Some users have reported instances of the host hanging with secondary
threads of a core waiting for the primary thread to exit the guest,
and the primary thread stuck in nap mode. This prompted a review of
the memory barriers in the guest entry/exit code, and this is the
result. Most of these changes are the suggestions of Dean Burdick
<deanburdick@us.ibm.com>.
The barriers between updating napping_threads and reading the
entry_exit_count on the one hand, and updating entry_exit_count and
reading napping_threads on the other, need to be isync not lwsync,
since we need to ensure that either the napping_threads update or the
entry_exit_count update get seen. It is not sufficient to order the
load vs. lwarx, as lwsync does; we need to order the load vs. the
stwcx., so we need isync.
In addition, we need a full sync before sending IPIs to wake other
threads from nap, to ensure that the write to the entry_exit_count is
visible before the IPI occurs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes a bug in kvmppc_do_h_enter() where the physical address
for a page can be calculated incorrectly if transparent huge pages
(THP) are active. Until THP came along, it was true that if we
encountered a large (16M) page in kvmppc_do_h_enter(), then the
associated memslot must be 16M aligned for both its guest physical
address and the userspace address, and the physical address
calculations in kvmppc_do_h_enter() assumed that. With THP, that
is no longer true.
In the case where we are using MMU notifiers and the page size that
we get from the Linux page tables is larger than the page being mapped
by the guest, we need to fill in some low-order bits of the physical
address. Without THP, these bits would be the same in the guest
physical address (gpa) and the host virtual address (hva). With THP,
they can be different, and we need to use the bits from hva rather
than gpa.
In the case where we are not using MMU notifiers, the host physical
address we get from the memslot->arch.slot_phys[] array already
includes the low-order bits down to the PAGE_SIZE level, even if
we are using large pages. Thus we can simplify the calculation in
this case to just add in the remaining bits in the case where
PAGE_SIZE is 64k and the guest is mapping a 4k page.
The same bug exists in kvmppc_book3s_hv_page_fault(). The basic fix
is to use psize (the page size from the HPTE) rather than pte_size
(the page size from the Linux PTE) when updating the HPTE low word
in r. That means that pfn needs to be computed to PAGE_SIZE
granularity even if the Linux PTE is a huge page PTE. That can be
arranged simply by doing the page_to_pfn() before setting page to
the head of the compound page. If psize is less than PAGE_SIZE,
then we need to make sure we only update the bits from PAGE_SIZE
upwards, in order not to lose any sub-page offset bits in r.
On the other hand, if psize is greater than PAGE_SIZE, we need to
make sure we don't bring in non-zero low order bits in pfn, hence
we mask (pfn << PAGE_SHIFT) with ~(psize - 1).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a
few bugfixes. ARM got transparent huge page support, improved
overcommit, and support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes
some nVidia cards on Windows, that fail to start without these
patches and the corresponding userspace changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=rWNf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM changes from Paolo Bonzini:
"Here are the 3.13 KVM changes. There was a lot of work on the PPC
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a few
bugfixes.
ARM got transparent huge page support, improved overcommit, and
support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes some
nVidia cards on Windows, that fail to start without these patches and
the corresponding userspace changes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
kvm, vmx: Fix lazy FPU on nested guest
arm/arm64: KVM: PSCI: propagate caller endianness to the incoming vcpu
arm/arm64: KVM: MMIO support for BE guest
kvm, cpuid: Fix sparse warning
kvm: Delete prototype for non-existent function kvm_check_iopl
kvm: Delete prototype for non-existent function complete_pio
hung_task: add method to reset detector
pvclock: detect watchdog reset at pvclock read
kvm: optimize out smp_mb after srcu_read_unlock
srcu: API for barrier after srcu read unlock
KVM: remove vm mmap method
KVM: IOMMU: hva align mapping page size
KVM: x86: trace cpuid emulation when called from emulator
KVM: emulator: cleanup decode_register_operand() a bit
KVM: emulator: check rex prefix inside decode_register()
KVM: x86: fix emulation of "movzbl %bpl, %eax"
kvm_host: typo fix
KVM: x86: emulate SAHF instruction
MAINTAINERS: add tree for kvm.git
Documentation/kvm: add a 00-INDEX file
...
Pull powerpc updates from Benjamin Herrenschmidt:
"The bulk of this is LE updates. One should now be able to build an LE
kernel and even run some things in it.
I'm still sitting on a handful of patches to enable the new ABI that I
*might* still send this merge window around, but due to the
incertainty (they are pretty fresh) I want to keep them separate.
Other notable changes are some infrastructure bits to better handle
PCI pass-through under KVM, some bits and pieces added to the new
PowerNV platform support such as access to the CPU SCOM bus via sysfs,
and support for EEH error handling on PHB3 (Power8 PCIe).
We also grew arch_get_random_long() for both pseries and powernv when
running on P7+ and P8, exploiting the HW rng.
And finally various embedded updates from freescale"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (154 commits)
powerpc: Fix fatal SLB miss when restoring PPR
powerpc/powernv: Reserve the correct PE number
powerpc/powernv: Add PE to its own PELTV
powerpc/powernv: Add support for indirect XSCOM via debugfs
powerpc/scom: Improve debugfs interface
powerpc/scom: Enable 64-bit addresses
powerpc/boot: Properly handle the base "of" boot wrapper
powerpc/bpf: Support MOD operation
powerpc/bpf: Fix DIVWU instruction opcode
of: Move definition of of_find_next_cache_node into common code.
powerpc: Remove big endianness assumption in of_find_next_cache_node
powerpc/tm: Remove interrupt disable in __switch_to()
powerpc: word-at-a-time optimization for 64-bit Little Endian
powerpc/bpf: BPF JIT compiler for 64-bit Little Endian
powerpc: Only save/restore SDR1 if in hypervisor mode
powerpc/pmu: Fix ADB_PMU_LED_IDE dependencies
powerpc/nvram: Fix endian issue when using the partition length
powerpc/nvram: Fix endian issue when reading the NVRAM size
powerpc/nvram: Scan partitions only once
powerpc/mpc512x: remove unnecessary #if
...
drop is_hv_enabled, because that should not be a callback property
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This moves the kvmppc_ops callbacks to be a per VM entity. This
enables us to select HV and PR mode when creating a VM. We also
allow both kvm-hv and kvm-pr kernel module to be loaded. To
achieve this we move /dev/kvm ownership to kvm.ko module. Depending on
which KVM mode we select during VM creation we take a reference
count on respective module
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[agraf: fix coding style]
Signed-off-by: Alexander Graf <agraf@suse.de>
We will use that in the later patch to find the kvm ops handler
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch moves PR related tracepoints to a separate header. This
enables in converting PR to a kernel module which will be done in
later patches
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This help us to identify whether we are running with hypervisor mode KVM
enabled. The change is needed so that we can have both HV and PR kvm
enabled in the same kernel.
If both HV and PR KVM are included, interrupts come in to the HV version
of the kvmppc_interrupt code, which then jumps to the PR handler,
renamed to kvmppc_interrupt_pr, if the guest is a PR guest.
Allowing both PR and HV in the same kernel required some changes to
kvm_dev_ioctl_check_extension(), since the values returned now can't
be selected with #ifdefs as much as previously. We look at is_hv_enabled
to return the right value when checking for capabilities.For capabilities that
are only provided by HV KVM, we return the HV value only if
is_hv_enabled is true. For capabilities provided by PR KVM but not HV,
we return the PR value only if is_hv_enabled is false.
NOTE: in later patch we replace is_hv_enabled with a static inline
function comparing kvm_ppc_ops
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
With this patch if HV is included, interrupts come in to the HV version
of the kvmppc_interrupt code, which then jumps to the PR handler,
renamed to kvmppc_interrupt_pr, if the guest is a PR guest. This helps
in enabling both HV and PR, which we do in later patch
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch add a new callback kvmppc_ops. This will help us in enabling
both HV and PR KVM together in the same kernel. The actual change to
enable them together is done in the later patch in the series.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[agraf: squash in booke changes]
Signed-off-by: Alexander Graf <agraf@suse.de>
This help ups to select the relevant code in the kernel code
when we later move HV and PR bits as seperate modules. The patch
also makes the config options for PR KVM selectable
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
With later patches supporting PR kvm as a kernel module, the changes
that has to be built into the main kernel binary to enable PR KVM module
is now selected via KVM_BOOK3S_PR_POSSIBLE
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since the code in book3s_64_vio_hv.c is called from real mode with HV
KVM, and therefore has to be built into the main kernel binary, this
makes it always built-in rather than part of the KVM module. It gets
called from the KVM module by PR KVM, so this adds an EXPORT_SYMBOL_GPL().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This label is not used now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the debug stub support on booke/bookehv.
Now QEMU debug stub can use hw breakpoint, watchpoint and
software breakpoint to debug guest.
This is how we save/restore debug register context when switching
between guest, userspace and kernel user-process:
When QEMU is running
-> thread->debug_reg == QEMU debug register context.
-> Kernel will handle switching the debug register on context switch.
-> no vcpu_load() called
QEMU makes ioctls (except RUN)
-> This will call vcpu_load()
-> should not change context.
-> Some ioctls can change vcpu debug register, context saved in vcpu->debug_regs
QEMU Makes RUN ioctl
-> Save thread->debug_reg on STACK
-> Store thread->debug_reg == vcpu->debug_reg
-> load thread->debug_reg
-> RUN VCPU ( So thread points to vcpu context )
Context switch happens When VCPU running
-> makes vcpu_load() should not load any context
-> kernel loads the vcpu context as thread->debug_regs points to vcpu context.
On heavyweight_exit
-> Load the context saved on stack in thread->debug_reg
Currently we do not support debug resource emulation to guest,
On debug exception, always exit to user space irrespective of
user space is expecting the debug exception or not. If this is
unexpected exception (breakpoint/watchpoint event not set by
userspace) then let us leave the action on user space. This
is similar to what it was before, only thing is that now we
have proper exit state available to user space.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
For KVM also use the "struct debug_reg" defined in asm/processor.h
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
"ehpriv 1" instruction is used for setting software breakpoints
by user space. This patch adds support to exit to user space
with "run->debug" have relevant information.
As this is the first point we are using run->debug, also defined
the run->debug structure.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Mark the guest page as accessed so that there is likely
less chances of this page getting swap-out.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
"G" bit in MAS2 indicates whether the page is Guarded.
There is no reason to stop guest setting "G", so allow him.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
"E" bit in MAS2 bit indicates whether the page is accessed
in Little-Endian or Big-Endian byte order.
There is no reason to stop guest setting "E", so allow him."
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
When an interrupt or exception happens in the guest that comes to the
host, the CPU goes to hypervisor real mode (MMU off) to handle the
exception but doesn't change the MMU context. After saving a few
registers, we then clear the "in guest" flag. If, for any reason,
we get an exception in the real-mode code, that then gets handled
by the normal kernel exception handlers, which turn the MMU on. This
is disastrous if the MMU is still set to the guest context, since we
end up executing instructions from random places in the guest kernel
with hypervisor privilege.
In order to catch this situation, we define a new value for the "in guest"
flag, KVM_GUEST_MODE_HOST_HV, to indicate that we are in hypervisor real
mode with guest MMU context. If the "in guest" flag is set to this value,
we branch off to an emergency handler. For the moment, this just does
a branch to self to stop the CPU from doing anything further.
While we're here, we define another new flag value to indicate that we
are in a HV guest, as distinct from a PR guest. This will be useful
when we have a kernel that can support both PR and HV guests concurrently.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
add kvmppc_free_vcores() to free the kvmppc_vcore structures
that we allocate for a guest, which are currently being leaked.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, whenever any of the MMU notifier callbacks get called, we
invalidate all the shadow PTEs. This is inefficient because it means
that we typically then get a lot of DSIs and ISIs in the guest to fault
the shadow PTEs back in. We do this even if the address range being
notified doesn't correspond to guest memory.
This commit adds code to scan the memslot array to find out what range(s)
of guest physical addresses corresponds to the host virtual address range
being affected. For each such range we flush only the shadow PTEs
for the range, on all cpus.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The mark_page_dirty() function, despite what its name might suggest,
doesn't actually mark the page as dirty as far as the MM subsystem is
concerned. It merely sets a bit in KVM's map of dirty pages, if
userspace has requested dirty tracking for the relevant memslot.
To tell the MM subsystem that the page is dirty, we have to call
kvm_set_pfn_dirty() (or an equivalent such as SetPageDirty()).
This adds a call to kvm_set_pfn_dirty(), and while we are here, also
adds a call to kvm_set_pfn_accessed() to tell the MM subsystem that
the page has been accessed. Since we are now using the pfn in
several places, this adds a 'pfn' variable to store it and changes
the places that used hpaddr >> PAGE_SHIFT to use pfn instead, which
is the same thing.
This also changes a use of HPTE_R_PP to PP_RXRX. Both are 3, but
PP_RXRX is more informative as being the read-only page permission
bit setting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When the MM code is invalidating a range of pages, it calls the KVM
kvm_mmu_notifier_invalidate_range_start() notifier function, which calls
kvm_unmap_hva_range(), which arranges to flush all the existing host
HPTEs for guest pages. However, the Linux PTEs for the range being
flushed are still valid at that point. We are not supposed to establish
any new references to pages in the range until the ...range_end()
notifier gets called. The PPC-specific KVM code doesn't get any
explicit notification of that; instead, we are supposed to use
mmu_notifier_retry() to test whether we are or have been inside a
range flush notifier pair while we have been getting a page and
instantiating a host HPTE for the page.
