The dw_spi_dma_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When submitting an identical spi_message multiple times via spi_sync
the spi_message.frame_length does not get reset to 0 in __spi_validate
before adding up all spi_transfer.len resulting in
frame_length > actual_length on all but the first spi_sync call.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
mtk_spi_probe() calls pm_runtime_enable(), after
pm_runtime_enable() is called, it should call
pm_runtime_disable() in the failure flow.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Handle EPROBE_DEFER explicitly so that we ensure that we get the DMA
channel specified in the device tree, instead of depending on the DMA
controller getting probed before us.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not need to re-read and re-write SPI_CMD_REG, so remove it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI
chip select signals") added a block where lpss_ssp_setup() gets called
again for Intel LPSS SPI host controllers before checking number of chip
selects from the capabilities register.
There is no point in calling the function twice in probe so remove the
first call.
Reported-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in DT, these calls turn
to NOPs.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow transfers to set the transmission speed rather than using the
device max_speed_hz value. The SPI core makes sure that the speed_hz
value is always set on the transfer.
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s3c64xx platform data already contains a pointer to the
DMA filter function, but not to the associated data.
This simplifies the code and makes it more generic by
passing the data along with the filter function like
we do for other drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
With a 64-bit resource_size_t, we get a build warning on bcm63xx_spi_probe:
drivers/spi/spi-bcm63xx.c:565:16: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
As we are printing a resource, we can just use the %pr format
specifier that pretty-prints the address and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When only one device is present, it is not necessary to specify
cs_gpios, as the CS line can be controlled by the hardware
module.
Without this patch, older device tree bindings used before
37457607 "spi: mediatek: mt8173 spi multiple devices support"
would cause a panic on boot. This fixes the crash, and
re-introduces backward compatibility.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_setup_transfer’:
drivers/spi/spi-bcm63xx.c:207: warning: ‘clk_cfg’ may be used uninitialized in this function
While this is a false positive, it can easily be avoided by selecting
the default clock configuration first.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ca5d248542 ("spi: Add THIS_MODULE to spi_driver in SPI core")
adds the new __spi_register_driver() function, but keeps the kerneldoc
for the spi_register_driver() function in place and forgets to add the
description for the new owner parameter.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the pxa2xx_spi_acpi_get_pdata() so that it can create platform data
also on platforms that do not support ACPI or if CONFIG_ACPI is not set.
Now it is expected that "pxa2xx-spi" platform device is either created with
explicit platform data or has an ACPI companion device.
However there is only little in pxa2xx_spi_acpi_get_pdata() that is really
dependent on ACPI companion and it can be reworked to cover also cases
where "pxa2xx-spi" device doesn't have ACPI companion and is created
without platform data.
Do this by renaming the pxa2xx_spi_acpi_get_pdata(), moving it outside of
CONFIG_ACPI test and changing a few runtime tests there to support non-ACPI
case. Only port/bus ID setting based on ACPI _UID is dependent on ACPI and
is moved to own function inside CONFIG_ACPI.
Purpose of this to support non-ACPI case for those PCI enumerated compound
devices that integrate both LPSS SPI host controller and integrated DMA
engine under the same PCI ID and which are registered in MFD layer instead
of in spi-pxa2xx-pci.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LPSS SPI in Intel Broxton is otherwise the same than in Intel Sunrisepoint
but it supports up to four chip selects per port and has different FIFO
thresholds. Patch adds support for two Broxton SoC variants.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI capabilities register located in private registers space of newer
Intel LPSS SPI host controllers tell in register bits 12:9 which chip
select signals are enabled.
Use that information for detecting the number of chip selects. For
simplicity we assume chip selects are enabled one after another without
disabled chip selects between. For instance CS0 | CS1 | CS2 but not
CS0 | CS1 | CS3.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS SPI host controllers in upcoming Intel platforms can have up
to 4 chip selects per port. Extend chip select control in
lpss_ssp_cs_control() by adding a code that selects the active chip
select output prior to changing the state. Detection for number of
enabled chip select signals will be added by another patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename a few defines that are specific to Intel LPSS SPI private
registers with LPSS prefix. It makes easier to distinguish them from
common defines.
Suggested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LS1043a and LS2080A in the Layerscape family also support DSPI, make
DSPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
there's no need to call pm_runtime_get_sync()
followed by pm_runtime_put(). We should, instead,
just call pm_runtime_put_sync() and pm_runtime_disable().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some users have reported that in polled mode the driver fails randomly
to read the last word of the transfer.
