This is another attempt for the reduction of the latency at the start
of a USB audio playback stream. The first attempt in the commit
9ce650a75a caused an unexpected regression (a deadlock with pipewire
usage) and was later reverted by the commit 4b820e167b. The devils
are always living in details, of course; the cause of the deadlock was
the call of snd_pcm_period_elapsed() inside prepare_playback_urb()
callback. In the original code, this callback is never called from
the stream lock context as it's driven solely from the URB complete
callback. Along with the movement of the URB submission into the
trigger START, this prepare call may be also executed in the stream
lock context, hence it deadlocked with the another lock in
snd_pcm_period_elapsed(). (Note that this happens only conditionally
with a small period size that matches with the URB buffer length,
which was a reason I overlooked during my tests. Also, the problem
wasn't seen in the capture stream because the capture stream handles
the period-elapsed only at retire callback that isn't executed at the
trigger.)
If it were only about avoiding the deadlock, it'd be possible to use
snd_pcm_period_elapsed_under_stream_lock() as a solution. However, in
general, the period elapsed notification must be sent after the actual
stream start, and replacing the call wouldn't satisfy the pattern.
A better option is to delay the notification after the stream start
procedure finished, instead. In the case of USB framework, one of the
fitting place would be the complete callback of the first URB.
So, as a workaround of the deadlock and the order fixes above, in
addition to the re-applying the changes in the commit 9ce650a75a,
this patch introduces a new flag indicating the delayed period-elapsed
handling and sets it under the possible deadlock condition
(i.e. prepare callback being called before subs->running is set).
Once when the flag is set, the period-elapsed call is handled at a
later URB complete call instead.
As a reference for the original motivation for the low-latency change,
I cite here again:
| USB-audio driver behaves a bit strangely for the playback stream --
| namely, it starts sending silent packets at PCM prepare state while
| the actual data is submitted at first when the trigger START is
| kicked off. This is a workaround for the behavior where URBs are
| processed too quickly at the beginning. That is, if we start
| submitting URBs at trigger START, the first few URBs will be
| immediately completed, and this would result in the immediate
| period-elapsed calls right after the start, which may confuse
| applications.
|
| OTOH, submitting the data after silent URBs would, of course, result
| in a certain delay of the actual data processing, and this is rather
| more serious problem on modern systems, in practice.
|
| This patch tries to revert the workaround and lets the URB
| submission starting at PCM trigger for the playback again. As far
| as I've tested with various backends (native ALSA, PA, JACK, PW), I
| haven't seen any problems (famous last words :)
|
| Note that the capture stream handling needs no such workaround,
| since the capture is driven per received URB.
Link: https://lore.kernel.org/r/4e71531f-4535-fd46-040e-506a3c256bbd@marcan.st
Link: https://lore.kernel.org/r/s5hbl7li0fe.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210707112447.27485-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When 'SB_HW_16' check fails, the error code -ENODEV instead of 0 should be
returned, which is the same as that returned when 'WSS_HW_CMI8330' check
fails.
Fixes: 43bcd973d6 ("[ALSA] Add snd_card_set_generic_dev() call to ISA drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210707074051.2663-1-thunder.leizhen@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA bebob driver has duplicated entries for modalias of
'ieee1394:ven00000AACmo00000002sp0000A02Dver00010001' since entries for
two devices below have the same parameters:
* Acoustic Reality eAR Master One, Eroica, Figaro, and Ciaccona
* TerraTec Aureon 7.1 FireWire
I relied on FFADO revision 737 to add the former entry, on the other hand,
the latter is based on message posted by actual user with information of
sysfs node:
* https://sourceforge.net/p/ffado/mailman/ffado-user/thread/5743F969.2080204%40marcobaldo.ch/
It appears that they have OUI of Terratec Electronic GmbH (0x000aac) and
the same model ID, thus suffice to say that they have something common
in their internals.
Although it's not going to make a big difference, this commit arranges
the entries.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210705111455.63788-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion 15-eh1xxx series uses the HP mainboard 88D0 with ALC287 and needs
the ALC287_FIXUP_HP_GPIO_LED quirk to make the mute led working.
Tested with a HP Pavilion 15-eh1557ng.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210703135416.13151-1-fschaefer.oss@googlemail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 9ce650a75a.
