Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During high throughput it is likely that we receive both: an RX and TX
interrupt. The normal behaviour is that once we enter the ISR the
interrupts are disabled in the IRQ chip and so the ISR is invoked only
once and the interrupt line is disabled once. It will be re-enabled
after napi completes.
With threaded interrupts on the other hand the interrupt the interrupt
is disabled immediately and the ISR is marked for "later". By having TX
and RX interrupt marked pending we invoke them both and disable the
interrupt line twice. The napi callback is still executed once and so
after it completes we remain with interrupts disabled.
The initial patch simply removed the cpsw_{enable|disable}_irq() calls
and it worked well on my AM335X ES1.0 (beagle bone). On ES2.0 (beagle
bone black) it caused an never ending interrupt (even after the mask via
cpsw_intr_disable()) according to Mugunthan V N. Since I don't have the
ES2.0 and no idea what is going on this patch tracks the state of the
irq_disable() call and execute it only when not yet done.
The book keeping is done on the first struct since with dual_emac we can
have two of those and only one interrupt line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
text data bss dec hex filename
15530 92 4 15626 3d0a cpsw.o.before
15478 92 4 15574 3cd6 cpsw.o.after
52 bytes smaller, 13 for each invocation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not clean up properly after leaving. Here is a list:
- Use unregister_netdev(). free_netdev() is good but not enough
- Use the above also on the other ndev in case of dual mac
- Free data.slave_data. The name of the strucre makes it look like
it is platform_data but it is not. It is just a trick!
- Free all irqs. Again: freeing one irq is good start, but freeing all
of them is better.
With this rmmod & modprobe of cpsw seems to work. The remaining issue
is:
|WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0x9c/0xd4()
|sysfs: cannot create duplicate filename '/devices/ocp.2/4a100000.ethernet/4a101000.mdio'
|WARNING: at lib/kobject.c:196 kobject_add_internal+0x1a4/0x1c8()
comming from of_platform_populate() and I am not sure that this belongs
here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If compiled as modules each one of these modules is missing something.
With this patch the modules are loaded on demand and don't taint the
kernel due to license issues.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that we run into OOM during the allocation of the new rx-skb we
don't get one and we have one skb less than we used to have. If this
continues to happen then we end up with no rx-skbs at all.
This patch changes the following:
- if we fail to allocate the new skb, then we treat the currently
completed skb as the new one and so drop the currently received data.
- instead of testing multiple times if the device is gone we rely one
the status field which is set to -ENOSYS in case the channel is going
down and incomplete requests are purged.
cpdma_chan_stop() removes most of the packages with -ENOSYS. The
currently active packet which is removed has the "tear down" bit set.
So if that bit is set, we send ENOSYS as well otherwise we pass the
status bits which are required to figure out which of the two possible
just finished.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp_mask argument is not used in cpdma_chan_submit() and always set
to GFP_KERNEL even in atomic sections. This patch drops it since it is
unused.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_running() reports false before the ->ndo_stop() callback is
called. That means if one executes "ifconfig down" and the system
receives an interrupt before the interrupt source has been disabled we
hang for always for two reasons:
- we never disable the interrupt source because devices claim to be
already inactive and don't feel responsible.
- since the ISR always reports IRQ_HANDLED the line is never deactivated
because it looks like the ISR feels responsible.
This patch changes the logic in the ISR a little:
- If none of the status registers reports an active source (RX or TX,
misc is ignored because it is not actived) we leave with IRQ_NONE.
- the interrupt is deactivated
- The first active network device is taken and napi is scheduled. If
none are active (a small race window between ndo_down() and the
interrupt the) then we leave and should not come back because the
source is off.
There is no need to schedule the second NAPI because both share the
same dma queue.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if during "ifconfig up" we run out of mem we continue regardless how
many skbs we got. In worst case we have zero RX skbs and can't ever
receive further packets since the RX skbs are never reallocated. If
cpdma_chan_submit() fails we even leak the skb.
This patch changes the behavior here:
If we fail to allocate an skb during bring up we don't continue and
report that error. Same goes for errors from cpdma_chan_submit().
While here I changed to __netdev_alloc_skb_ip_align() so GFP_KERNEL can
be used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__cpdma_chan_process() holds the lock with interrupts off (and its
caller as well), same goes for cpdma_ctlr_start(). With interrupts off,
jiffies will not make any progress and if the wait condition never gets
true we wait for ever.
Tgis patch adds a a simple udelay and counting down attempt.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware supports a maximum of 4K FCoE exchanges. In 4-port devices,
or when working in multi-function mode, this resource needs to be distributed
between the various possible FCoE functions.
This information needs to be calculated by bnx2x and propagated into bnx2fc
via cnic. bnx2fc can then use this value to calculate corresponding xid
resources instead of using global constants.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.
Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.
The feature is enabled by default but can be
enabled/disabled by ethtool.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "changed" variable should be a 64 bit type, otherwise it can't store
all the features. The way the code is now the test for whether
NETIF_F_RXCSUM changed is always false and we return immediately.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe, igb and pci.
The ixgbe changes contains a fix to a possible divide by zero by bailing
out of the ixgbe_update_itr() function if the last interrupt timeslice is
zero. In addition, support is added for the new OCP x520 adapter as well
as LX support for 82599 devices. Jacob provides a patch to change
variable wol_supported to wol_enabled to better reflect what the code
is actually doing (i.e. checking if WoL is enabled).
Alex adds SRIOV helper function to pci that will determine if a PF
has any VFs that are currently assigned to a guest.