The end condition used for the transmissions (in polled and irq mode)
has been the TX_EMPTY flag. But Lars-Peter Clausen has identified a delay
from the TX_EMPTY to the actual end of the data rx.
I believe that this race condition has not been detected until now
because of the latency added by the IRQ handler or the PCIe bridge.
This bugs affects setups with low latency access to the spi core.
This patch replaces the readout logic:
For all the words, except the last one, the TX_EMPTY flag is used (and
cached).
If !TX_EMPY or is the last word. The status register is read and the
RX_EMPTY flag is used.
The performance is not affected: there is an extra read of the
Status Register, but the readout can start as soon as there is a word
in the buffer.
Reported-by: Edward Kigwana <ekigwana@scires.com>
Initial-fix-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_register_driver helper macro that adds THIS_MODULE to
spi_driver for the registering driver. We rename and modify
the existing spi_register_driver to enable this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI controllers may need to be properly setup before chip selects
can be used. Therefore, wait until the spi controller has a chance
to perform their setup procedure before trying to use the chip
select.
This also insures that the chip selects pins are in a good
state before asseting them which otherwise may cause confusion.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset 0x60 is the offset of the data register defined as DW_SPI_DR in the
header file. Use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mt8173 IC spi HW has 4 gpio group, it's possible to support
max <= 4 slave devices, even mtk spi HW is not congruent to spi core.
1. When a device do a spi_message transfer, spi HW should know
which pad-group this device is on, and then writes pad-select
register.
2. Mtk pad-select register just selects which MISO pin HW will
receive data. For example, pad-select=1(select spi1 pins), HW just
receives data from spi1 MISO, but it still send waveform to all 4
group cs/clk/mosi. If cs pin in other groups is still spi mode,
after spi1 is selected(by active cs pin), devices on other group
will also be selected.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
controller_data is related with device, so move to master->setup
function.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mtk_spi_config() and mtk_spi_prepare_message() both initialize
spi register, so remove mtk_spi_config() and init all register
in mtk_spi_prepare_message().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building docs with make htmldocs, warnings about not having
a description for the return value are reported, i.e:
warning: No description found for return value of 'spi_register_driver'
Fix these by following the kernel-doc conventions explained in
Documentation/kernel-doc-nano-HOWTO.txt.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add more indentation to define lines for making them aligned with the
longest one. They would look messy after adding more long defines.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Upcoming Intel platforms use LPSS SPI_CS_CONTROL register bits 15:12 for
configuring the chip select polarities. Touch only chip select SW mode and
state bits when enabling the software chip select control in order to not
clear any other bits in the register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy noticed numeric unique device ID is unsigned integer so convert it
using kstrtouint(). Actually integer in ACPI 2.0 and later is 64 bits
litte-endian unsigned integer but quite certainly having so big value here
would mean something extra than just the SPI bus number so it won't hurt to
assume only lower 32 bits carry the bus number for now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we call pxa2xx_ssp_get_clk_div() from pump_transfers() we may derive
pointer to struct chip_data from struct drv_data like it's done in the rest
of the functions. This will make it less errorprone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The speed can be changed from transfer to transfer, that's why the messages
do not depict the actual values during ->setup(). Move debug messages from
->setup() to pump_transfers(). Get rid of leftovers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed problem with setting spi mode 0 or 1 after setting mode 2 or 3
SPI_MODE_0 and SPI_MODE_1 requires clock low when inactive. SPI_MODE_2
and SPI_MODE_3 requires clk high when inactive.
Currently driver can just set bits in fields SCLK_PHA (SPI Clock/Data
Phase Control), SCLK_POL (SPI Clock Polarity Control),
SCLK_CTL (controls the inactive state of SCLK) ans SS_POL (SPI SS
Polarity Select) of ECSPIx_CONFIGREG register.
This patch allows driver to clear corresponding bits in these fields.
Signed-off-by: Andrew Y. Kuksov <qxovxp@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all register definitions and structs into the driver. This allows
us dropping the platform_data struct and drop any arch specific
includes. Make use of different device names to identify the version of
the block we have.
Since we now have full control over the message width, we can drop the
size check, which was broken anyway, since it never set ret to any error
code.
Also since we now have no arch depedendent resources, we can now allow
compiling it for any arch, hidden behind COMPILE_TEST.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA-slave configuration depends on the whether <= 8 or > 8 bits
are transferred per word, so we need to call
atmel_spi_dma_slave_config() with the correct value.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since the "Switch driver to use transfer_one" change, the cs_change
behavior has changed and a channel chip select can still be
asserted when changing channel from a previous last transfer in a
message having the cs_change attribute.
