intel_enable_rc6() is used to check if we can compute the RC6 residency
in the sysfs code. Disable this for platforms older than Ironlake.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Put the comment a bit closer to the actual write (Paulo Zanoni)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix space before tab.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also wait for that blank on other platforms but the w/a doesn't
apply there. Not an issue at all.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we have the following interrupt enabling sequence:
1. irq preinstall hook
2. enabling the interrupt handler and calling irq postinstall hook
3. enable rps interrupts from the async work
And the folliwing disable sequence:
1. disabling the interrupt handler and calling the uninstall hook
2. disabling the rps interrupt
Since the postinstall hook now always sets up PMIIR, PMIER and PMIMR
to known-good states there no way for an interrupt to sneak in in the
enable sequence, so we can reinstate the WARN lost in
commit eda63ffb90
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:26 2013 -0700
drm/i915: Add PM regs to pre/post install
Note that there's some room for future cleanups since most of the
interrupt register clearing in the disable function is rather
redundant. But that's better done in follow-up patches, if at all.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VECS enabling required some changes to how rps interrupts are
enabled/disabled since VECS interrupts are handling with the PM
interrupt registers.
But now that the pre/postinstall sequences is identical for all
platforms with rps support (snb, ivb, hsw, vlv) we can also use the
exact same sequence to actually enable the rps interrupts. Strictly
speaking using spinlocks is overkill on snb/ivb & vlv since they have
no VECS ring, but imo that's more than made up by the common code.
Hence this just unifies the vlv code with the snb-hsw code which
matched exactly before the VECS enabling. See
commit eda63ffb90
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:26 2013 -0700
drm/i915: Add PM regs to pre/post install
and
commit 4848405cce
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:27 2013 -0700
drm/i915: make PM interrupt writes non-destructive
for why the gen6 code (shared between snb, ivb and hsw) needed to be
changed originally.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again extract a common helper. For the postinstall hook things are a
bit more complicated since we have more cases on ilk-hsw/vlv here.
But since vlv was clearly broken by failing to initialize
dev_priv->gt_irq_mask correctly the shared code is clearly justified.
Also kill the PMIER setting in the async rps enable work. I should
have been save, but also clearly looked rather fragile. PMIER setup is
now all down in the irq pre/postinstall hooks.
With this we now have the usual interrupt register sequence for GT/PM
irq registers:
- IER is setup once with all the interrupts we ever need in the
postinstall hook and never touched again. Exceptions are SDEIER,
which is touched in the preinstall hook (when the irq handler isn't
enabled) and then only from the irq handler. And DEIER/VLV_IER with
is used in the irq handler but also written to once in the
postinstall hook. But since that write is essentially what enables
the interrupt and we should always have MSI interrupts we should be
save. In case we ever have non-MSI interrupts we'd be screwed.
- IIR is cleared in the postinstall hook before we enable/unmask the
respective interrupt sources. Hence we can't steal an interrupt
event an accidentally trigger the spurious interrupt logic in the
core kernel. Note that after some discussion with Ben Widawsky we
think that we actually should clear the IIR registers in the
preinstall hook. But doing that is a much larger patch series.
- IMR regs are (usually) all masked off. Those are the only regs
changed at runtime, which is all protected by dev_priv->irq_lock.
This unification also kills the cargo-culted read-modify-write PM
register setup for VECS. Interrupt setup is done without userspace
being able to interfere, so we better know what values we want to put
into those registers. RMW cycles otoh are really good at papering over
races, until stuff magically blows up and no one has a clue why.
v2: Touch the gen6+ PM interrupt registers only on gen6+.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a comment to explain why the l3 parity interrupt is
special.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the rps interrupt locking isn't clearly separated (at elast
conceptually) from all the other interrupt locking having a different
lock stopped making sense: It protects much more than just the rps
workqueue it started out with. But with the addition of VECS the
separation started to blurr and resulted in some more complex locking
for the ring interrupt refcount.
With this we can (again) unifiy the ringbuffer irq refcounts without
causing a massive confusion, but that's for the next patch.
v2: Explain better why the rps.lock once made sense and why no longer,
requested by Ben.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).
It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.
v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)
v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A magic -1 is a obscure, especially since it's actually passed as an
unsigned, so depends upon the magic sign extension rules in C. This has
been added in
commit 3727d55e4d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed May 8 10:45:14 2013 -0700
drm/i915: allow stolen, pre-allocated objects to avoid GTT allocation v2
Use a proper #define instead. Spotted while reviewing Ben's
drm_mm_create_block changes.
v2: Cast the constant to u32 since otherwise we again have a type
mismatch. Suggested by Chris Wilson.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use wait_for() instead of the open coded loop to avoid spreading the
same old timeout related bugs.
