PaRAM set calculation is abstracted into its own function to
enable better reuse for other DMA cases such as cyclic. We adapt
the Slave SG case to use the new function.
This provides a much cleaner abstraction to the internals of the
PaRAM set. However, any PaRAM attributes that are not common to
all DMA types must be set separately such as setting of interrupts.
This function takes care of the most-common attributes.
Also added comments clarifying A-sync case calculations.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The earliest variants of the dma controller did not contain support for
controlling clocks.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some pl330 have per channel irq and it is necessary
to allocate all of them. Loop over irq assigned for this
device to support these pl330 IPs.
For example this IP is available on Xilinx Zynq platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Free memory allocated to edma_desc when failing to allocate slot.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 4981c4dc19 (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba7
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c1c63a14f4 (DMA: shdma: switch to managed
resource allocation) got rid of shdma_free_irq() but unfortunately got merged
later than commit c4f6c41ba7 (dma: add driver for
R-Car HPB-DMAC), so that the HPB-DMAC driver retained the calls and got broken:
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Allow the TI_EDMA to be built for ARCH_KEYSTONE which also supports
the EDMA IP.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This adds a new driver to support the s3c24xx dma using the dmaengine
and makes the old one in mach-s3c24xx obsolete in the long run.
Conceptually the s3c24xx-dma feels like a distant relative of the pl08x
with numerous virtual channels being mapped to a lot less physical ones.
The driver therefore borrows a lot from the amba-pl08x driver in this
regard. Functionality-wise the driver gains a memcpy ability in addition
to the slave_sg one.
The driver supports both the method for requesting the peripheral used
by SoCs before the S3C2443 and the different method for S3C2443 and later.
On earlier SoCs the hardware channels usable for specific peripherals is
constrainted while on later SoCs all channels can be used for any peripheral.
Tested on a s3c2416-based board, memcpy using the dmatest module and
slave_sg partially using the spi-s3c64xx driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for suspend/resume functionality to the cppi41
DMA driver. The steps necessary to make the system resume properly were
figured out by trial-and-error. The code as it stands now is the
minimum that has to be done to put the musb host system on an AM33xx
system into an operable state after resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dst_addr_width and src_addr_width should be a power of 2. Currently the
driver checks, that they both lie between 1 and 8 and that they are equal
to 1 or even. This however leaves an invalid value of 6 uncaught. Use an
explicit power of 2 check instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
[typo fix on changelog]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Makes the code more readable and compact. No functional change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of passing around struct plafform_device, use struct device and
save one level of dereferencing. This affects the following functions:
* cppi41_add_chans
* purge_descs
* deinit_cpii41
* init_descs
* init_cppi41
* cppi_glue_infos
It's just a cosmetic cleanup that makes the code more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
tegra_dma_prep_dma_cyclic is referenced only in this file.
Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The TI_EDMA driver unconditionally calls functions provided by the
TI_PRIV_EDMA code, but it doesn't force that to be built-in. If that isn't
otherwise enabled somewhere, you can get build errors like:
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:593: undefined reference to `edma_free_slot'
drivers/built-in.o: In function `edma_terminate_all':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:169: undefined reference to `edma_stop'
drivers/built-in.o: In function `edma_execute':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:122: undefined reference to `edma_write_slot'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:149: undefined reference to `edma_link'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:152: undefined reference to `edma_start'
Make TI_EDMA select TI_PRIV_EDMA to avoid this.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Matt's @ti.com address bounces. Update the MODULE_AUTHOR information in
edma.c to his Linaro address.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
Collection of random updates to the core and some end-driver fixups for
ioatdma and mv_xor:
* NUMA aware channel allocation
* Cleanup dmatest debugfs interface
* ioat: make raid-support Atom only
* mv_xor: big endian
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ldij
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine update from Dan Williams:
"Collection of random updates to the core and some end-driver fixups
for ioatdma and mv_xor:
- NUMA aware channel allocation
- Cleanup dmatest debugfs interface
- ioat: make raid-support Atom only
- mv_xor: big endian
Aside from the top three commits these have all had some soak time in
-next. The top commit fixes a recent build breakage.