This commit causes watchdog lockups on my machine, and while I have no
idea what the cause is, it bisected right to this commit, and reverting
the change promptly fixes it.
At least occasionally one of the watchdog call traces was
Call Trace:
_raw_spin_lock_irqsave+0x35/0x40
snd_pcm_period_elapsed+0x1b/0xa0 [snd_pcm]
snd_usb_endpoint_start+0x1a0/0x3c0 [snd_usb_audio]
start_endpoints+0x23/0x90 [snd_usb_audio]
snd_usb_substream_playback_trigger+0x7b/0x1a0 [snd_usb_audio]
snd_pcm_common_ioctl+0x1c44/0x2360 [snd_pcm]
snd_pcm_ioctl+0x2e/0x40 [snd_pcm]
__se_sys_ioctl+0x72/0xc0
do_syscall_64+0x4c/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xae
so presumably it's a locking error on that substream spinlock that
snd_pcm_period_elapsed() takes. But at this point I just want to have a
working system so that I can continue the merge window work tomorrow.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the diffstat scatters over the tree, we've got many tree-wide
small changes, but also got quite a few intrusive changes in the
core side. The only ABI-visible core change is the new rawmidi
framing mode support while others are kernel-internal, mostly code
refactoring and/or nice improvements.
Here are some highlights:
Core:
- A new framing access mode for rawmidi to get timestamps
- Cleanup / refactoring of buffer memory management helper code
- Support for automatic negotiation of ASoC DAI formats
- Revival of software suspend for PCM and control core, as a
preliminary work for PCI BAR rescan support
ASoC:
- Accessory detection support for several Qualcomm parts
- Support for IEC958 control with hdmi-codec
- Merging of Tegra machine drivers into a single driver
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
USB-audio:
- Reduction of latency at playback start
- Code cleanup / fixes of usx2y driver
- Scarlett2 mixer code fixes and enhancements
- Quirks for Ozone and Denon devices
HD-audio:
- A few quirks for HP and ASUS machines
- Display power management fixes
Others:
- FireWire code refactoring and enhancements
- Tree-wide trivial coding-style fixes
-----BEGIN PGP SIGNATURE-----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=IN9G
-----END PGP SIGNATURE-----
Merge tag 'sound-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat scatters over the tree, we've got many tree-wide small
changes, but also got quite a few intrusive changes in the core side.
The only ABI-visible core change is the new rawmidi framing mode
support while others are kernel-internal, mostly code refactoring
and/or nice improvements.
Here are some highlights:
Core:
- A new framing access mode for rawmidi to get timestamps
- Cleanup / refactoring of buffer memory management helper code
- Support for automatic negotiation of ASoC DAI formats
- Revival of software suspend for PCM and control core, as a
preliminary work for PCI BAR rescan support
ASoC:
- Accessory detection support for several Qualcomm parts
- Support for IEC958 control with hdmi-codec
- Merging of Tegra machine drivers into a single driver
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
USB-audio:
- Reduction of latency at playback start
- Code cleanup / fixes of usx2y driver
- Scarlett2 mixer code fixes and enhancements
- Quirks for Ozone and Denon devices
HD-audio:
- A few quirks for HP and ASUS machines
- Display power management fixes
Others:
- FireWire code refactoring and enhancements
- Tree-wide trivial coding-style fixes"
* tag 'sound-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: usb-audio: scarlett2: Fix for loop increment in scarlett2_usb_get_config
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 630 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 445 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 450 G8
ALSA: hda/realtek - Add ALC285 HP init procedure
ALSA: hda/realtek - Add type for ALC287
ALSA: scarlett2: Fix scarlett2_*_ctl_put() return values again
ALSA: scarlett2: Fix pad count for 18i8 Gen 3
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 830 G8 Notebook PC
ALSA: firewire-lib: Fix 'amdtp_domain_start()' when no AMDTP_OUT_STREAM stream is found
ASoC: qcom: lpass-cpu: mark IRQ_CLEAR register as volatile and readable
ALSA: hda: Release codec display power during shutdown/reboot
ALSA: hda: Release controller display power during shutdown/reboot
ALSA: hda/realtek: Apply LED fixup for HP Dragonfly G1, too
ASoC: fsl: remove unnecessary oom message
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tegra30: ahub: Use devm_platform_get_and_ioremap_resource()
ASoC: tegra: tegra210_admaif: Use devm_platform_get_and_ioremap_resource()
...
