As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device probe method e1000_probe calls e1000_init_eeprom_params
itself so there's no reason to call it again from e1000_do_write_eeprom
or e1000_do_read_eeprom.
The sentence above assumes that e1000_init_eeprom_params is effective.
e1000_init_eeprom_params depends mostly on hw->mac_type and e1000_probe
bails out early if it can't set mac_type (see e1000_init_hw_struct, then
e1000_set_mac_type), qed.
Btw, if effective, the removed paths would had been deadlock prone when
e1000_eeprom_spi was set:
-> e1000_write_eeprom (takes e1000_eeprom_lock)
-> e1000_do_write_eeprom
-> e1000_init_eeprom_params
-> e1000_read_eeprom (takes e1000_eeprom_lock)
(same narrative with e1000_read_eeprom -> e1000_do_read_eeprom etc.)
As a final note, the candidate deadlock above can't happen in e1000_probe
due to the way eeprom->word_size is set / tested.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to rmb with dma_rmb in the case where we want to
order all follow-on descriptor reads after the check for the descriptor
status bit.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
[...]
Call Trace:
[<ffffffff81195445>] put_page+0x55/0x60
[<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
[<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
[<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
[<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
[<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
[<ffffffff81647050>] dev_set_mtu+0xa0/0x140
[<ffffffff81664218>] do_setlink+0x218/0xac0
[<ffffffff814459e9>] ? nla_parse+0xb9/0x120
[<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
[<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
[<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260
By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers. The allocator is set back to a sane value in
e1000_configure_rx.
Fixes: edbbb3ca10 ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't update Tx tail descriptor if we queue hasn't been stopped and
we know at least one more skb will be sent right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To be future-proof and for better readability the time comparisons are
modified to use time_after_eq() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VMWare's e1000 implementation does not seem to support unicast filtering.
This can be observed by configuring a macvlan interface on eth0 in a VM in
VMWare Fusion 5.0.5, and trying to use that interface instead of eth0.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
and remove *page, its only used for Rx.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000 uses the same metadata struct for Rx and Tx. But Tx and Rx have
different requirements.
For Rx, we only need to store a buffer and a DMA address.
Follow-up patch will remove skb for Rx, bringing rx_buffer_info down
to 16 bytes on x86_64.
[ buffer_info is 48 bytes ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we unmap the DMA range, then copy to new skb.
Change this so we can keep the mapping in case the data is copied.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Its the same in both handlers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
... and make it static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed many errors/warnings and checks in e1000_ethtool.c reported
by checkpatch.pl. Suggestions from Joe Perches and Alexander Duyck
applied as well
Signed-off-by: Krzysztof Majzerowicz-Jaszcz <cristos@vipserv.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This will results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no case skb->len would be 0 or 'negative'.
Remove the check.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the is_broadcast_ether_addr/is_multicast_ether_addr helper functions
from linux/etherdevice.h instead of open coding them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000_hw.c contains a lot of debug messages which print
name of invoked function and contain no new line character
at the end. Remove them as equivalent information can be
nowadays obtained using function tracer.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On e1000_down(), we should ensure every asynchronous work is canceled
before proceeding. Since the watchdog_task can schedule other works
apart from itself, it should be stopped first, but currently it is
stopped after the reset_task. This can result in the following race
leading to the reset_task running after the module unload:
e1000_down_and_stop(): e1000_watchdog():
---------------------- -----------------
cancel_work_sync(reset_task)
schedule_work(reset_task)
cancel_delayed_work_sync(watchdog_task)
The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning
of e1000_down_and_stop() thus ensuring the race is impossible.
