Using a single definition for the physical and virtual address register for all
variants boards clps711x. This patch also includes the use of a single function
clps_read/write in some units.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
tty_unlock is used on all other exits from the function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver anticipates pch_uart_verify_port() is not called
during installation.
However, actually pch_uart_verify_port() is called during
installation.
As a result, memory access violation occurs like below.
0. initial value: use_dma=0
1. starup()
- dma channel is not allocated because use_dma=0
2. pch_uart_verify_port()
- Set use_dma=1
3. UART processing acts DMA mode because use_dma=1
- memory access violation occurs!
This patch fixes the issue.
Solution:
Whenever pch_uart_verify_port() is called and then
dma channel is not allocated, the channel should be allocated.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result
of call disable_irq from ISR. synchronize_irq waits for end of interrupt
and goes to infinite loop. This patch fix this problem.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tty and serial fixes for 3.4-rc2.
Most important here is the pl011 fix, which has been reported by about
100 different people, which means more people use it than I expected :)
There are also some 8250 driver reverts due to some problems reported by
them. And other minor fixes as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+HVDgACgkQMUfUDdst+ymKngCbBIqGrmq5PiDEV7JnkpLRcCEy
DQoAn1XH+Y4NR0Wu121AkJ7UwE8CiXSg
=h7iL
-----END PGP SIGNATURE-----
Merge tag 'tty-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial fixes from Greg KH:
"Here are some tty and serial fixes for 3.4-rc2.
Most important here is the pl011 fix, which has been reported by about
100 different people, which means more people use it than I expected
:)
There are also some 8250 driver reverts due to some problems reported
by them. And other minor fixes as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pch_uart: Add Kontron COMe-mTT10 uart clock quirk
pch_uart: Fix MSI setting issue
serial/8250_pci: add a "force background timer" flag and use it for the "kt" serial port
Revert "serial/8250_pci: setup-quirk workaround for the kt serial controller"
Revert "serial/8250_pci: init-quirk msi support for kt serial controller"
tty/serial/omap: console can only be built-in
serial: samsung: fix omission initialize ulcon in reset port fn()
printk(): add KERN_CONT where needed in hpet and vt code
tty/serial: atmel_serial: fix RS485 half-duplex problem
tty: serial: altera_uart: Check for NULL platform_data in probe.
isdn/gigaset: use gig_dbg() for debugging output
omap-serial: Fix the error handling in the omap_serial probe
serial: PL011: move interrupt clearing
Add UART clock quirk for the Kontron COMe-mTT10 module.
The board has previously been called nanoETXexpress-TT, therefore this
is also checked.
As suggested by Darren Hart the comparison in this patch version is
placed after the FRI2 checks to ensure it will also work with possible
upcoming changes to the FRI2 firmware.
This patch follows the patchset submitted by Darren Hart at
commit a46f5533ec.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch (MSI setting) is not enough.
commit e463595fd9
Author: Alexander Stein <alexander.stein@systec-electronic.com>
Date: Mon Jul 4 08:58:31 2011 +0200
pch_uart: Add MSI support
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To enable MSI mode, PCI bus-mastering must be enabled.
This patch enables the setting.
cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround dropped notifications in the iir register. Register reads
coincident with new interrupt notifications sometimes result in this
device clearing the interrupt event without reporting it in the read
data.
The serial core already has a heuristic for determining when a device
has an untrustworthy iir register. In this case when we apriori know
that the iir is faulty use a flag (UPF_BUG_THRE) to bypass the test and
force usage of the background timer.
[stable: 3.3.x]
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Reported-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Tested-by: Nhan H Mai <nhan.h.mai@intel.com>
Tested-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 448ac154c9.
The semantic of UPF_IIR_ONCE is only guaranteed to workaround the race
condition in the kt serial's iir register if the only source of
interrupts is THRE (fifo-empty) events. An modem status event at the
wrong time can again cause an iir read to drop the 'empty' status
leading to a hang. So, revert this in preparation for using the
existing "I don't trust my iir register" workaround in the 8250 core
(UART_BUG_THRE).
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e86ff4a63c.