It has been a long while since my last pull request, hopefully it does
not show. Thanks to Vinod for keeping an eye on drivers/dma/ this
past year"
* tag 'dmaengine-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: dma_sync_wait and dma_find_channel undefined
MAINTAINERS: update email for Dan Williams
dma: mv_xor: Fix incorrect error path
ioatdma: silence GCC warnings
dmaengine: make dma_channel_rebalance() NUMA aware
dmaengine: make dma_submit_error() return an error code
ioatdma: disable RAID on non-Atom platforms and reenable unaligned copies
mv_xor: support big endian systems using descriptor swap feature
mv_xor: use {readl, writel}_relaxed instead of __raw_{readl, writel}
dmatest: print message on debug level in case of no error
dmatest: remove IS_ERR_OR_NULL checks of debugfs calls
dmatest: make module parameters writable
These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NIZZ
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
Return directly if memory allocation fails. There is no need
of dma_free_coherent().
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull vfs pile 1 from Al Viro:
"Unfortunately, this merge window it'll have a be a lot of small piles -
my fault, actually, for not keeping #for-next in anything that would
resemble a sane shape ;-/
This pile: assorted fixes (the first 3 are -stable fodder, IMO) and
cleanups + %pd/%pD formats (dentry/file pathname, up to 4 last
components) + several long-standing patches from various folks.
There definitely will be a lot more (starting with Miklos'
check_submount_and_drop() series)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
direct-io: Handle O_(D)SYNC AIO
direct-io: Implement generic deferred AIO completions
add formats for dentry/file pathnames
kvm eventfd: switch to fdget
powerpc kvm: use fdget
switch fchmod() to fdget
switch epoll_ctl() to fdget
switch copy_module_from_fd() to fdget
git simplify nilfs check for busy subtree
ibmasmfs: don't bother passing superblock when not needed
don't pass superblock to hypfs_{mkdir,create*}
don't pass superblock to hypfs_diag_create_files
don't pass superblock to hypfs_vm_create_files()
oprofile: get rid of pointless forward declarations of struct super_block
oprofilefs_create_...() do not need superblock argument
oprofilefs_mkdir() doesn't need superblock argument
don't bother with passing superblock to oprofile_create_stats_files()
oprofile: don't bother with passing superblock to ->create_files()
don't bother passing sb to oprofile_create_files()
coh901318: don't open-code simple_read_from_buffer()
...
With this series, this check is no longer required and
we shouldn't need to reject drivers DMA'ing more than the
MAX number of slots.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dummy slot has been used as a way for missed-events not to be
reported as missing. This has been particularly troublesome for cases
where we might want to temporarily pause all incoming events.
For EDMA DMAC, there is no way to do any such pausing of events as
the occurence of the "next" event is not software controlled.
Using "edma_pause" in IRQ handlers doesn't help as by then the event
in concern from the slave is already missed.
Linking a dummy slot, is seen to absorb these events which we didn't
want to miss. So we don't link to dummy, but instead leave it linked
to NULL set, allow an error condition and detect the channel that
missed it.
Consider the case where we have a scatter-list like:
SG1->SG2->SG3->SG4->SG5->SG6->Null
For ex, for a MAX_NR_SG of 2, earlier we were splitting this as:
SG1->SG2->Null
SG3->SG4->Null
SG5->SG6->Null
Now we split it as
SG1->SG2->Null
SG3->SG4->Null
SG5->SG6->Dummy
This approach results in lesser unwanted interrupts that occur
for the last list split. The Dummy slot has the property of not
raising an error condition if events are missed unlike the Null
slot. We are OK with this as we're done with processing the
whole list once we reach Dummy.
Signed-off-by: Joel Fernandes <joelf@ti.com>
[modifed duplicate s-o-b & patch title]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In an effort to move to using Scatter gather lists of any size with
EDMA as discussed at [1] instead of placing limitations on the driver,
we work through the limitations of the EDMAC hardware to find missed
events and issue them.