Since there is no sense having multiple chip select being asserted at the
same time, disable all the remaining forced chip selects in a the
prepare_message called right before a spi_transfer_one_message call.
It ignores the current channel configuration in order to keep the
possibility to leave the chip select asserted between messages.
It fixes this bug on a DM8168 SoC ES2.1 Soc and an OMAP4 ES2.1 SoC.
It was hanging all the other channels transfers when a CHCONF_FORCE
is present on the wrong channel.
Fixes: b28cb9414d ("spi: omap2-mcspi: Switch driver to use transfer_one")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if GPIO pin is valid by API helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all users aware about calling dw_spi_remove_host() with properly set
parameter. Remove unneeded check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the driver to use unfied device property API instead of OF one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pdev member is not used anywhere, thus remove it. Moreover struct
dw_spi_pci becomes an equivalent of struct dw_spi and therefore remove entire
struct dw_spi_pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper disables SPI controller and sets clock to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_threshold and rx_threshold variables are not used anywhere. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point to have a separate variable for speed in ->transfer_one().
While here, remove !chip->clk_div from a condition since it is assigned
simultaneously with chip->speed_hz. We can do this safely because
a) transfer speed can't be higher than max_freq and therefore chip->clk_div
can be 0 only when chip->speed_hz is 0, and
b) transfer speed can't be 0, otherwise we will get division by zero
exception.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry over spi->bits_per_word and Co from ->setup() in
struct chip_data since ->transfer_one() will anyway take the transfer
parameters from struct spi_transfer. This is since SPI core validates both
bits_per_word transfer parameter and defaults to spi->bits_per_word in case
that per transfer parameter is not set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we recalculate cr0 each time we start a transfer the chip_data->cr0
becomes redundant. Remove it and related pieces.
This is a follow up to commit 0ed36990a9 (spi: dw: Remove needless if
statements).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name of the master device is set during registrationg which happens after
we issue the error message. Change it to plain struct device * to see which
device registration failed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use spi->cs_gpio directly to remove the following build warning:
drivers/spi/spi-davinci.c:219:6: warning: 'gpio' may be used uninitialized in this function
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently word completion interrupt is fired for transfer of every
word(8bit to 128bit in size). This adds a lot of overhead, and decreases
r/w throughput. It hardly takes 3us(@48MHz) for 128bit r/w to complete,
hence its better to poll on word complete bit to be set in
QSPI_SPI_STATUS_REG instead of using interrupts.
This increases the throughput by 30% in both read and write case.
So, switch to polling mode instead of interrupts to determine completion
of word transfer.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per discussion [1] the best choice is to set closest speed which is not
going over the asked one.
Do the same approach for Intel Quark boards.
[1] http://www.spinics.net/lists/linux-spi/msg03389.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Propagate the actual return code of __spi_validate_bits_per_word() in
spi_setup().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized
Also the use of irq_of_parse_and_map is replaced by platform_get_irq.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are strange issues with the auxiliary spi device that result
in "lost" data in the RX path if the fifo is filled by too much
(even though the status register is checked if new data can get filled
in).
This has been observed primarily for the interrupt case.
Polling works fine, probably because the RX fifo is pulled immediately
when in the tight polling loop.
For that reason we have to limit the pending bytes to less than 15
when filling the fifo in interrupt mode.
There also was an issue returning the "wrong" last 1/2 bytes
of a transfer when the transfer is not a multiple of 3 bytes.
(this impacted polling and interrupt modes)
Also fixed an overflow in the estimation of the transfer time used
to decide if we run in interrupt or polling mode (found with the
spi-bcm2835.c driver originally).
Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized
Also the use of irq_of_parse_and_map is replaced by platform_get_irq.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Writing invalid command to QSPI_SPI_CMD_REG will terminate current
transfer and de-assert the chip select. This has to be done before
calling spi_finalize_current_message(). Because
spi_finalize_current_message() will mark the end of current message
transfer and schedule the next transfer. If the chipselect is not
de-asserted before calling spi_finalize_current_message() then the next
transfer will overlap with the previous transfer leading to data
corruption.
__spi_pump_message() can be called either from kthread worker context or
directly from the calling process's context. It is possible that these
two calls can race against each other. But race is serialized by
checking whether master->cur_msg == NULL (pointer to msg being handled
by transfer_one() at present). The master->cur_msg is set to NULL when
spi_finalize_current_message() is called on that message, which means
calling spi_finalize_current_message() allows __spi_sync() to pump next
message in calling process context.
Now if spi-ti-qspi calls spi_finalize_current_message() before we
terminate transfer at hardware side, if __spi_pump_message() is called
from process context then the successive transactions can overlap.