This therefore adds a call to mmu_notifier_retry inside
kvmppc_mmu_map_page(). This call is inside a region locked with
kvm->mmu_lock, which is the same lock that is called by the KVM
MMU notifier functions, thus ensuring that no new notification can
proceed while we are in the locked region. Inside this region we
also create the host HPTE and link the corresponding hpte_cache
structure into the lists used to find it later. We cannot allocate
the hpte_cache structure inside this locked region because that can
lead to deadlock, so we allocate it outside the region and free it
if we end up not using it.
This also moves the updates of vcpu3s->hpte_cache_count inside the
regions locked with vcpu3s->mmu_lock, and does the increment in
kvmppc_mmu_hpte_cache_map() when the pte is added to the cache
rather than when it is allocated, in order that the hpte_cache_count
is accurate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we request write access to all pages that get mapped into the
guest, even if the guest is only loading from the page. This reduces
the effectiveness of KSM because it means that we unshare every page we
access. Also, we always set the changed (C) bit in the guest HPTE if
it allows writing, even for a guest load.
This fixes both these problems. We pass an 'iswrite' flag to the
mmu.xlate() functions and to kvmppc_mmu_map_page() to indicate whether
the access is a load or a store. The mmu.xlate() functions now only
set C for stores. kvmppc_gfn_to_pfn() now calls gfn_to_pfn_prot()
instead of gfn_to_pfn() so that it can indicate whether we need write
access to the page, and get back a 'writable' flag to indicate whether
the page is writable or not. If that 'writable' flag is clear, we then
make the host HPTE read-only even if the guest HPTE allowed writing.
This means that we can get a protection fault when the guest writes to a
page that it has mapped read-write but which is read-only on the host
side (perhaps due to KSM having merged the page). Thus we now call
kvmppc_handle_pagefault() for protection faults as well as HPTE not found
faults. In kvmppc_handle_pagefault(), if the access was allowed by the
guest HPTE and we thus need to install a new host HPTE, we then need to
remove the old host HPTE if there is one. This is done with a new
function, kvmppc_mmu_unmap_page(), which uses kvmppc_mmu_pte_vflush() to
find and remove the old host HPTE.
Since the memslot-related functions require the KVM SRCU read lock to
be held, this adds srcu_read_lock/unlock pairs around the calls to
kvmppc_handle_pagefault().
Finally, this changes kvmppc_mmu_book3s_32_xlate_pte() to not ignore
guest HPTEs that don't permit access, and to return -EPERM for accesses
that are not permitted by the page protections.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Both PR and HV KVM have separate, identical copies of the
kvmppc_skip_interrupt and kvmppc_skip_Hinterrupt handlers that are
used for the situation where an interrupt happens when loading the
instruction that caused an exit from the guest. To eliminate this
duplication and make it easier to compile in both PR and HV KVM,
this moves this code to arch/powerpc/kernel/exceptions-64s.S along
with other kernel interrupt handler code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes PR KVM allocate its kvm_vcpu structs from the kvm_vcpu_cache
rather than having them embedded in the kvmppc_vcpu_book3s struct,
which is allocated with vzalloc. The reason is to reduce the
differences between PR and HV KVM in order to make is easier to have
them coexist in one kernel binary.
With this, the kvm_vcpu struct has a pointer to the kvmppc_vcpu_book3s
struct. The pointer to the kvmppc_book3s_shadow_vcpu struct has moved
from the kvmppc_vcpu_book3s struct to the kvm_vcpu struct, and is only
present for 32-bit, since it is only used for 32-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: squash in compile fix from Aneesh]
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds a per-VM mutex to provide mutual exclusion between vcpus
for accesses to and updates of the guest hashed page table (HPT).
This also makes the code use single-byte writes to the HPT entry
when updating of the reference (R) and change (C) bits. The reason
for doing this, rather than writing back the whole HPTE, is that on
non-PAPR virtual machines, the guest OS might be writing to the HPTE
concurrently, and writing back the whole HPTE might conflict with
that. Also, real hardware does single-byte writes to update R and C.
The new mutex is taken in kvmppc_mmu_book3s_64_xlate() when reading
the HPT and updating R and/or C, and in the PAPR HPT update hcalls
(H_ENTER, H_REMOVE, etc.). Having the mutex means that we don't need
to use a hypervisor lock bit in the HPT update hcalls, and we don't
need to be careful about the order in which the bytes of the HPTE are
updated by those hcalls.
The other change here is to make emulated TLB invalidations (tlbie)
effective across all vcpus. To do this we call kvmppc_mmu_pte_vflush
for all vcpus in kvmppc_ppc_book3s_64_tlbie().
For 32-bit, this makes the setting of the accessed and dirty bits use
single-byte writes, and makes tlbie invalidate shadow HPTEs for all
vcpus.
With this, PR KVM can successfully run SMP guests.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The implementation of H_ENTER in PR KVM has some errors:
* With H_EXACT not set, if the HPTEG is full, we return H_PTEG_FULL
as the return value of kvmppc_h_pr_enter, but the caller is expecting
one of the EMULATE_* values. The H_PTEG_FULL needs to go in the
guest's R3 instead.
* With H_EXACT set, if the selected HPTE is already valid, the H_ENTER
call should return a H_PTEG_FULL error.
This fixes these errors and also makes it write only the selected HPTE,
not the whole group, since only the selected HPTE has been modified.
This also micro-optimizes the calculations involving pte_index and i.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
64-bit POWER processors have a three-bit field for page protection in
the hashed page table entry (HPTE). Currently we only interpret the two
bits that were present in older versions of the architecture. The only
defined combination that has the new bit set is 110, meaning read-only
for supervisor and no access for user mode.
This adds code to kvmppc_mmu_book3s_64_xlate() to interpret the extra
bit appropriately.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, PR KVM uses 4k pages for the host-side mappings of guest
memory, regardless of the host page size. When the host page size is
64kB, we might as well use 64k host page mappings for guest mappings
of 64kB and larger pages and for guest real-mode mappings. However,
the magic page has to remain a 4k page.
To implement this, we first add another flag bit to the guest VSID
values we use, to indicate that this segment is one where host pages
should be mapped using 64k pages. For segments with this bit set
we set the bits in the shadow SLB entry to indicate a 64k base page
size. When faulting in host HPTEs for this segment, we make them
64k HPTEs instead of 4k. We record the pagesize in struct hpte_cache
for use when invalidating the HPTE.
For now we restrict the segment containing the magic page (if any) to
4k pages. It should be possible to lift this restriction in future
by ensuring that the magic 4k page is appropriately positioned within
a host 64k page.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds the code to interpret 64k HPTEs in the guest hashed page
table (HPT), 64k SLB entries, and to tell the guest about 64k pages
in kvm_vm_ioctl_get_smmu_info(). Guest 64k pages are still shadowed
by 4k pages.
This also adds another hash table to the four we have already in
book3s_mmu_hpte.c to allow us to find all the PTEs that we have
instantiated that match a given 64k guest page.
The tlbie instruction changed starting with POWER6 to use a bit in
the RB operand to indicate large page invalidations, and to use other
RB bits to indicate the base and actual page sizes and the segment
size. 64k pages came in slightly earlier, with POWER5++.
We use one bit in vcpu->arch.hflags to indicate that the emulated
cpu supports 64k pages, and another to indicate that it has the new
tlbie definition.
The KVM_PPC_GET_SMMU_INFO ioctl presents a bit of a problem, because
the MMU capabilities depend on which CPU model we're emulating, but it
is a VM ioctl not a VCPU ioctl and therefore doesn't get passed a VCPU
fd. In addition, commonly-used userspace (QEMU) calls it before
setting the PVR for any VCPU. Therefore, as a best effort we look at
the first vcpu in the VM and return 64k pages or not depending on its
capabilities. We also make the PVR default to the host PVR on recent
CPUs that support 1TB segments (and therefore multiple page sizes as
well) so that KVM_PPC_GET_SMMU_INFO will include 64k page and 1TB
segment support on those CPUs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently PR-style KVM keeps the volatile guest register values
(R0 - R13, CR, LR, CTR, XER, PC) in a shadow_vcpu struct rather than
the main kvm_vcpu struct. For 64-bit, the shadow_vcpu exists in two
places, a kmalloc'd struct and in the PACA, and it gets copied back
and forth in kvmppc_core_vcpu_load/put(), because the real-mode code
can't rely on being able to access the kmalloc'd struct.
This changes the code to copy the volatile values into the shadow_vcpu
as one of the last things done before entering the guest. Similarly
the values are copied back out of the shadow_vcpu to the kvm_vcpu
immediately after exiting the guest. We arrange for interrupts to be
still disabled at this point so that we can't get preempted on 64-bit
and end up copying values from the wrong PACA.
This means that the accessor functions in kvm_book3s.h for these
registers are greatly simplified, and are same between PR and HV KVM.
In places where accesses to shadow_vcpu fields are now replaced by
accesses to the kvm_vcpu, we can also remove the svcpu_get/put pairs.
Finally, on 64-bit, we don't need the kmalloc'd struct at all any more.
With this, the time to read the PVR one million times in a loop went
from 567.7ms to 575.5ms (averages of 6 values), an increase of about
1.4% for this worse-case test for guest entries and exits. The
standard deviation of the measurements is about 11ms, so the
difference is only marginally significant statistically.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 9d1ffdd8f3 ("KVM: PPC: Book3S PR: Don't corrupt guest state
when kernel uses VMX") added a call to kvmppc_load_up_altivec() that
isn't guarded by CONFIG_ALTIVEC, causing a link failure when building
a kernel without CONFIG_ALTIVEC set. This adds an #ifdef to fix this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If we come out of a guest with an interrupt that we don't know about,
instead of crashing the host with a BUG(), we now return to userspace
with the exit reason set to KVM_EXIT_UNKNOWN and the trap vector in
the hw.hardware_exit_reason field of the kvm_run structure, as is done
on x86. Note that run->exit_reason is already set to KVM_EXIT_UNKNOWN
at the beginning of kvmppc_handle_exit().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables us to use the Processor Compatibility Register (PCR) on
POWER7 to put the processor into architecture 2.05 compatibility mode
when running a guest. In this mode the new instructions and registers
that were introduced on POWER7 are disabled in user mode. This
includes all the VSX facilities plus several other instructions such
as ldbrx, stdbrx, popcntw, popcntd, etc.
To select this mode, we have a new register accessible through the
set/get_one_reg interface, called KVM_REG_PPC_ARCH_COMPAT. Setting
this to zero gives the full set of capabilities of the processor.
Setting it to one of the "logical" PVR values defined in PAPR puts
the vcpu into the compatibility mode for the corresponding
architecture level. The supported values are:
0x0f000002 Architecture 2.05 (POWER6)
0x0f000003 Architecture 2.06 (POWER7)
0x0f100003 Architecture 2.06+ (POWER7+)
Since the PCR is per-core, the architecture compatibility level and
the corresponding PCR value are stored in the struct kvmppc_vcore, and
are therefore shared between all vcpus in a virtual core.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: squash in fix to add missing break statements and documentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER7 and later IBM server processors have a register called the
Program Priority Register (PPR), which controls the priority of
each hardware CPU SMT thread, and affects how fast it runs compared
to other SMT threads. This priority can be controlled by writing to
the PPR or by use of a set of instructions of the form or rN,rN,rN
which are otherwise no-ops but have been defined to set the priority
to particular levels.
This adds code to context switch the PPR when entering and exiting
guests and to make the PPR value accessible through the SET/GET_ONE_REG
interface. When entering the guest, we set the PPR as late as
possible, because if we are setting a low thread priority it will
make the code run slowly from that point on. Similarly, the
first-level interrupt handlers save the PPR value in the PACA very
early on, and set the thread priority to the medium level, so that
the interrupt handling code runs at a reasonable speed.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds the ability to have a separate LPCR (Logical Partitioning
Control Register) value relating to a guest for each virtual core,
rather than only having a single value for the whole VM. This
corresponds to what real POWER hardware does, where there is a LPCR
per CPU thread but most of the fields are required to have the same
value on all active threads in a core.
The per-virtual-core LPCR can be read and written using the
GET/SET_ONE_REG interface. Userspace can can only modify the
following fields of the LPCR value:
DPFD Default prefetch depth
ILE Interrupt little-endian
TC Translation control (secondary HPT hash group search disable)
We still maintain a per-VM default LPCR value in kvm->arch.lpcr, which
contains bits relating to memory management, i.e. the Virtualized
Partition Memory (VPM) bits and the bits relating to guest real mode.
When this default value is updated, the update needs to be propagated
to the per-vcore values, so we add a kvmppc_update_lpcr() helper to do
that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix whitespace]
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes the VRSAVE register value for a vcpu accessible through
the GET/SET_ONE_REG interface on Book E systems (in addition to the
existing GET/SET_SREGS interface), for consistency with Book 3S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The yield count in the VPA is supposed to be incremented every time
we enter the guest, and every time we exit the guest, so that its
value is even when the vcpu is running in the guest and odd when it
isn't. However, it's currently possible that we increment the yield
count on the way into the guest but then find that other CPU threads
are already exiting the guest, so we go back to nap mode via the
secondary_too_late label. In this situation we don't increment the
yield count again, breaking the relationship between the LSB of the
count and whether the vcpu is in the guest.
