Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d4701 ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default tx ring size of 512 causes an extra page to be
allocated for the tx ring with only 1 entry in it. Reduce it to
511. The default rx ring size is also reduced to 511 to use less
memory by default.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx push is supported for small packets to reduce DMA latency. The
following bugs are fixed in this patch:
1. Fix the definition of the push BD which is different from the DMA BD.
2. The push buffer has to be zero padded to the next 64-bit word boundary
or tx checksum won't be correct.
3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD)
so that small tunneled packets are within the threshold.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
20G is not supported by production hardware and only the 40GbaseCR4 standard
is supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off. Autoneg flow control is possible only if autoneg is enabled.
In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.
2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.
3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.
In order to reproduce run on device during active ethernet work:
ifconfig eth0 down
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently our netdevice ops is a one static global variable which
is referenced by all mlx5e netdevice instances. This can be
problematic when different driver instances do not share same
HW capabilities (e.g SRIOV PF and VFs probed to the host).
Now we have two constant global netdevice ops variables, one
for basic netdevice ops and the other with extended SRIOV ops,
on netdevice construction we choose the one suitable for
current device capabilities.
Fixes: 66e49dedad ("net/mlx5e: Add support for SR-IOV ndos")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5e_select_queue is redundant since num_tc is always 1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The am79c961a.c driver fails to build with clang because of an
unusual inline assembly construct:
drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string
"str%?h %1, [%2] @ NET_RAP\n\t"
The same change has been done a decade ago in arch/arm as of
6a39dd6222 ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for the R-Car gen3 gPTP active in configuration mode,
some call sites of ravb_ptp_{init|stop}() were missed due to an oversight.
Add checks for the R-Car gen2 SoCs around these...
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for the R-Car gen3 gPTP active in configuration mode,
the code setting the CCC.CSEL field was duplicated due to an oversight.
For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this
time is probably ignored due to CCC.GAC bit being already set...
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch detected a suspicious looking bitop condition:
drivers/net/ethernet/cavium/liquidio/lio_main.c:2529
handle_timestamp() warn: suspicious bitop condition
(skb_shinfo(skb)->tx_flags | SKBTX_IN_PROGRESS is always non-zero,
so the logic is definitely not correct. Use & to mask the correct
bit.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit 2dcf75e279 ("net: mvneta: Associate RX queues with
each CPU") all the percpu irq are used and disabled at initialization, so
there is no point to disable them first.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a for_each_* loop in which we just call the
smp_call_function_single macro, it is more simple to directly use the
on_each_cpu macro. Moreover, this macro ensures that the calls will be
done all at once.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing to the management of multiple RX queue, the
mvneta_percpu_elect function was broken. The use of the modulo can lead
to elect the wrong cpu. For example with rxq_def=2, if the CPU 2 goes
offline and then online, we ended with the third RX queue activated in
the same time on CPU 0 and CPU2, which lead to a kernel crash.
With this fix, we don't try to get "the closer" CPU if the default CPU is
gone, now we just use CPU 0 which always be there. Thanks to this, the
code becomes more readable, easier to maintain and more predicable.
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the for_each_present in on_each_cpu, instead of
applying on the present cpus it will be applied only on the online cpus.
This fix a bug reported on
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173.
Using the macro on_each_cpu (instead of a for_each_* loop) also ensures
that all the calls will be done all at once.
Fixes: f864288544 ("net: mvneta: Statically assign queues to CPUs")
Reported-by: Stefan Roese <stefan.roese@gmail.com>
Suggested-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are typos in setting RTL8168H hardware parameters. If system install
another version driver that may cuase system hang.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
position p,q;
@@
e@q = kzalloc(...);
if@p (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>
This function may also return -1 after calling mpp2_prs_tcam_port_map_get.
So that the function consistently returns meaningful error values on
failure, the -1 is changed to -EINVAL.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of vmalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
identifier l1;
position p,q;
@@
e@q = vmalloc(...);
if@p (e == NULL) {
...
goto l1;
}
l1:
...
return -1
+ -ENOMEM
;
//</smpl
The single call site of the containing function checks whether the
returned value is -1, so this check is changed as well. The single call
site of this call site, however, only checks whether the value is not 0,
so no further change was required.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware posts the devcmd result in result ring. In case of timeout, driver
does not increment the current result pointer and firmware could post the
result after timeout has occurred. During next devcmd, driver would be
reading the result of previous devcmd.
Fix this by incrementing result even in case of timeout.
Fixes: 373fb0873d ("enic: add devcmd2")
Signed-off-by: Sandeep Pillai <sanpilla@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.
tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.
This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.
v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware reset is currently done after phy_start() is called,
leading to a race where we can lose the link status if the phy state
machine calls dwceqos_adjust_link() before we reset the MAC registers.