This tried to enforce the semantics of one interrupt per iir read of the
THRE (transmit-hold empty) status, but events from other sources
(particularly modem status) defeat this guarantee.
This change also broke 8250_pci suspend/resume support as
pciserial_resume_ports() re-runs .init() quirks, but does not run
.exit() quirks in pciserial_suspend_ports() leading to reports like:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:16.3/msi_irqs'
...and a subsequent crash. The mismatch of init/exit at suspend/resume
seems like a bug in its own right.
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the omap serial driver is built as a module, we must
not allow the console driver to be selected, because consoles
can not be loadable modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix omission initialize ulcon in s3c24xx_serial_resetport(),
reset port function in drivers/tty/serial/samsung.c. It has
been happened from commit 0dfb3b41("serial: samsung: merge
all SoC specific port reset functions")
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@vger.kernel.org> [3.3]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A prototype for kmsg records instead of a byte-stream buffer revealed
a couple of missing printk(KERN_CONT ...) uses. Subsequent calls produce
one record per printk() call, while all should have ended up in a single
record.
Instead of:
ACPI: (supports S0 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
hpet0: at MMIO 0xfed00000, IRQs 2 , 8 , 0
It prints:
ACPI: (supports S0
S5
)
ACPI: PCI Interrupt Link [LNKA] (IRQs
5
*10
11
)
hpet0: at MMIO 0xfed00000, IRQs
2
, 8
, 0
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On our custom board, we are using RS485 in half-duplex mode on an AT91SAM9G45.
SER_RS485_RX_DURING_TX is not set as we do not want to receive the data we
transmit (our transceiver will receive transmitted data).
Although the current driver attempts to disable and enable the receiver at the
appropriate points, incoming data is still loaded into the receive register
causing our code to receive the very last byte that was sent once the receiver
is enabled.
I ran this by Atmel support and they wrote: "The issue comes from the fact
that you disable the PDC/DMA Reception and not the USART Reception channel. In
your case, the[n] you will still receive data into the USART_RHR register, and
maybe you [h]ave the overrun flag set. So please disable the USART reception
channel."
The following patch should force the driver to enable/disable the receiver via
RXEN/RXDIS fields of the USART control register. It fixed the issue I was
having.
Signed-off-by: Gabe Siftar <gabe.siftar@getingeusa.com>
[nicolas.ferre@atmel.com: slightly modify commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow altera_jtag_uart. This fixes a crash if there is a mistake in the DTS.
Signed-off-by: Yuriy Kozlov <ykozlov@ptcusa.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch does the following
- The pm_runtime_disable is called in the remove not in the error
case of probe.The patch calls the pm_runtime_disable in the error
case.
- Calls pm_runtime_put in the error case.
- The up is not freed in the error path. Fix the memory leak by using
devm_* so that the memory need not be freed in the driver.
- Also the iounmap is not called fix the same by calling using devm_ioremap.
- Make the name of the error tags more meaningful.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk99uBgACgkQGkmNcg7/o7hglwCgqi6CE7i5gyneNYBn2ocRps4O
y1UAoMSIscO6YWcHPuxOiNBbJYUy/jMI
=SEO8
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
Commit 360f748b204275229f8398cb2f9f53955db1503b
"serial: PL011: clear pending interrupts"
attempts to clear interrupts by writing to a
yet-unassigned memory address. This fixes the issue.
The breaking patch is marked for stable so should be
carried along with the other patch.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: stable <stable@vger.kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Reported-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change send_sig_all() to use do_send_sig_info(SEND_SIG_FORCED) instead
of force_sig(SIGKILL). With the recent changes we do not need force_ to
kill the CLONE_NEWPID tasks.
And this is more correct. force_sig() can race with the exiting thread,
while do_send_sig_info(group => true) kill the whole process.
Some more notes from Oleg Nesterov:
> Just one note. This change makes no difference for sysrq_handle_kill().
> But it obviously changes the behaviour sysrq_handle_term(). I think
> this is fine, if you want to really kill the task which blocks/ignores
> SIGTERM you can use sysrq_handle_kill().
>
> Even ignoring the reasons why force_sig() is simply wrong here,
> force_sig(SIGTERM) looks strange. The task won't be killed if it has
> a handler, but SIG_IGN can't help. However if it has the handler
> but blocks SIGTERM temporary (this is very common) it will be killed.