To fix this, we move the increment of the yield count to a point
after we have checked whether other CPU threads are exiting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This moves the code in book3s_hv_rmhandlers.S that reads any pending
interrupt from the XICS interrupt controller, and works out whether
it is an IPI for the guest, an IPI for the host, or a device interrupt,
into a new function called kvmppc_read_intr. Later patches will
need this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We have two paths into and out of the low-level guest entry and exit
code: from a vcpu task via kvmppc_hv_entry_trampoline, and from the
system reset vector for an offline secondary thread on POWER7 via
kvm_start_guest. Currently both just branch to kvmppc_hv_entry to
enter the guest, and on guest exit, we test the vcpu physical thread
ID to detect which way we came in and thus whether we should return
to the vcpu task or go back to nap mode.
In order to make the code flow clearer, and to keep the code relating
to each flow together, this turns kvmppc_hv_entry into a subroutine
that follows the normal conventions for call and return. This means
that kvmppc_hv_entry_trampoline() and kvmppc_hv_entry() now establish
normal stack frames, and we use the normal stack slots for saving
return addresses rather than local_paca->kvm_hstate.vmhandler. Apart
from that this is mostly moving code around unchanged.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The H_CONFER hypercall is used when a guest vcpu is spinning on a lock
held by another vcpu which has been preempted, and the spinning vcpu
wishes to give its timeslice to the lock holder. We implement this
in the straightforward way using kvm_vcpu_yield_to().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The VRSAVE register value for a vcpu is accessible through the
GET/SET_SREGS interface for Book E processors, but not for Book 3S
processors. In order to make this accessible for Book 3S processors,
this adds a new register identifier for GET/SET_ONE_REG, and adds
the code to implement it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows guests to have a different timebase origin from the host.
This is needed for migration, where a guest can migrate from one host
to another and the two hosts might have a different timebase origin.
However, the timebase seen by the guest must not go backwards, and
should go forwards only by a small amount corresponding to the time
taken for the migration.
Therefore this provides a new per-vcpu value accessed via the one_reg
interface using the new KVM_REG_PPC_TB_OFFSET identifier. This value
defaults to 0 and is not modified by KVM. On entering the guest, this
value is added onto the timebase, and on exiting the guest, it is
subtracted from the timebase.
This is only supported for recent POWER hardware which has the TBU40
(timebase upper 40 bits) register. Writing to the TBU40 register only
alters the upper 40 bits of the timebase, leaving the lower 24 bits
unchanged. This provides a way to modify the timebase for guest
migration without disturbing the synchronization of the timebase
registers across CPU cores. The kernel rounds up the value given
to a multiple of 2^24.
Timebase values stored in KVM structures (struct kvm_vcpu, struct
kvmppc_vcore, etc.) are stored as host timebase values. The timebase
values in the dispatch trace log need to be guest timebase values,
however, since that is read directly by the guest. This moves the
setting of vcpu->arch.dec_expires on guest exit to a point after we
have restored the host timebase so that vcpu->arch.dec_expires is a
host timebase value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we are not saving and restoring the SIAR and SDAR registers in
the PMU (performance monitor unit) on guest entry and exit. The result
is that performance monitoring tools in the guest could get false
information about where a program was executing and what data it was
accessing at the time of a performance monitor interrupt. This fixes
it by saving and restoring these registers along with the other PMU
registers on guest entry/exit.
This also provides a way for userspace to access these values for a
vcpu via the one_reg interface.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Topic branch for commits that the KVM tree might want to pull
in separately.
Hand merged a few files due to conflicts with the LE stuff
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This creates new 'thread_fp_state' and 'thread_vr_state' structures
to store FP/VSX state (including FPSCR) and Altivec/VSX state
(including VSCR), and uses them in the thread_struct. In the
thread_fp_state, the FPRs and VSRs are represented as u64 rather
than double, since we rarely perform floating-point computations
on the values, and this will enable the structures to be used
in KVM code as well. Similarly FPSCR is now a u64 rather than
a structure of two 32-bit values.
This takes the offsets out of the macros such as SAVE_32FPRS,
REST_32FPRS, etc. This enables the same macros to be used for normal
and transactional state, enabling us to delete the transactional
versions of the macros. This also removes the unused do_load_up_fpu
and do_load_up_altivec, which were in fact buggy since they didn't
create large enough stack frames to account for the fact that
load_up_fpu and load_up_altivec are not designed to be called from C
and assume that their caller's stack frame is an interrupt frame.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a number of KVM issues with little endian builds.
We are working on fixing them, but in the meantime disable
it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the MM code is invalidating a range of pages, it calls the KVM
kvm_mmu_notifier_invalidate_range_start() notifier function, which calls
kvm_unmap_hva_range(), which arranges to flush all the TLBs for guest pages.
However, the Linux PTEs for the range being flushed are still valid at
that point. We are not supposed to establish any new references to pages
in the range until the ...range_end() notifier gets called.
The PPC-specific KVM code doesn't get any explicit notification of that;
instead, we are supposed to use mmu_notifier_retry() to test whether we
are or have been inside a range flush notifier pair while we have been
referencing a page.
This patch calls the mmu_notifier_retry() while mapping the guest
page to ensure we are not referencing a page when in range invalidation.
This call is inside a region locked with kvm->mmu_lock, which is the
same lock that is called by the KVM MMU notifier functions, thus
ensuring that no new notification can proceed while we are in the
locked region.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Acked-by: Alexander Graf <agraf@suse.de>
[Backported to 3.12 - Paolo]
Reviewed-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes a typo in the code that saves the guest DSCR (Data Stream
Control Register) into the kvm_vcpu_arch struct on guest exit. The
effect of the typo was that the DSCR value was saved in the wrong place,
so changes to the DSCR by the guest didn't persist across guest exit
and entry, and some host kernel memory got corrupted.
Cc: stable@vger.kernel.org [v3.1+]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Pull vfs pile 1 from Al Viro:
"Unfortunately, this merge window it'll have a be a lot of small piles -
my fault, actually, for not keeping #for-next in anything that would
resemble a sane shape ;-/
This pile: assorted fixes (the first 3 are -stable fodder, IMO) and
cleanups + %pd/%pD formats (dentry/file pathname, up to 4 last
components) + several long-standing patches from various folks.
There definitely will be a lot more (starting with Miklos'
check_submount_and_drop() series)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
direct-io: Handle O_(D)SYNC AIO
direct-io: Implement generic deferred AIO completions
add formats for dentry/file pathnames
kvm eventfd: switch to fdget
powerpc kvm: use fdget
switch fchmod() to fdget
switch epoll_ctl() to fdget
switch copy_module_from_fd() to fdget
git simplify nilfs check for busy subtree
ibmasmfs: don't bother passing superblock when not needed
don't pass superblock to hypfs_{mkdir,create*}
don't pass superblock to hypfs_diag_create_files
don't pass superblock to hypfs_vm_create_files()
oprofile: get rid of pointless forward declarations of struct super_block
oprofilefs_create_...() do not need superblock argument
oprofilefs_mkdir() doesn't need superblock argument
don't bother with passing superblock to oprofile_create_stats_files()
oprofile: don't bother with passing superblock to ->create_files()
don't bother passing sb to oprofile_create_files()
coh901318: don't open-code simple_read_from_buffer()
...
This reworks kvmppc_mmu_book3s_64_xlate() to make it check the large
page bit in the hashed page table entries (HPTEs) it looks at, and
to simplify and streamline the code. The checking of the first dword
of each HPTE is now done with a single mask and compare operation,
and all the code dealing with the matching HPTE, if we find one,
is consolidated in one place in the main line of the function flow.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
It turns out that if we exit the guest due to a hcall instruction (sc 1),
and the loading of the instruction in the guest exit path fails for any
reason, the call to kvmppc_ld() in kvmppc_get_last_inst() fetches the
instruction after the hcall instruction rather than the hcall itself.
This in turn means that the instruction doesn't get recognized as an
hcall in kvmppc_handle_exit_pr() but gets passed to the guest kernel
as a sc instruction. That usually results in the guest kernel getting
a return code of 38 (ENOSYS) from an hcall, which often triggers a
BUG_ON() or other failure.
This fixes the problem by adding a new variant of kvmppc_get_last_inst()
called kvmppc_get_last_sc(), which fetches the instruction if necessary
from pc - 4 rather than pc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the code assumes that once we load up guest FP/VSX or VMX
state into the CPU, it stays valid in the CPU registers until we
explicitly flush it to the thread_struct. However, on POWER7,
copy_page() and memcpy() can use VMX. These functions do flush the
VMX state to the thread_struct before using VMX instructions, but if
this happens while we have guest state in the VMX registers, and we
then re-enter the guest, we don't reload the VMX state from the
thread_struct, leading to guest corruption. This has been observed
to cause guest processes to segfault.
To fix this, we check before re-entering the guest that all of the
bits corresponding to facilities owned by the guest, as expressed
in vcpu->arch.guest_owned_ext, are set in current->thread.regs->msr.
Any bits that have been cleared correspond to facilities that have
been used by kernel code and thus flushed to the thread_struct, so
for them we reload the state from the thread_struct.
We also need to check current->thread.regs->msr before calling
giveup_fpu() or giveup_altivec(), since if the relevant bit is
clear, the state has already been flushed to the thread_struct and
to flush it again would corrupt it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 8e44ddc3f3 ("powerpc/kvm/book3s: Add support for H_IPOLL and
H_XIRR_X in XICS emulation") added a call to get_tb() but didn't
include the header that defines it, and on some configs this means
book3s_xics.c fails to compile:
arch/powerpc/kvm/book3s_xics.c: In function ‘kvmppc_xics_hcall’:
arch/powerpc/kvm/book3s_xics.c:812:3: error: implicit declaration of function ‘get_tb’ [-Werror=implicit-function-declaration]
Cc: stable@vger.kernel.org [v3.10, v3.11]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
err was overwritten by a previous function call, and checked to be 0. If
the following page allocation fails, 0 is going to be returned instead
of -ENOMEM.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
'rmls' is 'unsigned long', lpcr_rmls() will return negative number when
failure occurs, so it need a type cast for comparing.
'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number
when failure occurs, so it need a type cast for comparing.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
KVM uses anon_inode_get() to allocate file descriptors as part
of some of its ioctls. But those ioctls are lacking a flag argument
allowing userspace to choose options for the newly opened file descriptor.
In such case it's advised to use O_CLOEXEC by default so that
userspace is allowed to choose, without race, if the file descriptor
is going to be inherited across exec().
This patch set O_CLOEXEC flag on all file descriptors created
with anon_inode_getfd() to not leak file descriptors across exec().
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://lkml.kernel.org/r/cover.1377372576.git.ydroneaud@opteya.com
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Our ppc64 spinlocks and rwlocks use a trick where a lock token and
the paca index are placed in the lock with a single store. Since we
are using two u16s they need adjusting for little endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lppaca, slb_shadow and dtl_entry hypervisor structures are
big endian, so we have to byte swap them in little endian builds.
LE KVM hosts will also need to be fixed but for now add an #error
to remind us.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Although the shared_proc field in the lppaca works today, it is
not architected. A shared processor partition will always have a non
zero yield_count so use that instead. Create a wrapper so users
don't have to know about the details.
In order for older kernels to continue to work on KVM we need
to set the shared_proc bit. While here, remove the ugly bitfield.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
err was overwritten by a previous function call, and checked to be 0. If
the following page allocation fails, 0 is going to be returned instead
of -ENOMEM.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
'rmls' is 'unsigned long', lpcr_rmls() will return negative number when
failure occurs, so it need a type cast for comparing.
'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number
when failure occurs, so it need a type cast for comparing.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Opcode and xopcode are useful definitions not just for KVM. Move these
definitions to asm/ppc-opcode.h for public use.
Also add the opcodes for LHAUX and LWZUX.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
[scottwood@freesacle.com: update commit message and rebase]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Unlike the other general-purpose SPRs, SPRG3 can be read by usermode
code, and is used in recent kernels to store the CPU and NUMA node
numbers so that they can be read by VDSO functions. Thus we need to
load the guest's SPRG3 value into the real SPRG3 register when entering
the guest, and restore the host's value when exiting the guest. We don't
need to save the guest SPRG3 value when exiting the guest as usermode
code can't modify SPRG3.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is called right after the memslots is updated, i.e. when the result
of update_memslots() gets installed in install_new_memslots(). Since
the memslots needs to be updated twice when we delete or move a memslot,
kvm_arch_commit_memory_region() does not correspond to this exactly.
In the following patch, x86 will use this new API to check if the mmio
generation has reached its maximum value, in which case mmio sptes need
to be flushed out.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Acked-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_guest_enter() was already called by kvmppc_prepare_to_enter().
Don't call it again.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently this is only being done on 64-bit. Rather than just move it
out of the 64-bit ifdef, move it to kvm_lazy_ee_enable() so that it is
consistent with lazy ee state, and so that we don't track more host
code as interrupts-enabled than necessary.
Rename kvm_lazy_ee_enable() to kvm_fix_ee_before_entry() to reflect
that this function now has a role on 32-bit as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The table of offsets to real-mode hcall handlers in book3s_hv_rmhandlers.S
can contain negative values, if some of the handlers end up before the
table in the vmlinux binary. Thus we need to use a sign-extending load
to read the values in the table rather than a zero-extending load.
Without this, the host crashes when the guest does one of the hcalls
with negative offsets, due to jumping to a bogus address.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This corrects the usage of the tlbie (TLB invalidate entry) instruction
in HV KVM. The tlbie instruction changed between PPC970 and POWER7.
