Add fcp_io_channel module attribute to control amount of parallel I/O queues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commonize SLI-3/4 Ring/Queue framework, to keep SLI-3 compatibility
Parallelize SLI-4 Q distribution - to use multiple posting/completion queues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
"rc" is always zero here, so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We recently changed the locking in this function, but this return was
missed. It needs an unlock and the IRQs need to be restored.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Without this patch, scsi_show_result prints hostbyte as invalid for statuses
that are not defined in hostbyte_table (when scsi logging is enabled).
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
I think ioremap() ends up being equivalent to ioremap_nocache
by default, but we should signal our intent that these mappings
should be non-cacheable.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the abort handler, when asked to abort a command which
is not known to the driver, SUCCESS is returned, but the
diagnostic message incorrectly indicates the abort failed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line. Symptoms look like this:
hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:
LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts. So we should use LUN reset,
not target reset.
Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a user to adjust the wait time in seconds after I/O timeout before
resetting the adapter.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a user to adjust the queue depth of the adapter when throttled due
to I/O timeout.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reduce the amount of time the host lock is held in the interrupt handler
for improved performance.
[jejb: fix up checkpatch noise]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reduce the amount of time the host lock is held in queuecommand
for improved performance.
[jejb: fix up checkpatch noise]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When device discovery is disabled during driver load time using module
parameter "disable_discovery=1" and when diag reset is issued then from logs,
it is observed that the devices get added, removed and then added with new
target ids.
So, in order to limit this turn-off the code which is deleting and devices
across host reset when the disable_discovery module parameter is turned on.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch provides a command line option to disable "Port enable" during
the driver load.
The objective of this command line option is to load the driver and do
all the necessary initialization excluding port enable(i.e. delay
device discovery)
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changeset in MPI 2.0 Rev V(2.0.14) specification
1) Bumped MPI2_HEADER_VERSION_UNIT.
2) Added a product specific range to event values.
3) Added clarification to Direct-Attached SAS PHY Power condition.
4) Updated timing requirements for performing Hard Reset.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When specifying the command line option "max_sectors" less than 64, then
warning message should provide correct upper boundary value 32767 instead of
8192.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A new sysfs shost attribute called "BMR_status" is implemented to
report Backup Rail Monitor status.
This attribute is located in the path
/sys/class/scsi_host/host#/BMR_status
when reading this adapter attribute, then driver will output the state
of GPIO[24]. It returns "0" if BMR is healthy and it returns "1" for failure.
if it returns an empty string then it means that there was an error while
obtaining the BMR status. Then check dmesg for what error has occured.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The Copyright String in all the drivers sources were changed to 2012
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas and ipr pass flags to ata_host_init that are meant for the port.
ata_host flags:
ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host only */
ATA_HOST_STARTED = (1 << 1), /* Host started */
ATA_HOST_PARALLEL_SCAN = (1 << 2), /* Ports on this host can be scanned in parallel */
ATA_HOST_IGNORE_ATA = (1 << 3), /* Ignore ATA devices on this host. */
flags passed by libsas:
ATA_FLAG_SATA = (1 << 1),
ATA_FLAG_PIO_DMA = (1 << 7), /* PIO cmds via DMA */
ATA_FLAG_NCQ = (1 << 10), /* host supports NCQ */
The only one that aliases is ATA_HOST_STARTED which is a 'don't care' in
the libsas and ipr cases since ata_hosts from these sources are not
registered with libata.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Brian King <brking@us.ibm.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Provide a "simple-dev-pm-ops" implementation that shuts down the domain
and the device on suspend, and resumes the device and the domain on
resume. All of the mechanics of restoring domain connectivity are
handled by libsas once isci has notified libsas that all links should be
back up. libsas is in charge of handling links that did not resume, or
resumed out of order.
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas power management routines to suspend and recover the sas domain
based on a model where the lldd is allowed and expected to be
"forgetful".
sas_suspend_ha - disable event processing allowing the lldd to take down
links without concern for causing hotplug events.
Regardless of whether the lldd actually posts link down
messages libsas notifies the lldd that all
domain_devices are gone.
sas_prep_resume_ha - on the way back up before the lldd starts link
training clean out any spurious events that were
generated on the way down, and re-enable event
processing
sas_resume_ha - after the lldd has started and decided that all phys
have posted link-up events this routine is called to let
libsas start it's own timeout of any phys that did not
resume. After the timeout an lldd can cancel the
phy teardown by posting a link-up event.
Storage for ex_change_count (u16) and phy_change_count (u8) are changed
to int so they can be set to -1 to indicate 'invalidated'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull core block IO bits from Jens Axboe:
"The most complicated part if this is the request allocation rework by
Tejun, which has been queued up for a long time and has been in
for-next ditto as well.