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes the following lockdep warning, which is 100%
reproducible on network restart:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0+ #47 Tainted: GF
-------------------------------------------------------
kworker/1:1/27 is trying to acquire lock:
((&(&adapter->watchdog_task)->work)){+.+...}, at: [<ffffffff8108a5b0>] flush_work+0x0/0x70
but task is already holding lock:
(&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&adapter->mutex){+.+...}:
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff816b8cbc>] mutex_lock_nested+0x4c/0x390
[<ffffffffa017233d>] e1000_watchdog+0x7d/0x5b0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
-> #0 ((&(&adapter->watchdog_task)->work)){+.+...}:
[<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff8108a5eb>] flush_work+0x3b/0x70
[<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140
[<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20
[<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000]
[<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000]
[<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&adapter->mutex);
lock((&(&adapter->watchdog_task)->work));
lock(&adapter->mutex);
lock((&(&adapter->watchdog_task)->work));
*** DEADLOCK ***
3 locks held by kworker/1:1/27:
#0: (events){.+.+.+}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510
#1: ((&adapter->reset_task)){+.+...}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510
#2: (&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000]
stack backtrace:
CPU: 1 PID: 27 Comm: kworker/1:1 Tainted: GF 3.12.0+ #47
Hardware name: System manufacturer System Product Name/P5B-VM SE, BIOS 0501 05/31/2007
Workqueue: events e1000_reset_task [e1000]
ffffffff820f6000 ffff88007b9dba98 ffffffff816b54a2 0000000000000002
ffffffff820f5e50 ffff88007b9dbae8 ffffffff810ba936 ffff88007b9dbac8
ffff88007b9dbb48 ffff88007b9d8f00 ffff88007b9d8780 ffff88007b9d8f00
Call Trace:
[<ffffffff816b54a2>] dump_stack+0x49/0x5f
[<ffffffff810ba936>] print_circular_bug+0x216/0x310
[<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff8108a5eb>] flush_work+0x3b/0x70
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140
[<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20
[<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000]
[<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000]
[<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108b906>] ? process_one_work+0x166/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff8108c960>] ? manage_workers+0x2c0/0x2c0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
[<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70
== The issue background ==
The problem occurs, because e1000_down(), which is called under
adapter->mutex by e1000_reset_task(), tries to synchronously cancel
e1000 auxiliary works (reset_task, watchdog_task, phy_info_task,
fifo_stall_task), which take adapter->mutex in their handlers. So the
question is what does adapter->mutex protect there?
The adapter->mutex was introduced by commit 0ef4ee ("e1000: convert to
private mutex from rtnl") as a replacement for rtnl_lock() taken in the
asynchronous handlers. It targeted on fixing a similar lockdep warning
issued when e1000_down() was called under rtnl_lock(), and it fixed it,
but unfortunately it introduced the lockdep warning described above.
Anyway, that said the source of this bug is that the asynchronous works
were made to take rtnl_lock() some time ago, so let's look deeper and
find why it was added there.
The rtnl_lock() was added to asynchronous handlers by commit 338c15
("e1000: fix occasional panic on unload") in order to prevent
asynchronous handlers from execution after the module is unloaded
(e1000_down() is called) as it follows from the comment to the commit:
> Net drivers in general have an issue where timers fired
> by mod_timer or work threads with schedule_work are running
> outside of the rtnl_lock.
>
> With no other lock protection these routines are vulnerable
> to races with driver unload or reset paths.
>
> The longer term solution to this might be a redesign with
> safer locks being taken in the driver to guarantee no
> reentrance, but for now a safe and effective fix is
> to take the rtnl_lock in these routines.
I'm not sure if this locking scheme fixed the problem or just made it
unlikely, although I incline to the latter. Anyway, this was long time
ago when e1000 auxiliary works were implemented as timers scheduling
real work handlers in their routines. The e1000_down() function only
canceled the timers, but left the real handlers running if they were
running, which could result in work execution after module unload.
Today, the e1000 driver uses sane delayed works instead of the pair
timer+work to implement its delayed asynchronous handlers, and the
e1000_down() synchronously cancels all the works so that the problem
that commit 338c15 tried to cope with disappeared, and we don't need any
locks in the handlers any more. Moreover, any locking there can
potentially result in a deadlock.
So, this patch reverts commits 0ef4ee and 338c15.
Fixes: 0ef4eedc2e ("e1000: convert to private mutex from rtnl")
Fixes: 338c15e470 ("e1000: fix occasional panic on unload")
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is based on a similar change made to e1000e support in
commit bb9e44d0d0 ("e1000e: prevent oops when adapter is being closed
and reset simultaneously"). The same issue has also been observed
on the older e1000 cards.
Here, we have increased the RESET_COUNT value to 50 because there are too
many accesses to e1000 nic on stress tests to e1000 nic, it is not enough
to set RESET_COUT 25. Experimentation has shown that it is enough to set
RESET_COUNT 50.
Signed-off-by: yzhu1 <yanjun.zhu@windriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
tx_ring and adapter->tx_ring are already of type "struct
e1000_tx_ring *"
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
After dma_map_single, dma_mapping_error must be called.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed. In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