Acked-by: Lars Persson <larper@axis.com>
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nb8800_poll() function initializes the 'next' variable in the
loop looking for new input data. We know this will be called at
least once because 'budget' is a guaranteed to be a positive number
when we enter the function, but the compiler doesn't know that
and warns when the variable is used later:
drivers/net/ethernet/aurora/nb8800.c: In function 'nb8800_poll':
drivers/net/ethernet/aurora/nb8800.c:350:21: warning: 'next' may be used uninitialized in this function [-Wmaybe-uninitialized]
Changing the 'while() {}' loop to 'do {} while()' makes it obvious
to the compiler what is going on so it no longer warns.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PCI_MSI is disabled, we get warnings about unused functions
in the vxge driver:
drivers/net/ethernet/neterion/vxge/vxge-main.c:2121:13: warning: 'adaptive_coalesce_tx_interrupts' defined but not used [-Wunused-function]
drivers/net/ethernet/neterion/vxge/vxge-main.c:2149:13: warning: 'adaptive_coalesce_rx_interrupts' defined but not used [-Wunused-function]
We could add another #ifdef here, but it's nicer to avoid those warnings
for good by converting the existing #ifdef to if(IS_ENABLED()), which has
the same effect but provides better compile-time coverage in general,
and lets the compiler understand better when the function is intentionally
unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver depends on BCMA_HOST_SOC, which is only used
when CONFIG_BCMA is enabled. However, it is a bool option and can
be set when CONFIG_BCMA=m, and then bgmac can be built-in, leading
to an obvious link error:
drivers/built-in.o: In function `bgmac_init':
:(.init.text+0x7f2c): undefined reference to `__bcma_driver_register'
drivers/built-in.o: In function `bgmac_exit':
:(.exit.text+0x110a): undefined reference to `bcma_driver_unregister'
To avoid this case, we need to depend on both BCMA and BCMA_SOC,
as this patch does. I'm also trying to make the dependency more
readable by splitting it into three lines, and adding a COMPILE_TEST
alternative so we can test-build it in all configurations that
support BCMA.
The added dependency on FIXED_PHY addresses a related issue where
we cannot call fixed_phy_register() when CONFIG_FIXED_PHY=m and
CONFIG_BGMAC=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the hp100 ethernet driver causes warnings when both the PCI
and EISA drivers are disabled:
ethernet/hp/hp100.c: In function 'hp100_module_init':
ethernet/hp/hp100.c:3047:2: warning: label 'out3' defined but not used [-Wunused-label]
ethernet/hp/hp100.c: At top level:
ethernet/hp/hp100.c:2828:13: warning: 'cleanup_dev' defined but not used [-Wunused-function]
We can easily avoid the warnings and make the driver look slightly
nicer by removing the #ifdefs that check for the CONFIG_PCI and
CONFIG_EISA, as all the registration functions are designed to
have no effect when the buses are disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The davinci_cpdma mixes up physical addresses as seen from the CPU
and DMA addresses as seen from a DMA master, since it can operate
on both normal memory or an on-chip buffer. If dma_addr_t is
different from phys_addr_t, this means we get a compile-time warning
about the type mismatch:
ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
ethernet/ti/davinci_cpdma.c:182:48: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
pool->cpumap = dma_alloc_coherent(dev, size, &pool->phys,
In file included from ethernet/ti/davinci_cpdma.c:21:0:
dma-mapping.h:398:21: note: expected 'dma_addr_t * {aka long long unsigned int *}' but argument is of type 'phys_addr_t * {aka unsigned int *}'
static inline void *dma_alloc_coherent(struct device *dev, size_t size,
This slightly restructures the code so the address we use for
mapping RAM into a DMA address is always a dma_addr_t, avoiding
the warning. The code is correct even if both types are 32-bit
because the DMA master in this device only supports 32-bit addressing
anyway, independent of the types that are used.
We still assign this value to pool->phys, and that is wrong if
the driver is ever used with an IOMMU, but that value appears to
be never used, so there is no problem really. I've added a couple
of comments about where we do things that are slightly violating
the API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The moxart ethernet driver confuses coherent DMA buffers with
MMIO registers.
moxart_ether.c: In function 'moxart_mac_setup_desc_ring':
moxart_ether.c:146:428: error: passing argument 1 of '__fswab32' makes integer from pointer without a cast [-Werror=int-conversion]
moxart_ether.c:74:39: warning: incorrect type in argument 3 (different address spaces)
moxart_ether.c:74:39: expected void *cpu_addr
moxart_ether.c:74:39: got void [noderef] <asn:2>*tx_desc_base
This leaves the basic logic alone and uses normal pointers for
the virtual address of the descriptor. As we cannot use readl/writel
to access them, we also introduce our own moxart_desc_read
moxart_desc_write helpers that perform the same endianess swap
as the original code, but without the address space conversion.
The barriers are made explicit here where needed: Even in the worst-case
scenario, we just have to use a rmb() after checking ownership so
we don't read any input data before we are sure it is value, and we
use wmb() before transferring ownership back to the device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring index j is not wrapped properly at the end of the ring, causing
it to reference pointers past the end of the ring. For proper loop
termination and to access the ring properly, we need to increment j and
mask it before referencing the ring entry.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware counter is misleading as it counts dropped packets that
don't match the hardware filters for unicast/broadcast/multicast. We
will still report this counter in ethtool -S for diagnostics purposes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use completion ring for ring free response from firmware. The response
will be the last entry in the ring and we can free the ring after getting
the response. This will guarantee no spurious DMA to freed memory.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the driver to use ns_to_timespec64() to keep consistency
with timespec64_to_ns() instead of open coding the same logic.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.
However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.
Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.
Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.
Fixes: 03bf0c2812 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in txq_put_data() would use txq->tx_curr_desc to index the
tso_hdrs/tso_hdrs_dma buffers, for less than 8 bytes unaligned
fragments, which is already moved to the next descriptor at the
beginning of the function.
If that fragment was the last of the the skb, the next skb would use
that same space to place the ip headers, overwritting that small
fragment data.
Fixes: 91986fd3d3 (net: mv643xx_eth: Ensure proper data alignment in TSO TX path)
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Reviewed-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_lane, tx_lane and module fields in the PMLP register don't have
an additional offset besides the base one (0x04), so set it to 0x00.
Fixes: 4ec14b7634 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the FDB we can't compare the actual pointers of the ports
structs, as it's possible the struct represents a vPort instead of the
underlying physical port.
Solve this by comparing the local port number instead, as it's shared
between the physical ports and all the vPorts on top of him.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB records can only point to LAG devices or VLAN devices configured
on top of them. Therefore, when dumping the FDB we shouldn't associate
these records with the underlying physical ports.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
