These functions should have been static, and inspection shows they
are no longer used. (We used to parse mem= but we now defer that
to early_param).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as
a position-independent executable (PIE) when it is set. This involves
processing the dynamic relocations in the image in the early stages of
booting, even if the kernel is being run at the address it is linked at,
since the linker does not necessarily fill in words in the image for
which there are dynamic relocations. (In fact the linker does fill in
such words for 64-bit executables, though not for 32-bit executables,
so in principle we could avoid calling relocate() entirely when we're
running a 64-bit kernel at the linked address.)
The dynamic relocations are processed by a new function relocate(addr),
where the addr parameter is the virtual address where the image will be
run. In fact we call it twice; once before calling prom_init, and again
when starting the main kernel. This means that reloc_offset() returns
0 in prom_init (since it has been relocated to the address it is running
at), which necessitated a few adjustments.
This also changes __va and __pa to use an equivalent definition that is
simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are
constants (for 64-bit) whereas PHYSICAL_START is a variable (and
KERNELBASE ideally should be too, but isn't yet).
With this, relocatable kernels still copy themselves down to physical
address 0 and run there.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the way that the exception prologs transfer control to
the handlers in 64-bit kernels with the aim of making it possible to
have the prologs separate from the main body of the kernel. Now,
instead of computing the address of the handler by taking the top
32 bits of the paca address (to get the 0xc0000000........ part) and
ORing in something in the bottom 16 bits, we get the base address of
the kernel by doing a load from the paca and add an offset.
This also replaces an mfmsr and an ori to compute the MSR value for
the handler with a load from the paca. That makes it unnecessary to
have a separate version of EXCEPTION_PROLOG_PSERIES that forces 64-bit
mode.
We can no longer use a direct branches in the exception prolog code,
which means that the SLB miss handlers can't branch directly to
.slb_miss_realmode any more. Instead we have to compute the address
and do an indirect branch. This is conditional on CONFIG_RELOCATABLE;
for non-relocatable kernels we use a direct branch as before. (A later
change will allow CONFIG_RELOCATABLE to be set on 64-bit powerpc.)
Since the secondary CPUs on pSeries start execution in the first 0x100
bytes of real memory and then have to get to wherever the kernel is,
we can't use a direct branch to get there. Instead this changes
__secondary_hold_spinloop from a flag to a function pointer. When it
is set to a non-NULL value, the secondary CPUs jump to the function
pointed to by that value.
Finally this eliminates one code difference between 32-bit and 64-bit
by making __secondary_hold be the text address of the secondary CPU
spinloop rather than a function descriptor for it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This piece of code is broken for >2 threads, and possibly in some
other subtle ways (such as comparing a value obtained from an
"ibm,ppc-interrupt-server#s" property to a value obtained from a
"reg" property) and doesn't seem to have any useful purpose in the
first place other than a dubious warning in case NR_CPUS is too
small, which probably isn't the right place to do so.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update the architecture vector to indicate that Cooperative Memory
Overcommitment is supported if CONFIG_PPC_SMLPAR is set.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the bits to the architecture-vec so that ibm,client-architecture
lets the firmware know we support the 2.06 architecture.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a cputable entry for the POWER7 processor.
Also tell firmware that we know about POWER7.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fedora 9 works on Efika without the separate 'device-tree supplement',
thanks to the kernel's own fixups. With one exception -- because 'CHRP'
still appears on the 'machine:' line in /proc/cpuinfo, the installer
misdetects the platform and misconfigures yaboot, putting it into a PReP
boot partition instead of in the /boot filesystem where the Efika's
firmware could find it.
The kernel's fixups for Efika already correct one instance of 'chrp', in
the 'device_type' property. This fixes it in the 'CODEGEN,description'
property too, since that's what's exposed to userspace in /proc/cpuinfo.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Prune back Efika fixups to only include changes that are actually required
to get a working system. Most of the drivers can accept the compatible
properties, even if they don't match the what is recommented in the generic
names recommended practice document.