On the PPC970, the bit to select large vs. small page is in the instruction,
not in the RB register value. This changes the code to use the correct
form on PPC970.
On POWER7 we were calculating the AVAL (Abbreviated Virtual Address, Lower)
field of the RB value incorrectly for 64k pages. This fixes it.
Since we now have several cases to handle for the tlbie instruction, this
factors out the code to do a sequence of tlbies into a new function,
do_tlbies(), and calls that from the various places where the code was
doing tlbie instructions inline. It also makes kvmppc_h_bulk_remove()
use the same global_invalidates() function for determining whether to do
local or global TLB invalidations as is used in other places, for
consistency, and also to make sure that kvm->arch.need_tlb_flush gets
updated properly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Both RMA and hash page table request will be a multiple of 256K. We can use
a chunk size of 256K to track the free/used 256K chunk in the bitmap. This
should help to reduce the bitmap size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Older version of power architecture use Real Mode Offset register and Real Mode Limit
Selector for mapping guest Real Mode Area. The guest RMA should be physically
contigous since we use the range when address translation is not enabled.
This patch switch RMA allocation code to use contigous memory allocator. The patch
also remove the the linear allocator which not used any more
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Powerpc architecture uses a hash based page table mechanism for mapping virtual
addresses to physical address. The architecture require this hash page table to
be physically contiguous. With KVM on Powerpc currently we use early reservation
mechanism for allocating guest hash page table. This implies that we need to
reserve a big memory region to ensure we can create large number of guest
simultaneously with KVM on Power. Another disadvantage is that the reserved memory
is not available to rest of the subsystems and and that implies we limit the total
available memory in the host.
This patch series switch the guest hash page table allocation to use
contiguous memory allocator.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We don't emulate breakpoints yet, so just ignore reads and writes
to / from DABR.
This fixes booting of more recent Linux guest kernels for me.
Reported-by: Nello Martuscielli <ppc.addon@gmail.com>
Tested-by: Nello Martuscielli <ppc.addon@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc changes for the 3.11 merge window. In addition to
the usual bug fixes and small updates, the main highlights are:
- Support for transparent huge pages by Aneesh Kumar for 64-bit
server processors. This allows the use of 16M pages as transparent
huge pages on kernels compiled with a 64K base page size.
- Base VFIO support for KVM on power by Alexey Kardashevskiy
- Wiring up of our nvram to the pstore infrastructure, including
putting compressed oopses in there by Aruna Balakrishnaiah
- Move, rework and improve our "EEH" (basically PCI error handling
and recovery) infrastructure. It is no longer specific to pseries
but is now usable by the new "powernv" platform as well (no
hypervisor) by Gavin Shan.
- I fixed some bugs in our math-emu instruction decoding and made it
usable to emulate some optional FP instructions on processors with
hard FP that lack them (such as fsqrt on Freescale embedded
processors).
- Support for Power8 "Event Based Branch" facility by Michael
Ellerman. This facility allows what is basically "userspace
interrupts" for performance monitor events.
- A bunch of Transactional Memory vs. Signals bug fixes and HW
breakpoint/watchpoint fixes by Michael Neuling.
And more ... I appologize in advance if I've failed to highlight
something that somebody deemed worth it."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
pstore: Add hsize argument in write_buf call of pstore_ftrace_call
powerpc/fsl: add MPIC timer wakeup support
powerpc/mpic: create mpic subsystem object
powerpc/mpic: add global timer support
powerpc/mpic: add irq_set_wake support
powerpc/85xx: enable coreint for all the 64bit boards
powerpc/8xx: Erroneous double irq_eoi() on CPM IRQ in MPC8xx
powerpc/fsl: Enable CONFIG_E1000E in mpc85xx_smp_defconfig
powerpc/mpic: Add get_version API both for internal and external use
powerpc: Handle both new style and old style reserve maps
powerpc/hw_brk: Fix off by one error when validating DAWR region end
powerpc/pseries: Support compression of oops text via pstore
powerpc/pseries: Re-organise the oops compression code
pstore: Pass header size in the pstore write callback
powerpc/powernv: Fix iommu initialization again
powerpc/pseries: Inform the hypervisor we are using EBB regs
powerpc/perf: Add power8 EBB support
powerpc/perf: Core EBB support for 64-bit book3s
powerpc/perf: Drop MMCRA from thread_struct
powerpc/perf: Don't enable if we have zero events
...
On the x86 side, there are some optimizations and documentation updates.
The big ARM/KVM change for 3.11, support for AArch64, will come through
Catalin Marinas's tree. s390 and PPC have misc cleanups and bugfixes.
There is a conflict due to "s390/pgtable: fix ipte notify bit" having
entered 3.10 through Martin Schwidefsky's s390 tree. This pull request
has additional changes on top, so this tree's version is the correct one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=1zpG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"On the x86 side, there are some optimizations and documentation
updates. The big ARM/KVM change for 3.11, support for AArch64, will
come through Catalin Marinas's tree. s390 and PPC have misc cleanups
and bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (87 commits)
KVM: PPC: Ignore PIR writes
KVM: PPC: Book3S PR: Invalidate SLB entries properly
KVM: PPC: Book3S PR: Allow guest to use 1TB segments
KVM: PPC: Book3S PR: Don't keep scanning HPTEG after we find a match
KVM: PPC: Book3S PR: Fix invalidation of SLB entry 0 on guest entry
KVM: PPC: Book3S PR: Fix proto-VSID calculations
KVM: PPC: Guard doorbell exception with CONFIG_PPC_DOORBELL
KVM: Fix RTC interrupt coalescing tracking
kvm: Add a tracepoint write_tsc_offset
KVM: MMU: Inform users of mmio generation wraparound
KVM: MMU: document fast invalidate all mmio sptes
KVM: MMU: document fast invalidate all pages
KVM: MMU: document fast page fault
KVM: MMU: document mmio page fault
KVM: MMU: document write_flooding_count
KVM: MMU: document clear_spte_count
KVM: MMU: drop kvm_mmu_zap_mmio_sptes
KVM: MMU: init kvm generation close to mmio wrap-around value
KVM: MMU: add tracepoint for check_mmio_spte
KVM: MMU: fast invalidate all mmio sptes
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR0K2gAAoJEHm+PkMAQRiGWsEH+gMZSN1qRm34hZ82q1Tx7HvL
Eb/Gsl3Qw/7G2TlTqgjBUs36IdqV9O2cui/aa3/TfXvdvrx+0GlhRkEwQPc+ygcO
Mvoyoke4tT4+4jVFdCg1J8avREsa28/6oaHs0ZZxuVmJBBLTJH7aXaNsGn6eU1q9
9+p798MQis6naIiPC63somlZcCIiBhsuWCPWpEfLMn8G1HWAFTM3xXIbNBqe/brS
bmIOfhomlIZ5dcdaXGvjtP3+KJhkNDwhkPC4tVYu8JqqgSlrE+a+EGyEuuGqKk10
U+swiqyuD31uBI9ga54u/2FzSqDiAu6YOcMXevjo/m3g9XLdYbYLvN+nvN8alCQ=
=Ob6Z
-----END PGP SIGNATURE-----
Merge tag 'v3.10' into next
Merge 3.10 in order to get some of the last minute powerpc
changes, resolve conflicts and add additional fixes on top
of them.
While technically it's legal to write to PIR and have the identifier changed,
we don't implement logic to do so because we simply expose vcpu_id to the guest.
So instead, let's ignore writes to PIR. This ensures that we don't inject faults
into the guest for something the guest is allowed to do. While at it, we cross
our fingers hoping that it also doesn't mind that we broke its PIR read values.
Signed-off-by: Alexander Graf <agraf@suse.de>
At present, if the guest creates a valid SLB (segment lookaside buffer)
entry with the slbmte instruction, then invalidates it with the slbie
instruction, then reads the entry with the slbmfee/slbmfev instructions,
the result of the slbmfee will have the valid bit set, even though the
entry is not actually considered valid by the host. This is confusing,
if not worse. This fixes it by zeroing out the orige and origv fields
of the SLB entry structure when the entry is invalidated.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
With this, the guest can use 1TB segments as well as 256MB segments.
Since we now have the situation where a single emulated guest segment
could correspond to multiple shadow segments (as the shadow segments
are still 256MB segments), this adds a new kvmppc_mmu_flush_segment()
to scan for all shadow segments that need to be removed.
This restructures the guest HPT (hashed page table) lookup code to
use the correct hashing and matching functions for HPTEs within a
1TB segment. We use the standard hpt_hash() function instead of
open-coding the hash calculation, and we use HPTE_V_COMPARE() with
an AVPN value that has the B (segment size) field included. The
calculation of avpn is done a little earlier since it doesn't change
in the loop starting at the do_second label.
The computation in kvmppc_mmu_book3s_64_esid_to_vsid() changes so that
it returns a 256MB VSID even if the guest SLB entry is a 1TB entry.
This is because the users of this function are creating 256MB SLB
entries. We set a new VSID_1T flag so that entries created from 1T
segments don't collide with entries from 256MB segments.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The loop in kvmppc_mmu_book3s_64_xlate() that looks up a translation
in the guest hashed page table (HPT) keeps going if it finds an
HPTE that matches but doesn't allow access. This is incorrect; it
is different from what the hardware does, and there should never be
more than one matching HPTE anyway. This fixes it to stop when any
matching HPTE is found.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
On entering a PR KVM guest, we invalidate the whole SLB before loading
up the guest entries. We do this using an slbia instruction, which
invalidates all entries except entry 0, followed by an slbie to
invalidate entry 0. However, the slbie turns out to be ineffective
in some circumstances (specifically when the host linear mapping uses
64k pages) because of errors in computing the parameter to the slbie.
The result is that the guest kernel hangs very early in boot because
it takes a DSI the first time it tries to access kernel data using
a linear mapping address in real mode.
Currently we construct bits 36 - 43 (big-endian numbering) of the slbie
parameter by taking bits 56 - 63 of the SLB VSID doubleword. These bits
for the tlbie are C (class, 1 bit), B (segment size, 2 bits) and 5
reserved bits. For the SLB VSID doubleword these are C (class, 1 bit),
reserved (1 bit), LP (large page size, 2 bits), and 4 reserved bits.
Thus we are not setting the B field correctly, and when LP = 01 as
it is for 64k pages, we are setting a reserved bit.
Rather than add more instructions to calculate the slbie parameter
correctly, this takes a simpler approach, which is to set entry 0 to
zeroes explicitly. Normally slbmte should not be used to invalidate
an entry, since it doesn't invalidate the ERATs, but it is OK to use
it to invalidate an entry if it is immediately followed by slbia,
which does invalidate the ERATs. (This has been confirmed with the
Power architects.) This approach takes fewer instructions and will
work whatever the contents of entry 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes sure the calculation of the proto-VSIDs used by PR KVM
is done with 64-bit arithmetic. Since vcpu3s->context_id[] is int,
when we do vcpu3s->context_id[0] << ESID_BITS the shift will be done
with 32-bit instructions, possibly leading to significant bits
getting lost, as the context id can be up to 524283 and ESID_BITS is
18. To fix this we cast the context id to u64 before shifting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Availablity of the doorbell_exception function is guarded by
CONFIG_PPC_DOORBELL. Use the same define to guard our caller
of it.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[agraf: improve patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
We can find pte that are splitting while walking page tables. Return
None pte in that case.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace find_linux_pte with find_linux_pte_or_hugepte and explicitly
document why we don't need to handle transparent hugepages at callsites.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate. With hugepages, we need to pass the correct
actual page size value for tlb invalidation.
This change update the patch 0608d69246
"powerpc/mm: Always invalidate tlb on hpte invalidate and update" to handle
transparent hugepages correctly.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull RCU changes from Paul E. McKenney:
"The major changes for this series are:
1. Simplify RCU's grace-period and callback processing based on
the new numbering for callbacks. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/330.
2. Documentation updates. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/348.
3. Miscellaneous fixes, including converting a few remaining printk()
calls to pr_*(). These were posted to LKML at
https://lkml.org/lkml/2013/5/20/324.
4. SRCU-related changes and fixes. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/425.
5. Removal of TINY_PREEMPT_RCU in favor of TREE_PREEMPT_RCU for
single-CPU low-latency systems. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/427."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
kwmppc_lazy_ee_enable() should be called as late as possible,
or else we get things like WARN_ON(preemptible()) in enable_kernel_fp()
in configurations where preemptible() works.
Note that book3s_pr already waits until just before __kvmppc_vcpu_run
to call kvmppc_lazy_ee_enable().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
EE is hard-disabled on entry to kvmppc_handle_exit(), so call
hard_irq_disable() so that PACA_IRQ_HARD_DIS is set, and soft_enabled
is unset.
Without this, we get warnings such as arch/powerpc/kernel/time.c:300,
and sometimes host kernel hangs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
KVM core expects arch code to acquire the srcu lock when calling
gfn_to_memslot and similar functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The previous patch made 64-bit booke KVM build again, but Altivec
support is still not complete, and we can't prevent the guest from
turning on Altivec (which can corrupt host state until state
save/restore is implemented). Disable e6500 on KVM until this is
fixed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
At the point of up_out label in kvmppc_hv_setup_htab_rma(),
srcu read lock is still held.
We have to release it before return.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: kvm@vger.kernel.org
Cc: kvm-ppc@vger.kernel.org
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X. H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state. H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor. Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.
These hcalls are not currently used by Linux guests, but may be in
future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As requested by the KVM maintainers, remove the addprefix used to
refer to the main KVM code from the arch code, and replace it with
a KVM variable that does the same thing.