Fix this by moving writing invalid command to QSPI_SPI_CMD_REG to
before calling spi_finalize_current_message() call.
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the IRQs for SPI client devices, registered via device-tree,
are mapped when the client devices are registered. If the corresponding
irq-chip has not been probed yet, then the probing of the client device
will fail and will not be retried. Resolve this by mapping the IRQ at
probe time and allow the probe to be deferred if the IRQ is not yet
available.
If of_irq_get() returns an error that is not -EPROBE_DEFER, then assume
that the SPI client does not have an IRQ and set the IRQ number to zero
(which is equivalent to irq_of_parse_and_map()).
This is based on some inputs from Thierry Reding <treding@nvidia.com>.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the message control word parameters part of the register offsets
array so we have them all in one struct.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct guard CONFIG_CPU_BIG_ENDIAN and the *be accessors to
follow native endianness on big endian systems.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835 has 2 auxiliary spi bus masters spi1 and spi2.
This implements the driver to enable these devices.
The driver does not implement native chip-selects but uses
the aribtrary GPIO-chip-selects provided by the spi-chipselect.
Note that this driver relies on the fact that
the clock is implemented by the clk-bcm2835-aux driver,
which enables/disables the HW block when requesting/releasing
the clock.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the bitbang driver to use the generic implementation of
transfer_one_message. This simplifies the bitbang driver code and
provides benefits like the statistics in the generic implementation.
Successfully tested on a IMX6-based system (spi-imx) and on a MIPS-based
router (OpenWRT with spi-ath79).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove an unneeded check. The SPI core (__spi_validate) takes care
that these fields are always populated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not used since commit 8d94cc50aa ("[PATCH] spi: stabilize PIO mode
transfers on PXA2xx systems").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was leftover from the legacy pxa2xx DMA implementation and not needed
anymore so remove it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by switching from devm_ioremap to devm_ioremap_resource.
Checking the result of platform_get_resource is not needed as
devm_ioremap_resource checks the provided resource argument for NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This makes possible to remove two if
statements and remove one code block that is never executed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get pointer to the struct acpi_device by using ACPI_COMPANION() macro. This
is more efficient than using ACPI_HANDLE() and acpi_bus_get_device().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Carry input clock of the controller in max_speed_hz of struct spi_master
instead of in own driver data. They mean the same thing and more over now
the max_speed_hz is not even set here.
As an added bonus this allows SPI core to validate that transfer speed is
not beyond the maximum input clock. This is not a problem in spi-pxa2xx as
the driver doesn't use transfer speed parameter directly but via input
clock divider calculation which will top at divide by one. However it's
better to validate speed before passing it here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
XTFPGA SPI controller has native endian registers.
Fix register acessors so that they work in big-endian configurations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
report transfer sizes as a histogram via the following files:
/sys/class/spi_master/spi*/statistics/transfer_bytes_histo_*
/sys/class/spi_master/spi*/spi*.*/statistics/transfer_bytes_histo_*
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There hasn't been need to carry chip->cr0 after SPI core started to
validate speed_hz and bits_per_word transfer parameters. That effectively
caused that pump_transfers() always recalculated it and practically
chip->cr0 is used locally in setup() for debug prints only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is continuation to previous commit by separating unindentation from
variable removal done in previous commit. As said SPI core have validated
both the speed_hz and bits_per_word and the if statement here evaluates
always to true.
Remove the test and unindent the code block accordingly. While at it remove
also needless "cr0 = chip->cr0" as cr0 will be overwritten anyway and fix
block comment style.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry spi->max_speed_hz and spi->bits_per_word from
setup() in "struct chip_data" since pump_transfers() will anyway take the
transfer parameters from "struct spi_transfer". This is since SPI core
validates both bits_per_word and speed_hz transfer parameters and defaults
to spi->bits_per_word and spi->max_speed_hz in case these per transfer
parameters are not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core makes sure that transfer speed is always set so code here writes
the same register with the same value twice. Code has been doing this from
the beginning.
This looks to me some sort of copy paste error so I'm removing the second
write. If this is not the case we can bring it back with a comment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Test for non-zero spi->max_speed_hz in dw_spi_setup() looks needless as
spi_setup() defaults to master->max_speed_hz in case it is not set. This
drivers sets the master->max_speed_hz based on max_freq data passed to it
via dw_spi_add_host() call. I suppose things have already fallen apart if
dw_spi_mmio_probe() or spi_pci_probe() ever passes zero max_freq.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This allows to remove related if
statements as they evaluate always to true and reduce indentation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set.