The sequence of events that require this are:
For the scenario where MAX slots for an EDMA channel is 3:
SG1 -> SG2 -> SG3 -> SG4 -> SG5 -> SG6 -> Null
The above SG list will have to be DMA'd in 2 sets:
(1) SG1 -> SG2 -> SG3 -> Null
(2) SG4 -> SG5 -> SG6 -> Null
After (1) is succesfully transferred, the events from the MMC controller
donot stop coming and are missed by the time we have setup the transfer
for (2). So here, we catch the events missed as an error condition and
issue them manually.
In the second part of the patch, we make handle the NULL slot cases:
For crypto IP, we continue to receive events even continuously in
NULL slot, the setup of the next set of SG elements happens after
the error handler executes. This is results in some recursion problems.
Due to this, we continously receive error interrupts when we manually
trigger an event from the error handler.
We fix this, by first detecting if the Channel is currently transferring
from a NULL slot or not, that's where the edma_read_slot in the error
callback from interrupt handler comes in. With this we can determine if
the set up of the next SG list has completed, and we manually trigger
only in this case. If the setup has _not_ completed, we are still in NULL
so we just set a missed flag and allow the manual triggerring to happen
in edma_execute which will be eventually called. This fixes the above
mentioned race conditions seen with the crypto drivers.
[1] http://marc.info/?l=linux-omap&m=137416733628831&w=2
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Process SG-elements in batches of MAX_NR_SG if they are greater
than MAX_NR_SG. Due to this, at any given time only those many
slots will be used in the given channel no matter how long the
scatter list is. We keep track of how much has been written
inorder to process the next batch of elements in the scatter-list
and detect completion.
For such intermediate transfer completions (one batch of MAX_NR_SG),
make use of pause and resume functions instead of start and stop
when such intermediate transfer is in progress or completed as we
donot want to clear any pending events.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Changes are made here for configuring existing parameters to support
DMA'ing them out in batches as needed.
Also allocate as many as slots as needed by the SG list, but not more
than MAX_NR_SG. Then these slots will be reused accordingly.
For ex, if MAX_NR_SG=10, and number of SG entries is 40, still only
10 slots will be allocated to DMA the entire SG list of size 40.
Also enable TC interrupts for slots that are a last in a current
iteration, or that fall on a MAX_NR_SG boundary.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
Pull slave-dma fix from Vinod Koul:
"A fix for resolving TI_EDMA driver's build error in allmodconfig to
have filter function built in""
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma/Kconfig: TI_EDMA needs to be boolean
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
The relevant call to platform_get_resource was manually moved down to the
call to devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
kfree on a NULL pointer is a no-op. Null pointer check is
not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Trivial fix for function name mismatches I stumbled over.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for HPB-DMAC found in Renesas R-Car SoCs, using 'shdma-base' DMA
driver framework.
Based on the original patch by Phil Edworthy <phil.edworthy@renesas.com>.
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: removed useless #include, sorted #include's, fixed HPB_DMA_TCR_MAX,
fixed formats and removed line breaks in the dev_dbg() calls, rephrased and
added IRQ # to the shdma_request_irq() failure message, added MODULE_AUTHOR(),
removed '__init'/'__exit' annotations from the probe()/remove() methods, removed
'__initdata' annotation from 'hpb_dmae_driver', fixed guard macro name in the
header file, fixed #define ASYNCRSTR_ASRST20, added #define ASYNCRSTR_ASRST24,
added the necessary runtime PM calls to the probe() and remove() methods,
handled errors returned by dma_async_device_register(), beautified comments
and #define's.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sparse report the following warnings:
drivers/dma/imx-sdma.c:330:25: warning: symbol 'sdma_imx31' was not declared. Should it be static?
drivers/dma/imx-sdma.c:351:25: warning: symbol 'sdma_imx25' was not declared. Should it be static?
drivers/dma/imx-sdma.c:357:25: warning: symbol 'sdma_imx35' was not declared. Should it be static?
drivers/dma/imx-sdma.c:375:25: warning: symbol 'sdma_imx51' was not declared. Should it be static?
drivers/dma/imx-sdma.c:395:25: warning: symbol 'sdma_imx53' was not declared. Should it be static?
drivers/dma/imx-sdma.c:414:25: warning: symbol 'sdma_imx6q' was not declared. Should it be static?
