In some cases the standby/enable gpio can be pulled low/high and would not
be connected to a gpio. The current driver implementation will return an
error in these cases. Therefore, make devm_gpiod_get optional.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20211102112120.23637-1-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Link: https://lore.kernel.org/r/20211104065233.1833499-1-yang.guang5@zte.com.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for PHY interface built into ahci controller implemented
in UniPhier Pro4 SoC.
Pro4 SoC distinguishes it from other SoCs as "legacy" SoC, which has GIO
clock line. And Pro4 AHCI-PHY needs to control additional reset lines
("pm", "tx", and "rx").
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1635503947-18250-9-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Amlogic Meson8/8b/8m2 have a built-in HDMI PHY in the HHI register
region. Unfortunately only few register bits are documented. For
HHI_HDMI_PHY_CNTL0 the magic numbers are taken from the 3.10 vendor
kernel.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211020195107.1564533-3-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Many recent Qualcomm platforms comes with native DP and eDP support.
This consists of a controller in the MDSS and a QMP-like PHY.
While similar to the well known QMP block, the eDP PHY only has TX lanes
and the programming sequences are slightly different. Rather than
continuing the trend of parameterize the QMP driver to pieces, this
introduces the support as a new driver.
The registration of link and pixel clocks are borrowed from the QMP
driver. The non-DP link frequencies are omitted for now.
The eDP PHY is very similar to the dedicated (non-USB) DP PHY, but only
the prior is supported for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211103234410.1352424-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Updated DT binding maps just a PHY's register space instead of the whole
DMU block. Accessing a common CRU reg is handled using syscon &
regmap.
The old binding has been deprecated and remains supported as a fallback
method.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211026093716.5567-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage,
reviewed and acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by
the hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in
arm64 for allmodconfig, but that change is on its way through
the drm tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPX2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymUUgCbB4EKysgLuXYdjUalZDx+vvZO4k0AniS14O4k
F+2dVSZ5WX6wumUzCaA6
=bXQM
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage, reviewed and
acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by the
hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in arm64
for allmodconfig, but that change is on its way through the drm
tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
comedi: dt9812: fix DMA buffers on stack
comedi: ni_usb6501: fix NULL-deref in command paths
arm64: errata: Enable TRBE workaround for write to out-of-range address
arm64: errata: Enable workaround for TRBE overwrite in FILL mode
coresight: trbe: Work around write to out of range
coresight: trbe: Make sure we have enough space
coresight: trbe: Add a helper to determine the minimum buffer size
coresight: trbe: Workaround TRBE errata overwrite in FILL mode
coresight: trbe: Add infrastructure for Errata handling
coresight: trbe: Allow driver to choose a different alignment
coresight: trbe: Decouple buffer base from the hardware base
coresight: trbe: Add a helper to pad a given buffer area
coresight: trbe: Add a helper to calculate the trace generated
coresight: trbe: Defer the probe on offline CPUs
coresight: trbe: Fix incorrect access of the sink specific data
coresight: etm4x: Add ETM PID for Kryo-5XX
coresight: trbe: Prohibit trace before disabling TRBE
coresight: trbe: End the AUX handle on truncation
coresight: trbe: Do not truncate buffer on IRQ
coresight: trbe: Fix handling of spurious interrupts
...
In case of error, the function devm_ioremap() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 2ff8a1eeb5 ("phy: Add Sparx5 ethernet serdes PHY driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210909072149.2934047-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix following coccicheck warning:
./drivers/phy/hisilicon/phy-hisi-inno-usb2.c:138:1-23: WARNING: Function
for_each_child_of_node should have of_node_put() before break
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211015080154.16016-1-wanjiabing@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f839f14e24 ("phy: qcom-qmp: Add sc8180x PCIe support") added
SC8180X PCIe tables, but used sm8250_qmp_pcie_serdes_tbl as a serdes
table because of the copy paste error. Commit bfccd9a71a ("phy:
qcom-qmp: Fix sc8180x PCIe definition") corrected part of this mistake
by pointing serdes_tbl to sc8180x_qmp_pcie_serdes_tbl, however the
serdes_tbl_num field was not updated to use sc8180x table. So let's now
fix the serdes_tbl_num field too.
Fixes: bfccd9a71a ("phy: qcom-qmp: Fix sc8180x PCIe definition")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020155604.1374530-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to output received reference clock. Model the received
reference clock as an alternate parent of reference clock driver
clock. When received refclk is selected to output on cmn_refclk_p/m,
this is the internal reference clock driven on the pma_cmn_refclk_int.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210922123735.21927-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When reference clock driver is enabled, either derived or received refclk
is output on cmn_refclk_p/m. Update the reference clock driver
implementation by modelling reference clock driver as a "clock" with
derived reference clock set as its default parent. The support for
received reference clock will be added in a separate patch.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210922123735.21927-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Smatch complains that if of_get_address() returns NULL, then "size"
isn't initialized. Also it would lead to an Oops.
Fixes: 7f78322cdd ("phy: ti: gmii-sel: retrieve ports number and base offset from dt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210914110038.GB11657@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It can be necessary to adjust the phys settings to compensate parasitics.
This patch adds support of new optional properties to configure the tune
interface of the phys of stm32-usbphyc.
Properties are optional, that's why each property is skipped if not
found (-EINVAL).
Phy tuning is restored on resume because if deep low power state is
achieved, phy tuning configuration is reset.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211015161427.220784-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UTMI switch value can be lost during suspend/resume, depending on the power
state reached.