that's just a bunch of data so the diffstat reflects that. Looking beyond that
there's just a bunch of updates all around in various clk drivers. Renesas and
NXP (for i.MX) are two SoC vendors that have a lot of patches in here. Overall
the driver changes look to be mostly enabling more clks and non-critical fixes
that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates clkdev to be
the only implementation of clk_get() and clk_put(). That's a good step in the
right direction to migreate eveerything over to the common clk framework. Now
we don't have to worry about clkdev specific details, they're just part of the
clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is implemented in
only one place in the kernel instead of in drivers/clk/clkdev.c and in
architectures that want their own implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant Clock
Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif, audio,
parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate()
and improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework
-----BEGIN PGP SIGNATURE-----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=YnCF
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round has a diffstat dominated by Qualcomm clk drivers. Honestly
though that's just a bunch of data so the diffstat reflects that.
Looking beyond that there's just a bunch of updates all around in
various clk drivers. Renesas and NXP (for i.MX) are two SoC vendors
that have a lot of patches in here.
Overall the driver changes look to be mostly enabling more clks and
non-critical fixes that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates
clkdev to be the only implementation of clk_get() and clk_put().
That's a good step in the right direction to migreate eveerything over
to the common clk framework. Now we don't have to worry about clkdev
specific details, they're just part of the clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is
implemented in only one place in the kernel instead of in
drivers/clk/clkdev.c and in architectures that want their own
implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant
Clock Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of
round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif,
audio, parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate() and
improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (161 commits)
clk: zynqmp: Handle divider specific read only flag
clk: zynqmp: Use firmware specific mux clock flags
clk: zynqmp: Use firmware specific divider clock flags
clk: zynqmp: Use firmware specific common clock flags
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: hisilicon: Add clock driver for hi3559A SoC
dt-bindings: Document the hi3559a clock bindings
clk: si5341: Add sysfs properties to allow checking/resetting device faults
clk: si5341: Add silabs,iovdd-33 property
clk: si5341: Add silabs,xaxb-ext-clk property
clk: si5341: Allow different output VDD_SEL values
clk: si5341: Update initialization magic
clk: si5341: Check for input clock presence and PLL lock on startup
...
Clang warns:
sound/usb/mixer_scarlett_gen2.c:1189:32: warning: expression result
unused [-Wunused-value]
for (i = 0; i < count; i++, (u16 *)buf++)
^ ~~~~~
1 warning generated.
It appears the intention was to cast the void pointer to a u16 pointer
so that the data could be iterated through like an array of u16 values.
However, the cast happens after the increment because a cast is an
rvalue, whereas the post-increment operator only works on lvalues, so
the loop does not iterate as expected. This is not a bug in practice
because count is not greater than one at the moment but this could
change in the future so this should be fixed.
Replace the cast with a temporary variable of the proper type, which is
less error prone and fixes the iteration. Do the same thing for the
'u8 *' below this if block.
Fixes: ac34df733d ("ALSA: usb-audio: scarlett2: Update get_config to do endian conversion")
Link: https://github.com/ClangBuiltLinux/linux/issues/1408
Acked-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210627051202.1888250-1-nathan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP ProBook 630 G8 using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210701091417.9696-3-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP ProBook 445 G8 using ALC236 codec.
COEF index 0x34 bit 5 is used to control the playback mute LED, but the
microphone mute LED is controlled using pin VREF instead of a COEF index.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210701091417.9696-2-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP ProBook 450 G8 using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210701091417.9696-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This release sees a nice new feature in the core from Morimoto-san,
support for automatic negotiation of DAI formats between the components
on the link. Otherwise the big highlight was the merging of the Tegra
machine drivers into a single driver avoiding a bunch of duplication.
- Support for automatic negotiation of DAI formats.
- Accessory detection support for several Qualcomm parts.
- Support for IEC958 control with hdmi-codec.
- Merging of Tegra machine drivers into a single driver.