Also,
> force_sig() can't kill the process if the main thread has already
> exited. IOW, it is trivial to create the process which can't be
> killed by sysrq.
So, this patch fixes the issue.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The keyboard on my SUN SPARCstation 5 no longer worked.
The culprint was: d4e33fac24
("serial: Kill off NO_IRQ")
Fix up logic for no irq / irq so the keyboard works again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Follows the 8250 change for pretty much the same rationale.
See commit "serial: use serial_port_in/out vs serial_in/out in 8250".
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk91TL0ACgkQGkmNcg7/o7hEjwCgmuz6QQKkow7e5q0x7DR5Z2NH
1YoAn3TpODDmpaBiou26uMRPhcR6e1qC
=JCA0
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (25 commits)
sh: Support I/O space swapping where needed.
sh: use set_current_blocked() and block_sigmask()
sh: no need to reset handler if SA_ONESHOT
sh: intc: Fix up section mismatch for intc_ack_data
sh: select ARCH_DISCARD_MEMBLOCK.
sh: Consolidate duplicate _32/_64 unistd definitions.
sh: ecovec: switch SDHI controllers to card polling
sh: Avoid exporting unimplemented syscalls.
sh: add platform_device for RSPI in setup-sh7757
SH: pci-sh7780: enable big-endian operation.
serial: sh-sci: fix a race of DMA submit_tx on transfer
sh: dma: Collect up CHCR of SH7763, SH7764, SH7780 and SH7785
sh: dma: Collect up CHCR of SH7723 and SH7730
sh/next: Fix build fail by asm/system.h in asm/bitops.h
arch/sh/drivers/dma/{dma-g2,dmabrg}.c: ensure arguments to request_irq and free_irq are compatible
sh: cpufreq: Wire up scaling_available_freqs support.
sh: cpufreq: notify about rate rounding fallback.
sh: cpufreq: Support CPU clock frequency table.
sh: cpufreq: struct device lookup from CPU topology.
sh: cpufreq: percpu struct clk accounting.
...
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
When DMA is enabled, sh-sci transfer begins with
uart_start()
sci_start_tx()
if (cookie_tx < 0) schedule_work()
Then, starts DMA when wq scheduled, -- (A)
process_one_work()
work_fn_rx()
cookie_tx = desc->submit_tx()
And finishes when DMA transfer ends, -- (B)
sci_dma_tx_complete()
async_tx_ack()
cookie_tx = -EINVAL
(possible another schedule_work())
This A to B sequence is not reentrant, since controlling variables
(for example, cookie_tx above) are not queues nor lists. So, they
must be invoked as A B A B..., otherwise results in kernel crash.
To ensure the sequence, sci_start_tx() seems to test if cookie_tx < 0
(represents "not used") to call schedule_work().
But cookie_tx will not be set (to a cookie, also means "used") until
in the middle of work queue scheduled function work_fn_tx().
This gap between the test and set allows the breakage of the sequence
under the very frequently call of uart_start().
Another gap between async_tx_ack() and another schedule_work() results
in the same issue, too.