Make the sdma_driver_data structures static.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
pch_dma currently isn't auto-loaded if built as a module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Many audio interface drivers require support of cyclic transfers to work
correctly, for example Samsung ASoC DMA driver. This patch adds support
for cyclic transfers to the amba-pl08x driver.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
[tfiga: Rebase and slightly beautify the original patch.]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are more fields than just SWIDTH in CH_CONTROL register, so read
register value must be masked in addition to shifting.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL080S has separate register to store transfer size in, allowing single
transfer to be much larger than in standard PL080.
This patch makes the amba-pl08x driver aware of this and removes writing
transfer size to reserved bits of CH_CONTROL register on PL080S, which
was not a problem witn transfer sizes fitting the original bitfield
of PL080, but now would overwrite other fields.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL080S is a modified version of PL080 that can be found on Samsung SoCs,
such as S3C6400 and S3C6410.
It has different offset of CONFIG register, separate CONTROL1 register
that holds transfer size and larger maximum transfer size.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch refactors debugging code that dumps LLI entries by moving it
into separate function, which is stubbed when VERBOSE_DEBUG is not
selected. This allows us to get rid of the ugly ifdef from the body of
pl08x_fill_llis_for_desc().
No functional change is introduced by this patch.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently memory allocated for LLIs is casted to an array of structs,
which is fragile and also limits the driver to a single, predefined LLI
layout, while there are some variants of PL08x, which have more fields
in LLI (namely PL080S with its extra CCTL2).
This patch makes LLIs a sequence of 32-bit words, which is just filled
with appropriate values in appropriate order and padded with required
amount of dummy words (currently zero, but PL080S will make better use
of this).
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some variants of PL08x (namely PL080S, found in Samsung S3C64xx SoCs)
have CONFIG register at different offset. This patch makes the driver
use offset from vendor data struct.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Further patch will introduce support for PL080S, which requires some
things to be done conditionally, thus increasing indentation level of
some functions even more.
This patch reduces indentation level of pl08x_getbytes_chan() function
by inverting several conditions and returning from function wherever
possible.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The test here should be ">=" instead of ">". The cdd->chan_busy[] array
has "ALLOC_DECS_NUM" elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pl330 DMA driver is broken in regard to handling a terminate all request
while it is processing the list of completed descriptors. This is most visible
when calling dmaengine_terminate_all() from within the descriptors callback for
cyclic transfers. In this case the TERMINATE_ALL transfer will clear the
work_list and stop the transfer. But after all callbacks for all completed
descriptors have been handled the descriptors will be re-enqueued into the (now
empty) work_list. So the next time dma_async_issue_pending() is called for the
channel these descriptors will be transferred again which will cause data
corruption. Similar issues can occur if dmaengine_terminate_all() is not called
from within the descriptor callback but runs on a different CPU at the same time
as the completed descriptor list is processed.
This patch introduces a new per channel list which will hold the completed
descriptors. While processing the list the channel's lock will be held to avoid
racing against dmaengine_terminate_all(). The lock will be released when calling
the descriptors callback though. Since the list of completed descriptors might
be modified (e.g. by calling dmaengine_terminate_all() from the callback) we can
not use the normal list iterator macros. Instead we'll need to check for each
loop iteration again if there are still items in the list. The drivers
TERMINATE_ALL implementation is updated to move descriptors from both the
work_list as well the new completed_list back to the descriptor pool. This makes
sure that none of the descripts finds its way back into the work list and also
that we do not call any futher complete callbacks after
dmaengine_terminate_all() has been called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With enabled pm_runtime in the kernel the device won't work because it
is not "on" during the probe function. This patch enables the device via
pm_runtime on probe so it remains activated.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before Randy figures out that this does not compile with CONFIG_BUG=n
here is a fix for it.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A bad merge resulted in a left-over free_irq() call. This patch removes it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This configuration data will be used, when DMAC DT support is added to
r8a73a4.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All shdma DMACs on ARM SoCs share certain register layout patterns, which
are currently defined in arch/arm/mach-shmobile/include/mach/dma-register.h.