There are a few commits from yesterday and today, mostly trivial and
obvious fixes. So I'm pretty confident that it is sound. It's also
smaller than usual."
* 'for-3.6/core' of git://git.kernel.dk/linux-block:
block: remove dead func declaration
block: add partition resize function to blkpg ioctl
block: uninitialized ioc->nr_tasks triggers WARN_ON
block: do not artificially constrain max_sectors for stacking drivers
blkcg: implement per-blkg request allocation
block: prepare for multiple request_lists
block: add q->nr_rqs[] and move q->rq.elvpriv to q->nr_rqs_elvpriv
blkcg: inline bio_blkcg() and friends
block: allocate io_context upfront
block: refactor get_request[_wait]()
block: drop custom queue draining used by scsi_transport_{iscsi|fc}
mempool: add @gfp_mask to mempool_create_node()
blkcg: make root blkcg allocation use %GFP_KERNEL
blkcg: __blkg_lookup_create() doesn't need radix preload
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Pull networking changes from David S Miller:
1) Remove the ipv4 routing cache. Now lookups go directly into the FIB
trie and use prebuilt routes cached there.
No more garbage collection, no more rDOS attacks on the routing
cache. Instead we now get predictable and consistent performance,
no matter what the pattern of traffic we service.
This has been almost 2 years in the making. Special thanks to
Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
have helped along the way.
I'm sure that with a change of this magnitude there will be some
kind of fallout, but such things ought the be simple to fix at this
point. Luckily I'm not European so I'll be around all of August to
fix things :-)
The major stages of this work here are each fronted by a forced
merge commit whose commit message contains a top-level description
of the motivations and implementation issues.
2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
input.
3) TCP SYN/ACK performance tweaks from Eric Dumazet.
4) Add namespace support for netfilter L4 conntrack helpers, from Gao
Feng.
5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
Yuval Mintz.
6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.
7) Support for connection tracker helpers in userspace, from Pablo
Neira Ayuso.
8) Allow userspace driven TX load balancing functions in TEAM driver,
from Jiri Pirko.
9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
embedded gotos.
10) TCP Small Queues, essentially minimize the amount of TCP data queued
up in the packet scheduler layer. Whereas the existing BQL (Byte
Queue Limits) limits the pkt_sched --> netdevice queuing levels,
this controls the TCP --> pkt_sched queueing levels.
From Eric Dumazet.
11) Reduce the number of get_page/put_page ops done on SKB fragments,
from Alexander Duyck.
12) Implement protection against blind resets in TCP (RFC 5961), from
Eric Dumazet.
13) Support the client side of TCP Fast Open, basically the ability to
send data in the SYN exchange, from Yuchung Cheng.
Basically, the sender queues up data with a sendmsg() call using
MSG_FASTOPEN, then they do the connect() which emits the queued up
fastopen data.
14) Avoid all the problems we get into in TCP when timers or PMTU events
hit a locked socket. The TCP Small Queues changes added a
tcp_release_cb() that allows us to queue work up to the
release_sock() caller, and that's what we use here too. From Eric
Dumazet.
15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
r8169: revert "add byte queue limit support".
ipv4: Change rt->rt_iif encoding.
net: Make skb->skb_iif always track skb->dev
ipv4: Prepare for change of rt->rt_iif encoding.
ipv4: Remove all RTCF_DIRECTSRC handliing.
ipv4: Really ignore ICMP address requests/replies.
decnet: Don't set RTCF_DIRECTSRC.
net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
ipv4: Remove redundant assignment
rds: set correct msg_namelen
openvswitch: potential NULL deref in sample()
tcp: dont drop MTU reduction indications
bnx2x: Add new 57840 device IDs
tcp: avoid oops in tcp_metrics and reset tcpm_stamp
niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
niu: Fix to check for dma mapping errors.
net: Fix references to out-of-scope variables in put_cmsg_compat()
net: ethernet: davinci_emac: add pm_runtime support
net: ethernet: davinci_emac: Remove unnecessary #include
...
Pull target updates from Nicholas Bellinger:
"There have been lots of work in a number of areas this past round.