This changes the loop to use msleep(1) instead of udelay(10) when the
Punit had not yet completed the frequency change. In practice that
doesn't seem to hurt performance as the Punit appears to be ready pretty
much always.
Also give the status bit a name, instead of using the magic number 1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict with Damien's FBC_CHIP_DEFAULT no fbc
reason.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A genuine 'static' omission and 2 other warnings triggered by not
including the header where those functions where defined.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When running on my snb machine, recent kernels display successively:
[drm:intel_update_fbc], fbc set to per-chip default
[drm:intel_update_fbc], fbc disabled per module param
But no module param is set. This happens because the check for the
module parameter uses a variable that has been overridden inside the
"per-chip default" code.
Fix up the logic and add another reason for the FBC to the be disabled.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function has no user outside of intel_pm.c.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently print a DRM_DEBUG_KMS message on the happy path and don't
print anything on the "failed to allocate" path. On some desktop
environments (e.g., Unity) I see the "scheduling delayed FBC enable"
thousands and thousands of times on my dmesg.
So kill the useless message for the happy case, saving a lot of dmesg
space, and properly signal the "kzalloc fail" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's little point in increasing the GPU frequency from the delayed
rps work on VLV. Now when the GPU is idle, the GPU frequency actually
keeps dropping gradually until it hits the minimum, whereas previously
it just ping-ponged constantly between RPe and RPe-1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs.
Reading it always returns zero from what I can tell, and eliminating
it doesn't seem to make any difference to the behaviour of the system.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that even though Punit reports the frequency change to have
been completed, it still reports the old frequency in the status
register for some time.
So rather than polling for Punit to complete the frequency change after
each request, poll before. This gets rid of the spurious "Punit overrode
GPU freq" messages.
This also lets us continue working while Punit is performing the actual
frequency change. As a result, openarena demo088-test1 timedemo average
fps is increased by ~5 fps, and the slowest frame duration is reduced
by ~25%.
The sysfs cur_freq file always reads the current frequency from Punit
anyway, so having rps.cur_delay be slightly off at times doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print both the MHz value and raw register value for rps stuff.
Also kill a somewhat pointless local 'rpe' variable and just use
dev_priv->rps.rpe_delay.
While at it clean up the caps in "GPU" and "Punit" debug messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to apply WaForceL3Serialization:vlv twice.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the code to disable trickle feed for all primary planes into a
separate function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable trickle feed in all the (relevant) clock gating functions,
except ironlake_init_clock_gating(). Copy paste the same code there as
well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec, trickle feed should be disabled for BW and
mobile CL. Those constraints seem to match all of our gen4 chipsets.
Trickle feed is disabled via the MI_ARB_STATE register instead of
per plane controls on gen4.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs say that the trickle feed disable bit is present (for primary
planes only, not video sprites) on CTG, and that it must be set
for ELK. Just set it for all g4x chipsets.
v2: Do it in init_clock_gating too
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell Display audio depends on power well in graphic side, it should
request power well before use it and release power well after use.
I915 will not shutdown power well if it detects audio is using.
This patch protects display audio crash for Intel Haswell C3 stepping board.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CTG/ILK/SNB/IVB support 4kx2k surfaces. HSW supports 4kx4k, but
without proper front buffer invalidation on the last 2k lines, so
don't enable FBC on these cases for now.
v2: Use gen >= 5, not gen > 4 (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LP watermark registers don't exist on VLV, so don't touch them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment, these values are wiped out anyway by the rps
enable/disable. That will be changed in the next patch though.
v2: Add post install setup to address issue found by Damien in the next
patch.
replaced
WARN_ON(dev_priv->rps.pm_iir != 0);
with rps.pm_iir = 0;
With the v2 of this patch and the deferred pm enabling (which changed
since the original patches) we're now able to get PM interrupts before
we've brought up enabled rps. At this point in boot, we don't want to do
anything about it, so we simply ignore it. Since writing the original
assertion, the code has changed quite a bit, and I believe removing this
assertion is perfectly safe.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: I don't agree with the justification to drop the WARN and
added a FIXME to that effect.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we compute the results for both 1/2 and 5/6 partitioning and then
use hsw_find_best_result to choose which one to use.
With this patch, Haswell watermarks support should be in good shape.
The only improvement we're missing is the case where the primary plane
is disabled: we always assume it's enabled, so we take it into
consideration when calculating the watermarks.
v2: - Check the latency when finding the best result
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously only setting the WM_PIPE registers, now we are
setting the LP watermark registers. This should allow deeper PC
states, resulting in power savings.