This allows to remove a few if statements around per transfer bits_per_word
and speed_hz tests as they evaluate always to true.
Also defaulting word_len to 8 is needless since spi_setup() has already
made sure spi->bits_per_word is 8 in case it is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This allows to remove two needless tests
from uwire_txrx() and uwire_setup_transfer().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
thus the if statement here is needless as it will always call the
mpc512x_psc_spi_transfer_setup().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
chipselect (in the case of spi-gpio: spi_gpio_chipselect, which
calls gpiod_set_raw_value_cansleep) can sleep, so we should not
hold a spinlock while calling it from spi_bitbang_setup.
This issue was introduced by this commit, which converted spi-gpio
to cansleep variants:
d9dda5a191 "spi: spi-gpio: Use 'cansleep' variants to access GPIO"
Replacing the lock variable by a mutex fixes the issue: This is
safe as all instances where the lock is used are called from
contexts that can sleep.
Finally, update spi-ppc4xx and and spi-s3c24xx to use mutex
functions, as they directly hold the lock for similar purpose.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This can simplify a little the
au1550_spi_setupxfer() as there is need to check only for valid
"struct spi_transfer" pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set so code here won't use the
chip->baud value (which is derived from spi->max_speed_hz).
Please note driver uses chip->baud at the beginning of message transmission
by calling the bfin_spi_restore_state() but then programs per transfer
speed in bfin_spi_pump_transfers(). I'm not familiar with the HW so I don't
know would it be possible to remove chip->baud completely by either using
constant value in bfin_spi_restore_state() or by removing the baud register
write there.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set so code here won't use the
chip->baud value (which is derived from spi->max_speed_hz).
Please note driver uses chip->baud at the beginning of message transmission
by calling the bfin_sport_spi_restore_state() but then programs per
transfer speed in bfin_sport_spi_pump_transfers(). I'm not familiar with
the HW so I don't know would it be possible to remove chip->baud completely
by either using constant value in bfin_sport_spi_restore_state() or by
removing the tclkdiv register write there.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit adcbcfea15 ("spi: mediatek: fix spi clock usage error")
added a new sel_clk but introduced bugs in the error paths since
the wrong struct clk pointers are passed to PTR_ERR().
Fixes: adcbcfea15 ("spi: mediatek: fix spi clock usage error")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove use of spi_unregister_master in remove function as
devm_spi_register_master in probe function automatically
handles it. To be compatible with the change, use direct
return instead of goto and remove unnedded label out.
Also, remove bcm53xxspi_bcma_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace all bcm_read* with (io)read. Due to this block following
system endianness, make sure we match that.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass 0 as the spi bus number, so we might as well hard code
it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass 8 for the number of chip selects, so we can as well
hardcode it to this number.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following warning:
drivers/spi/spi-bcm63xx.c:125:5: warning: unused variable 'rx_tail' [-Wunused-variable]
u8 rx_tail;
^
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify s3c64xx_spi_remove by replacing the clock disabling with calling
runtime PM suspend which does the same.
Waking up the device if it was suspended wouldn't be strictly needed
for this driver but using pm_runtime_get_sync is cleaner and makes
s3c64xx_spi_remove more consistent with the runtime PM handling in
s3c64xx_spi_setup.
pm_runtime_force_suspend does most of the work for us:
disabling the clocks, disabling runtime PM and setting it to
"suspended" state.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The runtime PM suspend / resume handlers take care of the enabling/
disabling the clocks already. Therefore replace the duplicated
clock handling with pm_runtime_force_suspend/resume.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver to make full use of runtime PM autosuspend.
Before only the SPI core was instructed to use autosuspend
by setting master->auto_runtime_pm. Nevertheless due to the missing
pm_runtime_use_autosuspend call autosuspend wasn't active.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the last close we are freeing spidev if spidev->spi is NULL, but
just before checking if spidev->spi is NULL we are dereferencing it.
Lets add a check there to avoid the NULL dereference.
Fixes: 9169051617 ("spi: spidev: Don't mangle max_speed_hz in underlying spi device")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_PM is defined but not CONFIG_PM_SLEEP (this happens when
CONFIG_SUSPEND is not defined), there is the following warning:
drivers/spi/spi-atmel.c:1723:12: warning: ‘atmel_spi_suspend’ defined but not used [-Wunused-function]
drivers/spi/spi-atmel.c:1741:12: warning: ‘atmel_spi_resume’ defined but not used [-Wunused-function]
Enclose both atmel_spi_suspend and atmel_spi_resume in #ifdef
CONFIG_PM_SLEEP/#endif to solve that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a bug in the alignment checking of transfers,
that results in DMA not being used for un-aligned
transfers that do not cross page-boundries, which is valid.