The highlights include:
- Break out target_core_cdb.c emulation into SPC/SBC ops (hch)
- Add a parse_cdb method to target backend drivers (hch)
- Move sync_cache + write_same + unmap into spc_ops (hch)
- Use target_execute_cmd for WRITEs in iscsi_target + srpt (hch)
- Offload WRITE I/O backend submission in tcm_qla2xxx + tcm_fc (hch +
nab)
- Refactor core_update_device_list_for_node() into enable/disable
funcs (agrover)
- Replace the TCM processing thread with a TMR work queue (hch)
- Fix regression in transport_add_device_to_core_hba from TMR
conversion (DanC)
- Remove racy, now-redundant check of sess_tearing_down with qla2xxx
(roland)
- Add range checking, fix reading of data len + possible underflow in
UNMAP (roland)
- Allow for target_submit_cmd() returning errors + convert fabrics
(roland + nab)
- Drop bogus struct file usage for iSCSI/SCTP (viro)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (54 commits)
iscsi-target: Drop bogus struct file usage for iSCSI/SCTP
target: NULL dereference on error path
target: Allow for target_submit_cmd() returning errors
target: Check number of unmap descriptors against our limit
target: Fix possible integer underflow in UNMAP emulation
target: Fix reading of data length fields for UNMAP commands
target: Add range checking to UNMAP emulation
target: Add generation of LOGICAL BLOCK ADDRESS OUT OF RANGE
target: Make unnecessarily global se_dev_align_max_sectors() static
target: Remove se_session.sess_wait_list
qla2xxx: Remove racy, now-redundant check of sess_tearing_down
target: Check sess_tearing_down in target_get_sess_cmd()
sbp-target: Consolidate duplicated error path code in sbp_handle_command()
target: Un-export target_get_sess_cmd()
qla2xxx: Get rid of redundant qla_tgt_sess.tearing_down
target: Make core_disable_device_list_for_node use pre-refactoring lock ordering
target: refactor core_update_device_list_for_node()
target: Eliminate else using boolean logic
target: Misc retval cleanups
target: Remove hba param from core_dev_add_lun
...
This reverts commit 43a8d39d01.
Commit 43a8d39d fixed the fact that wait_for_device_probe() was unable
to flush sd probe work. Now that sd probe work is once again flushable
via wait_for_device_probe() this workaround is no longer needed.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that scsi registers its async scan work with the async subsystem,
wait_for_device_probe() is sufficient for ensuring all scanning is
complete.
[jejb: fix merge problems with eea03c20ae Make wait_for_device_probe() also do scsi_complete_async_scans()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is to change use of "0x%08x" in favour of "%p" as per ../Documentation/printk-formats.txt,
which also takes care about the following warning during compilation time:
drivers/scsi/aha152x.c: In function ‘get_command’:
drivers/scsi/aha152x.c:2987: warning: cast from pointer to integer of different size
Signed-off-by: Krzysztof Wilczynski <krzysztof.wilczynski@linux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is preparation to enable async_synchronize_full() to be used as a
replacement for scsi_complete_async_scans(), i.e. to stop leaking scsi
internal details where they are not needed.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In response to an async related regression James noted:
"My theory is that this is an init problem: The assumption in a lot of
our code is that async_synchronize_full() waits for everything ... even
the domain specific async schedules, which isn't true."
...so make this assumption true.
Each domain, including the default one, registers itself on a global domain
list when work is scheduled. Once all entries complete it exits that
list. Waiting for the list to be empty syncs all in-flight work across
all domains.
Domains can opt-out of global syncing if they are declared as exclusive
ASYNC_DOMAIN_EXCLUSIVE(). All stack-based domains have been declared
exclusive since the domain may go out of scope as soon as the last work
item completes.
Statically declared domains are mostly ok, but async_unregister_domain()
is there to close any theoretical races with pending
async_synchronize_full waiters at module removal time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Eldad Zack <eldadzack@gmail.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain. This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.
The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.
[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Remove unnecessary if NULL check in function bfa_fcs_vport_free().
- Set correct return error codes in case of memory allocation failure
in the BSG ELS/CT passthru command handler.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Series 7 Async. (performance) mode support added
- New scatter/gather list format for Series 7
- Driver converts s/g list to a firmware suitable list for best performance on
Series 7, this can be disabled with driver parameter "aac_convert_sgl" for
testing purposes
- New container read/write command structure for Series 7
- Fast response support for the SCSI pass-through path added
- Async. status response buffer changes
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is reported to work, known to work on PCMCIA and a code check shows no
problems on the other bits of the code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch changes virtio-scsi to use a new virtio_driver->scan() callback
so that scsi_scan_host() can be properly invoked once virtio_dev_probe() has
set add_status(dev, VIRTIO_CONFIG_S_DRIVER_OK) to signal active virtio-ring
operation, instead of from within virtscsi_probe().
This fixes a bug where SCSI LUN scanning for both virtio-scsi-raw and
virtio-scsi/tcm_vhost setups was happening before VIRTIO_CONFIG_S_DRIVER_OK
had been set, causing VIRTIO_SCSI_S_BAD_TARGET to occur. This fixes a bug
with virtio-scsi/tcm_vhost where LUN scan was not detecting LUNs.