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Pull kvm updates from Gleb Natapov:
"Highlights of the updates are:
general:
- new emulated device API
- legacy device assignment is now optional
- irqfd interface is more generic and can be shared between arches
x86:
- VMCS shadow support and other nested VMX improvements
- APIC virtualization and Posted Interrupt hardware support
- Optimize mmio spte zapping
ppc:
- BookE: in-kernel MPIC emulation with irqfd support
- Book3S: in-kernel XICS emulation (incomplete)
- Book3S: HV: migration fixes
- BookE: more debug support preparation
- BookE: e6500 support
ARM:
- reworking of Hyp idmaps
s390:
- ioeventfd for virtio-ccw
And many other bug fixes, cleanups and improvements"
* tag 'kvm-3.10-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
kvm: Add compat_ioctl for device control API
KVM: x86: Account for failing enable_irq_window for NMI window request
KVM: PPC: Book3S: Add API for in-kernel XICS emulation
kvm/ppc/mpic: fix missing unlock in set_base_addr()
kvm/ppc: Hold srcu lock when calling kvm_io_bus_read/write
kvm/ppc/mpic: remove users
kvm/ppc/mpic: fix mmio region lists when multiple guests used
kvm/ppc/mpic: remove default routes from documentation
kvm: KVM_CAP_IOMMU only available with device assignment
ARM: KVM: iterate over all CPUs for CPU compatibility check
KVM: ARM: Fix spelling in error message
ARM: KVM: define KVM_ARM_MAX_VCPUS unconditionally
KVM: ARM: Fix API documentation for ONE_REG encoding
ARM: KVM: promote vfp_host pointer to generic host cpu context
ARM: KVM: add architecture specific hook for capabilities
ARM: KVM: perform HYP initilization for hotplugged CPUs
ARM: KVM: switch to a dual-step HYP init code
ARM: KVM: rework HYP page table freeing
ARM: KVM: enforce maximum size for identity mapped code
ARM: KVM: move to a KVM provided HYP idmap
...
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlights this time around are:
- A pile of addition POWER8 bits and nits, such as updated
performance counter support (Michael Ellerman), new branch history
buffer support (Anshuman Khandual), base support for the new PCI
host bridge when not using the hypervisor (Gavin Shan) and other
random related bits and fixes from various contributors.
- Some rework of our page table format by Aneesh Kumar which fixes a
thing or two and paves the way for THP support. THP itself will
not make it this time around however.
- More Freescale updates, including Altivec support on the new e6500
cores, new PCI controller support, and a pile of new boards support
and updates.
- The usual batch of trivial cleanups & fixes"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
powerpc: Fix build error for book3e
powerpc: Context switch the new EBB SPRs
powerpc: Turn on the EBB H/FSCR bits
powerpc: Replace CPU_FTR_BCTAR with CPU_FTR_ARCH_207S
powerpc: Setup BHRB instructions facility in HFSCR for POWER8
powerpc: Fix interrupt range check on debug exception
powerpc: Update tlbie/tlbiel as per ISA doc
powerpc: Print page size info during boot
powerpc: print both base and actual page size on hash failure
powerpc: Fix hpte_decode to use the correct decoding for page sizes
powerpc: Decode the pte-lp-encoding bits correctly.
powerpc: Use encode avpn where we need only avpn values
powerpc: Reduce PTE table memory wastage
powerpc: Move the pte free routines from common header
powerpc: Reduce the PTE_INDEX_SIZE
powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format
powerpc: New hugepage directory format
powerpc: Don't truncate pgd_index wrongly
powerpc: Don't hard code the size of pte page
powerpc: Save DAR and DSISR in pt_regs on MCE
...
This adds the API for userspace to instantiate an XICS device in a VM
and connect VCPUs to it. The API consists of a new device type for
the KVM_CREATE_DEVICE ioctl, a new capability KVM_CAP_IRQ_XICS, which
functions similarly to KVM_CAP_IRQ_MPIC, and the KVM_IRQ_LINE ioctl,
which is used to assert and deassert interrupt inputs of the XICS.
The XICS device has one attribute group, KVM_DEV_XICS_GRP_SOURCES.
Each attribute within this group corresponds to the state of one
interrupt source. The attribute number is the same as the interrupt
source number.
This does not support irq routing or irqfd yet.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add the missing unlock before return from function set_base_addr()
when disables the mapping.
Introduced by commit 5df554ad5b
(kvm/ppc/mpic: in-kernel MPIC emulation)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alexander Graf <agraf@suse.de>
These functions do an srcu_dereference without acquiring the srcu lock
themselves.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is an unused (no pun intended) leftover from when this code did
reference counting.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Keeping a linked list of statically defined objects doesn't work
very well when we have multiple guests. :-P
Switch to an array of constant objects. This fixes a hang when
multiple guests are used.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: remove struct list_head from mem_reg]
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
We look at both the segment base page size and actual page size and store
the pte-lp-encodings in an array per base page size.
We also update all relevant functions to take actual page size argument
so that we can use the correct PTE LP encoding in HPTE. This should also
get the basic Multiple Page Size per Segment (MPSS) support. This is needed
to enable THP on ppc64.
[Fixed PR KVM build --BenH]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the ability for userspace to save and restore the state
of the XICS interrupt presentation controllers (ICPs) via the
KVM_GET/SET_ONE_REG interface. Since there is one ICP per vcpu, we
simply define a new 64-bit register in the ONE_REG space for the ICP
state. The state includes the CPU priority setting, the pending IPI
priority, and the priority and source number of any pending external
interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for the ibm,int-on and ibm,int-off RTAS calls to the
in-kernel XICS emulation and corrects the handling of the saved
priority by the ibm,set-xive RTAS call. With this, ibm,int-off sets
the specified interrupt's priority in its saved_priority field and
sets the priority to 0xff (the least favoured value). ibm,int-on
restores the saved_priority to the priority field, and ibm,set-xive
sets both the priority and the saved_priority to the specified
priority value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This streamlines our handling of external interrupts that come in
while we're in the guest. First, when waking up a hardware thread
that was napping, we split off the "napping due to H_CEDE" case
earlier, and use the code that handles an external interrupt (0x500)
in the guest to handle that too. Secondly, the code that handles
those external interrupts now checks if any other thread is exiting
to the host before bouncing an external interrupt to the guest, and
also checks that there is actually an external interrupt pending for
the guest before setting the LPCR MER bit (mediated external request).
This also makes sure that we clear the "ceded" flag when we handle a
wakeup from cede in real mode, and fixes a potential infinite loop
in kvmppc_run_vcpu() which can occur if we ever end up with the ceded
flag set but MSR[EE] off.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds an implementation of the XICS hypercalls in real mode for HV
KVM, which allows us to avoid exiting the guest MMU context on all
threads for a variety of operations such as fetching a pending
interrupt, EOI of messages, IPIs, etc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, we wake up a CPU by sending a host IPI with
smp_send_reschedule() to thread 0 of that core, which will take all
threads out of the guest, and cause them to re-evaluate their
interrupt status on the way back in.
This adds a mechanism to differentiate real host IPIs from IPIs sent
by KVM for guest threads to poke each other, in order to target the
guest threads precisely when possible and avoid that global switch of
the core to host state.
We then use this new facility in the in-kernel XICS code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds in-kernel emulation of the XICS (eXternal Interrupt
Controller Specification) interrupt controller specified by PAPR, for
both HV and PR KVM guests.
The XICS emulation supports up to 1048560 interrupt sources.
Interrupt source numbers below 16 are reserved; 0 is used to mean no
interrupt and 2 is used for IPIs. Internally these are represented in
blocks of 1024, called ICS (interrupt controller source) entities, but
that is not visible to userspace.
Each vcpu gets one ICP (interrupt controller presentation) entity,
used to store the per-vcpu state such as vcpu priority, pending
interrupt state, IPI request, etc.
This does not include any API or any way to connect vcpus to their
ICP state; that will be added in later patches.
This is based on an initial implementation by Michael Ellerman
<michael@ellerman.id.au> reworked by Benjamin Herrenschmidt and
Paul Mackerras.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix typo, add dependency on !KVM_MPIC]
Signed-off-by: Alexander Graf <agraf@suse.de>
For pseries machine emulation, in order to move the interrupt
controller code to the kernel, we need to intercept some RTAS
calls in the kernel itself. This adds an infrastructure to allow
in-kernel handlers to be registered for RTAS services by name.
A new ioctl, KVM_PPC_RTAS_DEFINE_TOKEN, then allows userspace to
associate token values with those service names. Then, when the
guest requests an RTAS service with one of those token values, it
will be handled by the relevant in-kernel handler rather than being
passed up to userspace as at present.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix warning]
Signed-off-by: Alexander Graf <agraf@suse.de>
We no longer need to keep track of this now that MPIC destruction
always happens either during VM destruction (after MMIO has been
destroyed) or during a failed creation (before the fd has been exposed
to userspace, and thus before the MMIO region could have been
registered).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The hassle of getting refcounting right was greater than the hassle
of keeping a list of devices to destroy on VM exit.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code as is doesn't make any sense on non-e500 platforms. Restrict it
there, so that people don't get wrong ideas on what would actually work.
This patch should get reverted as soon as it's possible to either run e500
guests on non-e500 hosts or the MPIC emulation gains support for non-e500
modes.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that all pieces are in place for reusing generic irq infrastructure,
we can copy x86's implementation of KVM_IRQ_LINE irq injection and simply
reuse it for PPC, as it will work there just as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that all the irq routing and irqfd pieces are generic, we can expose
real irqchip support to all of KVM's internal helpers.
This allows us to use irqfd with the in-kernel MPIC.
Signed-off-by: Alexander Graf <agraf@suse.de>
Enabling this capability connects the vcpu to the designated in-kernel
MPIC. Using explicit connections between vcpus and irqchips allows
for flexibility, but the main benefit at the moment is that it
simplifies the code -- KVM doesn't need vm-global state to remember
which MPIC object is associated with this vm, and it doesn't need to
care about ordering between irqchip creation and vcpu creation.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: add stub functions for kvmppc_mpic_{dis,}connect_vcpu]
Signed-off-by: Alexander Graf <agraf@suse.de>
Hook the MPIC code up to the KVM interfaces, add locking, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: add stub function for kvmppc_mpic_set_epr, non-booke, 64bit]
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove braces that Linux style doesn't permit, remove space after
'*' that Lindent added, keep error/debug strings contiguous, etc.
Substitute type names, debug prints, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove some parts of the code that are obviously QEMU or Raven specific
before fixing style issues, to reduce the style issues that need to be
fixed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is QEMU's hw/openpic.c from commit
abd8d4a4d6dfea7ddea72f095f993e1de941614e ("Update version for
1.4.0-rc0"), run through Lindent with no other changes to ease merging
future changes between Linux and QEMU. Remaining style issues
(including those introduced by Lindent) will be fixed in a later patch.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present, the KVM_GET_DIRTY_LOG ioctl doesn't report modifications
done by the host to the virtual processor areas (VPAs) and dispatch
trace logs (DTLs) registered by the guest. This is because those
modifications are done either in real mode or in the host kernel
context, and in neither case does the access go through the guest's
HPT, and thus no change (C) bit gets set in the guest's HPT.
However, the changes done by the host do need to be tracked so that
the modified pages get transferred when doing live migration. In
order to track these modifications, this adds a dirty flag to the
struct representing the VPA/DTL areas, and arranges to set the flag
when the VPA/DTL gets modified by the host. Then, when we are
collecting the dirty log, we also check the dirty flags for the
VPA and DTL for each vcpu and set the relevant bit in the dirty log
if necessary. Doing this also means we now need to keep track of
the guest physical address of the VPA/DTL areas.
So as not to lose track of modifications to a VPA/DTL area when it gets
unregistered, or when a new area gets registered in its place, we need
to transfer the dirty state to the rmap chain. This adds code to
kvmppc_unpin_guest_page() to do that if the area was dirty. To simplify
that code, we now require that all VPA, DTL and SLB shadow buffer areas
fit within a single host page. Guests already comply with this
requirement because pHyp requires that these areas not cross a 4k
boundary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present, the code that determines whether a HPT entry has changed,
and thus needs to be sent to userspace when it is copying the HPT,
doesn't consider a hardware update to the reference and change bits
(R and C) in the HPT entries to constitute a change that needs to
be sent to userspace. This adds code to check for changes in R and C
when we are scanning the HPT to find changed entries, and adds code
to set the changed flag for the HPTE when we update the R and C bits
in the guest view of the HPTE.
Since we now need to set the HPTE changed flag in book3s_64_mmu_hv.c
as well as book3s_hv_rm_mmu.c, we move the note_hpte_modification()
function into kvm_book3s_64.h.
Current Linux guest kernels don't use the hardware updates of R and C
in the HPT, so this change won't affect them. Linux (or other) kernels
might in future want to use the R and C bits and have them correctly
transferred across when a guest is migrated, so it is better to correct
this deficiency.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Extend processor compatibility names to e6500 cores.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Embedded.Page Table (E.PT) category is not supported yet in e6500 kernel.