This is due to a missconception of the meaning PAGE_MASK
when implementing that check originally - (PAGE_SIZE - 1)
should have been used instead.
Also fixes a copy/paste error.
Reported-by: <robert@axium.co.nz>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Mediatek spi HW can't set cs inactive(keep cs high) directly.
Instead, it supplies pause mode to do it indirectly. If driver
unsets SPI_CMD_PAUSE_MODE in CMD_REG, it also needs to reset
internal state machine to let cs inactive at once.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Actually, spi_master_put() after spi_alloc_master() must _not_ be followed
by kfree(). The memory is already freed with the call to spi_master_put()
through spi_master_class, which registers a release function. Calling both
spi_master_put() and kfree() results in often nasty (and delayed) crashes
elsewhere in the kernel, often in the networking stack.
This reverts commit eb4af0f534.
Link to patch and concerns: https://lkml.org/lkml/2012/9/3/269
or
http://lkml.iu.edu/hypermail/linux/kernel/1209.0/00790.html
Alexey Klimov: This revert becomes valid after
94c69f765f when spi-imx.c
has been fixed and there is no need to call kfree() so comment
for spi_alloc_master() should be fixed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On Intel Baytrail, there is case when interrupt handler get called, no SPI
message is captured. The RX FIFO is indeed empty when RX timeout pending
interrupt (SSSR_TINT) happens.
Use the BIOS version where both HSUART and SPI are on the same IRQ. Both
drivers are using IRQF_SHARED when calling the request_irq function. When
running two separate and independent SPI and HSUART application that
generate data traffic on both components, user will see messages like
below on the console:
pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler
This commit will fix this by first checking Receiver Time-out Interrupt,
if it is disabled, ignore the request and return without servicing.
Signed-off-by: Tan, Jui Nee <jui.nee.tan@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch removes clk_disable_unprepare() in mtk_spi_remove().
clk_disable_prepare/unprepare must be balance, spi-clk is disabled
in mtk_spi_probe, so not needs to disable again.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The upper limit of Tx/Rx FIFO size is 64 word by the
specification of H/W. This patch corrects to 64 word from 256 word.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add SPI Master controller driver for the SPI interface on XLP8XX,
XLP3XX, XLP2XX, XLP9XX and XLP5XX family of Netlogic XLP MIPS64 processors.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM and use autosuspend instead of suspending the
SPI controller after each transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that most cleanup is done automatically the remove functions
can be significantly simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrate fsl-espi and fsl-spi to using the managed devm_ functions
for resource handling. This simplifies the cleanup.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
enable pause interrupt should use SPI_CMD_PAUSE_IE MACRO,
so fix it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows drivers for devices connected via SPI to check if the
controller supports a given bits_per_word value during setup.
Currently any BPW value is accepted durings setup, and transfers
are rejected later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces *_time name in mtk_spi_prepare_transfer().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch replaces int with u32, deletes TAB, and defines
MTK_SPI_PAUSE_INT_STATUS marco.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mediatek spi driver uses readl/writel, so add linux/io.h,
even so it's implicitly imported by spi/spi.h
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for dual read/writes on spi-bcm63xx-hsspi. This has been
tested with a s25fl129p1 dual read capable spi flash, with a nice speed
improvement:
serial read:
root@OpenWrt:/# time dd if=/dev/mtd4 of=/dev/null bs=8192
2032+0 records in
2032+0 records out
real 0m 4.39s
user 0m 0.00s
sys 0m 1.55s
dual read:
root@OpenWrt:/# time dd if=/dev/mtd4 of=/dev/null bs=8192
2032+0 records in
2032+0 records out
real 0m 3.09s
user 0m 0.00s
sys 0m 1.56s
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit
accesses") changed all 16bit accesses in the DW_apb_ssi driver to 32bit.
This, unfortunately, breaks data register access on picoXcell, where the
DW IP needs data register accesses to be word accesses (all other
accesses appear to be OK).
This change introduces a new master variable to allow interface drivers
to specify that 16bit data transfer I/O is required. This change also
introduces the ability to set this variable via device tree bindings in
the MMIO interface driver. Both the core and the MMIO interface driver
default to the current 32bit behaviour.
Before this change, on a picoXcell pc3x3:
spi_master spi32766: interrupt_transfer: fifo overrun/underrun
m25p80 spi32766.0: error -5 reading 9f
m25p80: probe of spi32766.0 failed with error -5
After this change:
m25p80 spi32766.0: m25p40 (512 Kbytes)
Fixes: dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit accesses")
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a slave appears with no maximum transfer speed specified fall back to
using the maximum for the master instead. It's questionable if we
should let slaves do this but let's be defensive.