That header is included by SoC-specific setup-*.c files to be used in DMAC
platform data. That header, however, cannot be directly used by the driver.
This patch copies those defines into a driver-local header to be used by
Device Tree configurations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Macros, named like TEND or SAR lack a namespace and are too broadly named
for a global header. Besides, they aren't needed globally. Move them to
where they belong - into the driver. Some other macros aren't used at all,
remove them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This facilitates DMAC DT support by eliminating the need in AUXDATA and
avoiding creating complex DT data. This also fits well with DMAC devices,
of which SoCs often have multiple identical copies and it is perfectly
valid to use a single configuration data set for all of them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Platform data shouldn't be changed at run-time, so, pointers to it should
be const.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Switch shdma to using devm_* managed functions for allocation of memory,
requesting IRQs, mapping IO resources etc.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On newer r-car SoCs the CHCLR register only contains one bit per channel,
to which a 1 has to be written to reset the channel. Older SoC versions had
one CHCLR register per channel, to which a 0 must be written to reset the
channel and clear its buffers. This patch adds support for the newer
layout.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This adds the ROM script addresses for i.MX25, i.MX5x and i.MX6 to the
SDMA driver needed for the driver to work without additional firmware.
The ROM script addresses are SoC specific and in some cases even tapeout
specific. This patch adds the ROM script addresses only for SoCs which
do not have a tapeout specific SDMA ROM, because currently it's unclear
how this case should be handled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use a struct type instead of an enum type for distinguishing between
different versions. This makes it simpler to handle multiple differences
without cluttering the code with comparisons for certain devtypes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As the driver now has its own xlate function and makes use of the
dma_get_slave_channel(), we need to manually set the DMA_PRIVATE flags.
Drivers which rely on of_dma_simple_xlate() do implicitly the same by
going through __dma_request_channel().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Provide a callback to prepare cyclic DMA transfers.
This is for instance needed for audio channel transport.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to fully support multiple transactions per channel, we need to
assure we get an interrupt for each completed transaction. That flags
bit is also our only way to tell at which descriptor a transaction ends.
So, remove the manual clearing of that bit, and then inline the only
remaining command that is left in append_pending_queue() for better
readability.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, when an interrupt has occured for a channel, the tasklet
worker code will only look at the very last entry in the running list
and complete its cookie, and then dispose the entire running chain.
Hence, the first transaction's cookie will never complete.
In fact, the interrupt we should handle will be the one related to the
first descriptor in the chain with the ENDIRQEN bit set, so complete
the second transaction that is in fact still running.
As a result, the driver can't currently handle multiple transactions on
one chanel, and it's likely that no drivers exist that rely on this
feature.
Fix this by walking the running_chain and look for the first
descriptor that has the interrupt-enable bit set. Only queue
descriptors up to that point for completion handling, while leaving
the rest intact. Also, only make the channel idle if the list is
completely empty after such a cycle.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of big endian CPU we have to convert either all fields in the structure
or leave this job to ACPICA. The second choice seems the best.