This patch introduces a new condition "cookie_tx == 0" just to mark
it is "busy" and assign it within spin-locked region to fill the gaps.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fMC+
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: device tree work" from Arnd Bergmann:
"Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
In preparation to convert SA1100 to sparse irq, set .nr_irqs for each machine
and explicitly include mach/irqs.h as needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJPa7EVAAoJEKurIx+X31iBADgP/1eHhyb4A2ULOk19MhrEAb3/
myoz76qVZvFC7i/5kmtkpAZqCYNnNfiBzr0vpd6MNq9mgFx5jna/IiaV8cZ08kcj
JPknyrAoK8IgGgVQmi+pSHoaiNRAjnvkLwBsadLSFGmcjpi1BYlzmQrFYvMh5GAN
J6j7+2Sv2YNec2QthZZ56L29QqQnbzg0DfS6ZTcOLSvitCnAsUb54Hoi/saK1c9r
loUdWeVen8FPBSTfyqFtJLWJj1Yo3KxVoUgME+f7TeBQNRfihzDhMLuK+IQ5Bsp5
/Z4+Pi4MxiTccYETWCLFWyS9cheK7tfR/SOpEd+XQYx7BQ2gLp/WMNd3q1iUTsg+
AXr3/XOtmKWKAlu6Wy/oFUOjokPVm/yl9MSB6Io1bmlYfaCmb8I+Eyr+fJzPKLyI
wVd+SQl02Z2PlC9dnr73Wu+bCrx0u9xQncucNEpZIpBZLGeuU0sPP0Y7nCGAOL5C
NL7yQmb45pvT7kvzBfrrFSqEfWccycIL+CJw9kb+k1aspTxT0YBZPbpNTKj83aXW
H4KAF9Av/ZHeacriDpxrywwMtTsTS/xLhxEdHB/XEzjkGLuB0R7ZlzvTSuLBbm/1
fu8/bty4ehOHRqACIuNNMGbdIZ5ruThylSC4Yx2a3JRIJISZS/Bo/0mU5zLRRaH+
XuEw3+mfhLq9oU8SdAug
=78St
-----END PGP SIGNATURE-----
Merge tag 'ia64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull miscellaneous Itanium patches from Tony Luck.
The conflicts in arch/ia64/hp/sim/simserial.c were due to patches to
simserial that had alredy been included (with lots of further cleanups)
in the serial tree.
* tag 'ia64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
Documentation/kernel-parameters: remove inttest parameter
[IA64] Fix ISA IRQ trigger model and polarity setting
[IA64] Fix a couple of warnings for EXPORT_SYMBOL
[IA64] Check return from device_register() in cx_device_register()
[IA64] Fix warning from machine_kexec.c
[IA64] simserial, bail out when request_irq fails
[IA64] hpsim, initialize chip for assigned irqs
[IA64] simserial, include some headers
[IA64] hpsim, fix SAL handling in fw-emu
[IA64] genirq fixup for SGI/SN
[IA64] disable interrupts when exiting from ia64_mca_cmc_int_handler()
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPazYTAAoJEEEQszewGV1z09IQAIcsnFO5s7XfvfXhwNCliiKp
myVMJdYcx8GSOg5Oif9uektcBi0gB2ppegxVYDxDq8FZqZQ4d3pYDZel3tDBGKJI
9ZXemh1iIeXwLZBXSENxn0NZokAZVDiyBqi50zsINV+riFfyzL9Ai7o3YkEx9xBG
nJ6S9wthzeF2qF8/NBvMYgCefZXIKJ8miwVrb9MusWUBfeAY7F8jVNlK9Asp9ruv
XEC+WcrWRttB/8+5z3FkPPtEnJ+0Y2p6e6+hn8Cel0UWb4+WDijumO+hTyIiNYSc
ryzFMqX18L8taaDhxQZ1kRDL5S7Qu7N3HYu+4wBvPI3D81MroS5frJbUwPcD8WsK
Pw/NZtAwJhp4B9/LVOOoAyBoRTfeIwrbp+ou2zF5m70hpBD5D1mN/2xVBBQgjm9T
oY9jNoJ2PhZP74fO4jdf4iMW1j5ZmzwxLXlpT3vGJeONIUg2hE0FJjzoeOjRsUtO
iC0m7Q1AbJpIcjJlcK+gV/ZclaOWy4iDXDXFs4A3XA+ryf/ylDL5G+c/1Qu6CMyF
4AhKs78Fg7agtVYX/QYuie9BbasRjipxiPc0t3/46Abs7WRzvpmBWWktFE4yy980
93jLyog0VROHIOl974Fn0GrNJeNUTavc5DEd32zlc7AiAibOzyuRztwJ5GZbuZAN
SE0VyQBIIdkaF51XV+IO
=Gg7v
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates for v3.4 from Linus Walleij (*):
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
* tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
ARM: u300: configure some pins as an example
pinctrl: support pinconfig on the U300
pinctrl/coh901: use generic pinconf enums and parameters
pinctrl: introduce generic pin config
pinctrl: fix error path in pinconf_map_to_setting()
pinctrl: allow concurrent gpio and mux function ownership of pins
pinctrl: forward-declare struct device
pinctrl: split pincontrol states into its own header
pinctrl: include machine header to core.h
ARM: tegra: Select PINCTRL Kconfig variables
pinctrl: add a driver for NVIDIA Tegra
pinctrl: Show selected function and group in pinmux-pins debugfs
pinctrl: enhance mapping table to support pin config operations
pinctrl: API changes to support multiple states per device
pinctrl: add usecount to pins for muxing
pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
pinctrl: fix and simplify locking
pinctrl: fix the pin descriptor kerneldoc
pinctrl: assume map table entries can't have a NULL name field
pinctrl: introduce PINCTRL_STATE_DEFAULT, define hogs as that state
...
