-by: Long Li <longli@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The warning about local_bh_enable inside IRQ happens when disconnecting a
virtual NIC.
The reason for the warning is -- netif_tx_disable() is called when the NIC
is disconnected. And it's called within irq context. netif_tx_disable() calls
local_bh_enable() which displays warning if in irq.
The fix is to remove the unnecessary netif_tx_disable & wake_queue() in the
netvsc_linkstatus_callback().
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet. Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.
Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
of these fixes are needed to support omap5 es2 version that includes
PM features while the earlier version es1 did not.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mjWl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren <tony@atomide.com>:
Non critical omap fixes for v3.10 merge window. A big chunk
of these fixes are needed to support omap5 es2 version that includes
PM features while the earlier version es1 did not.
* tag 'omap-for-v3.10/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: OMAP: dpll: enable bypass clock only when attempting dpll bypass
ARM: OMAP2+: powerdomain: avoid testing whether an unsigned char is less than 0
ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
ARM: OMAP2+: am335x: Change the wdt1 func clk src to per_32k clk
ARM: OMAP2+: AM33xx: hwmod: Add missing sysc definition to wdt1 entry
Contains an update to 3.9-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a feature is not supported by firmware no need to print an error message.
This surpresses the following harmless message on boot up and ethtool query.
enic: Error 1 devcmd 36
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.
There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now we didn't handle properly the FLUSH ampdu action
coming from mac80211. This could result in SCD queue leak:
mac80211 would STOP_FLUSH an AMPDU Tx session and remove
the station. If we had still packets on the ring, we
wouldn't deallocate the SCD queue and wait for it to be
empty.
The indication of the queue being empty comes from the Tx
response flow which relies on the tid_data structure. The
problem is that this structure has been cleared when the
station has been removed.
In order to solve this issue, block in the STOP_FLUSH
ampdu_action until the SCD queue is flushed, and only then,
let mac80211 move forward to remove the station.
iwlagn_txfifo_flush had to be enhanced to allow this.
The bug fixed here caused the "txq_id mismatch: 12 0" print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 332235427a
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"
I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.
Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If request_module() failed then we didn't have the correct
opmode module that the driver needs to function, so print
a warning in this case to make it more obvious what could
be wrong. This still won't catch the case where the module
simply doesn't exist because it wasn't compiled though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers can now advertise VHT support even if they don't use channel
contexts.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.
Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bypasses vxlan encapsulation if the destination vxlan
endpoint is a local device.
Changes since v1: added missing check for vxlan_find_vni() failure
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When our getdcbx entry is called, DCB_CAP_DCBX_HOST should be advertized too.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.
PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new settings and correct the wrong settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a race condition if we try to rmmod bonding and simultaneously add
a bond master through sysfs. In bonding_exit() we first remove the devices
(through rtnl_link_unregister() ) and only after that we remove the sysfs.
If we manage to add a device through sysfs after that the devices were
removed - we'll end up with that device/sysfs structure and with the module
unloaded.
Fix this by first removing the sysfs and only after that calling
rtnl_link_unregister().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limit of 0x3c00 is taken from the windows driver.
Suggested-by: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Here are some more fixes intended for the 3.9 stream...
Regarding the mac80211 bits, Johannes says:
"I had changed the idle handling to simplify it, but broken the
sequencing of commands, at least for ath9k-htc, one patch restores the
sequence. The other patch fixes a crash Jouni found while stress-testing
the remain-on-channel code, when an item is deleted the work struct can
run twice and crash the second time."
As for the iwlwifi bits, Johannes says:
"The only fix here is to the passive-no-RX firmware regulatory
enforcement driver support code to not drop auth frames in quick
succession, leading to not being able to connect to APs on passive
channels in certain circumstances."
Don't forget the NFC bits, about which Samuel says:
"This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
On top of that, Stone Piao provides an mwifiex fix to avoid accessing
beyond the end of a buffer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It actually handles a BT coex notification, so rename it
to be more self explained.
Also, this function can always look at mvm->last_bt_notif
provided that the latter is updated on time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
some new thinkpad laptops use intel chip with new pci id need be added
lspci -vnn output:
Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
[8086:088f] (rev 24)
Subsystem: Intel Corporation Device [8086:5260]
Signed-off-by: Shuduo Sang <sangshuduo@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iterators don't need to know what bt_kill_msk means.
All they need to know is if reduced Tx power is enabled
on an interface or not. So change the member of the
iterator to be a bool.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware API changed to differentiate between event and
fragment start/end. Change the time-event handling accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many platforms have issues processing a wakeup signal
while they're still suspending, and will ignore it.
Since our device thinks it woke the platform, and the
platform ignored the signal, it will sleep without
WoWLAN being enabled as the device disables WoWLAN
when having woken the platform.
Resolve this by making the device wait for 10 seconds
after getting the suspend signal before waking up the
platform.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function just wraps an existing one, remove it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The requirement for TX/RX active to powersave transition time for
the Balanced Power Save (BPS) scheme changed. Change the driver
accordingly and set transition time to 100 msec.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Encapsulate the power table command logging in a separate
function to print the same information in both cases.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware starts sending nulldata frames for keepalive immediately
after association, regardless of power management state. The driver
thus needs to configure keep alive period unconditionally.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver distinguishes between power management and device's power
down enablement. Power management enablement depends both on driver's
module power parameters and mac80211 decision. The device's power down
depends only on driver's module power parameters. Change the driver to
always send Power Table command to enable or disable both power
management and device's power down.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Active to power save mode transition time for TX/RX in the power
table command is in microseconds, fix the units in the driver.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions are moved in preparation of later patches.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length is not according specification so better fix it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