This patch also adds extra checks so that fixups are not performed blindly.
Instead, the code first verifies that the device tree is faulty before
making any changes. This way, if the Efika firmware is updated to fix
these issues, then the fixups will no longer get applied.
At this point; here is the list of fixups needed for the efika:
1. If the device_type property on the root node is 'chrp', then Linux won't
boot. Change device_type to 'efika' to avoid this condition
2. Add full interrupt list to the bestcomm node. In actual fact, the
bestcomm interrupts property is technically correct, it just doesn't
expose the same granularity as the device driver expects. All other
5200 device trees provide a separate irq number for each bestcomm
channel. Rather than hack the driver, it's simpler to fix it up
3. /builtin/sound node is missing an interrupts property
4. /builtin/ethernet node is missing a phy-handle property and the
device driver doesn't know what to do without one.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The new network driver fec_mpc52xx will not work on efika because the
firmware does not provide all required properties.
http://www.powerdeveloper.org/asset/by-id/46 has a Forth script to
create more properties. But only the phy stuff is required to get a
working network.
This should go into the kernel because its appearently
impossible to boot the script via tftp and then load the real boot
binary (yaboot or zimage).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The size passing to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The built-in IDE controller is configured in legacy mode, but the PCI
registers advertise native mode. Force the PCI class into legacy
mode. This allows pata_via to access two drives.
The Pegasos specific irq enforcement in the via82cxxx driver must stay
because there is apparently no generic way to setup irq per channel.
Tested on Pegasos2 with firmware version 20040810, and two IDE disks.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).
This enables that to work properly on P6.
This just involves setting a bit in the CAS structure as well as the
VPA. To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA. Then call H_CEDE.
The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.
Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Tell Phyp we support MSI via the client architecture support mechanism.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
reserve_mem() and stabs_alloc() are both called only from other __init
routines, so can be marked __init.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device type should be "soc" (as in lite5200.dts), compatible is
already set to "mpc5200".
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The firmware assigns irq 20/21 to the VIA IDE device on Pegasos.
But the required interrupt is 14/15.
Maybe someone confused decimal vs. hexadecimal values.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We make the efika device tree compliant with the defined bindings
(at least compliant enough). This is mostly done by mangling
the device_type and compatible properties, but also adding
some missing bits.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For PAPR partitions with large amounts of memory, the firmware has an
alternative, more compact representation for the information about the
memory in the partition and its NUMA associativity information. This
adds the code to the kernel to parse this alternative representation.
The other part of this patch is telling the firmware that we can
handle the alternative representation. There is however a subtlety
here, because the firmware will invoke a reboot if the memory
representation we request is different from the representation that
firmware is currently using. This is because firmware can't change
the representation on the fly. Further, some firmware versions used
on POWER5+ machines have a bug where this reboot leaves the machine
with an altered value of load-base, which will prevent any kernel
booting until it is reset to the normal value (0x4000). Because of
this bug, we do NOT set fake_elf.rpanote.new_mem_def = 1, and thus we
do not request the new representation on POWER5+ and earlier machines.
We do request the new representation on POWER6, which uses the
ibm,client-architecture-support call.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the "logical" PVR value used by POWER6 in "compatible" mode
to the list of PVR values that the kernel tells firmware it is able to
handle.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This problem was noticed by one of the Phyp firmware folks.
Our ibm,client-architecture-support call was failing.
This corrects the vector length parameters being passed in.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A warning is hurting my eyes when building 32 bits kernels
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Pegasos firmware doesn't create a valid "ranges" property for the
ISA bridge, thus causing translation of ISA addresses and IO ports to
fail. This fixes it, thus re-enabling proper early serial console to
work on Pegasos.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The support for Briq machines has been floating around as patches for
ages. This cleans it up and adds it once for all.