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDZzCgACgkQJNaLcl1U
h9DmKAf+IhmeYLxMuSe7uC/BZHQN1PFFHDb9rNyznqYD0kCzgfqvt7RIbbpOB83g
Rw6+SnKWq1k2LOtJc7nVfFXfCrWTCH/GkqH22YoDWUjc2ZLTLE4V/dZhrYzggkjz
qE4bOUNBHUyqO0Xir1iMFCdr9V4+Fc5iYT83FccHB+hF+o8GNcU0MkovUKgiTeuz
EChmQlfsOHxKU6DbRUQrO30plSTaCQZ9CHAOXlGRQnGaYH/99ecav2O7sM1F4SrI
uHR544UuJUiZ26PcZ5M66GvuwAOoSw/v6Tr/OykBulgFUX8wafDcHq7vGK5A6WCE
qGwWpe12E+veMsJjn7wzifryaxJ9zQ==
=F1Zu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.14
This release sees a nice new feature in the core from Morimoto-san,
support for automatic negotiation of DAI formats between the components
on the link. Otherwise the big highlight was the merging of the Tegra
machine drivers into a single driver avoiding a bunch of duplication.
- Support for automatic negotiation of DAI formats.
- Accessory detection support for several Qualcomm parts.
- Support for IEC958 control with hdmi-codec.
- Merging of Tegra machine drivers into a single driver.
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
Mixer control put callbacks should return 1 if the value is changed.
Fix the mute, air, phantom, direct monitor, speaker switch, talkback,
and MSD controls accordingly.
Fix scarlett2_speaker_switch_enable() to not ignore the return value
of scarlett2_sw_hw_change().
Reported-by: Aaron Wolf <aaron@wolftune.com>
Tested-by: Aaron Wolf <aaron@wolftune.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/76643f7ac81aef93351122d07881e30d51dcb1b9.1624798436.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 18i8 Gen 3 has 4 inputs with a pad control, not 2. Update
s18i8_gen3_info.pad_input_count.
Reported-by: Aaron Wolf <aaron@wolftune.com>
Tested-by: Aaron Wolf <aaron@wolftune.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/29a6ce412a42373daab7c96c395560461fcf08c6.1624798436.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The biggest single thing in the diffstat here is a massive overhaul of
the PXA2xx driver from Andy Shevchenko (the IP is still in use on modern
Intel systems), though we also have quite a lot of core work as well:
- Better support for mixing native and GPIO chip selects also from
Andy.
- Support for devices with multiple chip selects from Sebastian
Reichel.
- Helper for polling status registers in spi-mem from Patrice Chotard.
- Support for Renesas RZ/N1 and Rockchip RV1126.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDZ1XMACgkQJNaLcl1U
h9Cw4Qf/dD9K8Psa6oBLrJBVH9L8Bl8UN36UyrZgnZP/cydlPp3MkLpwg9K/mwPV
zqYEm/WcI5mzZ7+RxVwK3fchEBFtlKcIGe2lvfqGBCsVGW8NMtoaiSsCtJ9NoKLk
Q3cjYbERql26sl7fyEx4tCEMGHsRP8XuToyPCm4htSayY6Wh7dsCLpsDPqszeK/c
KnGQItG1hGkXJmy4A47AZqdJlRjeoNxdfnwkE0dxihDmzirE86r4x+QqTVw/OGT/
sE8dtxjuR1bC04oY7I0J3yvgFSA1VxPR+vP0b8KQcXd0pJbTooYppQHDQmltFJ7i
KThmZhDLCsQ8Q/PuWJF7NIPD+gbAoA==
=zcuM
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The biggest single thing in the diffstat here is a massive overhaul of
the PXA2xx driver from Andy Shevchenko (the IP is still in use on
modern Intel systems), though we also have quite a lot of core work as
well:
- Better support for mixing native and GPIO chip selects also from
Andy.
- Support for devices with multiple chip selects from Sebastian
Reichel.
- Helper for polling status registers in spi-mem from Patrice
Chotard.
