The value used for boot_params in h7201-eval.c is nonsensical, given that
PLAT_PHYS_OFFSET is defined to 0x40000000. Left unchanged to purposely
break the build to get its maintainer's attention.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The boot_params member of the mdesc structure is used to provide a
default physical address for the ATAG list. Since this value is fixed
at compile time and sometimes based on constants such as ARCH_PHYS_OFFSET,
it gets in the way of runtime PHYS_OFFSET and CONFIG_ARM_PATCH_PHYS_VIRT
usage.
Let's introduce atag_offset which should contains only the relative
offset from PHYS_OFFSET instead of an absolute value, in preparation
to move all instance of boot_params over to it.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
Instead of setting up a match interrupt for 'current_time + delta'
on ->set_next_event(), program timer 0 to count down from 'delta - 1'
and trigger an interrupt when it reaches zero.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently, arch-mmp/time.c uses timer 0 both as a clocksource timer
and as a clockevent timer, the latter by setting up a comparator
interrupt to match on 'current_time + delta'. This is problematic
if delta is small enough, as that can lead to 'current_time + delta'
already being in the past when comparator setup has finished, leading
to the requested event not triggering.
As there is also a silicon issue that requires stopping a timer's
counter while writing to one of its match registers, we'll switch to
using two separate timers -- timer 0 as clockevent timer, which we'll
start and stop on every invocation of ->set_next_event(), and timer 1
as clocksource timer, which will be free-running.
This first patch enables timer 1 on boot, so that we can use it as
clocksource timer.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Move definitions from mfp-gplugd.h to mfp-pxa168.h as they aren't
gplugD specific.
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
The PCI nanoengine driver in the SA1100 machine probably has not
been building for some time. It probably dragged hardware.h
in implicitly and now it doesn't anymore. After this an SA1100
build selecting all system variants will build successfully.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.
This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