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes SPI_CMD_*_OFFSET defines, and uses the BIT(x)
defines instead.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TX_ENDIAN/RX_ENDIAN bits define whether to reverse the endian
order of the data DMA from/to memory. The endian order should
keep the same with cpu endian.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TI QSPI has four 32 bit data regsiters which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with spi-nor flash,
make use of all the four registers so that 16 bytes can be transferred
in one go. This reduces number of register writes and Word Complete
interrupts for a given transfer message size, thereby increasing the
write performance.
Without this patch the raw flash write speed is ~100KB/s, with this
patch the write speed increases to ~400 kB/s on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clock in prepare_hardware/unprepare_hardware is redundant
with pm_runtime, so remove them.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACK of an inexistent IRQ can trigger an spurious IRQ that breaks the
txrx logic. This has been observed on axi_quad_spi:3.2 core.
This patch only ACKs IRQs that have not been Acknowledge jet.
Reported-by: Edward Kigwana <ekigwana@scires.com>
Tested-by: Edward Kigwana <ekigwana@scires.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
writel() already does a cpu_to_le32 conversion, so
remove cpu_to_le32().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once the module process a transfer in irq mode, the next poll transfer
will not work because the transmitter is left in inhibited state.
Fixes: 22417352f6 (Use polling mode on small transfers)
Reported-by: Edward Kigwana <ekigwana@scires.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Description:
On Armada 38x, the device SPI interface supports frequencies of up to
50 MHz. However, due to this erratum, when the device core clock is
250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1, there might occur data corruption on reads from the SPI
device.
Workaround:
Work in one of the following configurations:
1. Set CPOL=CPHA=0 in "SPI Interface Configuration Register".
2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1 Register"
before setting the interface.
[gregory.clement@free-electrons.com}: port to v4.2-rc, use
is_errata_50mhz_ac instead of using a new ARMADA_380_SPI spi type.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch fixes endian warnings detected by sparse:
- sparse: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] val
got restricted __le32 [usertype] <noident>
- sparse: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] val
got restricted __le32 [usertype] <noident>
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extra space and make the alias matches driver name.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-img-spfi.c: In function 'img_spfi_setup':
drivers/spi/spi-img-spfi.c:446: warning: 'ret' may be used
uninitialized in this function.
Fixes: commit b03ba9e314 ("spi: img-spfi: fix multiple calls to request gpio")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Remove null_dma_buf variable and extra allocation for it. It is not needed
since commit 6356437e65 ("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spfi_setup may be called many times by the spi framework, but
gpio_request_one can only be called once without freeing, repeatedly
calling gpio_request_one will cause an error to be thrown, which
causes the request to spi_setup to be marked as failed.
We can have a per-spi_device flag that indicates whether or not the
gpio has been requested. If the gpio has already been requested use
gpio_direction_output to set the direction of the gpio.
Fixes: 8c2c8c03cd ("spi: img-spfi: Control CS lines with GPIO")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Fix inconsistent indenting in spidev_open, no functional change.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These became unused by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Major difference in LPSS SPI between Intel Sunrisepoint PCH and earlier
platforms is an integrated DMA (iDMA) engine. iDMA is an IP that is private
for each LPSS host controller (UART/SPI/I2C). Other differences are private
register space offset, a few private registers that are in different
location and FIFO thresholds.
Intel Sunrisepoint LPSS SPI and iDMA devices are probed and registered in
MFD layer as platform devices. Here these compound devices are detected by
matching against known PCI IDs. This allows us to share
pxa2xx_spi_acpi_get_pdata() for setting up the platform data instead of
duplicating it in MFD part.
This patch adds configuration for Intel Sunrisepoint LPSS SPI, above
detection and DMA filter function that picks the DMA channel only from an
associated iDMA block.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This resulted in the use of polling mode when other approaches
(dma or interrupts) would have been more appropriate.
Happened for transfers longer than 477 bytes.
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch fixes a regression introduced by commit 232a5adc51 ("spi:
bitbang: only toggle bitchanges"). The attempt to optimize writes of
consecutive bit patterns broke most of the combinations of word size
and SPI modes due to selecting the wrong bit as the MSB value.
Fixes: 232a5adc51 (spi: bitbang: only toggle bitchanges)
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Calling spfi_wait_all_done is not required if the transfer has timed
out before all data is transferred.
spfi_wait_all_done polls for Alldone interrupt which is triggered to
mark the transfer as complete and to indicate it is now safe to issue
a new transfer.