- Support for Renesas RZ/N1 and Rockchip RV1126"
* tag 'spi-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (86 commits)
spi: core: add dma_map_dev for dma device
spi: convert Xilinx Zynq UltraScale+ MPSoC GQSPI bindings to YAML
spi: Fix self assignment issue with ancillary->mode
spi: spi-sh-msiof: : use proper DMAENGINE API for termination
spi: spi-rspi: : use proper DMAENGINE API for termination
spi: spi-rockchip: add description for rv1126
spi: rockchip: Support SPI_CS_HIGH
spi: rockchip: Support cs-gpio
spi: rockchip: Wait for STB status in slave mode tx_xfer
spi: rockchip: Set rx_fifo interrupt waterline base on transfer item
spi: rockchip: add compatible string for rv1126
spi: spi-sun6i: Fix chipselect/clock bug
spi: dt-bindings: support devices with multiple chipselects
spi: add ancillary device support
spi: xilinx: convert to yaml
spi: convert Cadence SPI bindings to YAML
spi: stm32-qspi: Remove unused qspi field of struct stm32_qspi_flash
spi: add of_device_uevent_modalias support
spi: meson-spicc: fix memory leak in meson_spicc_probe
spi: meson-spicc: fix a wrong goto jump for avoiding memory leak.
...
The HP EliteBook 830 G8 Notebook PC using ALC285 codec which using 0x04 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210625133414.26760-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The intent here is to return an error code if we don't find what we are
looking for in the 'list_for_each_entry()' loop.
's' is not NULL if the list is empty or if we scan the complete list.
Introduce a new 'found' variable to handle such cases.
Fixes: 60dd49298e ("ALSA: firewire-lib: handle several AMDTP streams in callback handler of IRQ target")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/9c9a53a4905984a570ba5672cbab84f2027dedc1.1624560484.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently IRQ_CLEAR register is marked as write-only, however using
regmap_update_bits on this register will have some side effects.
so mark IRQ_CLEAR register appropriately as readable and volatile.
Fixes: da0363f7bf ("ASoC: qcom: Fix for DMA interrupt clear reg overwriting")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210624092153.5771-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the fixes reverted as part of the UMN fallout was actually fine,
however rather than undoing the revert the process that handled all this
stuff resulted in a patch which attempted to add extra error checks
instead. Unfortunately this new change wasn't really based on a good
understanding of the subsystem APIs and bypassed the usual patch flow
without ensuring it was reviewed by people with subsystem knowledge and
was merged as a fix rather than during the merge window.
The effect of the new fix is to upgrade what were previously warnings on
static data in the code to hard errors on that data. If this actually
happens then it would break existing systems, if it doesn't happen then
the change has no effect so this was not a safe change to apply as a fix
to the release candidates. Since the new code has not been tested and
doesn't in practice improve error handling revert it instead, and also
drop the original revert since the original fix was fine. This takes
the driver back to what it was in -rc1.
Fixes: 5e70b8e22b ("ASoC: rt5645: add error checking to rt5645_probe function")
Fixes: 1e0ce84215 ("Revert "ASoC: rt5645: fix a NULL pointer dereference")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210608160713.21040-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
(cherry picked from commit 916cccb507)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A final batch of fixes for v5.13, this is larger than I'd like due to
the fixes for a series of suspend issues that Intel turned up in their
testing this week.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDTZ30ACgkQJNaLcl1U
h9C5dQf6AjDh6y0SfB264cv2kSCLtYsOstSeamrEv3HBjqGiWEDgzfdB5Z+5d+EJ
ScWsfsZ8eMr7WcMZJ+wEGNKxcZO2uHEaC29dpNrDeE4Ffr9hsSucPhJ8Fm+K0qDH
VqX4kDPFY+OiuOf5RipDyAgoHo4zhIeaE9Rgxd4lbNH/xpWtgalN22iyYLpiYZLP
YJk+/8L37ZcKYX3uCImMEe4yseH3AFzGz7yi/tyyWCUP7GEwtWgzv2vadxewjY5E
h12ToqsTMQIrix0ZfMbYW9KJ7ANn6PFBz10vH8XuGbUlBW33pVzqP+Wr9adXGG4N
XLs6wRpbDbdJc3aDpDjA1nRlBl5XEg==
=h2+R
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.13-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Fixes for v5.13
A final batch of fixes for v5.13, this is larger than I'd like due to
the fixes for a series of suspend issues that Intel turned up in their
testing this week.