Some of this is based on initial code provided by Karsten Jeppesen
<karsten@jeppesens.com> and mostly rewritten from scratch by me.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A warning is hurting my eyes when building 32 bits kernels
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Pegasos firmware doesn't create a valid "ranges" property for the
ISA bridge, thus causing translation of ISA addresses and IO ports to
fail. This fixes it, thus re-enabling proper early serial console to
work on Pegasos.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This extends the maple device-tree workarounds to work on the
Apache board as well, and extends the maple platform probing code
to recognize the Apache board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It seems that prom_init's early_cmdline_parse is broken on at least
Apple 970 xserves and IBM JS20 blades with SLOF. The firmware of these
machines returns -1 and 1 respectively when getprop is called for the
bootargs property of /chosen, causing Linux to ignore its builtin
command line in favor of a null string. This patch makes Linux use its
builtin command line if getprop returns an error or a null string.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The IBM Cell blade firmware might confuse the kernel to think it's a
pSeries machine. This fixes it for now. With a bit of luck, the firmware
will be updated to avoid that in the future but currently that patch is
needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code in prom_init.c calling the firmware
ibm,client-architecture-support method on pSeries has a bug where it
fails to properly pass the instance handle of the firmware object when
trying to call a method. Result ranges from the call doing nothing to
the firmware crashing. (Found by Segher, thanks !)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Due to a firmware device tree bug, RTC and NVRAM accesses (including
halt/reboot) on Maple have been broken since January, when an untested
build fix went in. This code patches the device tree in Linux.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A devtree compiler (dtc) generated devtree blob is "relocatable" and so
does not contain a reserved_map entry for the blob itself. This means
that if passed to Linux, Linux will not get lmb_reserve() the blob and
it could be over. The following patch will explicitly reserve the
"blob" as it was given to us and stops prom_init.c from creating a
reserved mapping for the blob.
NOTE: that the dtc/kexec should not generate the blob reservation entry.
Although if they do, LMB reserver handles overlaps.
Signed-off-by: <jimix@watson.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently do mem= handling in three seperate places. And as benh pointed out
I wrote two of them. Now that we parse command line parameters earlier we can
clean this mess up.
Moving the parsing out of prom_init means the device tree might be allocated
above the memory limit. If that happens we'd have to move it. As it happens
we already have logic to do that for kdump, so just genericise it.
This also means we might have reserved regions above the memory limit, if we
do the bootmem allocator will blow up, so we have to modify
lmb_enforce_memory_limit() to truncate the reserves as well.
Tested on P5 LPAR, iSeries, F50, 44p. Tested moving device tree on P5 and
44p and F50.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The OF trampoline code prom_init.c still needs to identify IBM pSeries
(PAPR) machines in order to run some platform specific code on them like
instanciating the TCE tables. The code doing that detection was changed
recently in 2.6.17 early stages but was done slightly incorrectly. It
should be testing for an exact match of "chrp" and it currently tests
for anything that begins with "chrp". That means it will incorrectly
match with platforms using Maple-like device-trees and have open
firmware. This fixes it by using strcmp instead of strncmp to match what
the actual platform detection code does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a cputable entry for the POWER6 processor.
The SIHV and SIPR bits in the mmcra have moved in POWER6, so disable
support for that until oprofile is fixed.
Also tell firmware that we know about POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to call a new firmware method to tell the firmware
what machines and capabilities (such as VMX/Altivec) we support.
This will be needed on POWER5+ and POWER6 machines, and it has no
effect on past and current machines.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In e8222502ee the detection of machine types
in prom_init broke for some machines. We should be checking /device_type
instead of /model. This should make Power3 and Power4 boot again. Haven't
been able to test this. We also need to relocate before comparing.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do not call prom exit prom_panic. It clears the screen and the exit
message is lost.
On some (or all?) pmacs it causes another crash when OF tries to print
the date and time in its banner.
Set of_platform earlier to catch more prom_panic() calls.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