Tested with virtio-scsi-raw + virtio-scsi/tcm_vhost w/ IBLOCK on 3.5-rc2 code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it. Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the UFS host driver has returned incorrect values for SUCCESS
and FAILED. Fix it to return the correct value to the upper layer.
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Otherwise it counter intuitively returns 0 if device is present.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use macro module_pci_driver and get rid of boilerplate code. No
functional changes.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch implements the hotplug support for virtio-scsi.
When there is a device attached/detached, the virtio-scsi driver will be
signaled via event virtual queue and it will add/remove the scsi device
in question automatically.
Signed-off-by: Sen Wang <senwang@linux.vnet.ibm.com>
Signed-off-by: Cong Meng <mc@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To improve performance for I/O to different targets, add a separate
scatterlist for each of them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We do not need the sglist after calling virtqueue_add_buf. Hence we
can "pipeline" the locked operations and start preparing the sglist
for the next request while we kick the virtqueue.
Together with the previous two patches, this improves performance as
follows. For a simple "if=/dev/sda of=/dev/null bs=128M iflag=direct"
(the source being a 10G disk, residing entirely in the host buffer cache),
the additional locking does not cause any penalty with only one dd
process, but 2 simultaneous I/O operations improve their times by 3%:
number of simultaneous dd
1 2
----------------------------------------
current 5.9958s 10.2640s
patched 5.9531s 9.8663s
(Times are best of 10).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Keep a separate lock for each virtqueue. While not particularly
important now, it prepares the code for when we will add support
for multiple request queues. It is also more tidy as soon as
we introduce a separate lock for the sglist.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Separate virtqueue_kick_prepare from virtqueue_notify, so that the
expensive vmexit is done without holding the lock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is exposed in the case the FCP_DATA frames somehow got lost and fc_fcp got
the FCP_RSP, in fc_fcp_recv_resp(), since xfer_len is less than the expected_len
it resets the the timer to wait to 2 more jiffies in case the data frames are
already queued locally. However, for target does not support REC, it would just
send RJT w/ ELS_RJT_UNSUP. The rec response handler thus only clears the rport
flag for not doing REC later, but does not do fcp_io_complete() on the
associated fsp.
The fix is just check status of FCP_RSP being received already, i.e. using the
FC_SRB_RCV_STATUS flag, in fc_fcp_timeout before start sending REC. We should
have waited long enough if there is truely data frames queued locally.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The FC-GS-3 sepc requires to wait for least 3 times R_A_TOV per
sec 4.6.1 "If the Requesting_CT does not receive a Response
CT_IU from the Responding_CT within three times R_A_TOV,
it shall consider this to be a protocol error."
This means added four new states with management server
could add significant delay with multiple retries
on default 12 second timeout(3 * R_A_TOV), so instead
just skip these states on very first timeout on any of
these states to not stuck with states for such longer
period.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The lport_recv(), i.e., fc_lport_recv_req() may get called w/o the sequence ptr
being set in fr_seq(), particularly in the case of vn2vn mode, this may happen
if the passive fcp provider, e.g., tcm_fc, has not been registered yet.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Noticed that we can shuffle the code around in fcoe_percpu_receive_thread a bit
and avoid taking the fcoe_rx_list lock twice per iteration. This should improve
throughput somewhat. With this change we take the lock, and check for new
frames in a single critical section. Only if the list is empty do we drop the
lock and re-acquire it after being signaled to wake up.
Change Notes:
v2) did some further cleanup on the patch by replacing the 2nd call of
spin_lock/splice_init with a goto to the top of the outer loop. This allows me
to change the inner while loop to an if conditional and remove the sencond check
of kthread_should_stop. Based on suggestion from Vasu Dev.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
strtoul returns an 'unsigned long' so there is no
reason to check if the value is less than zero.
strtoul already checks for the '-' character deep
in its bowels. It will return an error if the user
has provided a negative value and fcoe_str_to_dev_loss
will return that error to its caller.
This patch fixes the following Coverity reported warning:
CID 703581 - NO_EFFECT Unsigned compared against 0 - This
less-than-zero comparison of an unsigned value is never true. "*val < 0UL".
drivers/scsi/fcoe/fcoe_sysfs.c:105
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add exch timeout info to have debug log with exch timeout
value to match with retries, also add debug info
on exch timer cancel.
Added common fc_exch_timer_cancel() func and grouped this
along with fc_exch_timer_set() function, so that
added debug code is not repeated.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is a race in scsi_bus_resume_common when set device's runtime
state to active after pm_runtime_put_sync(dev->parent).