Configure TLBnCFG to remove E.PT and E.HV.LRAT categories from VCPUs.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
EPTCFG register defined by E.PT is accessed unconditionally by Linux guests
in the presence of MAV 2.0. Emulate it now.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for TLBnPS registers available in MMU Architecture Version
(MAV) 2.0.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Vcpu's MMU default configuration and geometry update logic was buried in
a chunk of code. Move them to dedicated functions to add more clarity.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
MMU registers were exposed to user-space using sregs interface. Add them
to ONE_REG interface using kvmppc_get_one_reg/kvmppc_set_one_reg delegation
mechanism.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor Book3E ONE_REG ioctl implementation to use kvmppc_get_one_reg/
kvmppc_set_one_reg delegation interface introduced by Book3S. This is
necessary for MMU SPRs which are platform specifics.
Get rid of useless case braces in the process.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows the exit to user space if emulator request by returning
EMULATE_EXIT_USER. This will be used in subsequent patches in list
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the instruction emulator code returns EMULATE_EXIT_USER
and common code initializes the "run->exit_reason = .." and
"vcpu->arch.hcall_needed = .." with one fixed reason.
But there can be different reasons when emulator need to exit
to user space. To support that the "run->exit_reason = .."
and "vcpu->arch.hcall_needed = .." initialization is moved a
level up to emulator.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Instruction emulation return EMULATE_DO_PAPR when it requires
exit to userspace on book3s. Similar return is required
for booke. EMULATE_DO_PAPR reads out to be confusing so it is
renamed to EMULATE_EXIT_USER.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch defines the interface parameter for KVM_SET_GUEST_DEBUG
ioctl support. Follow up patches will use this for setting up
hardware breakpoints, watchpoints and software breakpoints.
Also kvm_arch_vcpu_ioctl_set_guest_debug() is brought one level below.
This is because I am not sure what is required for book3s. So this ioctl
behaviour will not change for book3s.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes these errors when building UP with CONFIG_KVM_BOOK3S_64_HV=y:
arch/powerpc/kvm/book3s_hv.c:1855:2: error: implicit declaration of function 'inhibit_secondary_onlining' [-Werror=implicit-function-declaration]
arch/powerpc/kvm/book3s_hv.c:1862:2: error: implicit declaration of function 'uninhibit_secondary_onlining' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
and this error (with CONFIG_KVM_BOOK3S_64=m, or a vmlinux link error
with CONFIG_KVM_BOOK3S_64=y):
ERROR: "smp_send_reschedule" [arch/powerpc/kvm/kvm.ko] undefined!
make[2]: *** [__modpost] Error 1
The fix for the link error is suboptimal; ideally we want a self_ipi()
function from irq.c, connected at least to the MPIC code, to initiate
an IPI to this cpu. The fix here at least lets the code build, and it
will work, just with interrupts being delayed sometimes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
complete_mmio_load writes back the mmio result into the
destination register. Doing this on a store results in
register corruption.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the one_reg interface to get the special instruction
to be used for setting software breakpoint from userspace.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 523f0e5421 ("KVM: PPC: E500:
Explicitly mark shadow maps invalid") began using E500_TLB_VALID
for guest TLB1 entries, and skipping invalidations if it's not set.
However, when E500_TLB_VALID was set for such entries, it was on a
fake local ref, and so the invalidations never happen. gtlb_privs
is documented as being only for guest TLB0, though we already violate
that with E500_TLB_BITMAP.
Now that we have MMU notifiers, and thus don't need to actually
retain a reference to the mapped pages, get rid of tlb_refs, and
use gtlb_privs for E500_TLB_VALID in TLB1.
Since we can have more than one host TLB entry for a given tlbe_ref,
be careful not to clear existing flags that are relevant to other
host TLB entries when preparing a new host TLB entry.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
It's possible that we're using the same host TLB1 slot to map (a
presumably different portion of) the same guest TLB1 entry. Clear
the bit in the map before setting it, so that if the esels are the same
the bit will remain set.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add one to esel values in h2g_tlb1_rmap, so that "no mapping" can be
distinguished from "esel 0". Note that we're not saved by the fact
that host esel 0 is reserved for non-KVM use, because KVM host esel
numbering is not the raw host numbering (see to_htlb1_esel).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The existing check handles the case where we've migrated to a different
core than we last ran on, but it doesn't handle the case where we're
still on the same cpu we last ran on, but some other vcpu has run on
this cpu in the meantime.
Without this, guest segfaults (and other misbehavior) have been seen in
smp guests.
Cc: stable@vger.kernel.org # 3.8.x
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently kvmppc_core_dequeue_external() takes a struct kvm_interrupt *
argument and does nothing with it, in any of its implementations.
This removes it in order to make things easier for forthcoming
in-kernel interrupt controller emulation code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 523f0e5421 ("KVM: PPC: E500:
Explicitly mark shadow maps invalid") began using E500_TLB_VALID
for guest TLB1 entries, and skipping invalidations if it's not set.
However, when E500_TLB_VALID was set for such entries, it was on a
fake local ref, and so the invalidations never happen. gtlb_privs
is documented as being only for guest TLB0, though we already violate
that with E500_TLB_BITMAP.
Now that we have MMU notifiers, and thus don't need to actually
retain a reference to the mapped pages, get rid of tlb_refs, and
use gtlb_privs for E500_TLB_VALID in TLB1.
Since we can have more than one host TLB entry for a given tlbe_ref,
be careful not to clear existing flags that are relevant to other
host TLB entries when preparing a new host TLB entry.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
It's possible that we're using the same host TLB1 slot to map (a
presumably different portion of) the same guest TLB1 entry. Clear
the bit in the map before setting it, so that if the esels are the same
the bit will remain set.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add one to esel values in h2g_tlb1_rmap, so that "no mapping" can be
distinguished from "esel 0". Note that we're not saved by the fact
that host esel 0 is reserved for non-KVM use, because KVM host esel
numbering is not the raw host numbering (see to_htlb1_esel).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Installed debug handler will be used for guest debug support
and debug facility emulation features (patches for these
features will follow this patch).
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[bharat.bhushan@freescale.com: Substantial changes]
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
If userspace wants to change some specific bits of TSR
(timer status register) then it uses GET/SET_SREGS ioctl interface.
So the steps will be:
i) user-space will make get ioctl,
ii) change TSR in userspace
iii) then make set ioctl.
It can happen that TSR gets changed by kernel after step i) and
before step iii).
To avoid this we have added below one_reg ioctls for oring and clearing
specific bits in TSR. This patch adds one registerface for:
1) setting specific bit in TSR (timer status register)
2) clearing specific bit in TSR (timer status register)
3) setting/getting the TCR register. There are cases where we want to only
change TCR and not TSR. Although we can uses SREGS without
KVM_SREGS_E_UPDATE_TSR flag but I think one reg is better. I am open
if someone feels we should use SREGS only here.
4) getting/setting TSR register
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is done so that same function can be called from SREGS and
ONE_REG interface (follow up patch).
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Merge reason:
From: Alexander Graf <agraf@suse.de>
"Just recently this really important patch got pulled into Linus' tree for 3.9:
commit 1674400aae
Author: Anton Blanchard <anton <at> samba.org>
Date: Tue Mar 12 01:51:51 2013 +0000
Without that commit, I can not boot my G5, thus I can't run automated tests on it against my queue.
Could you please merge kvm/next against linus/master, so that I can base my trees against that?"
* upstream/master: (653 commits)
PCI: Use ROM images from firmware only if no other ROM source available
sparc: remove unused "config BITS"
sparc: delete "if !ULTRA_HAS_POPULATION_COUNT"
KVM: Fix bounds checking in ioapic indirect register reads (CVE-2013-1798)
KVM: x86: Convert MSR_KVM_SYSTEM_TIME to use gfn_to_hva_cache functions (CVE-2013-1797)
KVM: x86: fix for buffer overflow in handling of MSR_KVM_SYSTEM_TIME (CVE-2013-1796)
arm64: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
arm64: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
sgy-cts1000: Remove __dev* attributes
KVM: x86: fix deadlock in clock-in-progress request handling
KVM: allow host header to be included even for !CONFIG_KVM
hwmon: (lm75) Fix tcn75 prefix
hwmon: (lm75.h) Update header inclusion
MAINTAINERS: Remove Mark M. Hoffman
xfs: ensure we capture IO errors correctly
xfs: fix xfs_iomap_eof_prealloc_initial_size type
...
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Now we use ESID_BITS of kernel address to build proto vsid. So rename
USER_ESIT_BITS to ESID_BITS
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.8]
This patch makes the parameter old a const pointer to the old memory
slot and adds a new parameter named change to know the change being
requested: the former is for removing extra copying and the latter is
for cleaning up the code.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch drops the parameter old, a copy of the old memory slot, and
adds a new parameter named change to know the change being requested.
This not only cleans up the code but also removes extra copying of the
memory slot structure.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
X86 does not use this any more. The remaining user, s390's !user_alloc
check, can be simply removed since KVM_SET_MEMORY_REGION ioctl is no
longer supported.
Note: fixed powerpc's indentations with spaces to suppress checkpatch
errors.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff90702: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
Commit a413f474a0 ("powerpc: Disable relocation on exceptions whenever
PR KVM is active") added calls to pSeries_disable_reloc_on_exc() and
pSeries_enable_reloc_on_exc() to book3s_pr.c, and added declarations
of those functions to <asm/hvcall.h>, but didn't add an include of
<asm/hvcall.h> to book3s_pr.c. 64-bit kernels seem to get hvcall.h
included via some other path, but 32-bit kernels fail to compile with:
arch/powerpc/kvm/book3s_pr.c: In function ‘kvmppc_core_init_vm’:
arch/powerpc/kvm/book3s_pr.c:1300:4: error: implicit declaration of function ‘pSeries_disable_reloc_on_exc’ [-Werror=implicit-function-declaration]
arch/powerpc/kvm/book3s_pr.c: In function ‘kvmppc_core_destroy_vm’:
arch/powerpc/kvm/book3s_pr.c:1316:4: error: implicit declaration of function ‘pSeries_enable_reloc_on_exc’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[2]: *** [arch/powerpc/kvm/book3s_pr.o] Error 1
make[1]: *** [arch/powerpc/kvm] Error 2
make: *** [sub-make] Error 2
This fixes it by adding an include of hvcall.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The CFAR (Come-From Address Register) is a useful debugging aid that
exists on POWER7 processors. Currently HV KVM doesn't save or restore
the CFAR register for guest vcpus, making the CFAR of limited use in
guests.
This adds the necessary code to capture the CFAR value saved in the
early exception entry code (it has to be saved before any branch is
executed), save it in the vcpu.arch struct, and restore it on entry
to the guest.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the guest triggers an alignment interrupt, we don't handle it properly
today and instead BUG_ON(). This really shouldn't happen.
Instead, we should just pass the interrupt back into the guest so it can deal
with it.
Reported-by: Gao Guanhua-B22826 <B22826@freescale.com>
Tested-by: Gao Guanhua-B22826 <B22826@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Current kvmppc_booke_handlers uses the same macro (KVM_HANDLER) and
all handlers are considered to be the same size. This will not be
the case if we want to use different macros for different handlers.
This patch improves the kvmppc_booke_handler so that it can
support different macros for different handlers.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[bharat.bhushan@freescale.com: Substantial changes]
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Like other places, use thread_struct to get vcpu reference.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The guest TLB handling code should not have any insight into how the host
TLB shadow code works.
kvmppc_e500_tlbil_all() is a function that is used for distinction between
e500v2 and e500mc (E.HV) on how to flush shadow entries. This function really
is private between the e500.c/e500mc.c file and e500_mmu_host.c.
Instead of this one, use the public kvmppc_core_flush_tlb() function to flush
all shadow TLB entries. As a nice side effect, with this we also end up
flushing TLB1 entries which we forgot to do before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Host shadow TLB flushing is logic that the guest TLB code should have
no insight about. Declare the internal clear_tlb_refs and clear_tlb1_bitmap
functions static to the host TLB handling file.
Instead of these, we can use the already exported kvmppc_core_flush_tlb().
This gives us a common API across the board to say "please flush any
pending host shadow translation".
Signed-off-by: Alexander Graf <agraf@suse.de>
When a host mapping fault happens in a guest TLB1 entry today, we
map the translated guest entry into the host's TLB1.
This isn't particularly clever when the guest is mapped by normal 4k
pages, since these would be a lot better to put into TLB0 instead.
This patch adds the required logic to map 4k TLB1 shadow maps into
the host's TLB0.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch splits the file e500_tlb.c into e500_mmu.c (guest TLB handling)
and e500_mmu_host.c (host TLB handling).
The main benefit of this split is readability and maintainability. It's
just a lot harder to write dirty code :).
Signed-off-by: Alexander Graf <agraf@suse.de>
When emulating tlbwe, we want to automatically map the entry that just got
written in our shadow TLB map, because chances are quite high that it's
going to be used very soon.
Today this happens explicitly, duplicating all the logic that is in
kvmppc_mmu_map() already. Just call that one instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
When shadow mapping a page, mapping this page can fail. In that case we
don't have a shadow map.
Take this case into account, otherwise we might end up writing bogus TLB
entries into the host TLB.
While at it, also move the write_stlbe() calls into the respective TLBn
handlers.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we invalidate shadow TLB maps on the host, we don't mark them
as not valid. But we should.
Fix this by removing the E500_TLB_VALID from their flags when
invalidating.
Signed-off-by: Alexander Graf <agraf@suse.de>
Later patches want to call the function and it doesn't have
dependencies on anything below write_host_tlbe.
Move it higher up in the file.