So, let's remove the ugly conversion that is not fully comprehensive anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If "num_disabled" is equal to STEDMA40_MAX_PHYS (32) then we would write
one space beyond the end of the pdata->disable_channels[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When CONFIG_ARM_LPAE=y the following build warning are generated:
drivers/dma/ste_dma40.c:3228:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
drivers/dma/ste_dma40.c:3582:3: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
drivers/dma/ste_dma40.c:3582:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t' [-Wformat]
drivers/dma/ste_dma40.c:3593:5: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Also, for printing memory region the '%pr' is more convenient.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix:
arch/arm/common/built-in.o: undefined reference to `edma_filter_fn'
seen with "make ARCH=arm allmodconfig"
Commit 6cba4355 (ARM: edma: Add DT and runtime PM support to the private EDMA
API) adds a dependency on edma_filter_fn() into arch/arm/common/edma.c. Since
this file is always built into the kernel, edma_filter_fn() must be built into
the kernel as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the shdma driver __iomem pointers are used to point to hardware
registers. Using typed pointers like "u32 __iomem *" in this case is
inconvenient, because then offsets, added to such pointers, have to be
devided by sizeof(u32) or similar. Switch the driver to use void
pointers, which avoids this clumsiness.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
struct sh_dmae_device::chan_reg is a pointer to u32, therefore when adding
offsets to it care should be taken to add offsets in sizeof(u32) units, not
in bytes. This patch corrects such a bug. While at it we also remove the
redundant parameter of the affected function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Building dma_v3.o triggers a GCC warning:
drivers/dma/ioat/dma_v3.c: In function ‘__ioat3_prep_pq16_lock’:
drivers/dma/ioat/dma_v3.c:264:11: warning: array subscript is below array bounds [-Warray-bounds]
drivers/dma/ioat/dma_v3.c:264:11: warning: array subscript is below array bounds [-Warray-bounds]
This warning is caused by pq16_set_src(). It uses "int idx" as an index
to an eight element array. Changing "idx" to "unsigned" silences this
warning. Apparently GCC can then determine that "idx" will never be
negative.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
dma_channel_rebalance() currently distributes channels by processor ID.
These IDs often change with the BIOS, and the order isn't related to
the DMA channel list (related to PCI bus ids).
* On my SuperMicro dual E5 machine, first socket has processor IDs [0-7]
(and [16-23] for hyperthreads), second socket has [8-15]+[24-31]
=> channels are properly allocated to local CPUs.
* On Dells R720 with same processors, first socket has even processor IDs,
second socket has odd numbers
=> half the processors get channels on the remote socket, causing
cross-NUMA traffic and lower DMA performance.
Change nth_chan() to return the channel with min table_count and in the
NUMA node of the given CPU, if any. If none, the (non-local) channel with
min table_count is returned. nth_chan() is therefore renamed into min_chan()
since we don't iterate until the nth channel anymore. In practice, the
behavior is the same because first channels are taken first and are then
ignored because they got an additional reference.
The new code has a slightly higher complexity since we always scan the
entire list of channels for finding the minimal table_count (instead
of stopping after N chans), and because we check whether the CPU is in the
DMA device locality mask. Overall we still have time complexity =
number of chans x number of processors. This rebalance is rarely used,
so this won't hurt.
On the above SuperMicro machine, channels are still allocated the same.
On the Dells, there are no locality issue anymore (MEMCPY channel X goes
to processor X and to its hyperthread sibling).
Signed-off-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Dan Williams <djbw@fb.com>
Disable RAID on non-Atom platform and remove related fixups such as the
64-byte alignement restriction on legacy DMA operations (introduced in
commit f26df1a1 as a workaround for silicon errata).
Signed-off-by: Brice Goglin <Brice.Goglin@inria.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
The mv_xor driver had never been used in a big-endian context, and
therefore was not using the hardware features to support such an
execution environment. The hardware provides a "descriptor swap" bit
that automatically swaps the bytes of the DMA descriptors, within
blocks of 8 bytes. This requires a different DMA descriptor layout on
big-endian systems, as well as enabling this "descriptor swap" bit.