Parent device may have been suspended so pm_runtime_set_active(dev) will
fail with -EBUSY.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit d38bd3aef ("Add -Werror compilation flag") is causing build breakage
with random gcc incarnations. These look like gcc problems, but we shouldn't
break the build because of a bad gcc. Fix this by adding a make flag
WARNINGS_BECOME_ERRORS=1
which is the same as aic7xxx uses so ordinarily the build doesn't use -Werror
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Alex Iannicelli <alex.iannicelli@emulex.com>
Cc: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We don't use "dev" any more after 07ec747a5f ("libsas: remove
ata_port.lock management duties from lldds") and it causes a compile
warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The timer and the completion are only used for slow path tasks (smp, and
lldd tmfs), yet we incur the allocation space and cpu setup time for
every fast path task.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On the way to add a new sata_device field, noticed that libsas is
carrying port multiplier infrastructure that is explicitly disabled by
sas_discover_sata(). The aic94xx touches the unused port_no, so leave
that field in case there was some use for it.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 198439e4 [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
commit 19252de6 [SCSI] libsas: fix wide port hotplug issues
The above commits seem to have confused the return value of
sas_ex_discover_dev which is non-zero on failure and
sas_ex_join_wide_port which just indicates short circuiting discovery on
already established ports. The result is random discovery failures
depending on configuration.
Calls to sas_ex_join_wide_port are the source of the trouble as its
return value is errantly assigned to 'res'. Convert it to bool and stop
returning its result up the stack.
Cc: <stable@vger.kernel.org>
Tested-by: Dan Melnic <dan.melnic@amd.com>
Reported-by: Dan Melnic <dan.melnic@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Continue running revalidation until no more broadcast devices are
discovered. Fixes cases where re-discovery completes too early in a
domain with multiple expanders with pending re-discovery events.
Servicing BCNs can get backed up behind error recovery.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The discovery function "sas_rediscover_dev" had two bugs: 1) it did
not pay attention to the return status from the SMP task execution;
2) the stack variable used for the returned SAS address was compared
against 0 without being initialized.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
...now that the strategy handlers guarantee eh context and notify
the driver of bus reset.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sas_eh_bus_reset_handler() amounts to sas_phy_reset() without
notification of the reset to the lldd. If this is triggered from
eh-cmnd recovery there may be sas_tasks for the lldd to terminate, so
->lldd_I_T_nexus_reset is warranted.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Luben Tuikov <ltuikov@yahoo.com>
Cc: Jack Wang <jack_wang@usish.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
[jacek: modify pm8001_I_T_nexus_reset to return -ENODEV]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When recovering failed eh-cmnds let the lldd attempt an abort via
scsi_abort_eh_cmnd before escalating.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The strategy handlers may be called in places that are problematic for
libsas (i.e. sata resets outside of domain revalidation filtering /
libata link recovery), or problematic for userspace (non-blocking ioctl
to sleeping reset functions). However, these routines are also called
for eh escalations and recovery of scsi_eh_prep_cmnd(), so permit them
as long as we are running in the host's error handler, otherwise arrange
for them to be triggered in eh_context.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A quick reading of scsi_error_handler() one could come away with the
impression that it does its wakeup event check while the task state is
TASK_RUNNING. In fact it sets TASK_INTERRUPTIBLE at the bottom of the
loop, but that is ~50 lines down.
Just set TASK_INTERRUPTIBLE at the top of loop and be done.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
eh is woken up automatically by the presence of failed commands,
scsi_schedule_eh is reserved for cases where there are no failed
commands. This guarantees that host_eh_sceduled is only incremented
when an explicit eh request is made.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
[fixed spurious delete of sas_ata_task_abort]
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rapid ata hotplug on a libsas controller results in cases where libsas
is waiting indefinitely on eh to perform an ata probe.
A race exists between scsi_schedule_eh() and scsi_restart_operations()
in the case when scsi_restart_operations() issues i/o to other devices
in the sas domain. When this happens the host state transitions from
SHOST_RECOVERY (set by scsi_schedule_eh) back to SHOST_RUNNING and
->host_busy is non-zero so we put the eh thread to sleep even though
->host_eh_scheduled is active.
Before putting the error handler to sleep we need to check if the
host_state needs to return to SHOST_RECOVERY for another trip through
eh. Since i/o that is released by scsi_restart_operations has been
blocked for at least one eh cycle, this implementation allows those
i/o's to run before another eh cycle starts to discourage hung task
timeouts.
Cc: <stable@vger.kernel.org>
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When managing shost->host_eh_scheduled libata assumes that there is a
1:1 shost-to-ata_port relationship. libsas creates a 1:N relationship
so it needs to manage host_eh_scheduled cumulatively at the host level.