Fixes: 8c2c8c0 ("spi: img-spfi: Control CS lines with GPIO")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Printing the FIFO depth does not add much noise in the log and can be useful
for debugging transfer issues.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For spi without dma channel and use can_dma(), it can
use master->dev for struct device.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit ddcad7e906 omap2_mcspi_set_cs() is called without
runtime power management requested. This patch fixes the problem by
requesting runtime power management in omap2_mcspi_set_cs().
Reported-By: Pali Rohár <pali.rohar@gmail.com>
Fixes: ddcad7e906 (spi: omap2-mcspi: Fix native cs with new set_cs)
Tested-By: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the pre-scaler limit is incorrect. The value differs slightly
for various devices so a single value can't be used. Using the compatible
field select the correct pre-scaler limit.
Add new compatible field value for Keystone devices to support their
unique pre-scaler limit value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Within davinci_spi_get_prescale() the prescale has two meanings. First one
being the calculated prescale value and then at the end translates it to the
prescale value that will be written to the SPI register.
At first glance this can be confusing especially when comparing the minimum
prescale value against what is seen in the TRM.
To simplify things make it clear that the calculated prescale value will always
be based on the value that will be written into the SPI register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes several warnings like:
drivers/spi/spi-mpc512x-psc.c: In function 'mpc512x_psc_spi_prep_xfer_hw':
arch/powerpc/include/asm/io.h:163:2: warning: '__ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
introduced in commit 8bf960985d for some build configurations.
Fixes: 8bf960985d ("spi: mpc512x-psc: add support for Freescale MPC5125")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register layout of the PSC devices differ between MPC5121 and
MPC5125, but the registers are named nearly identical and their purpose
is similar enough ("freescale identical") such that substituting
mpc52xx_psc by mpc5125_psc is nearly enough to make the driver work on
MPC5125. To keep supporting MPC5121 this patch introduces a cpp
macro to select the right struct that defines the register layout.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Remove the include here because this is a
provider driver.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a missing break statement here so selecting both only selects
upper.
Fixes: dfe11a11d5 ('spi: Add support for Zynq Ultrascale+ MPSoC GQSPI controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since spidev is no more allowed to use in DT and is really loudly warned about
it I'd like to add this compatible value.
(Geert Uytterhoeven wrote: "Add the compatible value for your device to the
spidev_dt_ids[] array in drivers/spi/spidev.c.")
Signed-off-by: Mark Brown <broonie@kernel.org>
per spi-master statistics accessible as:
/sys/class/spi_master/spi*/statistics/*
per spi-device statistics accessible via:
/sys/class/spi_master/spi*/spi*.*/statistics/*
The following statistics are exposed as separate "files" inside
these directories:
* messages number of spi_messages
* transfers number of spi_transfers
* bytes number of bytes transferred
* bytes_rx number of bytes transmitted
* bytes_tx number of bytes received
* errors number of errors encounterd
* timedout number of messages that have timed out
* spi_async number of spi_messages submitted using spi_async
* spi_sync number of spi_messages submitted using spi_sync
* spi_sync_immediate number of spi_messages submitted using spi_sync,
that are handled immediately without a context switch
to the spi_pump worker-thread
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Memory for struct rockchip_spi is allocated by spi_alloc_master()
using kzalloc() so it doesn't need to be set to 0 one more time.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Memory for this struct is allocated by spi_alloc_master() using
kzalloc() so it doesn't need to be set to 0 one more time.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_map_buf() processes mapping of vmalloc-ed buffers in a special way,
making mapping of every page separately. However, if the buffer is not
aligned to page boundary (e.g. sub-array in a vmalloc-ed array), it
fills the scatter table with page-size unaligned pieces, that cross
page boundaries. This is incorrect and can, for example, cause memory
corruption and various crashes when working with ubifs on spi-nor chips
(though those drivers are themselves buggy in that they should be
providing DMAable memory to the SPI framework).
Fix this by using proper scatter table size and intra-page buffer lengths,
so that the whole buffer splits into separate scatter table entries on
page boundaries.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maximum speed supported by spfi is limited to 1/4 of the spfi clock.
But in some SoCs the maximum speed supported by the spfi block can
be limited to less than 1/4 of the spfi clock. In such cases we have
to define the limit in the device tree so that the driver can pick
it up.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
qspi_set_send_trigger() returns an unsigned value, so make it return
"unsigned int".
Update the loop variables qspi_trigger_transfer_out_int() to match the
above.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just use "ret" instead, for consistency with other similar functions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