Signed-off-by: Alexander Graf <agraf@suse.de>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Alexander Graf <agraf@suse.de>
CC: Avi Kivity <avi@redhat.com>
CC: Marcelo Tosatti <mtosatti@redhat.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guests can trigger MMIO exits using dcbf. Since we don't emulate cache
incoherent MMIO, just do nothing and move on.
Reported-by: Ben Collins <ben.c@servergy.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Ben Collins <ben.c@servergy.com>
CC: stable@vger.kernel.org
We need to be able to read and write the contents of the EPR register
from user space.
This patch implements that logic through the ONE_REG API and declares
its (never implemented) SREGS counterpart as deprecated.
Signed-off-by: Alexander Graf <agraf@suse.de>
The External Proxy Facility in FSL BookE chips allows the interrupt
controller to automatically acknowledge an interrupt as soon as a
core gets its pending external interrupt delivered.
Today, user space implements the interrupt controller, so we need to
check on it during such a cycle.
This patch implements logic for user space to enable EPR exiting,
disable EPR exiting and EPR exiting itself, so that user space can
acknowledge an interrupt when an external interrupt has successfully
been delivered into the guest vcpu.
Signed-off-by: Alexander Graf <agraf@suse.de>
The EPR register is potentially valid for PR KVM as well, so we need
to emulate accesses to it. It's only defined for reading, so only
handle the mfspr case.
Signed-off-by: Alexander Graf <agraf@suse.de>
When injecting an interrupt into guest context, we usually don't need
to check for requests anymore. At least not until today.
With the introduction of EPR, we will have to create a request when the
guest has successfully accepted an external interrupt though.
So we need to prepare the interrupt delivery to abort guest entry
gracefully. Otherwise we'd delay the EPR request.
Signed-off-by: Alexander Graf <agraf@suse.de>
On mfspr/mtspr emulation path Book3E's MMUCFG SPR with value 1015 clashes
with G4's MSSSR0 SPR. Move MSSSR0 emulation from generic part to Books3S.
MSSSR0 also clashes with Book3S's DABRX SPR. DABRX was not explicitly
handled so Book3S execution flow will behave as before.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running on top of pHyp, the hypercall instruction "sc 1" goes
straight into pHyp without trapping in supervisor mode.
So if we want to support PAPR guest in this configuration we need to
add a second way of accessing PAPR hypercalls, preferably with the
exact same semantics except for the instruction.
So let's overlay an officially reserved instruction and emulate PAPR
hypercalls whenever we hit that one.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we hit an emulation result that we didn't expect, that is an error,
but it's nothing that warrants a BUG(), because it can be guest triggered.
So instead, let's only WARN() the user that this happened.
Signed-off-by: Alexander Graf <agraf@suse.de>
For PR KVM we allow userspace to map 0xc000000000000000. Because
transitioning from userspace to the guest kernel may use the relocated
exception vectors we have to disable relocation on exceptions whenever
PR KVM is active as we cannot trust that address.
This issue does not apply to HV KVM, since changing from a guest to the
hypervisor will never use the relocated exception vectors.
Currently the hypervisor interface only allows us to toggle relocation
on exceptions on a partition wide scope, so we need to globally disable
relocation on exceptions when the first PR KVM instance is started and
only re-enable them when all PR KVM instances have been destroyed.
It's a bit heavy handed, but until the hypervisor gives us a lightweight
way to toggle relocation on exceptions on a single thread it's only real
option.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes this build breakage:
arch/powerpc/kvm/book3s_hv_ras.c: In function ‘kvmppc_realmode_mc_power7’:
arch/powerpc/kvm/book3s_hv_ras.c:126:23: error: ‘struct paca_struct’ has no member named ‘opal_mc_evt’
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There's no need for this to be an int, it holds a boolean.
Move to the end of the struct for alignment.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
It's easy to confuse KVM_MEMORY_SLOTS and KVM_MEM_SLOTS_NUM. One is
the user accessible slots and the other is user + private. Make this
more obvious.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Implement ONE_REG interface for EPCR register adding KVM_REG_PPC_EPCR to
the list of ONE_REG PPC supported registers.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency, use get/put_user]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add EPCR support in booke mtspr/mfspr emulation. EPCR register is defined only
for 64-bit and HV categories, we will expose it at this point only to 64-bit
virtual processors running on 64-bit HV hosts.
Define a reusable setter function for vcpu's EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: move HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
When delivering guest IRQs, update MSR computation mode according to guest
interrupt computation mode found in EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
Extend MAS2 EPN mask to retain most significant bits on 64-bit hosts.
Use this mask in tlb effective address accessor.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Mask high 32 bits of MAS2's effective page number in tlbwe emulation for guests
running in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add emulation helper for getting instruction ea and refactor tlb instruction
emulation to use it.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: keep rt variable around]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add interrupt handling support for 64-bit bookehv hosts. Unify 32 and 64 bit
implementations using a common stack layout and a common execution flow starting
from kvm_handler_common macro. Update documentation for 64-bit input register
values. This patch only address the bolted TLB miss exception handlers version.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
GET_VCPU define will not be implemented for 64-bit for performance reasons
so get rid of it also on 32-bit.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
64-bit GCC 4.5.1 warns about an uninitialized variable which was guarded
by a flag. Initialize the variable to make it happy.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: reword comment]
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, if a machine check interrupt happens while we are in the
guest, we exit the guest and call the host's machine check handler,
which tends to cause the host to panic. Some machine checks can be
triggered by the guest; for example, if the guest creates two entries
in the SLB that map the same effective address, and then accesses that
effective address, the CPU will take a machine check interrupt.
To handle this better, when a machine check happens inside the guest,
we call a new function, kvmppc_realmode_machine_check(), while still in
real mode before exiting the guest. On POWER7, it handles the cases
that the guest can trigger, either by flushing and reloading the SLB,
or by flushing the TLB, and then it delivers the machine check interrupt
directly to the guest without going back to the host. On POWER7, the
OPAL firmware patches the machine check interrupt vector so that it
gets control first, and it leaves behind its analysis of the situation
in a structure pointed to by the opal_mc_evt field of the paca. The
kvmppc_realmode_machine_check() function looks at this, and if OPAL
reports that there was no error, or that it has handled the error, we
also go straight back to the guest with a machine check. We have to
deliver a machine check to the guest since the machine check interrupt
might have trashed valid values in SRR0/1.
If the machine check is one we can't handle in real mode, and one that
OPAL hasn't already handled, or on PPC970, we exit the guest and call
the host's machine check handler. We do this by jumping to the
machine_check_fwnmi label, rather than absolute address 0x200, because
we don't want to re-execute OPAL's handler on POWER7. On PPC970, the
two are equivalent because address 0x200 just contains a branch.
Then, if the host machine check handler decides that the system can
continue executing, kvmppc_handle_exit() delivers a machine check
interrupt to the guest -- once again to let the guest know that SRR0/1
have been modified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix checkpatch warnings]
Signed-off-by: Alexander Graf <agraf@suse.de>
When we change or remove a HPT (hashed page table) entry, we can do
either a global TLB invalidation (tlbie) that works across the whole
machine, or a local invalidation (tlbiel) that only affects this core.
Currently we do local invalidations if the VM has only one vcpu or if
the guest requests it with the H_LOCAL flag, though the guest Linux
kernel currently doesn't ever use H_LOCAL. Then, to cope with the
possibility that vcpus moving around to different physical cores might
expose stale TLB entries, there is some code in kvmppc_hv_entry to
flush the whole TLB of entries for this VM if either this vcpu is now
running on a different physical core from where it last ran, or if this
physical core last ran a different vcpu.
There are a number of problems on POWER7 with this as it stands:
- The TLB invalidation is done per thread, whereas it only needs to be
done per core, since the TLB is shared between the threads.
- With the possibility of the host paging out guest pages, the use of
H_LOCAL by an SMP guest is dangerous since the guest could possibly
retain and use a stale TLB entry pointing to a page that had been
removed from the guest.
- The TLB invalidations that we do when a vcpu moves from one physical
core to another are unnecessary in the case of an SMP guest that isn't
using H_LOCAL.
- The optimization of using local invalidations rather than global should
apply to guests with one virtual core, not just one vcpu.
(None of this applies on PPC970, since there we always have to
invalidate the whole TLB when entering and leaving the guest, and we
can't support paging out guest memory.)
To fix these problems and simplify the code, we now maintain a simple
cpumask of which cpus need to flush the TLB on entry to the guest.
(This is indexed by cpu, though we only ever use the bits for thread
0 of each core.) Whenever we do a local TLB invalidation, we set the
bits for every cpu except the bit for thread 0 of the core that we're
currently running on. Whenever we enter a guest, we test and clear the
bit for our core, and flush the TLB if it was set.
On initial startup of the VM, and when resetting the HPT, we set all the
bits in the need_tlb_flush cpumask, since any core could potentially have
stale TLB entries from the previous VM to use the same LPID, or the
previous contents of the HPT.
Then, we maintain a count of the number of online virtual cores, and use
that when deciding whether to use a local invalidation rather than the
number of online vcpus. The code to make that decision is extracted out
into a new function, global_invalidates(). For multi-core guests on
POWER7 (i.e. when we are using mmu notifiers), we now never do local
invalidations regardless of the H_LOCAL flag.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The mask of MSR bits that get transferred from the guest MSR to the
shadow MSR included MSR_DE. In fact that bit only exists on Book 3E
processors, and it is assigned the same bit used for MSR_BE on Book 3S
processors. Since we already had MSR_BE in the mask, this just removes
MSR_DE.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes various issues in how we were handling the VSX registers
that exist on POWER7 machines. First, we were running off the end
of the current->thread.fpr[] array. Ultimately this was because the
vcpu->arch.vsr[] array is sized to be able to store both the FP
registers and the extra VSX registers (i.e. 64 entries), but PR KVM
only uses it for the extra VSX registers (i.e. 32 entries).
Secondly, calling load_up_vsx() from C code is a really bad idea,
because it jumps to fast_exception_return at the end, rather than
returning with a blr instruction. This was causing it to jump off
to a random location with random register contents, since it was using
the largely uninitialized stack frame created by kvmppc_load_up_vsx.
In fact, it isn't necessary to call either __giveup_vsx or load_up_vsx,
since giveup_fpu and load_up_fpu handle the extra VSX registers as well
as the standard FP registers on machines with VSX. Also, since VSX
instructions can access the VMX registers and the FP registers as well
as the extra VSX registers, we have to load up the FP and VMX registers
before we can turn on the MSR_VSX bit for the guest. Conversely, if
we save away any of the VSX or FP registers, we have to turn off MSR_VSX
for the guest.
To handle all this, it is more convenient for a single call to
kvmppc_giveup_ext() to handle all the state saving that needs to be done,
so we make it take a set of MSR bits rather than just one, and the switch
statement becomes a series of if statements. Similarly kvmppc_handle_ext
needs to be able to load up more than one set of registers.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds basic emulation of the PURR and SPURR registers. We assume
we are emulating a single-threaded core, so these advance at the same
rate as the timebase. A Linux kernel running on a POWER7 expects to
be able to access these registers and is not prepared to handle a
program interrupt on accessing them.
This also adds a very minimal emulation of the DSCR (data stream
control register). Writes are ignored and reads return zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, if the guest does an H_PROTECT hcall requesting that the
permissions on a HPT entry be changed to allow writing, we make the
requested change even if the page is marked read-only in the host
Linux page tables. This is a problem since it would for instance
allow a guest to modify a page that KSM has decided can be shared
between multiple guests.
To fix this, if the new permissions for the page allow writing, we need
to look up the memslot for the page, work out the host virtual address,
and look up the Linux page tables to get the PTE for the page. If that
PTE is read-only, we reduce the HPTE permissions to read-only.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes a bug in the code which allows userspace to read out the
contents of the guest's hashed page table (HPT). On the second and
subsequent passes through the HPT, when we are reporting only those
entries that have changed, we were incorrectly initializing the index
field of the header with the index of the first entry we skipped
rather than the first changed entry. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
With HV-style KVM, we maintain reverse-mapping lists that enable us to
find all the HPT (hashed page table) entries that reference each guest
physical page, with the heads of the lists in the memslot->arch.rmap
arrays. When we reset the HPT (i.e. when we reboot the VM), we clear
out all the HPT entries but we were not clearing out the reverse
mapping lists. The result is that as we create new HPT entries, the
lists get corrupted, which can easily lead to loops, resulting in the
host kernel hanging when it tries to traverse those lists.
This fixes the problem by zeroing out all the reverse mapping lists
when we zero out the HPT. This incidentally means that we are also
zeroing our record of the referenced and changed bits (not the bits
in the Linux PTEs, used by the Linux MM subsystem, but the bits used
by the KVM_GET_DIRTY_LOG ioctl, and those used by kvm_age_hva() and
kvm_test_age_hva()).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
A new ioctl, KVM_PPC_GET_HTAB_FD, returns a file descriptor. Reads on
this fd return the contents of the HPT (hashed page table), writes
create and/or remove entries in the HPT. There is a new capability,
KVM_CAP_PPC_HTAB_FD, to indicate the presence of the ioctl. The ioctl
takes an argument structure with the index of the first HPT entry to
read out and a set of flags. The flags indicate whether the user is
intending to read or write the HPT, and whether to return all entries
or only the "bolted" entries (those with the bolted bit, 0x10, set in
the first doubleword).
This is intended for use in implementing qemu's savevm/loadvm and for
live migration. Therefore, on reads, the first pass returns information
about all HPTEs (or all bolted HPTEs). When the first pass reaches the
end of the HPT, it returns from the read. Subsequent reads only return
information about HPTEs that have changed since they were last read.