The sched_eh and end_eh port port ops allow libsas to track when domain
devices enter/leave the "eh-pending" state under ha->lock (previously
named ha->state_lock, but it is no longer just a lock for ha->state
changes).
Since host_eh_scheduled indicates eh without backing commands pinning
the device it can be deallocated at any time. Move the taking of the
domain_device reference under the port_lock to guarantee that the
ata_port stays around for the duration of eh.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following crash results from cases where the end_device has been
removed before scsi_sysfs_add_sdev has had a chance to run.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000098
IP: [<ffffffff8115e100>] sysfs_create_dir+0x32/0xb6
...
Call Trace:
[<ffffffff8125e4a8>] kobject_add_internal+0x120/0x1e3
[<ffffffff81075149>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff8125e641>] kobject_add_varg+0x41/0x50
[<ffffffff8125e70b>] kobject_add+0x64/0x66
[<ffffffff8131122b>] device_add+0x12d/0x63a
[<ffffffff814b65ea>] ? _raw_spin_unlock_irqrestore+0x47/0x56
[<ffffffff8107de15>] ? module_refcount+0x89/0xa0
[<ffffffff8132f348>] scsi_sysfs_add_sdev+0x4e/0x28a
[<ffffffff8132dcbb>] do_scan_async+0x9c/0x145
...teach scsi_sysfs_add_devices() to check for deleted devices() before
trying to add them, and teach scsi_remove_target() how to remove targets
that have not been added via device_add().
Cc: <stable@vger.kernel.org>
Reported-by: Dariusz Majchrzak <dariusz.majchrzak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This may not fix all endian issues in this driver, but it does get the
driver working on PowerPC for a PMC SRC card. So it should at least fix
all the problems in the core and in the SRC support.
[jejb: fix >> 32 breakage reported by Fengguang Wu]
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The loop that waited for syncronous fib commands was causing a CPU stall
when a timeout actually occured.
1) Switch to using a more accurate timeout mechanism.
2) Do not pace the loop with udelay(). Use cpu_relax() to allow for
scheduling to occur.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an error occured that would shut down the driver, some in-flight
events were getting caught up, deadlocking a CPU or two.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This also stops using the "legacy crap" in Scsi_Host (shost->base is an
unsigned long).
This affected 32-bit systems that have 64-bit resource sizes, causing the
IO address to be truncated.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Introduce scsi_dh_attached_handler_name() to retrieve the name of the
scsi_dh that is attached to the scsi_device associated with the provided
request queue. Returns NULL if a scsi_dh is not attached.
Also, fix scsi_dh_{attach,detach} function header comments to document
@q rather than @sdev.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed the parentheses so the tcp push bit would be sent properly.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Avoid that the code for requeueing SCSI requests triggers a
crash by making sure that that code isn't scheduled anymore
after a device has been removed.
Also, source code inspection of __scsi_remove_device() revealed
a race condition in this function: no new SCSI requests must be
accepted for a SCSI device after device removal started.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The return value of scsi_queue_insert() is ignored by all its
callers, hence change the return type of this function into
void.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When we call scsi_unprep_request() the command associated with the request
gets destroyed and therefore drops its reference on the device. If this was
the only reference, the device may get released and we end up with a NULL
pointer deref when we call blk_requeue_request.
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org>
[jejb: enhance commend and add commit log for stable]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use blk_queue_dead() to test whether the queue is dead instead
of !sdev. Since scsi_prep_fn() may be invoked concurrently with
__scsi_remove_device(), keep the queuedata (sdev) pointer in
__scsi_remove_device(). This patch fixes a kernel oops that
can be triggered by USB device removal. See also
http://www.spinics.net/lists/linux-scsi/msg56254.html.
Other changes included in this patch:
- Swap the blk_cleanup_queue() and kfree() calls in
scsi_host_dev_release() to make that code easier to grasp.
- Remove the queue dead check from scsi_run_queue() since the
queue state can change anyway at any point in that function
where the queue lock is not held.
- Remove the queue dead check from the start of scsi_request_fn()
since it is redundant with the scsi_device_online() check.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We took this lock with spin_lock() so we should unlock it with
spin_unlock() instead of spin_unlock_irq(). This was introduced in
f2c8dc402b "[SCSI] megaraid_mbox: remove scsi_assign_lock usage".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On 64 bit systems the current code sets 32 bits of "seg" and leaves the
other 32 uninitialized. It doesn't matter since the variable is never
used. But it's still messy and we should fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If bfad_thread_workq(bfad) was not BFA_STATUS_OK then we freed "im"
and then dereferenced it.