We're only using 1/2 data buffer partitioning for now.
v2: Merge both hsw_compute_pri_wm_* functions (Ville)
v3: - Simplify hsw_compute_wm_results (Ville)
- Rebase due to changes on the previous patch
v4: Unconfuse wm_lp/level (Ville)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously calling sandybridge_update_wm on HSW, but the SNB
function didn't really match the HSW specification, so we were just
writing the wrong values.
With this patch, the haswell_update_wm function will set the correct
values for the WM_PIPE registers, but it will still keep all the LP
watermarks disabled.
The patch may look a little bit over-complicated for now, but it's
because much of the infrastructure for setting the LP watermarks is
already in place, so we won't have too much code churn on the patch
that sets the LP watermarks.
v2: - Fix pixel_rate on panel fitter case (Ville)
- Try to not overflow (Ville)
- Remove useless variable (Ville)
- Fix p->pri_horiz_pixels (Paulo)
v3: - Fix rounding errors on hsw_wm_method2 (Ville)
v4: - Fix memcmp bug (Paulo)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, whenever we change the sprites we need to completely
recalculate all the watermarks, because the sprites are one of the
parameters to the LP watermarks, so a change on the sprites may
trigger a change on which LP levels are enabled.
So on this commit we store all the parameters we need to store for
proper recalculation of the Haswell WMs and then call
haswell_update_wm.
Notice that for now our haswell_update_wm function is not really using
these parameters we're storing, but on the next commits we'll use
these parameters.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we want to call it from the "sprite disable" paths, since on
Haswell we need to update the sprite watermarks when we disable
sprites.
For now, all this patch does is to add the "enable" argument and call
intel_update_sprite_watermarks from inside ivb_disable_plane. This
shouldn't change how the code behaves because on
sandybridge_update_sprite_wm we just ignore the "!enable" case. The
patches that implement Haswell watermarks will make use of the changes
introduced by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never check the return values, and there's not much we could do on
errors anyway. Just simplify the signatures. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename all VLV IOSF sideband register accessor functions to
vlv_<port>_{read,write}. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Group both the HSW/LPT SBI interface and VLV IOSF sideband register
accessor functions into a new file. No functional changes.
v2: also move intel_sbi_{read,write} (Daniel)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 1544d9d573 added a workaround
inside haswell_init_clock_gating and mentioned it is "a workaround for
early silicon revisions and should be removed later". This workaround
is documented in bit 31 of PRI_CTL. I asked Arthur and he mentioned
that setting FORCE_ARB_IDLE_PLANES replaces that workaround for the
newer machines. So use the new one.
Also notice that there's still another workaround for PRI_CTL that
involves WM_DBG, but it's not the one we're reverting. And notice that
we were previously setting WM_DBG_DISALLOW_MULTIPIPE_LP which disables
the LP watermarks when more than one pipe is used, and we really don't
want this because we need the LP watermarks if we want to reach deeper
PC states.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a comment for the w/a name Ville dug out of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the SNB_READ_WM0_LATENCY macro is not valid anymore because we
have the "New WM0" at 63:56, so the "Old WM0" could maybe be zero if
the new one is not zero.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the "placeholder" comment and set the actual value described by
the specification. We still don't enable IPS, but it won't hurt to
already have the value set here.
While at it, fully set the register value instead of just masking the
values we're changing.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict due to reordered patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the "*8" calculation to the left side so we don't propagate
rounding errors. Also use DIV_ROUND_CLOSEST because that's what the
spec says we need to do.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of mode->crtc_display. The spec says "pipe horizontal
total number of pixels" and the "Haswell Watermark Calculator" tool
uses the "Pipe H Total" instead of "Pipe H Src" as the value.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec says the linetime watermarks must be programmed before
enabling any display low power watermarks, but we're currently
updating the linetime watermarks after we call intel_update_watermarks
(and only at crtc_mode_set, not at crtc_{enable,disable}). So IMHO the
best way guarantee the linetime watermarks will be updated before the
low power watermarks is inside the update_wm function, because it's
the function that enables low power watermarks. And since Haswell is
the only platform that has linetime watermarks, let's completely kill
the "intel_update_linetime_watermarks" abstraction and just use the
intel_update_watermarks abstraction by creating haswell_update_wm.
For now haswell_update_wm is still calling sandybridge_update_wm, but
in the future I plan to implement a function specific to Haswell.
v2: - Rename patch
- Disable LP watermarks before changing linetime WMs (Chris)
- Add a comment explaining that this is just temporary code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should prevent mode set failures on LPT.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Pimp the w/a tag to fit into Damien's new scheme.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