A read that finds no changed HPTEs in the HPT following where the last
read finished will return 0 bytes.
The format of the data provides a simple run-length compression of the
invalid entries. Each block of data starts with a header that indicates
the index (position in the HPT, which is just an array), the number of
valid entries starting at that index (may be zero), and the number of
invalid entries following those valid entries. The valid entries, 16
bytes each, follow the header. The invalid entries are not explicitly
represented.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix documentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes a HPTE removal function, kvmppc_do_h_remove(), available
outside book3s_hv_rm_mmu.c. This will be used by the HPT writing
code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This uses a bit in our record of the guest view of the HPTE to record
when the HPTE gets modified. We use a reserved bit for this, and ensure
that this bit is always cleared in HPTE values returned to the guest.
The recording of modified HPTEs is only done if other code indicates
its interest by setting kvm->arch.hpte_mod_interest to a non-zero value.
The reason for this is that when later commits add facilities for
userspace to read the HPT, the first pass of reading the HPT will be
quicker if there are no (or very few) HPTEs marked as modified,
rather than having most HPTEs marked as modified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes a bug where adding a new guest HPT entry via the H_ENTER
hcall would lose the "changed" bit in the reverse map information
for the guest physical page being mapped. The result was that the
KVM_GET_DIRTY_LOG could return a zero bit for the page even though
the page had been modified by the guest.
This fixes it by only modifying the index and present bits in the
reverse map entry, thus preserving the reference and change bits.
We were also unnecessarily setting the reference bit, and this
fixes that too.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This restructures the code that creates HPT (hashed page table)
entries so that it can be called in situations where we don't have a
struct vcpu pointer, only a struct kvm pointer. It also fixes a bug
where kvmppc_map_vrma() would corrupt the guest R4 value.
Most of the work of kvmppc_virtmode_h_enter is now done by a new
function, kvmppc_virtmode_do_h_enter, which itself calls another new
function, kvmppc_do_h_enter, which contains most of the old
kvmppc_h_enter. The new kvmppc_do_h_enter takes explicit arguments
for the place to return the HPTE index, the Linux page tables to use,
and whether it is being called in real mode, thus removing the need
for it to have the vcpu as an argument.
Currently kvmppc_map_vrma creates the VRMA (virtual real mode area)
HPTEs by calling kvmppc_virtmode_h_enter, which is designed primarily
to handle H_ENTER hcalls from the guest that need to pin a page of
memory. Since H_ENTER returns the index of the created HPTE in R4,
kvmppc_virtmode_h_enter updates the guest R4, corrupting the guest R4
in the case when it gets called from kvmppc_map_vrma on the first
VCPU_RUN ioctl. With this, kvmppc_map_vrma instead calls
kvmppc_virtmode_do_h_enter with the address of a dummy word as the
place to store the HPTE index, thus avoiding corrupting the guest R4.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In order to support the generic eventfd infrastructure on PPC, we need
to call into the generic KVM in-kernel device mmio code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 55b665b026 ("KVM: PPC: Book3S HV: Provide a way for userspace
to get/set per-vCPU areas") includes a check on the length of the
dispatch trace log (DTL) to make sure the buffer is at least one entry
long. This is appropriate when registering a buffer, but the
interface also allows for any existing buffer to be unregistered by
specifying a zero address. In this case the length check is not
appropriate. This makes the check conditional on the address being
non-zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the code that accounts stolen time tends to overestimate the
stolen time, and will sometimes report more stolen time in a DTL
(dispatch trace log) entry than has elapsed since the last DTL entry.
This can cause guests to underflow the user or system time measured
for some tasks, leading to ridiculous CPU percentages and total runtimes
being reported by top and other utilities.
In addition, the current code was designed for the previous policy where
a vcore would only run when all the vcpus in it were runnable, and so
only counted stolen time on a per-vcore basis. Now that a vcore can
run while some of the vcpus in it are doing other things in the kernel
(e.g. handling a page fault), we need to count the time when a vcpu task
is preempted while it is not running as part of a vcore as stolen also.
To do this, we bring back the BUSY_IN_HOST vcpu state and extend the
vcpu_load/put functions to count preemption time while the vcpu is
in that state. Handling the transitions between the RUNNING and
BUSY_IN_HOST states requires checking and updating two variables
(accumulated time stolen and time last preempted), so we add a new
spinlock, vcpu->arch.tbacct_lock. This protects both the per-vcpu
stolen/preempt-time variables, and the per-vcore variables while this
vcpu is running the vcore.
Finally, we now don't count time spent in userspace as stolen time.
The task could be executing in userspace on behalf of the vcpu, or
it could be preempted, or the vcpu could be genuinely stopped. Since
we have no way of dividing up the time between these cases, we don't
count any of it as stolen.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the Book3S HV code implements a policy on multi-threaded
processors (i.e. POWER7) that requires all of the active vcpus in a
virtual core to be ready to run before we run the virtual core.
However, that causes problems on reset, because reset stops all vcpus
except vcpu 0, and can also reduce throughput since all four threads
in a virtual core have to wait whenever any one of them hits a
hypervisor page fault.
This relaxes the policy, allowing the virtual core to run as soon as
any vcpu in it is runnable. With this, the KVMPPC_VCPU_STOPPED state
and the KVMPPC_VCPU_BUSY_IN_HOST state have been combined into a single
KVMPPC_VCPU_NOTREADY state, since we no longer need to distinguish
between them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a thread in a virtual core becomes runnable while other threads
in the same virtual core are already running in the guest, it is
possible for the latecomer to join the others on the core without
first pulling them all out of the guest. Currently this only happens
rarely, when a vcpu is first started. This fixes some bugs and
omissions in the code in this case.
First, we need to check for VPA updates for the latecomer and make
a DTL entry for it. Secondly, if it comes along while the master
vcpu is doing a VPA update, we don't need to do anything since the
master will pick it up in kvmppc_run_core. To handle this correctly
we introduce a new vcore state, VCORE_STARTING. Thirdly, there is
a race because we currently clear the hardware thread's hwthread_req
before waiting to see it get to nap. A latecomer thread could have
its hwthread_req cleared before it gets to test it, and therefore
never increment the nap_count, leading to messages about wait_for_nap
timeouts.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There were a few places where we were traversing the list of runnable
threads in a virtual core, i.e. vc->runnable_threads, without holding
the vcore spinlock. This extends the places where we hold the vcore
spinlock to cover everywhere that we traverse that list.
Since we possibly need to sleep inside kvmppc_book3s_hv_page_fault,
this moves the call of it from kvmppc_handle_exit out to
kvmppc_vcpu_run, where we don't hold the vcore lock.
In kvmppc_vcore_blocked, we don't actually need to check whether
all vcpus are ceded and don't have any pending exceptions, since the
caller has already done that. The caller (kvmppc_run_vcpu) wasn't
actually checking for pending exceptions, so we add that.
The change of if to while in kvmppc_run_vcpu is to make sure that we
never call kvmppc_remove_runnable() when the vcore state is RUNNING or
EXITING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Subsequent patches implementing in-kernel XICS emulation will make it
possible for IPIs to arrive at secondary threads at arbitrary times.
This fixes some races in how we start the secondary threads, which
if not fixed could lead to occasional crashes of the host kernel.
This makes sure that (a) we have grabbed all the secondary threads,
and verified that they are no longer in the kernel, before we start
any thread, (b) that the secondary thread loads its vcpu pointer
after clearing the IPI that woke it up (so we don't miss a wakeup),
and (c) that the secondary thread clears its vcpu pointer before
incrementing the nap count. It also removes unnecessary setting
of the vcpu and vcore pointers in the paca in kvmppc_core_vcpu_load.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When a Book3S HV KVM guest is running, we need the host to be in
single-thread mode, that is, all of the cores (or at least all of
the cores where the KVM guest could run) to be running only one
active hardware thread. This is because of the hardware restriction
in POWER processors that all of the hardware threads in the core
must be in the same logical partition. Complying with this restriction
is much easier if, from the host kernel's point of view, only one
hardware thread is active.
This adds two hooks in the SMP hotplug code to allow the KVM code to
make sure that secondary threads (i.e. hardware threads other than
thread 0) cannot come online while any KVM guest exists. The KVM
code still has to check that any core where it runs a guest has the
secondary threads offline, but having done that check it can now be
sure that they will not come online while the guest is running.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The mtspr/mfspr emulation code became quite big over time. Move it
into its own function so things stay more readable.
Signed-off-by: Alexander Graf <agraf@suse.de>
When remembering the direction of a DCR transaction, we should write
to the same variable that we interpret on later when doing vcpu_run
again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Cc: stable@vger.kernel.org
This patch filters noslot pfn out from error pfns based on Marcelo comment:
noslot pfn is not a error pfn
After this patch,
- is_noslot_pfn indicates that the gfn is not in slot
- is_error_pfn indicates that the gfn is in slot but the error is occurred
when translate the gfn to pfn
- is_error_noslot_pfn indicates that the pfn either it is error pfns or it
is noslot pfn
And is_invalid_pfn can be removed, it makes the code more clean
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
arch/powerpc/include/asm/Kbuild
arch/powerpc/include/asm/kvm_para.h
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The mmu_notifier_retry is not specific to any vcpu (and never will be)
so only take struct kvm as a parameter.
The motivation is the ARM mmu code that needs to call this from
somewhere where we long let go of the vcpu pointer.
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix build failure for powerpc KVM by adding missing VPN_SHIFT definition
and the ';'
arch/powerpc/kvm/book3s_32_mmu_host.c: In function 'kvmppc_mmu_map_page':
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: 'VPN_SHIFT' undeclared (first use in this function)
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: (Each undeclared identifier is reported only once
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: for each function it appears in.)
arch/powerpc/kvm/book3s_32_mmu_host.c:178: error: expected ';' before 'next_pteg'
arch/powerpc/kvm/book3s_32_mmu_host.c:190: error: label 'next_pteg' used but not defined
make[1]: *** [arch/powerpc/kvm/book3s_32_mmu_host.o] Error 1
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A new label is also added to avoid freeing things that are known to not yet
be allocated.
A simplified version of the semantic match that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alexander Graf <agraf@suse.de>
The PAPR paravirtualization interface lets guests register three
different types of per-vCPU buffer areas in its memory for communication
with the hypervisor. These are called virtual processor areas (VPAs).
Currently the hypercalls to register and unregister VPAs are handled
by KVM in the kernel, and userspace has no way to know about or save
and restore these registrations across a migration.
This adds "register" codes for these three areas that userspace can
use with the KVM_GET/SET_ONE_REG ioctls to see what addresses have
been registered, and to register or unregister them. This will be
needed for guest hibernation and migration, and is also needed so
that userspace can unregister them on reset (otherwise we corrupt
guest memory after reboot by writing to the VPAs registered by the
previous kernel).
The "register" for the VPA is a 64-bit value containing the address,
since the length of the VPA is fixed. The "registers" for the SLB
shadow buffer and dispatch trace log (DTL) are 128 bits long,
consisting of the guest physical address in the high (first) 64 bits
and the length in the low 64 bits.
This also fixes a bug where we were calling init_vpa unconditionally,
leading to an oops when unregistering the VPA.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables userspace to get and set all the guest floating-point
state using the KVM_[GS]ET_ONE_REG ioctls. The floating-point state
includes all of the traditional floating-point registers and the
FPSCR (floating point status/control register), all the VMX/Altivec
vector registers and the VSCR (vector status/control register), and
on POWER7, the vector-scalar registers (note that each FP register
is the high-order half of the corresponding VSR).
Most of these are implemented in common Book 3S code, except for VSX
on POWER7. Because HV and PR differ in how they store the FP and VSX
registers on POWER7, the code for these cases is not common. On POWER7,
the FP registers are the upper halves of the VSX registers vsr0 - vsr31.
PR KVM stores vsr0 - vsr31 in two halves, with the upper halves in the
arch.fpr[] array and the lower halves in the arch.vsr[] array, whereas
HV KVM on POWER7 stores the whole VSX register in arch.vsr[].
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix whitespace, vsx compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables userspace to get and set various SPRs (special-purpose
registers) using the KVM_[GS]ET_ONE_REG ioctls. With this, userspace
can get and set all the SPRs that are part of the guest state, either
through the KVM_[GS]ET_REGS ioctls, the KVM_[GS]ET_SREGS ioctls, or
the KVM_[GS]ET_ONE_REG ioctls.
The SPRs that are added here are:
- DABR: Data address breakpoint register
- DSCR: Data stream control register
- PURR: Processor utilization of resources register
- SPURR: Scaled PURR
- DAR: Data address register
- DSISR: Data storage interrupt status register
- AMR: Authority mask register
- UAMOR: User authority mask override register
- MMCR0, MMCR1, MMCRA: Performance monitor unit control registers
- PMC1..PMC8: Performance monitor unit counter registers
In order to reduce code duplication between PR and HV KVM code, this
moves the kvm_vcpu_ioctl_[gs]et_one_reg functions into book3s.c and
centralizes the copying between user and kernel space there. The
registers that are handled differently between PR and HV, and those
that exist only in one flavor, are handled in kvmppc_[gs]et_one_reg()
functions that are specific to each flavor.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: minimal style fixes]
Signed-off-by: Alexander Graf <agraf@suse.de>
Avoid a race as described in the code comment.
Also remove a related smp_wmb() from booke's kvmppc_prepare_to_enter().
I can't see any reason for it, and the book3s_pr version doesn't have it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