I did a little clean up because it seemed nicer to return directly
instead of doing a superfluous goto. I looked at other functions in
this file and it seems like returning directly is standard.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If mc == BFI_MC_MAX then we're reading past the end of the
mod->mbhdlr[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Initialize atomic_t scsi_host_next_hn and ioerr_cntas per the guidelines
defined in Documentation/atomic_ops.txt
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A quote from SPC-4: "While in the unavailable primary target port
asymmetric access state, the device server shall support those of
the following commands that it supports while in the active/optimized
state: [ ... ] d) SET TARGET PORT GROUPS; [ ... ]". Hence re-enable
sending STPG to a target port group that is in the unavailable state.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix following message:-
drivers/scsi/qla4xxx/ql4_os.c:3266:5: error: symbol 'qla4xxx_post_aen_work' redeclared with different type (originally declared at drivers/scsi/qla4xxx/ql4_glbl.h:186) - incompatible argument 2 (different signedness)
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the backoff algorithm for when to retry alua rtpg
requests progresses geometrically as so:
2, 4, 8, 16, 32, 64... seconds.
This progression can lead to un-needed delay in retrying
alua rtpg requests when the rtpgs are delayed. A less
aggressive backoff algorithm that is additive would not
lead to such large jumps when delays start getting long, but
would backoff linearly:
2, 4, 6, 8, 10... seconds.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some storage arrays are known to return 'illegal request'
when an rtpg extended header request is made. T10 says the
array should ignore the bit, and return the non-extended
rtpg as the array doesn't support the request. Working
around this by retrying the rtpg request without the extended
header bit set when the extended rtpg request results in
illegal request.
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During alua transitions, an array can return transitioning
status in response to rtpg requests. These requests get
retried for a maximum of 60 seconds by default before timing
out. Sometimes this timeout isn't sufficient to allow the
array to complete the transition. T10-spc4 addresses this
under 'Report Target Port Groups' command.
This update retrieves the timeout value from the storage
array if available and retries the transitioning rtpgs
for up to the 'implied transitioning timeout' value
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ARCMSR_ARC1880_DiagWrite_ENABLE is 0x00000080 so (x | 0x00000080) is
never zero. The intent here was to test that loop until
ARCMSR_ARC1880_DiagWrite_ENABLE was turned on, but because the test was
wrong, we would do five loops regardless of whether it succeed or not.
Also I simplified the condition a little by removing the unused
assignement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As the limitation of RR312x's dma engine, the HBA can not access host memory
over 12GB. This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=14311
[alan: resurrected bug from 2009 and pushed upstream]
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix System Panic During IO Test using Medusa tool
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed system held-up when performing resource provsion through same PCI
function
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix system hang due to bad protection module parameters (CR: 130769)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed debug helper routine failed to dump CQ and EQ entries in non-MSI-X mode
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch corrects the issue caught via Smatch and reported by Dan Carpenter:
http://marc.info/?l=linux-scsi&m=133693516103343
Resolve null pointer check ordering that were odd
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Incorporate patch originally supplied by Julia Lawall <Julia.Lawall@lip6.fr>
http://marc.info/?l=linux-scsi&m=133572879711140&w=2
"It appears that mempool_free should be performed on these failures as on
the other exists from the containing functions."
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use list_for_each_entry_safe() instead of explicit cast to avoid relying on
struct layout
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During parity errors, the ramrods are not issued to FW. bnx2fc waits for the
timeout value, and proceeds with cleaning up the IOs. Since we are already
out-of-sync with FW, cleanup commands timeout too, and do not get the
completion. This operation takes 36 secs for each session to upload causing
huge delays. To fix this, bnx2fc now gets a PARITY_ERROR from cnic driver, and
upon failure, the driver does not issue any commands to the FW and finishes the
upload process sooner.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We do not hold the host lock when calling these functions,
so remove comment.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.
This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a new state SDEV_TRANSPORT_OFFLINE. It will
be used by transport classes to offline devices for cases like
when the fast_io_fail/recovery_tmo fires. In those cases we
want all IO to fail, and we have not yet escalated to dev_loss_tmo
behavior where we are removing the devices.
Currently to handle this state, transport classes are setting
the scsi_device's state to running, setting their internal
session/port structs state to something that indicates failed,
and then failing IO from some transport check in the queuecommand.
The reason for the new value is so that users can distinguish
between a device failure that is a result of a transport problem
vs the wide range of errors that devices get offlined for
when a scsi command times out and we offline the devices there.
It also fixes the confusion as to why the transport class is
failing IO, but has set the device state from blocked to running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Recent changes to add fcoe_sysfs caused libfcoe_init to call fcoe_transport_exit
in a module initialization routine. The change resulted in the below error. This
patch removes the __exit keyword from the fcoe_transport_exit definition such
that it may be called from an __init routine.
