The current gpio code needs to know the number of
gpio irqs there are and what the bank irq number is.
To determine those values, it checks the SoC type.
It also assumes that the base address and the number
of irqs the interrupt controller uses is fixed.
To clean up the SoC checks and make it support
different base addresses and interrupt controllers,
have the SoC-specific code set those values in
the soc_info structure and have the gpio code
reference them there.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch seems to get me much more reliable performance using the
GPIO banked interrupts on dm355 for the dm9000 driver.
Changes include:
- init GPIO handling along with normal GPIO init
- mask the level-sensitive bank IRQ during handling
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix two IRQ triggering bugs affecting GPIO IRQs:
- Make sure enabling with IRQ_TYPE_NONE ("default, unspecified")
isn't a NOP ... default to both edges, at least one must work.
- As noted by Kevin Hilman, setting the irq trigger type for a
banked gpio interrupt shouldn't enable irqs that are disabled.
Since GPIO IRQs haven't been used much yet, it's not clear these
bugs could have affected anything. The few current users don't
seem to have been obviously suffering from these issues.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:
- Only handle the number of GPIOs the chip actually has. So
for example on dm6467, GPIO-42 is the last GPIO, and trying
to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.
- Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
previously, only the first five were enabled, so GPIO-80
and above (on dm355) wouldn't trigger IRQs.
- Use the right IRQ for each GPIO bank. The wrong values were
used for dm355 chips, so GPIO IRQs got routed incorrectly.
- Handle up to four pairs of 16-bit GPIO banks ... previously
only three were handled, so accessing GPIO-96 and up (e.g. on
dm355) would oops.
- Update several comments that were dm6446-specific.
Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.
One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs. Some
bitmap logic could fix that if needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch DaVinci SOC gpios over to using the new GPIO library, so it can
access GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Support GPIO driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarino@ru.mvista.com>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