(*) What is it with all these Linuses these days? There's a Linus at
google too. Some day I will get myself my own broadsword, and run
around screaming "There can be only one".
I used to be _special_ dammit. Snif.
- PV multiconsole support, so that there can be hvc1, hvc2, etc;
- P-state and C-state power management driver that uploads said
power management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ0qkAAoJEFjIrFwIi8fJjCgH/jeJ39E8ML8DP9tCS2HQnMqM
uTEjLcqvoJ7sEhHvtBLPeG2p0jyBvOWjLbSc7P8nESBAMPvSYol8L6WqfWrdSU4r
lHrma2sg9UYzRog5NyxAgkp7bBsBBFOnhVL3Cxb5Ig78cPWzeSWGpqGZ8M/d51Wf
1iE0tHuU4DpN+fg1SZqPqEm8ecEJ/eSrVTnyTx/Qo2Ak+Zw98SqzX7SV5lo8mudd
WFL1F2K9FyTNk79ndGhqFt36x6nEbFgMLbmCDWumLuWN6bMd1Uq0wNkCqW4F1h28
3yqnY+rfQh4y3eXK1B9nttCUTs+/66U5ZWrT6B1IJumGTAIqcWfgeUX/Vn/HVC4=
=tfMc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
Merge first batch of patches from Andrew Morton:
"A few misc things and all the MM queue"
* emailed from Andrew Morton <akpm@linux-foundation.org>: (92 commits)
memcg: avoid THP split in task migration
thp: add HPAGE_PMD_* definitions for !CONFIG_TRANSPARENT_HUGEPAGE
memcg: clean up existing move charge code
mm/memcontrol.c: remove unnecessary 'break' in mem_cgroup_read()
mm/memcontrol.c: remove redundant BUG_ON() in mem_cgroup_usage_unregister_event()
mm/memcontrol.c: s/stealed/stolen/
memcg: fix performance of mem_cgroup_begin_update_page_stat()
memcg: remove PCG_FILE_MAPPED
memcg: use new logic for page stat accounting
memcg: remove PCG_MOVE_LOCK flag from page_cgroup
memcg: simplify move_account() check
memcg: remove EXPORT_SYMBOL(mem_cgroup_update_page_stat)
memcg: kill dead prev_priority stubs
memcg: remove PCG_CACHE page_cgroup flag
memcg: let css_get_next() rely upon rcu_read_lock()
cgroup: revert ss_id_lock to spinlock
idr: make idr_get_next() good for rcu_read_lock()
memcg: remove unnecessary thp check in page stat accounting
memcg: remove redundant returns
memcg: enum lru_list lru
...
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
The oom killer chooses not to kill a thread if:
- an eligible thread has already been oom killed and has yet to exit,
and
- an eligible thread is exiting but has yet to free all its memory and
is not the thread attempting to currently allocate memory.
SysRq+F manually invokes the global oom killer to kill a memory-hogging
task. This is normally done as a last resort to free memory when no
progress is being made or to test the oom killer itself.
For both uses, we always want to kill a thread and never defer. This
patch causes SysRq+F to always kill an eligible thread and can be used to
force a kill even if another oom killed thread has failed to exit.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
so remove the code that tests for it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty layer,
and a number of patches from Alan to help try to wrestle the vt layer
into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9nihQACgkQMUfUDdst+ylXTQCdFuwVuZgjCts+xDVa1jX2ac84
UogAn3Wr+P7NYFN6gvaGm52KbGbZs405
=2b/l
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