This mechanism is exactly identical to the one already used in the
mv643xx_eth network driver and the mvneta network driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Dan Williams <djbw@fb.com>
In order to support big-endian execution, the mv_xor driver is changed
to use the readl_relaxed() and writel_relaxed() accessors that
properly convert from the CPU endianess to the device endianess (which
in the case of Marvell XOR hardware is always little-endian).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Let's move the behaviour of printing no error message back to the pre v3.10
times. It means we will use debug level in the described case, and a warning
level otherwise.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
There is a really little chance when we are able to create a directory and are
not able to create nodes under it. So, this patch just removes those checks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
The debugfs interface brought a copy of the test case parameters. This makes
different set of values under /sys/module/dmatest/parameters/ and
/sys/kernel/debug/dmatest/. The user might be confused by the divergence of
values.
The proposed solution in this patch is to make module parameters writable and
remove them from the debugfs. Though we're still using debugfs to control test
runner and getting results.
Documentation part is updated accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Dan Williams <djbw@fb.com>
Signed-off-by: Dan Williams <djbw@fb.com>
In Rob's recent pull request the patch
ARM: highbank: select ARCH_DMA_ADDR_T_64BIT for LPAE
promotes dma_addr_t to 64bit, so printk generates a warning about
an incorrect type. Fix this by casting it to u64 and using %llx.
Fixing long lines on the way.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
When dma_addr_t is 64 bits long, compilation of the AMBA PL08x DMA
driver breaks due to a missing 64bit%8bit modulo operation.
Looking more closely the divisor in these operations can only be
1, 2 or 4, so the full featured '%' modulo operation is overkill and
can be replaced with simple bit masking.
Change from v1:
Replace open-coded function with existing IS_ALIGNED macro and use a
macro around that to avoid a line becoming too long.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
With all mxs-dma clients moved to use generic DMA helper, the code
left from generic DMA binding conversion can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After the patch: "2ccaef0 dma: imx-sdma: make channel0 operations atomic",
the "done" completion is not used any more.
Just remove it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PXA DMA controller has a DALGN register which allows for
byte-aligned DMA transfers. Use it in case any of the transfer
descriptors is not aligned to a mask of ~0x7.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA_SLAVE is currently set twice.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch makes the mmp_pdma controller able to provide DMA resources
in DT environments by providing an dma xlate function.
of_dma_simple_xlate() isn't used here, because if fails to handle
multiple different DMA engines or several instances of the same
controller. Instead, a private implementation is provided that makes use
of the newly introduced dma_get_slave_channel() call.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PXA peripherals need to obtain specific DMA request ids which will
eventually be stored in the DRCMR register.
Currently, clients are expected to store that number inside the slave
config block as slave_id, which is unfortunately incompatible with the
way DMA resources are handled in DT environments.
This patch adds a filter function which stores the filter parameter
passed in by of-dma.c into the channel's drcmr register.
For backward compatability, cfg->slave_id is still used if set to
a non-zero value.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There's no reason for limiting the maximum transfer length to 0x1000.
Take the actual bit mask instead; the PDMA is able to transfer chunks of
up to SZ_8K - 1.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As suggested by Ezequiel García, release the spinlock at the end of the
function only, and use a goto for the control flow.
Just a minor cleanup.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The exact same calculation is done twice, so let's factor it out to a
macro.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
This patch adds __pl330_giveback_descs which give back descriptors when fails
allocating descriptors. It requires to eliminate duplication for
pl330_prep_dma_sg which will be added later.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Acked-by : Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch adds PM ops entries in sirf-dma drivers, so that this
driver can support suspend/resume, hibernation and runtime PM.
while suspending, sirf-dma will lose all registers, so we save
them at suspend and restore in resume for active channels.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
sirfsoc_dma_prep_cyclic() returns pointer, thus NULL should be
used instead of 0 in order to fix the following sparse warning:
drivers/dma/sirf-dma.c:598:24: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
%p is used, thus NULL should be used instead of 0
in order to fix the following sparse warning:
drivers/dma/mv_xor.c:648:9: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mmp_pdma_alloc_descriptor() is used only in this file.