Hi,
this is v2 from my patchset that add support for the TAS2505 to the tlv320aic32x4 driver.
kind regards,
Claudius
Changes from v1:
- clarified commit message of first patch, which add the type value to the struct
- removed unnecessary code to put and get speaker volume
- removed 'Gain' from 'HP Driver Playback Volume' control
- fixed rebase issues
Claudius Heine (3):
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
.../bindings/sound/tlv320aic32x4.txt | 1 +
sound/soc/codecs/tlv320aic32x4-i2c.c | 22 ++-
sound/soc/codecs/tlv320aic32x4-spi.c | 23 ++-
sound/soc/codecs/tlv320aic32x4.c | 139 +++++++++++++++++-
sound/soc/codecs/tlv320aic32x4.h | 10 ++
5 files changed, 186 insertions(+), 9 deletions(-)
base-commit: 70585216fe
--
2.32.0
Make sure the HDA driver's display power reference is released during
shutdown/reboot.
During the shutdown/reboot sequence the pci device core calls the
pm_runtime_resume handler for all devices before calling the driver's
shutdown callback and so the HDA driver's runtime resume callback will
acquire a display power reference (on HSW/BDW). This triggers a power
reference held WARN on HSW/BDW in the i915 driver's subsequent shutdown
handler, which expects all display power references to be released by
that time.
Since the HDA controller is stopped in the shutdown handler in any case,
let's follow here the same sequence as the one during runtime suspend.
This will also reset the HDA link and drop the display power reference,
getting rid of the above WARN.
Tested on HSW.
v2:
- Fix the build for CONFIG_PM=n (Takashi)
- s/__azx_runtime_suspend/azx_shutdown_chip/
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3618
References: https://lore.kernel.org/lkml/cea1f9a-52e0-b83-593d-52997fe1aaf6@er-systems.de
Reported-and-tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20210623134601.2128663-1-imre.deak@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210617103141.1765-1-thunder.leizhen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for TAS2505 and TAS2521 to the tlv320aic32x4 driver.
The TAS2505 seems to be a stripped down version of the TLV320AIC32X4 so
it makes sense to handle them in the same driver.
Signed-off-by: Claudius Heine <ch@denx.de>
Link: https://lore.kernel.org/r/20210617085230.1851503-3-ch@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
While this driver can already handle different device variants, the
variant information cannot be used in the driver code and therefor
cannot have different code paths depending on the device variant.
This change adds a `type` value into the `aic32x4_priv` structure, that
contains a device variant identifier, which was set when the driver was
bound to the device.
Signed-off-by: Claudius Heine <ch@denx.de>
Link: https://lore.kernel.org/r/20210617085230.1851503-2-ch@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When system enter suspend, the machine driver suspend callback
function will be called, then the cpu driver trigger callback
(SNDRV_PCM_TRIGGER_SUSPEND) be called, it would disable the
interrupt.
But the machine driver suspend and cpu dai driver suspend order
maybe changed, the cpu dai driver's suspend callback is called before
machine driver's suppend callback, then the interrupt is not cleared
successfully in trigger callback.
So need to clear interrupts in cpu dai driver's suspend callback
to avoid such issue.
Fixes: 9cb2b3796e ("ASoC: fsl_spdif: Add pm runtime function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1624365084-7934-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After further investigation, I find out some mistakes for 896 about its
register. This commit fixes it.
Fixes: b431f16f16 ("ALSA: firewire-motu: add support for MOTU 896")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210623075941.72562-10-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After further investigation, I find out some mistakes for 828 about its
register. This commit fixes it.
Fixes: d13d6b284d ("ALSA: firewire-motu: add support for MOTU 828")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210623075941.72562-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current implementation of driver has two similar helper functions for
source detection of sampling clock. This commit merges them as a code
refactoring.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210623075941.72562-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current implementation of driver has several similar helper functions
for packet format detection in protocol version 2.
This commit merges them as code refactoring.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210623075941.72562-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although MOTU Traveler supports AES/EBU source for sampling clock,
current implementation of driver doesn't code it.
This commit adds support for AES/EBU source in protocol version 2.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210623075941.72562-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