This patch adds resume function to usbphyc, to reconfigure utmi switch
after suspend.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211015161427.220784-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per downstream kernel, beside vdda-pll and vdda-phy-dpdm, vdd is also a
required supply for QUSB2 PHY digital circuit operation. The driver
works right now likely because firmware already sets it up. Add it for
correctness and completeness.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210928022002.26286-3-shawn.guo@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and gif devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922130024.745-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and gif devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210922130017.692-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adding a configuration menu to hold many Broadcom phy drivers
helps to make the menu display more concise.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210923025013.189-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Kirin 970 PHY is somewhat similar to the Kirin 960, but it
does a lot more. Add the needed bits for PCIe to start working on
HiKey 970 boards.
Co-developed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/b7a4ff41b57d861b003f1a00cae81f3d226fbe18.1632814194.git.mchehab+huawei@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We use everywhere "Samsung" and "Exynos", not the uppercase versions.
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924132658.109814-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-11-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=mKyO
-----END PGP SIGNATURE-----
Merge tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- converted Pistachio platform to use MIPS generic kernel
- fixes and cleanups
* tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (29 commits)
MIPS: Malta: fix alignment of the devicetree buffer
MIPS: ingenic: Unconditionally enable clock of CPU #0
MIPS: mscc: ocelot: mark the phy-mode for internal PHY ports
MIPS: mscc: ocelot: disable all switch ports by default
MAINTAINERS: adjust PISTACHIO SOC SUPPORT after its retirement
MIPS: Return true/false (not 1/0) from bool functions
MIPS: generic: Return true/false (not 1/0) from bool functions
MIPS: Make a alias for pistachio_defconfig
MIPS: Retire MACH_PISTACHIO
MIPS: config: generic: Add config for Marduk board
pinctrl: pistachio: Make it as an option
phy: pistachio-usb: Depend on MIPS || COMPILE_TEST
clocksource/drivers/pistachio: Make it selectable for MIPS
clk: pistachio: Make it selectable for generic MIPS kernel
MIPS: DTS: Pistachio add missing cpc and cdmm
MIPS: generic: Allow generating FIT image for Marduk board
MIPS: locking/atomic: Fix atomic{_64,}_sub_if_positive
MIPS: loongson2ef: don't build serial.o unconditionally
MIPS: Replace deprecated CPU-hotplug functions.
MIPS: Alchemy: Fix spelling contraction "cant" -> "can't"
...
Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here, notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanna labs driver updates in this pull request,
that will probably come later before -rc1 is out in a different request.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+Kyw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymlpACg0JM+hSeo8T5GtwZksZ1QXXQfh8sAoK6Dt6xF
e62OQuuMFT0Un0qOflZk
=emH+
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here,
notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanalabs driver updates in this pull request,
that will probably come later before -rc1 is out in a different
request.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
Revert "bus: mhi: Add inbound buffers allocation flag"
misc/pvpanic: fix set driver data
VMCI: fix NULL pointer dereference when unmapping queue pair
char: mware: fix returnvar.cocci warnings
parport: remove non-zero check on count
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
phy: qcom-qmp: Add support for SM6115 UFS phy
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qmp: Provide unique clock names for DP clocks
lkdtm: remove IDE_CORE_CP crashpoint
lkdtm: replace SCSI_DISPATCH_CMD with SCSI_QUEUE_RQ
coresight: Replace deprecated CPU-hotplug functions.
Documentation: coresight: Add documentation for CoreSight config
coresight: syscfg: Add initial configfs support
coresight: config: Add preloaded configurations
coresight: etm4x: Add complex configuration handlers to etmv4
coresight: etm-perf: Update to activate selected configuration
...
Armada 3700 does not support RXAUI, XFI and neither SFI. Remove unused
macros for these unsupported modes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: eb6a1fcb53 ("phy: mvebu-cp110-comphy: Add SMC call support")
Fixes: c2afb2fef5 ("phy: mvebu-cp110-comphy: Rename the macro handling only Ethernet modes")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tables and constants for init sequences for UFS QMP phy found in
SM4250/6115 SoC. The phy is a variation of the v2 phy, but is mistakenly
labeled as v3-660 in downstream sources.
QSERDES COM, RX, TX registers match fully existing v2 registers, with
a few additions. PCS registers don't have much in common, but there are
no clashes with existing ones so new registers were added to existing v2
PCS pack.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20210821155657.893165-3-iskren.chernev@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB/DP combo PHY exposes the "qmp_dp_phy_pll_link_clk" and
"qmp_dp_phy_pll_vco_div_clk" clocks, that are consumed by the display
clock controller. But for boards with multiple enabled QMP USB/DP combo
instances the hard coded names collides - and hence only the first
probed device is allowed to register.
Given that clocks are no longer reference globally by name and it's
possible to replace the hard coded names by something unique, but still
user friendly.
The two new clock names are based on dev_name() and results in names
such as "88ee000.phy::link_clk" and "88ee000.phy::vco_div_clk".
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210722030738.3385821-1-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PHY initialization for USB is required on linux boot or when
gt lane is changed from the current one and it is applicable
on PLL lock too.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20210818084311.2643986-1-piyush.mehta@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
devm_phy_create can return -EPROBE_DEFER if the vbus-supply is not ready
yet. Silence this warning as the driver framework will re-attempt
registering the PHY. Use dev_err_probe() for phy resources to indicate
the deferral reason when waiting for the resource to come up.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20210817041548.1276-7-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Power off the PHY by putting it into reset mode.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20210817041548.1276-6-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
