This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Fix hardware access for ppc architecture.
sis190: new PHY support
atl1: save mac address on remove
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported to work on the WinFast 761GXK8MB-RS motherboard.
Plain 10/100 Mbps.
Signed-off-by: Paul Gibbons <paul@pkami.e7even.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some atl1 boards get their MAC address written directly to the register
by the BIOS during POST, rather than storing it in EEPROM that's
accessible to the driver. If the MAC register on one of these boards
is changed and then the module is unloaded, the permanent MAC address
will be forgotten until the box is rebooted. We should save the
permanent address during removal if we've been messing with it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.
The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e4d.
This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The tx timeout routine was waking the tx queue conditionally. However,
it must call it unconditionally since the dev_watchdog has halted the tx
queue before calling the timeout function.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nic poll routine was missing the call to the optimized irq routine.
This patch adds the missing call for the optimized path.
See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rx checksum bits. Turn on TCP processing for rx checksum.
Fixed max frame length register write. It wasn't getting set
in multi-port system. Set rx buffer queue length properly
for jumbo frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the rx queue pointer when exiting NAPI poll rather than
at the end of each iteration. Remove unnecessary PCI flushes
that occurred after every write. Now write all regs and
flush once.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was removed in a previous patch to increase performance, but
caused a transmit error for the 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original vendor driver contained a private ether_crc_le() function
that produced an inverted crc. When we changed to the kernel version of
ether_crc_le(), we neglected to undo the inversion. Let's do it now.
Discovered by and patch proffered by Jose Alberto Reguero.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correctly detect when TSO should be used on transmit by looking at the
skb->gso_size rather than seeing if the frame was larger than our MTU.
The old method causes problems when a host with a large (jumbo) MTU is
sending to a host with a small (standard) MTU.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent changes in the specs that were introduced in commit
740ac4fb08 were incorrect and resulted in machine check
errors on the PPC architecture for G PHY's with a revision number equal to 1. The
two offending changes are reverted.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a duplicated leftshift in bcm43xx_radio_set_tx_iq. data_high values are
already leftshifted. Thanks to Michael Buesch for spotting this.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where the PHY version and revision were interchanged.
These are changed in the specifications on 2/13/07 and now use "analog" instead
instead of "version" to help reduce confusion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements set_mac_address for the sungem driver. This
allows changing the mac address of the interface, even when the
interface is up.
Signed-off-by: Ruben Vandeginste <snowbender@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On most tg3 chips, the memory enable bit in the PCI command register
gets cleared during chip reset and must be restored before accessing
PCI registers using memory cycles. The chip does not generate
interrupt during chip reset, but the irq handler can still be called
because of irq sharing or irqpoll. Reading a register in the irq
handler can cause a master abort in this scenario and may result in a
crash on some architectures.
Use the TG3_FLAG_CHIP_RESETTING flag to tell the irq handler to exit
without touching any registers. The checking of the flag is in the
"slow" path of the irq handler and will not affect normal performance.
The msi handler is not shared and therefore does not require checking
the flag.
Thanks to Bernhard Walle <bwalle@suse.de> for reporting the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag to support multiple PCIX split completions was never used
because of hardware bugs. This will make room for a new flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arwin Vosselman pointed out:
> The ewrk3-driver doesn't function with 2.6.16-kernels (used 2.6.16.41 for
> my tests). Cards will never be detected due to this bug.
>
> drivers/net/ewrks3.c:
> Line 417 reads:
>
> if (nicsr == (CSR_TXD | CSR_RXD))
>
> that should be:
>
> if (nicsr != (CSR_TXD | CSR_RXD))
>
> Comparison with the same line in v2.4 shows why:
>
> 2.4:
> if (nicsr == (CSR_TXD | CSR_RXD)){
>
> blah, blah
> ==========
> 2.6:
> if (nicsr == (CSR_TXD | CSR_RXD))
> return -ENXIO;
>
> blah, blah
> ==========
>
> blah,blah will not, but should, be executed in 2.6 with a card being present.
>
> The fix mentioned above solves this bug.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix management of allocated physical pages when the architecture
page size is not 4kB since the firmware cannot cross 4K boundary.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SAA9730 driver doesn't quite grok what the difference between an ioport
and memory mapped I/O is. It just happened to work on the one Linux
system the SAA9730 happens to spend it's misserable existence on.
drivers/net/saa9730.c: In function 'evm_saa9730_enable_lan_int':
drivers/net/saa9730.c:68: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:70: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:72: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_disable_lan_int':
drivers/net/saa9730.c:78: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:80: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_clear_lan_int':
drivers/net/saa9730.c:85: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_block_lan_int':
drivers/net/saa9730.c:91: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_unblock_lan_int':
drivers/net/saa9730.c:97: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'show_saa9730_regs':
drivers/net/saa9730.c:150: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_allocate_buffers':
drivers/net/saa9730.c:292: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:295: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:302: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:305: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:312: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_cam_load':
drivers/net/saa9730.c:329: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:332: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_mii_init':
drivers/net/saa9730.c:369: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:395: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:403: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:410: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:432: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_control_init':
drivers/net/saa9730.c:470: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:474: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:478: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:484: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:487: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:490: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:493: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_stop':
drivers/net/saa9730.c:505: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:508: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:510: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_dma_init':
drivers/net/saa9730.c:536: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_start':
drivers/net/saa9730.c:556: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:560: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:564: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:567: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_tx':
drivers/net/saa9730.c:590: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_rx':
drivers/net/saa9730.c:664: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:729: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_write':
drivers/net/saa9730.c:848: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_set_multicast':
drivers/net/saa9730.c:943: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:949: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
Fixed by using writel instead of outl. 42 warnings less.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 18babd3854.
Michael Barkowski points out that it's wrong, and I agree. The
patch causes a problem rather than fixes one after another
patch "ucc_geth: Fix BD processing" was applied. Before that
patch, current packet should be blocked. However after the patch
current packet is ok and we only need to block next.
Reported-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Under rare conditions, the MAC might hang while generating a pause frame.
This patch fine tunes the MAC settings to avoid the issue, allows for
periodic MAC state check, and triggers a recovery if hung.
Also fix one MAC statistics counter for the rev board T3B2.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We assign the return value of register_netdev to i, but return rc later
on. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than a workqueue and a per-board mutex to control PHY,
use a tasklet and spinlock. Tasklet is lower overhead and works
just as well for this.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Wheen a port on the skge driver is not used, it should
mask off interrupts from theat port.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver will deadlock if gets a transmit timeout
because the netif_tx_lock() is already held.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With 42101001.sb firmwares, we need a 10 ms delay between firmware chunks
upload on irda-usb.
Patch from Nigel Williams <nigelw@elder-gods.net>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The airo driver leaks memory if request_irq() fails.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During testing of bcm43xx interference mitigation, two problems were
discovered:
(1) When the MANUALWLAN mode was set, routines _stack_save and _stack_restore
generated assertions that were traced to saving ILT registers with addresses
> 0xFFF. This problem was fixed by adding one bit to the field used for
the offset, and subtracting one bit from the space used for the id.
(2) In MANUALWLAN mode, the IRQ XMIT errors are generated. The cause of these
errors has not yet been located. Any suggestions on debugging this problem
would be greatly appreciated.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