WARNING: drivers/scsi/fcoe/libfcoe.o(.init.text+0x21): Section mismatch in reference from the function init_module() to the function .exit.text:fcoe_transp
exit()
The function __init init_module() references
a function __exit fcoe_transport_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
fcoe_transport_exit() so it may be used outside an exit section.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2fc had an assumption that the fcoe interface will always start on the vlan
dev. However, some switch implementations (Eg., HP virtual connect FlexFabric)
expects the fcoe interface to be started on physical interface. Do not error
out if the netdev is not a vlan dev.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Deduplication of formats and consolidating tests
makes the object much smaller.
Add bnx2fc_debug.c, add functions for a few logging
functions (BNX2FC_IO_DBG, BNX2FC_TGT_DBG, BNX2FC_HBA_DBG).
Use printf extension %pV.
Add and use pr_fmt and pr_<level>.
Move the debug #include below structure definitions.
$ size drivers/scsi/bnx2fc/built-in.o*
text data bss dec hex filename
101563 1165 24976 127704 1f2d8 drivers/scsi/bnx2fc/built-in.o.new
138473 1109 33400 172982 2a3b6 drivers/scsi/bnx2fc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since bnx2fc_percpu_thread_create() creates percpu kthread, it makes
sense to use kthread_create_on_node() to get proper NUMA affinity for
kthread stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_wait_scan was introduced with asynchronous host scanning as a hack
for distributions that weren't using proper udev based wait for root to
appear in their initramfs scripts. In 2.6.30 Commit
c751085943
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sun Apr 12 20:06:56 2009 +0200
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Actually broke scsi_wait_scan because it renders
scsi_complete_async_scans() a nop for modular SCSI if you include
scsi_scans.h (which this module does).
The lack of bug reports is sufficient proof that this module is no
longer used.
Cc: Jeff Mahoney <jeffm@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updates newly added stats from fc_get_host_stats,
added new function fc_exch_update_stats to
update exches related stats from fc_exch.c
by going thru internal ema_list elements.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds stats to track FCP pkt and frame alloc
failure.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.
So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc provides more flexibility and with that
we can monitor some more FC specific stats for
FC exches or FCP error cases, this patch add
such new FC stats.
The patch adds *only* FC specific new stats to
existing fc_host attribute container.
Added stats names are self explanatory as
existing FC stats already has, however anyway
still added commentary along their definition
to describe them.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit a7a20d1039 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d01 ("fix async probe
regression"), so that same commit a7a20d1039 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want it to be possible for target_submit_cmd() to return errors up
to its fabric module callers. For now just update the prototype to
return an int, and update all callers to handle non-zero return values
as an error.
This is immediately useful for tcm_qla2xxx to fix a long-standing active
I/O session shutdown race, but tcm_fc, usb-gadget, and sbp-target the
fabric maintainers need to check + ACK that handling a target_submit_cmd()
failure due to session shutdown does not introduce regressions
(nab: Respin against for-next after initial NACK + update docbook comment +
fix double se_cmd init in exception path for usb-gadget)
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since we set se_session.sess_tearing_down and stop new commands from
being added to se_session.sess_cmd_list before we wait for commands to
finish when freeing a session, there's no need for a separate
sess_wait_list -- if we let new commands be added to sess_cmd_list
after setting sess_tearing_down, that would be a bug that breaks the
logic of waiting in-flight commands.
Also rename target_splice_sess_cmd_list() to
target_sess_cmd_list_set_waiting(), since we are no longer splicing
onto a separate list.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that target_submit_cmd() / target_get_sess_cmd() check
sess_tearing_down before adding commands to the list, we no longer
need the check in qlt_do_work(). In fact this check is racy anyway
(and that race is what inspired the change to add the check of
sess_tearing_down to the target core).
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The only place that sets qla_tgt_sess.tearing_down calls
target_splice_sess_cmd_list() immediately afterwards, without dropping
the lock it holds. That function sets se_session.sess_tearing_down,
so we can get rid of the qla_target-specific flag, and in the one
place that looks at the qla_tgt_sess.tearing_down flag just test
se_session.sess_tearing_down instead.
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove this command submission path which is not used by any in-tree driver.
This also removes the now unused new_cmd_map fabtric method, which a few
drivers implemented despite never calling transport_generic_handle_cdb_map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Defer the whole tcm_qla2xxx_handle_data call instead of just the error
path to the qla2xxx-internal workqueue. Also remove the useless lock around
the CMD_T_ABORTED check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: tcm-qla2xxx@qlogic.com
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ctype.h and string.h header files were included more than once.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