The remaining 8 patches are against igb and contain the following changes:
* implement SERDES loopback configuration for i210 devices by unsetting
sigdetect bit, so as to fix Ethtool loopback test failure
* add support for the SMBI semaphore for I210/I211 devices
* implement the new generic pci_vfs_assigned helper function (Alex's PCI
helper function)
* display warning when link speed is downgraded due to Smartspeed
* ensure that VLAN hardware filtering remains enabled when the device is
in promiscuous mode and VT mode simultaneously
* cleanup dead code in igb
* bump the driver version
v2: updated the PCI patch to add SRIOV helper function to remove extern
from the declaration of pci_vfs_assigned in pci.h and return 0 if
SR-IOV is disabled which is inline with other PCI SR-IOV functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes id defines from the hardware files that will not be
productized for Linux. These id's were not implemented for support in the
base driver itself, they were just available defines.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82575 manual initialization scripts are not supported on 82580 and
above. Rather than call the function to immediately return, clarify the
code by removing this pointless function call.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using the new bridge FDB interface to allow SR-IOV virtual function
network devices to communicate with SW bridged network devices the
physical function is placed into promiscuous mode and hardware VLAN
filtering is disabled. This defeats the ability to use VLAN tagging
to isolate user networks. When the device is in promiscuous mode and
VT mode simultaneously ensure that VLAN hardware filtering remains
enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current igb driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed. As a result, users suspect that there is something wrong with
NIC. If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make igb notify users that SmartSpeed worked.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the igb driver uses the generic helper
pci_vfs_assigned instead of the igb specific function igb_vfs_are_assigned.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was previously thought that, since I210/I211 are single port devices,
they did not need the SMBI semaphore. This is not the case. Add support for
the SMBI semaphore.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements SERDES loopback configuration for i210 devices by
unsetting sigdetect bit, so as to fix Ethtool loopback test failure. Old
sigdetect code is also simplified to take care of all devices newer than 82580
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a define and WOL support for a new subdevice ID.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds LX support to 82599 devices. This is an alternate patch to
the one suggested by Stefan Behte <s.behte@babiel.com>
In addition this patch includes some cleanups such as:
- removed parenthesis around "x == y ||" lines inside an if statement for
consistency.
- grouped the sx/lx sfp types along with srlr in ixgbe_get_settings() since
they all have the same supported, advertised and port values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Stefan Behte <s.behte@babiel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable wol_supported really is just checking whether it is enabled, rather
than whether it is supported. If it is enabled it will be supported, but this
does not necessarily hold true the other way around. This patch renames the
variable to avoid confusion.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the new OCP x520 adapter. This support
includes WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Protect the code by bailing out of ixgbe_update_itr() when this occurs.
The next call to ixgbe_update_itr will continue to dynamically update ITR.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added identifying strings for 8300 Series of adapters.
o updated PCI_VENDOR_ID_QLOGIC and PCI_DEVICE_ID_824X for 8200
Series adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Interrupt coalescing through ethtool on 83xx adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Read eSwitch statistics from adapter and display them as part
of ethtool statistics.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Disabling PAUSE requires access to EPORT registers,
which may cause a wedge, if EPORT is in reset.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add logs for various failure conditions during channel configuration.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of PCIe Advanced Error Reporting flow, if a fatal PCI error occurs,
the AER driver will cause bnx2x's PCI-core to reset. The driver's PCI error
handlers will in turn restore the PCI configuration space values by calling
`pci_restore_state'.
However, as bnx2x does not save the PCI configuration after restoration,
An additional fatal PCI error will leave the function in an unstable state
until reboot, as the registers in the PCI configuration space will contain
reset values.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exists an `allocation race' between the CNIC and bnx2x drivers,
in which both drivers allocate the same t2 memory while disregarding a possible
previous allocation.
Additionally, due to the current order of memory releases, some of the
ILT memory in the driver is not released correctly when unloading the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improved support for adding/removing vf mac addresses.
This includes the case where HyperVisor forced the address (sampled from
bulletin board), and the case where it did not in which the VF can
configure its own mac address.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when link is configured to auto-negotiate the flow control,
disabling RX/TX pause via ethtool doesn't work.
This fixes the behaviour, advertising asymmetric pause in case either one
is exclusively enabled.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a more robust error handling flow in case of incorrect
behaviour by the FW when passing on GRO aggregations.
Although this should never happen (i.e., this is merely a theoretical fix),
if the bnx2x driver was to receive a GRO from FW with protocol other than
IPv4/IPv6, the driver would falsely claim to have performed partial
checksum and set various incorrect fields in the skb header.
Current behaviour of the bnx2x driver (i.e., print an error) is insufficient.
This patch remedies this by simply preventing the false claims.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a service task to run tasks that needed to be executed periodically.
Currently the only task is a watchdog to catch NIC clock overflow, to make
timestamping accurate.
Will move the statistics task into this framework in a later patch.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the HW MAC layer. This patch adds this call.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device capability for timestamping support and query FW to retrieve it.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses the crummy "| foo" style, putting the
logical operation at the beginning of lines. Then
when the VLAN tag flag bits got changed the operator
ended up at both the end and the beginning of some lines.
Fix the build error by having it uniformly use the operator
at the end of the line.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several call sites were missed when the protocol argument was added to
__vlan_hwaccel_put_tag() in commit
86a9bad3ab ("net: vlan: add protocol
argument to packet tagging functions").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