Fix the following sparse warning:
drivers/dma/mmp_pdma.c:359:25: warning: symbol 'mmp_pdma_alloc_descriptor' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver is currently used by musb' cppi41 couter part. I may merge
both dma engine user of musb at some point but not just yet.
The driver seems to work in RX/TX mode in host mode, tested on mass
storage. I increaed the size of the TX / RX transfers and waited for the
core code to cancel a transfers and it seems to recover.
v2..3:
- use mall transfers on RX side and check data toggle.
- use rndis mode on tx side so we haveon interrupt for 4096 transfers.
- remove custom "transferred" hack and use dmaengine_tx_status() to
compute the total amount of data that has been transferred.
- cancel transfers and reclaim descriptors
v1..v2:
- RX path added
- dma mode 0 & 1 is working
- device tree nodes re-created.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In mmp pdma, phy channels are allocated/freed dynamically.
The mapping from DMA request to DMA channel number in DRCMR
should be cleared when a phy channel is freed. Otherwise
conflicts will happen when:
1. A is using channel 2 and free it after finished, but A
still maps to channel 2 in DRCMR of A.
2. Now another one B gets channel 2. So B maps to channel 2
too in DRCMR of B.
In the datasheet, it is described that "Do not map two active
requests to the same channel since it produces unpredictable
results" and we can observe that during test.
Signed-off-by: Xiang Wang <wangx@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mmp pdma, phy channels are allocated/freed dynamically
and frequently. But no proper protection is added.
Conflict will happen when multi-users are requesting phy
channels at the same time. Use spinlock to protect.
Signed-off-by: Xiang Wang <wangx@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To obey a usual practice let's return DMA_PAUSED status only if
dma_cookie_status returned DMA_IN_PROGRESS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no point to go throught the rest of the function if first call to
dma_cookie_status() returned DMA_SUCCESS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the PC world is quite possible that devices are sharing the same interrupt
line. The patch prepares dw_dmac driver to such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In general ~0 does not fit some integer types. Let's do a helper to make a
comparison with that constant properly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In rare cases (mostly for the testing purposes) the dw_dmac driver might be
compiled as a module as well as the other LPSS device drivers (I2C, SPI,
HSUART). When udev handles the event of the devices appearing the dw_dmac
module is missing. This patch will fix that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes sparse warning:
drivers/dma/acpi-dma.c:76:21: sparse: cast to restricted __le32
Since everything in all ACPI tables is little-endian, by definition, the used
types in practice are uXX. Thus, we have to enforce __leXX if we want to
convert them to CPU order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no point to go throught the rest of the function if first call to
dma_cookie_status() returned DMA_SUCCESS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_set_residue() sets only residue value, so user can't rely on the returned
values of cookies. That patch standardize the behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It's better to use generic dma_cookie_status() that allows user to get standard
possible return codes independently of the DMAC driver in charge.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to dma_cookie_status() description locking is not required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to dma_cookie_status() description locking is not required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to dma_cookie_status() description locking is not required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to dma_cookie_status() description locking is not required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to dma_cookie_status() description locking is not required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to dma_cookie_status() description locking is not required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Residue value is assigned to 0 by dma_cookie_status().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
last_used variable is applied only once, so, let's substitute it by its value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
last_used variable is applied only once, so, let's substitute it by its value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
sh_desc->hw.tcr is controlling real data size,
and, register TCR is controlling data transfer count
which was xmit_shifted value of hw.tcr.
Current sh_dmae_get_partial() is calculating in different unit.
This patch fixes it.
This bug has been present since c014906a87
("dmaengine: shdma: extend .device_terminate_all() to record partial
transfer"), which was added in 2.6.34-rc1.
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allocate a descriptor for each period of a cyclic transfer, not just the first.
Also since the callback needs to be called for each finished period make sure to
initialize the callback and callback_param fields of each descriptor in a cyclic
transfer.
Cc: stable@vger.kernel.org
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the dma dma_devclass code to use
the correct field.
Cc: Dan Williams <djbw@fb.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return -ENODEV when no proper base address found error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
